Network problems 10.8 and mavericks both

Just got a new 27" iMac and have set it up fine on 10.8, i have now upgraded to Mavericks.
Now we have a NAS network drive for sharing files in the office, we have used this between macs and PCs for a few years now without problem, it has a network volume called 'guestshare' which doesnt require a password or login to access...
now i have had macs of all sizes and ages access this, the older ones OSX 10.4 and previous, i used Go>Connect to Server and selected the drive and was asked which volume i wanted to mount, then selected the 'guestshare' to get access, it appeared as a network drive on the desktop.
the newer one 10.5 i think, i simply went through the finder window, and network was available at the side, and you could navigate into the drive and select guestshare just like any folder on the computer no problem.
now my new iMac had 10.8 and i couldnt see any obvious quick network in the finder window, so i tried the old way Go > connect to server, this works but once connected the folder has a no entry label and i get the message:
"The folder "guest-share" can't be opened because you don't have permission to see its contents."
I have now upgraded to Maverwicks, thinking may aswell try that to see if that fixes it, but im getting same problem
Any ideas why this would be?

i just checked on the other mac and it lists the server as:
cifs://workgroup;user1@millgaetdrive1/guest-share
(the millgaetdrive1 is the name of the NAS drive)

Similar Messages

Network problems with TC and windows vista

When I try to transfer data from my laptop using Windows vista to the TC, I get an network error message after a few seconds saying the computer is not connected to the network. I have no problems transferring small files (that take less than a few seconds to transfer) and the external router, my laptop and the TC are located close to each other. I tried almost everything but i don't know what the problem is.
Any suggestions?

Hello Bastiaandp. Welcome to the Apple Discussions!
There is quite a bit of dialogue going around the Internet about Windows Vista & Windows 7 when it comes to file sharing with either the Apple AirPorts or Time Capsules. Most of this dialogue seems to be revolving around the version of SMB used by the newer Microsoft OSs and that used by these routers for files sharing.
A number of suggested solutions have been proposed, but none at this time, have provided a "permanent" solution. I too have experienced this same issue and have tried a number of these solutions. What finally worked for me was to make sure that: 1) The Workgroup name used on my Win 7 computer exactly matched the Workgroup name setting on the Disks > File Sharing tab within the AirPort Utility for my base station, & 2) That this name did NOT include any spaces. In my case, I used WORKGROUP for both settings.
Since doing so over six months ago, I have had no problems copying/moving files between my PC and the AirPort, regardless of their size.

Problems with Bonjour and Mavericks

I actually have problems getting a Network printer working under Mavericks on a brand new Macbook Pro.
The Printer is an HP Officejet 8500, wich is connected to a Qnap TS-269.
In the config of the NAS, Bonjour is activated.
When I now try to install it, I can see it listed as available printer.
Its named "NAS (Aiprint)", and the installtion seems to work properly.
I choose the right driver (v 3.3.3) and tried to print a test page, wich results in egypt hieroglyphics.
I tried all possible varitions, like using generic postscript printer, the airprint driver, but all leads to the same result.
Installing it manually as IPP-Printer (wich is defined by the NAS-Manual) doesnt work at all.
With all other machines, windows and various osx versions, it works fine.
Any Ideas? The update for that printer-driver from HP doenst help too, seems like its only fixing a bug for USB-connections.

Hi DBCTV,
deathbychinatv wrote:
This forum is depressing. Everybody is citing freeze and crash problems with Premier but noone has a solution.
Actually, what we are suggesting in this forum is to change the permissions on your preferences folder: fixing permissions problem that impedes start of Adobe applications | After Effects region of interest
That has solved a lot of people's problems.
deathbychinatv wrote:
Premier -- get on the stick! I loaded 2014cc and my new Mac Pro behaves like a two-year old. Totally useless. I switched to premier to get away from FCP and this is what I get?
When I try to export movies, I get "system out of application memory" message as it crashes. Premier and "kernel" task show huge consumption of memory on activity monitor.
I'm really sorry your issue is problematic and it frustrating you. However, I remind you that we are people too. We are doing our best to solve any issues that do crop up. I am not completely familiar with the issues that you are having but I will do my best for you.
deathbychinatv wrote:
Apparently there are no issues on machines using Lion OS but Mavericks and Premier don't play well together.
Adobe needs to figure this out quick or it will lose a bunch of customers.
Are you running OS X 10.9.4? Updated Premiere Pro to the latest version (a new one just came out). Please try that if you have not. Also, please remove any third party plug-ins. After doing so, please check and see if your system is behaving normally.
Keep in mind that your issue, and many others, are not solely Adobe issues. We are working with other partners, like Apple, in solving certain problems. With that in mind, I hope we can help solve your issue as soon as possible. Thanks in advance for any other info you can give: FAQ: What information should I provide when asking a question on this forum?
Thanks,
Kevin

Printing problems with acrobat and Mavericks

We just got a new Mac Mini to replace an old iMac to drive our printers. We normally print from Acrobat Pro 9 ( 10.6.8 & 10.8.5 ) and have no problems. We migrated everything over to the Mini, which is running Mavericks, and now when we print a 2 page document the 2nd page is printing 180 degrees turned around. Printed the same file from another Mac with no problems. I've heard that Mavericks will only run Acrobat Pro XI. This is insane, that's like $450! Could it be a driver or something simple that I can't see for the life of me? BTW, this Mini will be running 10 printers at once, the old one did it.

Have you reset the printing system…
http://support.apple.com/kb/PH14141
Does Preview do any better? That will indicate if it's the printer driver or something in the application's printing system.
It would be worth checking that the printer drivers are up to date - a migrated driver may not be appropriate for 10.9.

[solved]partially working network, problems with ssl and irc

Hi,
for a weird reason I can't access any websites with https anymore nor can i connect to any irc servers with irssi and connection attempts with ssh time out. The system is up2date and I am using kdemod as DE.
My rc.conf looks like this:
# /etc/rc.conf - Main Configuration for Arch Linux
# LOCALIZATION
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime", any other value will result
# in the hardware clock being left untouched (useful for virtualization)
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
LOCALE="de_DE.utf8"
HARDWARECLOCK="localtime"
TIMEZONE="Europe/Berlin"
KEYMAP="de"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
# HARDWARE
# MOD_AUTOLOAD: Allow autoloading of modules at boot and when needed
# MOD_BLACKLIST: Prevent udev from loading these modules
# MODULES: Modules to load at boot-up. Prefix with a ! to blacklist.
# NOTE: Use of 'MOD_BLACKLIST' is deprecated. Please use ! in the MODULES array.
MOD_AUTOLOAD="yes"
#MOD_BLACKLIST=() #deprecated
MODULES=(!b44 !mii !ipw2200 !libipw !ac97_bus !snd-mixer-oss !snd-pcm-oss !snd-page-alloc !snd-pcm !snd-timer !snd !snd-ac97-codec !snd-intel8x0 !snd-intel8x0m !soundcore b44 mii ipw2200 libipw ac97_bus snd-mixer-oss snd-pcm-oss snd-page-alloc snd-pcm snd-timer snd snd-ac97-codec snd-intel8x0 snd-intel8x0m soundcore)
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# NETWORKING
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
HOSTNAME="horst-lp"
# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available interfaces.
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
# - no hyphens in your interface names - Bash doesn't like it
eth0="dhcp"
# Wireless: See network profiles below
#Static IP example
#eth0="dhcp"
eth0="dhcp"
INTERFACES=(!eth0 !eth1 !wlan0)
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
gateway="default gw 192.168.0.1"
ROUTES=(!gateway)
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
# Network profiles are found in /etc/network.d
# This now requires the netcfg package
#NETWORKS=(main)
# DAEMONS
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
DAEMONS=(syslog-ng hal !network networkmanager avahi-daemon avahi-dnsconfd alsa cdemud kdm samba mpd lighttpd)
Earlier I had some problems with not resolving addresses, which I somehow got rid of. At the time I blamed my isp.
Perhaps something broke when I had a program running in wine to play with a car too and I had to switch the laptop off bc it didn't want to react anymore.
thx for reading
e: I don't know why, but it worked when I started Arch this morning.. while it didn't yesterday although everything worked correctly on my other PCs.
Last edited by dt (2009-11-07 09:02:46)

Hi,
for a weird reason I can't access any websites with https anymore nor can i connect to any irc servers with irssi and connection attempts with ssh time out. The system is up2date and I am using kdemod as DE.
My rc.conf looks like this:
# /etc/rc.conf - Main Configuration for Arch Linux
# LOCALIZATION
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime", any other value will result
# in the hardware clock being left untouched (useful for virtualization)
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
LOCALE="de_DE.utf8"
HARDWARECLOCK="localtime"
TIMEZONE="Europe/Berlin"
KEYMAP="de"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
# HARDWARE
# MOD_AUTOLOAD: Allow autoloading of modules at boot and when needed
# MOD_BLACKLIST: Prevent udev from loading these modules
# MODULES: Modules to load at boot-up. Prefix with a ! to blacklist.
# NOTE: Use of 'MOD_BLACKLIST' is deprecated. Please use ! in the MODULES array.
MOD_AUTOLOAD="yes"
#MOD_BLACKLIST=() #deprecated
MODULES=(!b44 !mii !ipw2200 !libipw !ac97_bus !snd-mixer-oss !snd-pcm-oss !snd-page-alloc !snd-pcm !snd-timer !snd !snd-ac97-codec !snd-intel8x0 !snd-intel8x0m !soundcore b44 mii ipw2200 libipw ac97_bus snd-mixer-oss snd-pcm-oss snd-page-alloc snd-pcm snd-timer snd snd-ac97-codec snd-intel8x0 snd-intel8x0m soundcore)
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# NETWORKING
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
HOSTNAME="horst-lp"
# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available interfaces.
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
# - no hyphens in your interface names - Bash doesn't like it
eth0="dhcp"
# Wireless: See network profiles below
#Static IP example
#eth0="dhcp"
eth0="dhcp"
INTERFACES=(!eth0 !eth1 !wlan0)
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
gateway="default gw 192.168.0.1"
ROUTES=(!gateway)
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
# Network profiles are found in /etc/network.d
# This now requires the netcfg package
#NETWORKS=(main)
# DAEMONS
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
DAEMONS=(syslog-ng hal !network networkmanager avahi-daemon avahi-dnsconfd alsa cdemud kdm samba mpd lighttpd)
Earlier I had some problems with not resolving addresses, which I somehow got rid of. At the time I blamed my isp.
Perhaps something broke when I had a program running in wine to play with a car too and I had to switch the laptop off bc it didn't want to react anymore.
thx for reading
e: I don't know why, but it worked when I started Arch this morning.. while it didn't yesterday although everything worked correctly on my other PCs.
Last edited by dt (2009-11-07 09:02:46)

Serious problems with Adobe and Mavericks 10.9.3

Serious problems with Adobe, crashes, no video export, video deteriorated by a line of pixels.
Video card error from when turning computer on. Overheat when exporting from Premiere or encoder.
Issues also with davinci resolve, output corrupted...
Anybody has a solution?

The issue is now solved. I closed all open apps, and then tried once more to reinstall OS X after restart apple key + R and now everything is fine again.
TUVVH4 wrote:
TUVVH4 wrote:
I have an issue with the Mavericks 10.9.3 update. After restarting it didn't finish the update, but were just running with the grey Apple screen. I was forced to shot down, since my iMac got very hot. Then I needed to reload everything from my Timecapsule. I have tried several times, and everytime I needed to reload reload etc. from Timecapsule. After my lateste reload Safari, Time Machine and System Settings are missing and are replaced by a "?" i the program bar!!! Help anybody!
I have an issue with the Mavericks 10.9.3 update. After restarting it didn't finish the update, but were just running with the grey Apple screen. I was forced to shot down, since my iMac got very hot. Then I needed to reload everything from my Timecapsule. I have tried several times, and everytime I needed to reload reload etc. from Timecapsule. After my lateste reload Safari, Time Machine and System Settings are missing and are replaced by a "?" i the program bar!!! Help anybody!

Troubleshooting Network Problems Using Log and Trace Files

Hi,
can any one tell me how to generate trace and log files related to network errors.

start with inspecting listener.log
Post tailend (last 40 lines here) of listener.log

Networking Problems: Windows 7 and Tiger

Windows continues to suck.
I am trying to network a new Dell with Windows 7 to 10.4 and 10.5 Macs. It's trouble as always. For the Tiger machines, the Windows machine recognizes the computer and drives, but many of the files and folders are missing, including a large important one. There is no obvious way for it to refresh or update.
On the 10.4 machines on the network, the Windows machine recognizes the user folder, but none of the drives containing any of my files.
Besides throwing it out the window, any suggestions?

try a different USB cable and USB ports
"I'd rather be hated for who I am, than loved for who I am not." Kurt Cobain (1967-1994)

Updating problems for iTunes and system. both updates fail

does anyone know why when i try to update software it gets to cleaning up then stops and says there were errors but won't say what they were. i am trying to install itunes7 that wouldn't work so tried a system update and same thing nothing is working

is anyone else out there? are you seeing same issues? please help

[SOLVED]MSI P31 Neo -mobo and strange network problems

I can't get network to work properly with this MSI-mobo's integrated lan chip.
When I boot from Arch install cd r8169-module is loaded and I can get ip via dhcp. Strange thing is that I can access http but not ftp. When I change transfermode to passive from links ftp works. But during Arch install setup I can't access the repos.
When I boot to Arch after install network doesn't work at all. Only thing I get is resolv-errors when I try to use wget or pacman. R8169 module is loaded at boot and Ifconfig shows that I have ip assigned to eth0.
I also tried with 3com's 3c509 network card that I had laying around and I have exactly same network problems with it as I have with r8169.
I am really going out of my mind with this. I have a laptop with via's network chip and I've never had any network problems with it and Arch. I haven't changed anything in my routers setup and I just tried and the networking on my laptop works just fine.
I also tried Ubuntu Hardy on this desktop machine and networking works ok. Ubuntu also loads the r8169 module as Arch does.
Last edited by Aakko (2008-05-18 21:18:29)

Quote from: techie5487 on 24-January-08, 07:34:41
UPDATE:
I tried booting with 2 RAM Chips and it works great! This seemed to be the problem.
The ram IS double sided which would explain it.
If you are wanting some more system specs, just ask and I will try and get the most I can.
Del UK:
If I could run 4gb it would be great but I cannot seem to find the SPD in bios. My BIOS is American Megatrends Inc. v02.61 so it would be great if you could help me with that!
If all else fails I might either just settle with 2GB or buy some new RAM chips. Can anyone please tell me some Ram chips which would be able to give this mobo 4GB?
Thanks
techie5487
Done
2 Gb in
Into bios
SPD off
Set to 5-5-5-15
Save settings
Power off
Install extra 2 x 1Gb modules into slots 2 & 4
Power system up
4Gb detected................. slow post not fast
3.25Gb checked
1 second delay
4096Mb
3.25Gb extend
768Mb in +4Gb
System sees 3.25Gb

Migration Assistant Network Problem ?

I have been running Migration Assistant for about 2 days now using firewire from MacBook Pro to iMac Now it keeps coming up with "Might be problem with network" I have checked all passwords reset Router and Time Machine and both computers are able to communicate through them It now says about 12 hrs 33 min remaining and sticks at that but still "Might be problem with network" If I shutdown and reboot both computers will it start from where it left off or at the beginning again? Help please !!

RickAu wrote:
The iMac just stays saying "waiting for other Mac to restart". I have checked all connections re-set router and Time Capsule Made sure that all passwords are correct re-booted both computers.
This setup should just be using a Firewire cable connected between the two Macs, with the iMac running Migration Assistant & the other Mac in FireWire target disk mode. Networking connections & devices like Airport, Time Capsule, routers, etc. should have nothing to do with it.
For this setup, make sure you choose the Migration Assistant option to transfer data 'From a Time Machine backup or other disk' & not either of the options that mention a Mac on a network. Before you start Migration Assistant, put the other Mac in target mode & make sure it shows up in Finder.

Is Apple doing anything to fix the problem with displaylink in Mavericks?

I have been doing the Beta track for several years. Apple has been fairly good about ironing out the bugs before a release (as compared to Microsuck and other OS alternatives). But this problem with DisplayLink and Mavericks is about to kill me. I've been running multiple displays for several years and never had problems with prior OSX versions. My work computer (Macbook Pro) is still running Lion and works perfectly with DisplayLink and two 27" Samsung HD monitors. I would really love to get back to using the monitor setup with my Dev environment, however I can't even get a 2013 model Mavericks Macbook Pro to recognize that the DisplayLink device (IBM USB3.0 dock) is connected.
Once or twice I've gotten one monitor to show up after using the computer for a random amount of time. On that occasion, suddenly the main screen blinked and the second monitor came to life. I was reading webmail with Safari at the time and no other apps were running or had been started when it happened. This sort of thing isn't what I would classify as release-ready.
Every seed announcement I keep hoping for a fix, but after 3 since the Mav release, I'm beginning to lose hope. Anyone have info on how this might be made to work?
Thanks
David

DisplayLink also points fingers at Apple, which may be completely valid, but expecting Apple to put much effort into problems that only affect third-party hardware using an unsupported interface seems a bit of wishful thinking.
However, rumor sites indicate a focus on graphics in the next update : http://www.macrumors.com/2014/03/06/apple-seeds-first-os-x-10-9-3-build-to-devel opers/

Help with Boot Camp Assistant network problem while downloading windows support system!

I need to download Windows support software, but just keep encountering a problem which says "Can't download Windows Support Software because of a network problem." What should I do? I'm currently using Boot Camp Assistant v5.0.0, and OS X 10.8.2. Help! What can I do to solve this network problem? Please and thank you (:

I have the same problem. Anyone out there? Hello?

Why is there always network problem in bootcamp for me?

whenever i try downloading apple drivers from bootcamp i always have a network problem in between and i also to now from my friend tht it is just 700 mb but it takes very long fr me. May i please know the cause for this?
thnx

You should vist the Bootcamp forum where your question has been asked and answered many times. https://discussions.apple.com/community/windows_software/boot_camp

My imac intel display is frozen. Both the mouse and my network is working. Has anyone had problems like this and were you successful at fixing it?

My imac (Intel) display is frozen. Both the mouse and the network are working. I've shut down various times, pulled the cord from the receptacle on the power strip, and restarted several times. No luck. Has anyone had problems like this and were you successful at fixing it? Thanks. Would appreciate any help. Paula

Same problem, but a c.2009 iMac running OS X 10.9.1. Just happened overnight. Presently, I'm able to access my HD via wireless via laptop and copying all non-backed up files to an external drive. So far, Paula is the only other person I've found with this same problem and hers was three years ago! Going to keep searching for an answer.

Network problems 10.8 and mavericks both

Similar Messages

Maybe you are looking for