Network signal strength drops radically when i connect my comp to my displa

Hi
I have full network signal strength on my mac book pro, then when i connect to my cinama display the signal strength drops by over 75% , why would it do this ?

Are you using a static IP addressing on the phone?

Similar Messages

I updated to IOS 5 and now my signal strength drops sometimes clear to zero when I open an app.

I updated my Iphone 4 with the IOS 5 operating system. When I use an application, including the phone app, my signal strength bars will drop from 4 or 5 bars to 1 bar and sometimes to no bars and searching for a signal. When I exit the app the bars return tto what they were before. I have an AT&T plan that operates in Mexico which is where I am now. In Mexico it operates on the TelCell network. Before updating the op system I had no problems with the signal strength dropping when I used an app.

Hello timfromharris,
Have you gone to your date and time settings and verified that "set automatically" has been checked?
If you don't know where to go, it's Settings -> General -> Date and Time.
Good luck!
Brendon

E3200 - signal strength dropped

I'm a longtime fan of Linksys equipment. But my last 2 Linksys routers have been terrible. This one worked great for about 3 weeks then the signal strength dropped so low that you have to be within 10 feet of it to connect most of the time. The signal strength is unstable and will disconnect you in the middle of important downloads. I wasn't able to get into the setup last week and ended up rebuilding it using the software. Today I am unable to get into the setup again. I don't have time to dink around with it and am on my way to the store to buy a different brand. NO MORE CISCO/LINKSYS FOR ME!

Before I suggest you any troubleshooting steps, I would like to ask few questions. Let me know the light status on the router? What is the current IP address on the computer? How frequently does it happen?
All the E series routers come with the great Cisco connect software for the easy installation. Before installing the router, make sure that your Internet is working properly through the modem. Connect your computer directly to the modem and try to go on line.
If you are able to access the Internet from the modem, then your Internet is working properly. Now insert the CD in to the same computer. Do not run the CD on any other computer. Use the same computer that you used to connect to the modem. Follow the steps of the CD. It may not ask you to connect the computer to the router. But it is recommended that you should connect your computer to the router for the initial set up of the router. You will need to connect the computer to one of the Ethernet port on the router and the modem to the Internet port on the router. That means there will be 2 connections to the router. Now go to the next step on the set up CD. It will take up to 5 minutes to set up the router. Definitely you can setup the router without CD also. You just need to open the setup page of the router and change the settings manually.
Here is the link for setting up the Router through Cisco Connect: http://www6.nohold.net/Cisco2/ukp.aspx?pid=93&login=1&vw=1&app=search&articleid=22732&userrole=Links...
Second, there are many reasons why you experience poor signal or connection. Well, there are few things you should keep in mind with regards to N routers:
1) For the best possible speeds, you need to be using WPA2-AES as your security mode. Any other security mode will see your speed/range capped.
2) Ensure that your router is running the latest firmware from homesupport.cisco.com The new firmware includes performance enhancements and fixes.
3) The router by default uses a channel setting of auto, which means that it would keep switching channels depending on the interference. I’d recommend you set it to a fixed channel. Usually, 1, 3, 6 and 9 give you the best performance depending on your environment of course. I’d suggest you try different channels, observing each for a while, to see which gives you the best performance. You can follow the link here on how to change channels.
Second, please verify that you have got a 802.11n card in your computer. New generation routers (i.e. E4200) speaks an entirely different language with 802.11g cards, so while those adapters can work with the E4200, but they are not optimized to provide good performance. It is like having to translate from one language to another in real time when going from N to G.

When i back up an iphone on itunes does it save my social network passwords and stuff so when i connect another phone and sync it it'll all be there and i won't have to sign into everything again?

when i back up an iphone on itunes does it save my social network passwords and stuff so when i connect another phone and sync it it'll all be there and i won't have to sign into everything again? because, i don't know most of my passwords im just signed in to everything on my phone but i'm getting a new one.
please help

Hey menaelraghy,
Thanks for the question. The following resource outlines what is backed up, you may be interested in this section:
iTunes: About iOS backups
http://support.apple.com/kb/HT4946
- Keychain (includes email account passwords, Wi-Fi passwords, and passwords you enter into websites and some applications)
If you encrypt the backup, you can transfer the keychain information to the new device. With an unencrypted backup, you can restore the keychain only to the same iOS device. If you're restoring to a new device with an unencrypted backup, you need to enter these passwords again.
Thanks,
Matt M.

Signal strength dropping.

Over a period of some 12 hours wireless signal strength drops from 15 to 5. On restart it goes back to 15. What is causing this please?

B16JOP-
That is a very good question. If your problem were caused by some external interference I would not expect it to come right back.
This Airport troubleshooting guide may be of some help.
Luck-
-DaddyPaycheck

TS1398 my problem is my iphone 4s is connected to the internet(wi-fi) with full signal strength but freezes when browsing and says "Cannot Open Page, Safari could not open page because the server stopped responding".

my problem is my iphone 4s is connected to wi-fi with full signal(3 bars) strength but freezes when browsing and says
"Cannot Open Page"
"Safari could not open page because the server stopped responding"
I already reset the iphone to its factory settings and erase all contents but still the browsing speed freezes or not searching at all. Sometimes it will work and fast but then the problem uccors every now and then. Iv'e been using iphone 4 for two years and I still have it and works fine compared to this IPHONE 4S.

Settings → scroll down to Safari → in Safari settings, I selected both Clear History and Clear Cookies and Data.
IF that does not work -
Restart or reset your iPhone, iPad, or iPod touch - Apple Support
Finally - if problem still present -
Go to Settings>General>Reset
Reset the network settings - you will need to add the password of your home WiFi in your phone once more
The device should turn itself off & back on then go into Settings>Wifi and join your network

Bandwidth usage/signal strength/dropped signal WRT160nv2

Three questions
1. How can I determine how much bandwidth each of my network devices are using. Is there anyway to tell using Linksys easylink which is installed on my machine? I have a WRT160nv2 router.
2. Is there anyway to boost signal strength through internal settings. If so, how do I do that.
3. Been experiencing dropped signal for some wireless devices. Is there any way to determine why this happens and is there a fix for this problem.
thanks

1. Sorry no.
2. Sorry no.
3. Change these settings in the router. Disable UPnP, under wireless settings Beacon Interval 50, RTS and Fragmentation threshold 2304. Change to channel 1. Save settings. Reconnect.

Weak network signal strength

I don't receive 3G network signal at all on ma phone, and the 2G signal is barely available but am in a full strong network coverage area. Don't know what it could be that's wrong with my phone.... Help please

Hello alphaabet and welcome to the BlackBerry® Support Community Forums.
Sorry to hear you are having network issues with your BlackBerry® Curve™ 9360 smartphone.
Did you buy this device directly from your mobile carrier or was it purchased unlocked from another source?
Network coverage is carrier determined so if you did buy this device from another branded carrier that didn't support 3G then when it wouldn't access 3G, even unlocked with another mobile carrier.
If you did purchase this from your mobile carrier and are still unable to acquire 3G then call your carrier and asked to be transferred to RIM® support for further investigation.
Hope this answers your question.
VIA | hmthepirate
http://supportforums.blackberry.com/t5/BlackBerry-Curve/9380-unable-to-get-3g/td-p/1748391
Hi and Welcome to the Community!!
I suggest the following steps, in order, even if they seem redundant to what you have already tried (steps 1 and 2 each should result in a message coming to your BB...please wait for that before proceeding to the next step):
1) Register HRT
KB00510 How to register a BlackBerry smartphone with the wireless network
Please wait for one "registration" message to arrive to your Messages app
2) Resend Service Books
KB02830 Send the service books for the BlackBerry Internet Service
Please wait for "Activation" Messages, one per already configured email account, to arrive in your Messages. If you have no already configured email accounts, please wait 1 hour.
3) Batt Pull Reboot
Anytime random strange behavior or sluggishness creeps in, the first thing to do is a battery pop reboot. With power ON, remove the back cover and pull out the battery. Wait about a minute then replace the battery and cover. Power up and wait patiently through the long reboot -- ~5 minutes. See if things have returned to good operation. Like all computing devices, BB's suffer from memory leaks and such...with a hard reboot being the best cure.
Hopefully that will get things going again for you! If not, then you should contact your mobile service provider for formal support.
Good luck!
VIA | sdgardne
http://supportforums.blackberry.com/t5/BlackBerry-Curve/9380-unable-to-get-3g/td-p/1748391
I found this problem happening with release 7.1.0.523 (or 569) on the all BlackBerry models. Try upgrading to 7.1.746, the current release for the 9320. Although this update is for a different carrier, there's an easy way around that, see this page for links and instructions:
http://crackberry.com/official-os-710746-now-available-blackberry-curve-9320-and-9220-xl-indonesia
* BONUS: This update adds the ability to customize the LED colours for incoming calls, and texts, and other notifications. *
VIA | xe77
http://supportforums.blackberry.com/t5/BlackBerry-Curve/BB-logo-next-to-my-3G-coverage-keeps-on-disa...
Under the Mobile Network settings you might have set the Network mode on "2G" while you should have it on "3G and 2G" (or only 3G, but that's not as stable). Do you know what I mean?
VIA | habbitzz
http://supportforums.blackberry.com/t5/BlackBerry-Bold/My-Blackberry-Bold-9790-not-getting-3G-networ...
Please thank those who help you by clicking the button.
If your issue has been solved, please resolve it by marking "Accept as Solution"

How can we access network signal strength of pocket PC in java 1.1.8?

can anyone tell me if there is any way i can access the signal strength of a wireless access point by a java program for a pocket PC (Compaq iPaq)?
the iPaq only supports java 1.1.8

Hello,
I'm a french student and I have exactly the same problem as you.
It has been 3 weeks I'm searching, but I have not results.
Today, do you have the solution????? If yes, can you tell me something about that??
Thank you very much!!!
Yohan
can anyone tell me if there is any way i can access
the signal strength of a wireless access point by a
java program for a pocket PC (Compaq iPaq)?
the iPaq only supports java 1.1.8

How come my signal strength dropped after 5.1.1 upgrade?

I downloaded ios 5.1.1 to my iphone 3gs,now i am experiencing problems with my signal strength,slower internet speed,and wifi cuts out,have to manually access through general settings.What is causing this and how do I solve it?

See my FAQ*:
http://www.macmaps.com/WIFI1048.html
Check that your clock battery isn't nearing death.
- * Links to my pages may give me compensation.

Difference in signal strength (Edge nwrk) when 2 iPhones are next to each o

other...
My girlfriend and I each have an iPhone (purchased beginning of December, 09).
I have the 3Gs, and she has the 3G.
On a LOT of occasions, and I can hold the iPhones in each hand and use them identically. The only difference is that she (3G phone) stay's at full strength, and mine (3Gs) wanders from 1 bar to full strength.
If I leave mine alone for a minute, it'll start to creep back towards full strength. However, as soon as I start using it, it'll knock it down a bar or two.
We were in a different city, other than our home, for Christmas (hadn't used the iPhones there yet) and she sat there with full strength, and mine kept going from 1 - 3 bars.
I don't know what's going on, and it's driving me crazy. I can use them the same way, and they can act totally differently (signal strength-wise).
I have done a reset (power and home button) and that hasn't helped at all.
Is this something that I should take to the store and ask them to figure out what the heck is going on?
Thanks!

Well since they are both iphones it helps. What i would personally do is:
1) Take her sim card out of her iphone and put it in yours and see if you get the same signal strength you did with yours in or if you get full signal like her 3G.
a) If you get the same signal there (1-3 bars) it may be a issue with your iphone software/hardware. (Try restoring and setting up as a new device.)
b) If you get full signal like she did in her 3G then it most likely is the sim card that you have.
You can also test your sim card in her iphone. Same difference as what I explained but backwards. Either way it will tell you if its the sim card or the iphone.
If you put yours in her iphone and get the 1-3 bars get a new sim card. If you get better signal restore and setup as new and test. If it still occurs it may be something with the iphone itself.
Hope this helps!!

Signal keeps dropping out when "waking up" from sleep state

When I reboot or reset my network settings,my Iphone 6 gets 5 bars with 3G (with 4g disabled or enabled).But when I LOCK THE PHONE and wait for maybe 1 minute and unlock it, the signal drops to 1 bar, search network and restore to 5 bars.It happens every time I lock the Iphone! I tried already restoring (IOS 8.1.3) and upgrading to 8.2, switching off and resetting network data. Nothing works, I look like it stays in a "low power mode", and when it wakes up the internet come back after searching for the network...I can not use internet immediatly. And this is happening when I am using it too! When I lock the phone, my nightmare start, with the network disconnecting and connecting,

Hi,
I am coming from the MacBook faction, but there were similar posts in there, regarding at least your picture#2, the vertical colored lines.
The consensus was (and I cannot write from own experience here, just relaying the message) that this has something to do with system parameters. To rewrite these parameters, one has to set a different screen resolution than the current one and save the settings and then go back to the old resolution again and save the settings as well. We were told, this would prevent the colored vertical line issue, at least for the MacBook.
Worth a try, it is easy enough to do.
Regards,
Woelund

How can I set up my time capsule as the primary base station with a centurylink router? I'm trying to extend my coverage, increase signal strength, and be able to connect a printer.

I recently moved and now I'm trying to set up my Time Capsule as the primary base station or router with an existing network that has a Centurylink modem/router. The TC still has the settings for my old network. I also have backups on it. I have the data backed up to another HD so it's not an issue to return it to factory settings if doing so deletes the back ups. Do I need to restore it to the factory settings to set it up? Also, what settings would I select on the TC (and the Centurylink modem/router) in order for the TC to serve as the router, instead of the Centurylink router? I want to be able to use the TC to back up my Mac's, print wirelessly, and improve overall performance. I tried setting the TC up and ended with 2 different networks. Can anyone please help me with this?

The TC has to plug into the existing modem router by ethernet.. you cannot use wireless.
You have a choice of which is router.. only if Centurylink agree to bridge their modem router.. this has to be done by the ISP and often they do not allow it.
Is your broadband cable or adsl or fibre or ???
If it is cable and you are allowed to purchase your own cable modem pick a pure modem version with no router in it.. plug the TC into it by ethernet.
Setup the TC in DHCP and NAT mode.. (depending on broadband type).
You must reset the TC to factory to do the setup.. no files are lost at all.
Here is my current recommended setup.. with Yosemite life has become harder than ever.
Factory reset universal
Power off the TC.. ie pull the power cord or power off at the wall.. wait 10sec.. hold in the reset button.. be gentle.. power on again still holding in reset.. and keep holding it in for another 10sec. You may need some help as it is hard to both hold in reset and apply power. It will show success by rapidly blinking the front led. Release the reset.. and wait a couple of min for the TC to reset and come back with factory settings. If the front LED doesn’t blink rapidly you missed it and simply try again. The reset is fairly fragile in these.. press it so you feel it just click and no more.. I have seen people bend the lever or even break it. I use a toothpick as tool.
N.B. None of your files on the hard disk of the TC are deleted.. this simply clears out the router settings of the TC.
Setup the TC again.
ie Start from a factory reset. No files are lost on the hard disk doing this.
Then redo the setup from the computer with Yosemite.
1. Use very short names.. NOT APPLE RECOMMENDED names. No spaces and pure alphanumerics.
eg TCgen5 and TCwifi for basestation and wireless respectively.
Even better if the issue is more wireless use TC24ghz and TC5ghz with fixed channels as this also seems to help stop the nonsense. But this can be tried in the second round.
2. Use all passwords that also comply but can be a bit longer. ie 8-20 characters mixed case and numbers.. no non-alphanumerics.
3. Ensure the TC always takes the same IP address.. you will need to do this on the main router using dhcp reservation.. or a bit more complex setup using static IP in the TC. But this is important.. having IP drift all over the place when Yosemite cannot remember its own name for 5 min after a reboot makes for poor networking. If the TC is main router it will not be an issue.
4. Check your share name on the computer is not changing.. make sure it also complies with the above.. short no spaces and pure alphanumeric.. but this change will mess up your TM backup.. so be prepared to do a new full backup. Sorry.. keep this one for second round if you want to avoid a new backup.
5. Mount the TC disk in the computer manually.
In Finder, Go, Connect to server from the top menu,
Type in SMB://192.168.0.254 (or whatever the TC ip is which you have now made static. As a router by default it is 10.0.1.1 and I encourage people to stick with that unless you know what you are doing).
You can use name.. SMB://TCgen5.local where you replace TCgen5 with your TC name.. local is the default domain of the TC and doesn't change.
However names are not so easy as IP address.. nor as reliable. At least not in Yosemite they aren't. The domain can also be an issue if you are not plugged or wireless directly to the TC.
6. Make sure IPv6 is set to link-local only in the computer. For example wireless open the network preferences, wireless and advanced / TCP/IP.. and fix the IPv6. to link-local only.
There is a lot more jiggery pokery you can try but the above is a good start.. if you find it still unreliable.. don't be surprised.
You might need to do some more work on the laptop itself. eg Reset the PRAM.. has helped some people. Clean install of the OS is also helpful if you upgrade installed.
Tell us how you go.
Someone posted a solution.. See this thread.
Macbook can't find Time Capsule anymore
Start from the bottom and work up.. I have a list of good network practice changes but I have avoided Yosemites bug heaven.
This user has had success and a few others as well.
RáNdÓm GéÉzÁ
Here is why Yosemite has fundamental issues.
http://arstechnica.com/apple/2015/01/why-dns-in-os-x-10-10-is-broken-and-what-yo u-can-do-to-fix-it/

Dropping signal strength

hello,
recently I have changed from an AirPort basestation to an Airport Extreme basesation.
There are two iBooks (G3 and G4) and a PowerBook G4 using the wireless LAN.
Having now installed the latest (driver) software from Apple my iBook G4 (running on Panther) has four bars signal strength when booting or waking up. But within 20 to 30 seconds the signal strength drops to only two bars in the menu list.
This is strange to me because the PowerBook G4 (running on Tiger) has always four bars even if they are on the same table about 4 meters from the AirPort basestation away. Usually the PowerBook is further away and still has its four bars.
With my old AirPort both computers had always four bars.
Where shall I start searching to solve this?
If the signal drops even to one bar then sometimes the connection to the Internet is very poor (eg I had to click a hyperlink twice to get the page or I will run into a network timeout).
thanks for your help
ueli
iBook G4 Mac OS X (10.3.9)

the problem is solved, it had nothing to do with the change of the AirPort base stations. The iBook G4 had a broken antenna cable.

Finally connected but no boost in signal strength on WRE54G

It took a while but I finally got the WRE54G v 3.04.01 to connect to my network. I have a WRT54Gs Router v2.07.1 Both blue lights are now on and it seems to be connected and working but I don't have any increase in signal strength. I matched the SSID (broadcasting) the channel and WEP key settings. When I go over to our addition my signal strength drops to 1 or 2 bars and from 54g to 11g as indicated on my laptop. If I then connect the repeater right next to my laptop there is no signal improvement or change in anyway. I disabled my connection and re-enabled it without any improvement either. Could it be a setting on the router or maybe it needs a firmware update? I saw on the web site that it met the minimum version at 2.07. can you please advise what i might try to increase the signal strength. thanks.k

Well I made some progress with my problem today. I'm not sure if it was a couple small changes I made on my router or just another day and a rebooting of the PC's but either way today Id downloaded a wifi signal troubleshooter called inSSIDer which let me look at both signals from the router and the expander and see what they were doing. eventually I got them placed to where I seem to have relatively equal signal strength from my basement to the upstairs of the new addition. More of less as I walk the paths but once I'm there it's not bad. I get excellent strength and connectivity so I'm not complaining yet.
My only remaining concern is if I should upgrade the firmware on my WRT54GS router or not. it's at 2.071. which meets the minimum required to connect with the WTR54GS expander or so I read, but this router doesn't have the back up restore function on this version so I am not eager to have to completely set this thing back up again after an upgrade. Won't that reset everything back to defaults? Or does anybody here know if it saves my configurations? Somehow I doubt that it would but ya never know.

Network signal strength drops radically when i connect my comp to my displa

Similar Messages

Maybe you are looking for