Networked L7680 does not work from more than one computer at a time.

Have installed latest driver software on both computers. Printer will only work with one computer on at a time. When I run windows device trouble shooter from the last computer turned on it says printer is off. It works ok from the first computer turned on.
Any help is appreciated.

Networked how?? Please explain how everything is connected and model number of equipment.
Say thanks by clicking the Kudos Thumbs Up to the right in the post.
If my post resolved your problem, please mark it as an Accepted Solution ...
I worked for HP but now I'm retired!

Similar Messages

WRT54GX4 Router Will Not Connect to More Than One Computer at a Time Wireless

I have a WRT54GX4 and cannot connect wirelessly with more than one laptop at a time. Each laptop I have will connect if I disconnect the other one. I have upgraded to 1.00.20 firmware and tried to find a setting for the router to address the problem without success.

double check on the mac addresses that you have saved so that your wireless computers can connect properly to your netwok, or you could just disable the mac filtering so that all of your computers can easily connect, just secure your wireless network

E3200 - USB port does NOT work for more than one device

We needed a new router that had the dual band connectivity as our previous router stopped working properly when we started using a baby monitor operating on the same 2.4 GHz. The choice was between E3200 and E2500. We chose the E3200 mainly because it also offered a USB port. We were hoping to use that to connect our printer and two external drives (thus bypassing our old desktop that's been working as a server). However, it turns out that the USB port on E3200 does NOT support USB hubs! So, you can ONLY use ONE device - either a printer or one external storage drive. That wasn't really clear at all from the description. I feel like we wasted the extra $50 hoping to get functionality that just isn't there. Can't believe that in this day and age, Cisco thinks we all have only ONE USB device we might want to connect to the network! The router itself is fast enough, but the extra $50 for a USB port that doesn't do much and some speedboost phantom ability is just not worth it.

Just to save time to you all, after numerous attempts to install a USB hub to my E3200,
I wrote to Cisco Customer Service (live chat) and I specifically requested how to set up the usb hub or the virtual USB port and they said that they do not have a software to install a USB hub.
Hope this help
Massimo
(Mod note: Edited for guideline compliance.)

Tcode MASS does not work if more than one item in contract

Hi,
I need to update the contract zone of a PO. Via tcode ME22N, this zone is disabled, so i cannot fill my contract in the PO using this tcode.
I tried tcode MASS which works only if the contract has only one item.
Can anyone help please?
Thanks in advance

HI Anu,
Good to KNow that you are able to do it by Mass
In Mass for Multiple Line Item to update to Multiple line item PO
Just go to MASS
Select the option BUS2012 (Purchase orders)
and in the select the poline item EKPO
And enter the PO Number along with the Item Number in the entry screen and execute it .
But for the Contract also enter the option
Outline Agreement -- for the contract number
Principal Agmt Item-- for the contract item number
Enter the above against the PO and its item number combination it works.
As suggested earlier please check the Screen layout option also.which would be more easy way,
Check the PO Screen layout-Field settings. at the Document type level mainatained in the config.
against the
Hope so this would help.
Regards
Anjanna

Can not color label more than one file at a time

Hi,
I've had this problem since 10.6.6-ish, i can not color label more than one file at a time in the Finder.
Wether i select two, twenty or twohundred only one file gets color labeled.
It doesn't seem to matter if i assign a color label through the File menu or right click > label.
Figured a re-install might fix this but it hasn't (even a clean install without restoring any kind of backup).
Does anyone else have this issue and/or a fix for it?
Thanks,
Jay

Aaaaanyone ?

Opening hotmail: Please refresh your browser window, When you access your Windows Live Hotmail account from more than one computer, we ask you to sign in again to help keep your account private and secure . Refreshed but no change. in Safari no problem

opening hotmail in firefox: Please refresh your browser window, When you access your Windows Live Hotmail account from more than one computer, we ask you to sign in again to help keep your account private and secure . Refreshed but no change. in Safari no problem

Go to '''Options '''on Firefox Browser-->'''Advanced'''-->''Click on'' '''Network '''tab-->''Select '''''Settings'''-->''Select '''''Use System Proxy Settings
'''

File open on more than one computer at a time

I maintain a network of four Macs (Cube, G4 Tower, Mini, and G5 Tower) all running OS 10.4.11. Recently two people working on the network discovered that they both had a certain file open at the same time. In order to determine the extent of the problem, on each computer I created and kept open a TextEdit file. I then attempted to open each TextEdit file from the three computers on which the file was not stored. To my dismay I received no error or warning message of any sort. I was able to open all four files on all four computers at the same time!
Each of the computers has a single user, and each computer is logged into the other computers as the user on that computer (i.e., each guest is logged in as the host). I wonder if that might be the source of the trouble.
I never noticed any file being open on more than one computer at a time when all the computers were running 10.3.9, only after I upgraded to 10.4.
Any ideas?

This is absolutely standard behavior and I don't expect this to change any time soon.
Let me try to explain based on a model of a file stored on Server1 and being accessed by Client1 and Client2:
Here's what's happening:
Client1 connects to the server and opens the file for reading.
Client1 reads the file and closes it
Client2 connects to the server and opens the file for reading.
Client2 reads the file and closes it
Since Client1 closed the file there's nothing to indicate to Client2 that the document is in use anywhere else because, in fact, it isn't.
There's nothing on the server that knows whether Client1 opened the file to look at it, to copy it, to back it up to some other media or to actually edit it. It is only that last step that should prevent another client from opening the file.
If you think about it, that makes perfect sense. If you copy the file over the network to Client1 you do not want the server to think that Client1 has an exclusive hold on that file and to prevent Client2 from opening it.
The only time the file is in use is a) when the file is being read, and b) when the file is being saved. When it's just being viewed the client doesn't have an active hold on the file.
The actual fix here is for the application to set a flag that the file is in use and for the server to honor that flag. It's supported by the networking protocols but it's rarely implemented in applications except those that expect a multi-user setup.

Connect more than one computer to a time capsule volume?

Hello. I am considering buying an old time capsule (500G, 2nd generation) as a little in-house server to store data that need to be accessible for more than one work station. Is it possible to connect more than one work station to one time capsule?
Thanks

While it is possible to connect more than one computer to the Time Capsule......I would not recommend that you buy the Time Capsule that you are looking at.....unless you know that the owner has replaced the hard drive and power supply.
Most of these models never made it much past a few years of operation, so if this is an "original", you have a hint of what will happen not long after you purchase the product.

How can I synchronize safely from more than one computer?

First, I have set up my iPod to work with two computers: my primary computer, which is my desktop at home. Later, I also "authorized" my laptop (as a secondary source) to also be able sync to my iPod.
My question is that when I go to synchronize some podcasts I just downloaded to my secondary computer (my laptop), I get the following prompt: "Are you sure you want to sync podcasts? All existing podcsts on the iPod '<my iPod's name>' will be replaced with podcasts from your iTunes library."
From this message, since my iPod is plugged into my laptop, I assume it's referring to my iTunes library on my laptop (which only has the few podcasts I just downloaded). And it sounds like it's going to delete the podcasts that are already on my iPod.
I definitely don't want it to "replace" the ones I already have sync'd from my home computer; +_I just want to add the ones I have downloaded to my laptop._+ How can I make it so I can safely add the new ones without disturbing those I already have sync'd and want to keep? I'm a bit confused about how syncing works when you have more than one computer to sync to the iPod.

You cannot do what you want.
The ipod touch can sync with ONE computer/library at a time.
When you sync to a different computer/library, the ipod touch will first delete the current itunes content form the iphone, then it will sync the content from the new computer.
This is the way it is designed.

Manage music and videos manually from more than one computer

Hello,
I'm triying to transfer music from two computers (work computer and home computer) to my iPhone. The problem is that when I select the Manage music and videos manually on my iTunes and then apply it keep saying that the iPhone is already synchronized with another computer and if I accept I lose all the media (video and music) on my iPhone. I just want to add new videos and new music manually without losing the existing ones, is it possible?.
I'm using the iPhone 3G with iTunes 7.7 (last version) and Windows Vista.
Thank you

Then it is not possible to add new music files or video files to my iPhone from more that one computer without losing the ones I already transfered from another computer. This is a pitty
Thank you very much

Apex 4.0 tree does not work with more than 2 levels.

When I have more than 2 levels in my tree, I only see the root node. The query works fine and returns 132 rows when I run it in SQL. It is just the tree that does not work.
The same tree when built in 3.2 works fine.
This is my tree query:
select case when connect_by_isleaf = 1 then 0
when level = 1 then 1
else -1
end as status,
level,
"NAME" as title,
null as icon,
"ID" as value,
null as tooltip,
null as link
from (
SELECT '__TOP_NODE__' id
, NULL pid
, 'BI Applications' name
, '' link_id
, null a1
     , null a2
FROM dual
1 b) BIA Modules
UNION ALL
SELECT '__MD_'||module_key id
, '__TOP_NODE__' pid
, module_name name
, module_key link_id
, '__MD__' a1
     , null a2
FROM c_bia_module
Level = 2
Parent = Module
Node = Functional Areas
ID = '__FA_' prefixing functional area code
UNION ALL
SELECT '__FA_'||funcarea_key id
, '__MD_'||module_key pid
, funcarea_name name
, funcarea_key link_id
, '__FA__' a1
     , null a2
FROM c_functional_area
Level = 3
Parent = Functional Area
Node = Fact Group
ID = '__FG_' prefixing fact group key
UNION ALL
SELECT '__FG_'||factgroup_key id
, '__FA_'||funcarea_key pid
, factgroup_name name
, factgroup_key link_id
, '__FG__' a1
     , null a2
FROM c_fact_group
start with "PID" is null
connect by prior "ID" = "PID"
order siblings by "NAME"
If I reduce the query to just use two levels like:
SELECT '__TOP_NODE__' id
, NULL pid
, 'BI Applications' name
, '' link_id
, null a1
     , null a2
FROM dual
1 b) BIA Modules
UNION ALL
SELECT '__MD_'||module_key id
, '__TOP_NODE__' pid
, module_name name
, module_key link_id
, '__MD__' a1
     , null a2
FROM c_bia_module
It works fine. Can somebody let me know what I am doing wrong? Is there a way to set the number of levels supported in 4.0?

Hi Vidya,
Thanks for posting your example. You may want to remove your workspace details from the previous posting, or at least update the password on the workspace. I've taken a look at your example and initially couldn't see anything wrong with your tree query. However, when I ran your query in SQL Workshop, it only returned one row, which would explain why you were only seeing one node in your tree! I've updated your query to use a WITH clause, and the tree is now working correctly. I believe you've hit an underlying database bug where the CONNECT BY query is only returning 1 row, when in fact it should return > 1 row. By re-writing the query to use a WITH clause, you can get around the problem.
Regards,
Hilary

How do i print from more than one computer?

How do I set up my HP 4500 Envy printer to print by wireless for more than one laptop user?

Hi @MHorton,
Welcome to the HP Forums!
I understand that you are wondering how to set up your HP 4500 Envy printer to print by wireless for more than one laptop user.
In short, you will need to install the full feature software and drivers for each laptop, and make sure they are connected to the same wireless network as the printer.
Please see this guide, Installing the Printer Software for a Wireless Network Connection, for further assistance.
If you do not know the Operating System you are using, please visit this website. Whatsmyos.
Hope this information helps, please let me know if you have any other questions!
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping!

Is it possible to add musc from more than one computer like on ipods?

is it possible to add music from more than computer like with ipods

No. The iPhone will synch with only ONE iTunes library at a time.

The ff default theme keeps re-enabling itself after computer restart even though I enable littlefox and restart firefox, and it does the same on more than one computer. I want littlefox to start with firefox, not have to enable every time.

I want littlefox to start with firefox, not have to enable every time the computer starts.

@kalos
Uninstalled everything PA, also uninstalled mangler which was the only thing that depended on PA. It didn't work anyway.
No pulseaudio --kill command so I couldn't run.
Checked systemd journal and there is no mention of PA this time.
Checked top, and grepped ps aux and there is no PA there either.
I also rebooted the machine completely just to make sure. However VLC and HTML5 have the same incompatibilities.
_ vlc Videos/anime/fmab/01.mp4
VLC media player 2.1.5 Rincewind (revision 2.1.4-49-gdab6cb5)
[0x1bc30f8] pulse audio output error: PulseAudio server connection failure: Connection refused
[0x1af4118] main libvlc: Running vlc with the default interface. Use 'cvlc' to use vlc without interface.
Fontconfig warning: FcPattern object size does not accept value "0"
Fontconfig warning: FcPattern object size does not accept value "0"
Fontconfig warning: FcPattern object size does not accept value "0"
Fontconfig warning: FcPattern object size does not accept value "0"
[0x7fb604001248] main vout display error: Failed to resize display
But the video and audio did work until I ran some HTML5 video, after which the audio worked, and then I opened it again and it didn't work...
@nomorewindows
I see. That's too bad. At least we're not alone.
Last edited by Greduan (2014-11-14 01:34:29)

How to remove tooltips from more than one field at a time?

I use the wizard and now there are more than 2000 fields with useless tooltips on each of them. How do I remove all the tooltips at once?

Run this code from the JS console:
for (var i=0; i<this.numFields; i++) {
    var f = this.getField(this.getNthFieldName(i));
    if (f==null) continue;
    f.userName = "";

Networked L7680 does not work from more than one computer at a time.

Similar Messages

Maybe you are looking for