Networking troubles with ABIT BP6 board and Solaris 8

Hi, Im trying to install the Solaris 8 software on my ABIT BP6 board with a Compaq NetFlex3 10TX NIC. This is a SMP board (dual celeron) but is not on the HCL (the NIC is).
The installation gives no problems at all (except for a memory conflict between memory devices), and SunOS works pretty well except for networking... using ifconfig -a shows me the networking interface and the loopback interface but I can't ping outside of the Solaris machine (or ping to the Solaris machine from an other machine).
I know that the board is not on the HCL but I had no networking troubles with Solaris 8 early access.
After instalation of the software and the reboot, I get the status as below:
>
configuring IPv4 interfaces: cnft0.
Hostname: MILLIWAYS
Configuring /dev and /devices
Configuring the /dev directory (compatibility devices)
The system is coming up. Please wait.
checking ufs filesystems
/dev/rdsk/c0d0s7: is clean.
All devices are configured...
Configuring network interface addresses: cnft0.
RPC: Timed out
Starting IPv4 routing deamon.
starting rpc services: rpcbind done.
Setting netmask of cnft0 to 255.255.255.0
<
As you can see I get a time out while configuring the NIC. I tried a lot of different things (and some bad ones like using the device driver disk of the EA version with the cd's of the final version but no luck there...)
Anyone with the same problems or any help?
Thanx, Marcel

Hi maeck,
I'm sorry that my message is off the topic. Could you help me with a problem that I have with Abit BP6 + Solaris 8 combo?
I'm encountering error message on console screen during booting/reboot/shutting down like "APIC error interrupt on CPU 0. Status=2" where CPU can be 0 or 1, status can be 0, 2, 4 or 6.
If I let my dual Celeron400 run at 400MHz, the frequency of errors is few and far between. Though it still happens. If I overclock them to 558MHz like I udually do, it will show at least 4 times during a booting process. I've tried MPS 1.1 and 1.4 settings. I've also tried turning off all cache, delayed transaction, passive release settings.
In addition, the overclocked system tends to lock up while it runs flawless in Windows 2000 Professional and Redhat 6.1. Do you have any similar experience?
My system config:
Abit BP6 motherboard
400 MHz CPU X 2
GlobalWin FEP32 X 2
128M SDRAM
Creative Labs 3DBlaster TNT2
13GB Maxtor DiamondPlus 6800
Acer 10x DVD drive

Similar Messages

Having trouble with getting on messages and facetime

having trouble with getting on messages and facetime. Got two new ipods, one works fine, the other keeps giving us the error: iMessage Activation Could not sign in. Please check your network connection and try again. We have tried to reset the factory settings, and verified that the internet is working. Please help!

FaceTime, Game Center, Messages: Troubleshooting sign in issues

I am having trouble with the Jpeg icons and also now thumbnails not being visable in bith teh Apple finder and now also Adobe Bridge. Can anyone shed any light on this ?

I am having trouble with the Jpeg icons and also now thumbnails not being visable in bith teh Apple finder and now also Adobe Bridge. Can anyone shed any light on this ?

Argh - once again, I find my solution right after posting this. Left out one modification to the SWIG script, now it runs in 29 seconds vs C 16 seconds, I can live with that.

Trouble with iMovie '11 transitions and themes? I'm running Lion, Mac OS X and just noticed today that the transitions and themes don't seem to be working at all when I start new projects or try to add to old projects. What is the solve here?

Trouble with iMovie '11 transitions and themes? I'm running Lion, Mac OS X and just noticed today that the transitions and themes don't seem to be working at all when I start new projects or try to add to old projects. What is the solve here?
I've seen notes about clearing the cache but it seems that this is an older OS and I can't find the plist mentioned here because it's an older system. http://www.youtube.com/watch?v=2cL9RuDV3Qc
Thoughts? Anyone?

GUYS, I NEED HELP !
ANYONE?

I had a trouble with my lap top and had to format hard disk and install all soft ware again. could any body tell me how to transfer the application and data in my i phone back to my laptop.

I had a trouble with my lap top and had to format hard disk and install all soft ware again. could any body tell me how to transfer the application and data in my i phone back to itune.

You can't. It still thinks that your iPhone is synced with another iTunes library (the one that you had before you reformatted the hard drive.

Having trouble with pop-up windows and ads for MacKeeper

I've been having trouble with pop-up windows and ads for MacKeeper and similar "services." Tried to download "MPlayerX" a week ago and it all started then. I thought I deleted the file but I'm still having trouble. I've been digging for solutions on here, but nothing I've found on here has worked yet--the VSearch stuff (I think) isn't on my hard drive. Any advice?

You installed a variant of the "VSearch" trojan. Remove it as follows.
This malware has many variants. Anyone else finding this comment should not expect it to be applicable.
Back up all data before proceeding.
Triple-click anywhere in the line below on this page to select it:
/Library/LaunchAgents/com.venus.agent.plist
Right-click or control-click the line and select
          Services ▹ Reveal in Finder (or just Reveal)
from the contextual menu.* A folder should open with an item selected. Drag the selected item to the Trash. You may be prompted for your administrator login password.
Repeat with each of these lines:
/Library/LaunchDaemons/com.venus.daemon.plist
/Library/LaunchDaemons/com.venus.helper.plist
Restart the computer and empty the Trash. Then delete the following items in the same way:
/Library/Application Support/venus
/System/Library/Frameworks/v.framework
The problem may have started when you downloaded and ran an application called "MPlayerX." That's the name of a legitimate free movie player, but the name is also used fraudulently to distribute VSearch. If there is an item with that name in the Applications folder, delete it, and if you wish, replace it with the genuine article from mplayerx.org.
This trojan is often found on illegal websites that traffic in pirated content such as movies. If you, or anyone else who uses the computer, visit such sites and follow prompts to install software, you can expect more of the same, and worse, to follow. Never install any software that you downloaded from a bittorrent, or that was downloaded by someone else from an unknown source.
In the Security & Privacy pane of System Preferences, select the General tab. The radio button marked Anywhere should not be selected. If it is, click the lock icon to unlock the settings, then select one of the other buttons. After that, don't ignore a warning that you are about to run or install an application from an unknown developer.
Then, still in System Preferences, open the App Store or Software Update pane and check the box marked
          Install system data files and security updates (OS X 10.10 or later)
or
          Download updates automatically (OS X 10.9 or earlier)
if it's not already checked.
*If you don't see the contextual menu item, copy the selected text to the Clipboard by pressing the key combination command-C. In the Finder, select
          Go ▹ Go to Folder...
from the menu bar and paste into the box that opens by pressing command-V. You won't see what you pasted because a line break is included. Press return.

I'm having trouble with my sound up and sound down keys. They're doing other functions. This is only a new thing.

I'm having trouble with my 'sound up' and 'sound down' keys. They're doing other functions. This is only a relatively new thing.

You didn't mention what those "other functions" were. That might help!
First thing to check is System Preferences > Keyboard > Keyboard tab - make sure "Use all F1, F2, etc. keys as standard function keys" is un-checked. Hopefully that still works in Mountain Lion.

HT4623 Anyone having trouble with App Store install and cloud store buttons not working after 6.1 update?

Anyone having trouble with App Store install and cloud store buttons not working after 6.1 update? I go to install an app. I hit install and nothing happens. About a minute later it asks me for my password and then it does nothing. The install button goes back to saying install. However the app shows up in my installed list and in cloud but no app installed.

OK - I found a helpful post - closed app store app and under Settings/General/Date and Time I reset the date and time by switching off "Set Automatically" and then switching it on again. Went back to App Store, launched it and Updatesseems to be working again.
Go figure? Logical, No!

HT5621 I am having trouble with my Apple ID and AppStore Here are the steps I have taken and the results: 1. Changed my Apple ID with new email address. 2. Changed my iCloud with above new email address. 3. NOW - Apple ID appears correct in Ap

I am having trouble with my Apple ID and AppStore
Here are the steps I have taken and the results:
Changed my Apple ID with new email address.
Changed my iCloud with above new email address.
NOW - Apple ID appears correct in AppStore Settings, iCloud and AppStore*
If I scroll to bottom of screen in *App Store/Featured, I can see that the Apple ID is my new email.
Upon “updating” Apple ID reflects OLD email.
Deleted accounts, re-added accounts.
Signed out and signed in with new UN/Email
Issue remains the same.

To migrate your data to a new iCloud account go to Settings>iCloud and turn off all synced data (contacts, calendars, etc.), when prompted choose to keep the data on your phone. After everything is set to off, scroll to the bottom and tap Delete Account. Next, create the new iCloud account on your phone and turn on syncing for contacts, calendars, etc again. If prompted, choose Merge. This will upload your data to the new iCloud account.

How to configure Time Capsule etc as a local network server with remote access server and for backups

I'm trying to set up new 3TB Time Capsule as a wireless network server (with remote access) and for backups for use in a small office (of two Macs). We have a late 2011 Intel MBP and a brand new MBA both running 10.8.3. We have two external 1TB hard drives that until now have been attached the MBP for storage and backing up that computer, which up until now was the only machine in use. The MBA is for a new employee and we need to share and work on the same files, both here in the office and ideally remotely too via Back to my Mac. The MBP needs constant access. The MBA only occasional. The TC has 7.6.3 firmware and we've set it up using AirPort Utility 6.2. It is currently attached to the MBP via ethernet and it has internet access via a Sagemcom router attached to TC's WAN port.
We've managed to set up a wireless network and both have wireless internet access through the TC
But there are so many issues I don't know where to begin - so I'll start with a description of what we're trying to achieve:
I planned to use the TC as the main server drive and place all the key folders and files there so that both of us can access them wirelessly and remotely. The MBP would back up to the TC and to one or two of the external hard drives - one being attached to the Mac via USB and the other being attached to the TC's USB port. We would back up the important data on the TC using SuperDuper and copy it to both external USB drives.
So , first of all, is that a sensible configuration? Should the 'server' be the one of the external hard drives attached to the TC USB port, backed up regularly to the TC using SuperDuper?

But when you say 'So using USB drive does make sense if you want to use it as a file store', do you mean a USB drive plugged into the TC? I hope that I can attach an external drive to the TC so we can all access and read/write the content wirelessly via the TC network or remotely.
Yes, USB.. as it prevents the sparsebundle mixing with data files. I guess it does depend on how much data you are talking about.. you can use the TC internal disk if you are careful and setup the sparsebundle with fixed sizes once you create them..
And to be clear, I wasn't planning on backing up remotely via BTMM - only to access the shared folders on the TC data drive or USB external drive attached to it. I'm assuming that's ok?
Yes, that is fine. Sorry I got the impression you were going to do backup over internet.
What is the alternative? Having a Mac Mini that's always on? Do I need OS X Server etc.?
A mini would be great.. you don't need server edition.. but I would see how the TC goes.. since you have it and it is much lower power consumption device. It is just that its design is not really for file storage.
One big problem I have is to do with the sharing permissions. For everything on the TC or attached external drive attached to it, it says I have only custom access and every time I try to change permissions it says I don't have the permission to do that. And if I try to change the owner it says my user name is not valid.
How is the security setup on the TC?
The security is a bit tricky.. I must admit since I run windows computer in the network, that I simply turn on the guest account to read and write access. For a business setup that might not be adequate but it allows me full access to all the files.
If you setup the TC with user accounts then you are in trouble. That makes it very difficult to access, especially if one person already has the file open you may find a second user cannot login. I am not sure as I have avoided the security. IMHO it is meaningless.. since anyone with physical access to the TC can press the reset for one second and has full access.. and can add or change passwords.

Trouble with internet on iPad and iphone

I Have a iPad mini and a iPhone 4s and since I upgraded to 8.1 have had trouble with wifi

Hi Go to settings On iPad Reset Network Settings After Reset enter your Router wireless key Also before doing this turn your Router off for 30 seconds You may need to do this for your iPhone Cheers Brian

Trouble with netgear repeater WN3000RP and iOS 6.1

Hi
I just bought a Netgear Repeater (WN 3000RP) and was able to install it after much trouble. Anyhow, everything seems to work except my ipad now can't connect to the wlan of the repeater. Any other wifi network works with the ipad. All other computers and the iphones work with the repeaters network.
I called the Netgear support and was told that appearently there is a problem with apple iOS 6.1. - however, before I updated it I had the same problem with 6.0.2. Does anyone experience the same problem and is there a solution (except returning the repeater to the store) or do we just have to wait for software updates?
Thanks in advance for any help I can get. I am pretty bummed because I bought the repeater mainly in order to use the ipad.
KR
Imandra

it would be better to contact wifi provider then apple.
if you think it might be a glitch on iphone you can also try settings- general- reset- reset network settings.

Downloaded new OS and having trouble with wifi, bluetooth Facebook and Skype performance

Dowloaded 10.2.1.537
When I first loaded this it had a lot of trouble finding my Wifi again and would disengage. Problem went away after a few hours but it recurred this am. Also affected Facebook.
Skype is loading more slowly and jumps to a black screen for 10-20 seconds. Then it will load and function but only for a few seconds to a minute and then shuts off completely.
Launching Skype also resultd in my bluetooth headset being disengaged sometimes.
Reinstalled Skype to see if that fixed anything.
Tried turning off bluetooth to see if that fixed the skype problem - nope still disengaged.
Cycled my router and cable and still no fix...
Running Z30
Would love to get a fix on this.

Hello,
Given all of your issues, I'd guess that something did not go well with the update, and a clean reload would be in order. You accomplish that either through the LINK software or by obtaining an AutoLoader.
Good luck!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Having trouble with kernal_task, fan, overheating, and lag issues with my Macbook Pro. What should I do?

I've had this problem with my Macbook Pro for the past few months. I am starting to become increasing dissatisfied with this product since it's less than even a year old and going through so many problems. I've taken at least 10 trips to the Apple Genius Bar in the past year.
I've had issues with
1) erratic trackpad
2) wifi connection timeouts
3) kernal_task taking up 300% of my CPU, my fan become crazy and just having my laptop lag to the point where I can't even use it.
I sent in my laptop for repairs last week again and they replaced my logic board and some other things. I recieved my laptop back yesterday, but I'm finding the same exact problem is happening again this morning. I still have warranty and set up another appointment for a few days... but the amount of trips I've taken is really starting to irritate me and my problem still isn't solved. What should I do? Is there another way to solve this or should I just keep going back to Genius Bar...
I regret buying this laptop. =\ It was so expensive but yet has so many problems. I've never had to deal with anything this cumbersome with my past few laptops.

If you've taken it back for the same problems over and over again, I suggest that you start asking for a replacement. Ensure that you've backed everything up to an ext HD and removed your personal data and information. IIRC, repeating problems warrant a replacement.

Network Problems with iOS 6.1 and iPhone 5

I strongly believe that the network connections with iOS6 and my iPhone5 has serious problems. I am experiencing the following issues;
Weak wifi signal at locations where I was enjoying good connection with iOS 6.0.1
Sometime when I enter into a known wifi area, the phone does not connect to wifi automatically. I have to open the Settings App and go to wifi section to get it connected.
Sometimes when I wake-up my phone from sleep, which is sleeping well within wifi range, it shows 3G connection and take some times to get connected to wifi.
I am experiencing fast battery draining when compared to my phone with iOS 6.0.1
FYI, I have already tried resetting my network settings and done hard restarting many times without success.
Please advice any action to solve the problems.
FYI, I have submitted the above to Apple via Apple feedback page.

I am having the same issues with an iPhone 5 and it all started when I upgraded to iOS6.1. I geat a strong wifi signal all 3 bars showing and speedtest shows a 20Mps upload and download connection (I have BT Infinity up to 70Mbps connection), however when I go onto safari or even simplae apps like weather or Sky News I am unable to connect - regularly getting the message "Cannot connect to .... a wifi or 3G connection is required. Occasionally it will work say 5% of the time bit having to switch to 3G and luckily I ahave an unlimited data package but the speeed is really slow ~ 2 Mps. I have searched the web and see that Apple is saying there is a problem with Exchange server getting too meny messages and thus denying access but have followed the guidance given and reset the phone, resey the wifi connection and no change I can only use the phone on 3G. I believe there is a big problem here and Apple need to get a fix out pretty quick. If you read this and have the same issues then please log them so Apple know how big an issue this is. I know it is not a wifi issue as getting great wifi on my iMAC and wife's iPhone 3.
regards
Steve

Networking troubles with ABIT BP6 board and Solaris 8

Similar Messages

Maybe you are looking for