Networks not showing up in airport

My airport is on, but no networks are showing up. Just started to happen. Everything was fine until I installed an airport express. The airport express is on and working, but not showing up as a network too.
Any thoughts out there?
Thanks!

Same problem here. Although I'm using Leopard from a clean install. It says searching when i first click open the AP menu open, but then it just shows the network I'm on. Though once and awhile the other networks briefly show up too.....

Similar Messages

How to setup a guest network when the dialogue boxes do not show up in AirPort Utility 6.1

How do I setup a guest network when the dialogue boxes do not show up in AirPort Utility 6.1?
I see screenshots where there are boxes to 'enable' guest network but these simply do not apear on the Wireless tab in AirPort Utility

I now have a guest account, thanks to you!
I did the factory reset and was able to set up the guest account.
There were 3 problems, all of which I was able to solve.
The first problem was connect to Ethernet, which I selected by WAN port, as shown in the first screen shot. This page used to read just Ethernet and the Bridge Mode.
The second problem was whether to share a range of addresses or share a public IP address. I selected share a public IP address as shown in the first screen shot. I had tried the range of IP addresses in my earlier attempts, the ones that failed. Hopefully this will have no effect.
I have forgotten what the third problem was - only excuse is a few too many flavored drinks. I didn't have any problems solving it though.
What is really weird is I can log on to Guest and use on my iPad (first generation), my wife's iPod Touch (third generation), and my wife's 2011 MacBook Pro. I can't log onto Guest on my 2008 iMac, even after a restart. I get the image below.
Since I don't lug my iMac around a lot and it is connected by Ethernet, while my little make it right brain says figure this out, I am not going to worry about it.
Thank you again for your time and patience in helping me solve this.
Eric Root

HAAALP!!! AIRPORT EXTREME NOT SHOWING UP ON AIRPORT UTILITY

I have two airport extremes one to make network and one to expand it. the one i have to make the network is working fine and is a FINE peice of machinery. but the second one i have to extend my network will not show up on airport utility. and no i am not a stupid and didnt plug in the wires right everything is in perfectly and i use to be able to configure it then one day it just stops so i reset and configure it with airport utility. but after it restarts the airport and updates it. it will not show up on airport utility. PLZ help i have tried everything reset it a millions time and some times it will show up then i will change the settings again!! and it will not show up again!!!!! plzz plzz HELP

they are already in the same room and i am doing it on the same computer and it feels like it has gone into a land it can not come back from. also i just realized that it stays amber constantly like its in its startup process. and after a while the light just goes OFF. so idk and i have hard reset it and isnt it supposed to flash lights (cause it doesnt) when i hard reset it. well idk its weird its like it take forever to startup or something cause all of the sudden it will show up on airport utility but after i configure it again it restarts and can not be found again. ;{

Airport extreme not showing up in airport Untility

My airport extreme is not showing up on my mac in airport utilities, was blinking amber I unplugged it back to green but still not showing up in airport utility

Suggest that you restart the entire network by powering everything off...order is not important...and starting the modem first, then AirPort Extreme, then each device one at a time.
Temporarily, connect a spare Ethernet cable from your Mac to one of the LAN <-> ports on the Time Capsule.
Check to see if AirPort Utility can see the AirPort Extreme
If this works, when you have completed checks or adjustments on the AirPort Extreme, you can disconnect the Ethernet cable.

Is anyone else having trouble viewing the SEC network via Watch ESPN on a 2nd gen Apple TV? Software is up to date, but SEC network not showing up as a channel. Using Xfinity - and it appears on iPhone5 but not on iPad2 - both of which ar

Is anyone else having trouble viewing the SEC network via Watch ESPN on a 2nd gen Apple TV? Software is up to date, but SEC network not showing up as a channel. Using Xfinity - and it appears on iPhone5 but not on iPad2 - both of which are current on IOS. Help!

the wifi router could also be blocking
and to really test if the windows firewall is the problem then try turning it off!
if that scare you too much then disable the internet modem / cable modem or the likes while you test
always remove more and more factors when troubleshooting sooner or later it will work and you can narrow down which factor did the job and work on that

AE does not show up in Airport Utility

Hello,
As a disclaimer, I know next to nothing about wireless networks. Here is what I have: 2 G5 towers and MBP. Tower is NOT wireless. Cable comes in and goes to modem > modem to Airport Base Station > to D-Link Router. All computers have a direct connection to the D-Link providing 10/100/1000 connection. I also have an Airport Express that is connected to our stereo system to stream iTunes... at some point, and I am not sure when, the AE quit working. I can connect from the laptop upstairs to the Base Station downstairs... but when I open the Airport Admin utility, the Express simply doesn't show up? I have a blinking amber light on the Express. I did a hard reset on all units (AB, AE, and router); but nothing. At one point, this configuration worked just fine. My wife went to use it today and that is when we found out that it doesn't work anymore. What am I doing wrong??
Mike

If you are using AirPort Utility 6.x, or AirPort Utility for iOS devices, printers do not "show up" in the application at all.
This has no bearing on whether or not the printer will function as long as you have installed the printer using Print and Fax on your Mac.
If you are trying to print from an iOS device, you will not be able to accomplish this unless you add additional software to the iOS device.

Airport express green but not showing up in airport utlitity nor airtunes

Hi,
I'm trying to troubleshoot a problem for my parents. They have a westell dsl modem wireless access point in their office. To give them better reception in the rest of the house I hooked up an old airport express I had lying around. It works fine and has extended the network perfectly (green light etc.) BUUUTTT why does neither the airport utility nor an ipad, nor itunes "see" the speakers or the even the express ?
What am I missing?
I wouldn't have to have an all apple networking? I seem to remember that i have used the express at hotels and it showed up no problems...
Thanks,
Philly
Airport Express is one of the first ones. Computers running lion and mountain lion. iDevices on the latest 5.X

Hi Carolyn
Thanks for your reply. I'm running 10.6.4.
Unfortunately - no luck with that solution. The Kitchen Airport Express also does not show up in the air tunes on my Apple TV.
I have had no problems with getting airport expresses to show up in air tunes before adding this Dlink to my set up - I think it is something to do with the fact that the DLink is plugged into my Airport extreme. (I have tried DHCP off and on).
Thanks

Not Showing Connection to Airport Extreme

We have been using the AirPort Express for a few months now, and everything has been going extremely smoothly, every once in awhile it would seem to be getting very slow, but other than that, me and my family of four could easily use it with no issues what so ever. But, about two days ago, it stopped working all together. On a mac lap top when you would try to connect to the wifi, there would be a exlimation mark over the full bars of wifi. Therefor, I called my internet provided, and was on the phone with them for about three hours yesturday, and at the end of it, we got a new modem to see if that would work.
They gave me a ARRIS, and hooked it up to the AirPort Express. Comcast tooled me to wait about thirtee minutes for it to start working. And, nothing happened. I was on the phone with Comcast again today, and it seemed like we litterly got no where. But, I have identified that it is the AirPort that is the issue. I am currently using my laptop pluged in using an ethernet cable to the modem, and it works fine. But now, it doesn't show that the AirPort is even up, therefor I can not connect to the settings, like I could have before. The light is currently blinking on the AirPort Express, and that is about it. The only things I have tried are hitting the reset, than doing a facotry reset, none which have worked.
If anyone knows why this is happening, it would be greatly apricated,
Connor

Ok,
I have done this, and nothing worked. Therefor I went to the Apple Genius bar to see if they could to a quick fix for me. They did something to it, renamed it test, and thats as far as I got with them over there. But, when I plug it in now, I can see the network. I was apple to get into it, but there is still no internet, and a exlimation mark over where it would show your connnection.
On the app, it is currently giving me two error messages. The first being Internet Connection, " Your AirPort base station does not have a valid IP address. Make sure your AirPort base station is connected to your broadband modem or local network, verify your settings, and try again. If you still can't connect, contact your Internet sercer provider". And the second being No DNS Servers, "This AirPort base station doesn't have any DNS server addresses and might have trouble connecting to the internet."
Thanks you for the responce again,
Connor

Extreme not showing up in airport admin

Sorry in advance for the long post.
long story short: neither my airport extreme nor my airport express appear in my airport admin utility after resetting both. I'm still able to connect wirelessly to the internet, though. I can't do maintenance on my network or name the base stations now. Any ideas?
long story long: i use an airport extreme to create a wireless network in my home. My TiVo is also connected to my network. I use an airport express fror Airtunes.
A few weeks ago, the network no longer worked - the problem was with my ISP, and now is fine (I can connect wirelessly to the net again). Problem is, now I can't get either the extreme or the express to show up in my airport admin. I'm connected to the 'net via my now 'unnamed' ("Apple Airport ed2B..) wireless network. Unfortunately, i can't do anything else, like name my base station, enable my express to connect to this unnamed network, connect TiVo wirelessly, etc.
PowerBook G4 Mac OS X (10.4.8)

Suggest that you restart the entire network by powering everything off...order is not important...and starting the modem first, then AirPort Extreme, then each device one at a time.
Temporarily, connect a spare Ethernet cable from your Mac to one of the LAN <-> ports on the Time Capsule.
Check to see if AirPort Utility can see the AirPort Extreme
If this works, when you have completed checks or adjustments on the AirPort Extreme, you can disconnect the Ethernet cable.

"Network" not showing up

I have an iPhone 4 and when I go into settings>general, the Network tab is not showing up. It also says that I have a VPN, but will not show an APN. I downloaded the iPhone Config Utility, but I'm not sure what I need to do once I have that open to fix this problem. Is it even fixable? I just started using StraightTalk today and want to get all this figured out so I can have access to data. Any help would be MUCH appreciated!

There are two laptops already on the network and working. On the new laptop, when I go to sign on to the network, there is one named "linksys" on it but not "ralphsnetwork". When I put the wireless code in, I get "wireless code mismatch". The other two laptops show "ralphsnetwork" as the network they are connected to. Should the name of my network show up on the new laptop? Or is the one showing up named "linksys" actually my network. If it is, my wireless code will not work on it.

Other itunes on network not showing up in source

hello
we have a network of several macs. on each mac we have share i tunes set up but other peoples itunes not showing up in source.
can anyone help?
firewall port is checked for itunes, and itunes prefs say share my itunes. apple sharing is on. each computer can see each other and work in other "modes" for networking. n
not sure what the issue is.
any help appreciated.
tahnks
wayne

firewall port is checked for itunes, and itunes prefs say share my itunes. apple sharing is on. each computer can see each other and work in other "modes" for networking
Just a thought.
You did not mention 'Look for shared music'.
It's in Preferences>Sharing in iTunes.
M
Edit:
Here are the Knowledge Base articles about sharing music:
http://docs.info.apple.com/article.html?path=iTunesMac/5.0/en/695.html
http://docs.info.apple.com/article.html?path=iTunesMac/5.0/en/705.html
17' iMac fp 800 MHz 768 MB RAM Mac OS X (10.3.9) Several ext. HD (backup and data)
Message was edited by: macmenno

Home network not showing up in Finder

My desktop PC is connected to my router by ethernet; MacBook Pro wireless. Due to a printing issue, I need to copy files from MacBook to PC to print. Sometimes, despite being on, PC does not show up under "Shared" in Finder. Is there a way in Snow Leopard of "seeing" which computers are currently attached to the home network?
Note - this is an intermittent problem; probably 2/3 of the time, the PC shows up no problem!

Open Terminal and issue the following command
ps aux | grep netbios[d]
if you get a line similar to this
_netbios 45 0,0 0,0 2477156 2456 ?? SNs 9:14am 0:02.44 /usr/sbin/netbiosd
then the daemon is running, otherwise issue the following command to start netbiosd permanently
sudo launchctl load -w /System/Library/LaunchDaemons/com.apple.netbiosd.plist

Files/folders not showing up with Airport Disk but are there?

I've recently bought the Airport Extreme, I was all excited about Airport Disk but there is a weird, extremly annoying bug.
On my USB hard drive connected using Airport Disk, I have a folder called music. When I open this folder, OS X starts reading the directory and files/folders show up one by one, but then it just all disappears - and the folder shows nothing. In Windows, it shows nothing at all in the folder. However, when I reconnect the drive using USB to my MacBook Pro, all my music is there and I can see all the files.
I have a feeling this is something to do with this:
http://docs.info.apple.com/article.html?artnum=305040
as I have German and Japanese music files imported by iTunes which are not named in English (ie the filenames are encoded in Japanese etc etc)
Another strange thing is, in Windows, if I type the direct path to a folder (which is inside the supposed empty folder) I will be able to access it.
What's going on Apple?...
Anyone else got this issue?...
Thanks
macbook pro Mac OS X (10.4.9)

Hi Everyone,
I was experiencing the same. on the XP box it just wouldnt show anything period and on the Mac, the finder would briefly display the contents of the drive before disappearing. Spoke to Tier 2 and they thought I should reformat the drive, since he thought it likely that due to severing the drives connection that the format was corrupt...
I did manage to fix it myself and I'll tell you how. First I hardwired the drive via USB to the Mac. noticed an item called FROM which had no size, no date modified and type was --. I deleted the RECYCLED folder (which results when you delete something from the drive thru XP)
then i hardwired it to the PC. deleted the "FROM" folder which in this case was a file folder, and 237MB approx in size. I also deleted the ".DSStore" and ".Trashes" files. .DSStore is basically the icon cache and .Trashes is when you delete something on the airdisk from the Mac. reconnected the drive and POOF! it worked Problem is now solved.
So to summate, i think in my case it was more the discrepancy between the FROM not showing up as anything on the Mac, versus it being a full fledged folder to windows xp. i just thought i would pass this along...
Macbook C2D 2.0GHZ Mac OS X (10.4.9)

Older airport express not showing up in airport utility - want to extend network

I just bought a new Airport Extreme so that I could use my older Airport Express to extend my wireless network. The Extreme is working fine. Set up was easy. Airport Utility isn't finding my express - no matter what I do - and I'm at a total loss. Please help me find it and then extend my network. Thanks!

If you decide to keep the new AirPort Extreme, you will need a newer "n" version of the AirPort Express if you want to try to extend the network using wireless only.
A "refurbished" Model A1264 would work, but it will only extend one band from your dual band AirPort Extreme.
A "new" Express, Model A1394 would be recommended since it will extend both bands.
You do have the option to use the old AirPort Express, but that would involve using a permanent wired Ethernet connection between the AirPort Extreme and AirPort Express.
Unfortunately, it is not possible to predict wireless performance in advance when the signal must pass through numerous walls and or a ceiling. For that reason, it would be a good idea to understand the store's return policy in advance if you want to try a new or refurbished Express.

USB Hard Drive not showing up in AirPort Utility

I have been using this AirPort Extreme for over two years now and it's been working fine. I finally decided to buy a self-powered USB hard drive so I can share it over the network. However, after I unpacked the hard drive, connected it to my Mac and reformatted it to HFS+ Journaled and GUID. I plugged the hard drive into my AirPort Extreme's USB port and waited. I looked in my AirPort Utility and saw nothing in the disk list.
I spent hours searching online and discovered that I am not alone in this problem, although solutions are rare. I did try one solution where I hooked up the USB hard drive to a powered USB hub and the hub into AirPort Extreme. It actually worked once and after I rebooted everything, even though the hard drive still showed up in the disk list, no computers can connect to it. Although if I connect the hard drive directly to a Mac, it would still work perfectly.
Having a USB hub is not a long term solution not that it's working anymore anyway. I would appreciate any suggestions you may have, thanks!

Weilishu wrote:
Thanks for the response. However, I'm not sure what you mean.
So far my experience is far from "Just connect the external hard drive to the USB port on the back of your AirPort Extreme and — voilà".
did you read the support article Daddy linked ? it clearly says
JGG

Networks not showing up in airport

Similar Messages

Maybe you are looking for