New airport extreme loses power.

I am using my new ME918LL/A Airport Extreme as a bridge to extend a home network. After several hours the unit will lose power as is indicated by the light going out and the unit being unavailable on Airport Utility. Resets do not work, the only option is to unplug and plug in the unit.

Hi Bob, thanks for your reply... here goes:
First thing to note, when Airport Utility is opened it may take several launches before it even recognizes the ABS. Also, sometimes the status in the Airport Utility says Orange/Yellow for the internet connection even when we can test the connection directly to a MacBook Air and it's fine.
In the smaller window that appears, check to see if there is a listing for Status
If yes, click on the green or amber dot next to Status, and post back the message that you see there
No Status label.
Next, click on Edit in the lower right corner of the same window
Click the Internet tab at the top of the next window
What is the setting for Connect Using?
DHCP
Next, click on the Network tab at the top of the window
What is the setting for Router Mode?
DHCP and NAT
Click the Base Station tab and note the Base Station Name
How many characters, including blank spaces, are there in the name?
Are there any special characters, like an apostrophe, asterisk, dollar sign, etc in the name?
19 characters, no special characters, two spaces
Click the Wireless tab
Note the Wireless Network Name
How many characters, including blank spaces, are there in the name of the wireless network?
Are there any special characters, like an apostrophe, asterisk, dollar sign, etc in the name?
9 characters in the network name, no special characters, no spaces.
The Yosemite operating system has a number of network bugs that are creating issues for a number of users. Are you running Yosemite on your Mac?
Yes, Yosemite on all three Macs, but, again, never had any issue with networking with the previous Airport Extreme. The only thing different between this ABS and the previous one is that i enabled the separate 5Ghz networking option.

Similar Messages

After we installed a new airport extreme, the imac running snow leopard displays black box msgs saying to hold down the power button and or the reset button and then restart your computer. Can anyone provide info that can help resolve this issue?

Experiencing similar issues on both imac and power book: after replacing an original airport extreme with a new airport extreme both computers display a black box msgs that reads: "...turn off your computer by holding down the power button and or the reset button for a few seconds and then restart your computer."...
one of the printers are usb'd to the imac. The printer is not "seeing" the imac nor will it print wireless from the powerbook which was the norm prior to the upgrade on the airport extreme.
Upon restart, the imac does not "see" the wireless keyboard or the mouse until it is "found" again.
At this time the imac or the powerbook can get on line.

It sounds like your computer is getting Kernel Panics. Please look at About "You need to restart your computer" (kernel panic) messages and if the message seen on your display is like the one in the link then you have confirmed you had a KP. KP's can be tough to track down because they can be caused by software or hardware. The first place to start is to post the complete crash log so we can look at it, often there are clues in the log. You can find it at:
/Library/Logs/DiagnosticReports

AirPort Extreme loses ethernet connection

I am running about 20 or so base stations in my school and every once in a while, a couple of the stations loose their ethernet connection. They are still broadcasting wirelessly, but they disconnect from the network. The stations are running fw5.6 and my clients are running 10.4.2 or WinXP SP2. The only way to fix the problem is to power cycle the base station. I also have the older graphite stations which work fine, which leads me to think that this is not a network issue.
Any suggestions?

I also lose ethernet connection. Sometimes once a day, other times 10 times per day. The other day I was so frustrated about losing my connection that I just walked away from it, without cycling power. When I came back (about 30 minutes later) from my cooling-off period, I found that the connection was back. So, with my AirPort Extreme, cycling power is not the only solution. It's not an acceptable solution though.
I was wondering what you mean by your statement, "They are still broadcasting wirelessly, but they disconnect from the network." I'm relatively new to this stuff and this baffled me, which isn't hard to do.

Help setting up Open DNS with new airport extreme

I cant seem to get Open DNS to work with a new airport extreme. The status says I am not using Open DNS and its not filtering anything. I have followed the exact steps for set up listed on their website, checked the dns settings, cleared both caches and restarted the computer, modem and router with no success. I set the airport up in bridged mode, although I tried the other option under setup, but not sure what I was doing? I picked up this router because I wanted easy set up and the apple store assured me it would work with Open DNS. Oh, and I also downloaded the latest firmware update on the router. Can anyone help me with the settings or what else I need to check?

Sorry, I am not familiar with this product, so I checked online to pick up some information. Here I am referring to the information found here:
http://www.dslreports.com/faq/6096
I found that your device is mentioned as follows in the intro under Section 1 of this document:
The BellSouth supplied Westell 2100, 2200 and 6100 models (Models A90-210030-04, B90-220030-04, and B90-610030-06/C90-610030-06, respectively) share many features and functions.
Next, I am referring to the information under Section 2, under the heading of Standard Default Mode Connection (separate hub or switch present). Unless you have changed the configuration on the Westell, this is how your device is operating. In this mode, the Westell device is acting both as a modem and router in one unit.
So, an attached router (AirPort Extreme) must be configured as a switch to work correctly. That is what Bridge Mode is....the AirPort Extreme is operating as a switch when it is in Bridge Mode (which would be the correct setting to use when the Westell is set to its Standard Default Mode).
Any changes that you want to make regarding DNS settings would need to be made on the Westell device, since it is acting as the main router on your network.
In Bridge Mode, the AirPort Extreme simply passes that information through to its connected devices. You will not be able to make any DNS related changes on the AirPort Extreme since it receives that info from the Westel device. Some service providers force you to use their DNS servers, so you might want to check with Bell South or AT&T for more information in this regard.
If you want to be able to configure the AirPort Extreme as the main router on your network, and instruct it to use the DNS information that you want, you will need to refer to the section under the heading of Bridged Ethernet Mode ( separate router present).
Please note that the first item under this heading specifies that "This is the preferred configuration when using a separate external router..." (which would be the AirPort Extreme in your case)
So, it appears to me that this would be the way that you must reconfigure the Westell device to allow the AirPort Extreme to function as the "main" router on your network. In this type of setup, you will be able to enter the DNS information that you want to use under the setup for the AirPort Extreme and it will act as you instruct.
The AirPort Extreme would not be configured in Bridge Mode for this....it would be configured to "Share a public IP address".
The next item in the article specifies that you "Must use a PPPoE client on the Router." This means that the AirPort Extreme would be configured to Connect Using = PPPoE as follows:
AirPort Utility - Manual Setup
Click the Internet icon
Click the Internet Connection tab
Connect Using = PPPoE
You would enter your user name (probably your email address), password, etc in this area. Leave the Service Area box completely blank. Set Connection to Always On, and Disconnect if Idle to Never
Click Update to save the new settings. Power off the Westell device after this and then restart it so that it will pick up the new information that you have programmed into the AirPort Extreme.
I want to stress that this is how I would try to configure the Westell and AirPort Extreme. But, as I said, have not used a Westell device, so I cannot say that this will work correctly for you.
It might be an excellent idea to contact Bell South or AT&T Support to ask for their opinion on this before you decide to change the configuration of the Westel device and the AirPort Extreme.
This type of thing can be intimidating for users, so you might elect to use the services of someone like the Geek Squad at Best Buy, or a similar service from a local computer firm. Perhaps the Apple store could help as well.
If it is not critical that you use Open DNS, you might want to simply leave things "as is", with the AirPort Extreme in Bridge Mode.

New Airport Extreme: no LAN lights, base station not found

I just brought home a new Airport Extreme base station 802.11n to replace a Linksys router which I used without too much trouble (it used to boot me off occasionally, which was annoying). I want to connect to my DSL internet using an ethernet cable. There's also a PC and a Mac in the house that are wireless. However, the Airport Utility doesn't see the AEBS, I've got the classic flashing amber light, and at the back, the WAN light shows a connection to my DSL modem, but I've got no lights on my LAN ports. (I have seen them light up very briefly but they never stay on.)
I've tried resetting the modem and the base station countless times. I've reconfigured using different ethernet cables. I've disconnected the base station for over 30 minutes before powering up again. I can get a connection when I connect my modem directly to the mini. I've tried using different LAN ports to connect the base station to the computer.
What should I try next? It's a really simple setup, and all I'm trying to do is to connect to the internet.
Thanks for any suggestions.

I know you have tried a series of resets, but please try the following with your Mac Mini connected directly, using an Ethernet cable, to one of the LAN ports of your 802.11n AirPort Extreme Base Station (AEBSn), and the AEBSn's WAN port connected (via Ethernet) to the DSL modem.
Try the following, in order, until the Mac Mini is able to access the Internet:
1. If the modem has a reset switch, use it to reset the modem. Wait at least 5-10 minutes for the modem to initialize.
2. Remove power from the modem. If it has a backup battery, remove this as well. Wait 5-10 minutes. Replace the battery, and add power back to the modem.
3. Perform a complete power recycle of your network components as follows:
Modem/Router Power Recycling - Quick
o Power-off the modem, AEBSn, & computer(s); Wait at least 5 minutes.
o Power-on the modem; Wait at least 5 minutes.
o Power-on the AEBSn; Wait at least 5 minutes.
o Power-on the computer(s)
If this fails to get the modem to "recognize" the Internet router, then try the "Full" version.
Modem/Router Power ReCycling - Full
o Power-off the modem, AEBSn, & computer(s). (Wait at least 30 minutes. If possible, leave the modem off overnight.)
o Power-on the modem; Wait at least 15 minutes.
o Power-on the AEBSn; Wait at least 5 minutes.
o Power-on the computer(s)
4. Contact your ISP to have them perform a "modem reset."

New Airport Extremes any more reliable for wifi backups?

I was one of the many folks who spend hours configuring and reconfiguring my network a few years back trying to get Time Machine to play nice with my USB hard drive for the sole purpose of daily automatic time machine backups over WiFi. Something about Apple not technically supporting this practice, but that it *could* work, *sometimes*, *for some people*. In my experience I could get it working for a matter of days at a time before the link would break and my backups would become inaccessible by either wifi or by direct USB connection, forcing me to re backup my entire HD each time it happened, until I eventually gave up on it all together.
Fast forward to today, I still hate having to go through the process of finding my hard drive, plugging into power, finding a USB cable, etc etc etc every time I want to make sure my backups are up to date. Thus, it gets done very infrequently and therefore makes my backups far less useful if I should ever need them.
As luck would have it, over the holidays I acquired the NEW Airport Extreme w/ 802.11n... have these issues been fixed?
All I want is a reliable, daily, automatic time machine backup, OVER wifi, THROUGH the new airport, TO my USB connected Phantom drive. Can it be???

As luck would have it, over the holidays I acquired the NEW Airport Extreme w/ 802.11n... have these issues been fixed?
Apple now officially supports Time Machine backups to a hard drive at the USB port of the "new" AirPort Extreme.
See this Apple support document for confirmation. Look down near the bottom of th document for the pertinent info.
http://support.apple.com/kb/HT5924?viewlocale=en_US
All I want is a reliable, daily, automatic time machine backup, OVER wifi, THROUGH the new airport, TO my USB connected Phantom drive. Can it be???
"Wireless" and "reliable" are two words that really do not go together well, but your chances have improved with the new AirPort Extreme.

New airport extreme network very slow

I just bought the latest AE base station dual band, but am having trouble with the speeds. We have on the network:
1 macbook pro, 1 windows pc, 2 ipads, 1 ipad mini, 1 kindle fire, 2 iphones, 2 ipods (wow we have a lot of products I just realized now that I am writing them all down) a Wii console and 1 mac desktop computer. Oh and I have an airport express in another room set up to extend the netowrk.
Not all of them are on the network simultaneously.
Using the Airport utility (windows version) I have set up the network trying different configurations. Currently I have it set up as:
Radio mode: automatic
Radio channel selection: automatic
wireless security: WPA2 Personal
network options are 5 Ghz is unchecked
country is US
multicast rate: low
transmit power: 100%
WPA Group Key Timeout: 2 hours
use wide channels is checked
All devices can connect to the net, but speeds are at old dial up levels and that of course was NOT my intention in getting the latest router.
Any advice from those who understand things like multicast rate?

You either have a defective base station, it is not set up properly, or there is some form of Wi-Fi interference that is preventing your new AirPort Extreme from providing a clean signal.
What make & model was the router that you are replacing with the 802.11ac AirPort Extreme?

New Airport Extreme isn't working... hardware issue?

Hey,
I recently bought a new 802.11n airport extreme, after having some troubles with a four year old wireless router. My old router would stop working, forcing me to unplug and plug the unit back in to get it to restart. This would happen about once or twice a week. Two days ago I bought the new airport extreme, and successfully set it up (or so I thought). It displays impressive speeds and seemed to work completely fine from the moment I set it up.
Around two hours later however, the unit stopped transmitting. The wireless network disappeared, and even using airport utility I could not see the unit. I took a look at the unit and noticed that it still displayed a green light (I thought this only occurred when everything was in proper working order). I found a solution to be to unplug and plug back in the router. However, a few hours later, the exact same thing occurred. This has been happening every few hours ever since I plugged it in.
I've talked to apple support once, and they took me through the process of hard resetting the router. This didn't fix anything.
Anyway, if anyone has a solution to this problem, I would be VERY appreciative. Also, I can return the unit for a new one within the next 14 days, so if you guys think it's a hardware problem, I would definitely replace it with another unit.
-Thanks

I have the same problem with my new AEBS. The AEBS n Giga is connected via ethernet to my G5. About 2 or 3 times a day my entire network will go down. The AEBS light goes off completely and the Airport Utility cannot find it. The only way to get it back is to power cycle it. I called Apple and was told this is a "known issue" and that I would just have to wait for a firmware update to correct the problem. I'm not happy.... I plan on calling and insisting on a replacement as this problem doesn't seem to happen with EVERY unit. My friend bought one the same day and store that I did and he has no problems. Anyone else experiencing this problem?
Update:
Apple exchanged it and I got a new one today. I plugged it in only to have the exact same problems!!!! The "geniius' at the bar said he had the same problem and it was his modem. Whatever.... Mine's going on ebay today. Too bad, cause when it worked it was great!

New AirPort Extreme will not connect to internet

Purchased AirPort Extreme to replace older D Link 655 router. All of my Apple gear has been plug and play except this
Extreme router. I cannot get an internet connection to save my soul. I tried connecting thru both my MacBook Pro and my HP Pavilion dv6. I just assumed I could move the ethernet cord from the DIR-655 to the AirPort and all would be fine. Not so. I have reset, unplugged and restarted so many times I lost count. Nothing works. What am I doing wrong. I even swapped out at store where I bought thinking I had defective router. any ideas? My wife works from home and I really need a better router with greater reach and thought this was it. Please help.

Simply restarting the modem will not always allow it to reset correctly so that it will issue a new valid IP address to the AirPort Extreme.
Power off the cable modem completely for at least 30 minutes....longer will not hurt. Be sure to unplug the power cord from the back of the modem or unplug the power cord at the AC wall jack. If the modem has an easily accessible battery, pull the battery.
Power off the AirPort Extreme as well.
After the modem power down period, insure that the Ethernet cable from the modem is connected to the WAN "O" port on the AirPort Extreme. Reinstall the modem battery if it was installed previously.
Power up the modem and let it run for 10 minutes by itself.
Then power up the AirPort Extreme and let it run for a few minutes. Check to see if the Internet connection is working correctly now.

How to improve upload speeds with new Airport Extreme?

Hi!
Just plugged in a new Airport Extreme to replace a BT HomeHub 3.0. The wi-fi download speeds have generally increased over a wider range in the house but the wi-fi upload speeds have dropped to under 1Mbps.
Speeds to laptop linked via ethernet appear fine (both up & download).
Initially thought that I may have messed-up the set-up but the fact that the wired connection works fine makes me think this is something to do with the Airport settings - a scary thought as I don't really know much about this stuff.
As range was really the reason for getting the AP Extreme I'm contemplating plugging the HomeHub back in and just trying to use the AP to extend the old HHub system rather than setting up a new AP system...
Any suggestions would be most gratefully received!
Thanks

... just a quick note to say that the appears to be resolved after a long telephone call to apple service dept (very patient - very helpful).
In my naivety I had attempted to revert back to using the homehub (3.0) router and connecting the APExtreme into one of the Ethernet LAN ports but this didn't work! So called the apple helpline & we went back to basics until it worked. One point to note that may help anyone finding themselves in a similar position...
I had followed the instruction to reset the APEBS depressing the button first whilst powered then without power and during the unit being reconnected to power supply thinking tha this would do a full restore to factory defaults (effectively undoing all the messing- around I may have done flounderinng through the settings) but it was only when I was directed to do a full reset through the Airport Utility settings [Edit\Advanced\Restore Defaults] that this worked (for me).
Download and upload speeds are now up to 93% of advertised speeds wired, & wireless with some fluctuations which appear to be network delivery related rather than anything to do with the APEBS. It's working well with an APExpress which had been struggling (intermittentlyout of range) which is connected to stereo and Apple TV.
By the way - thanks to other posts regarding importance of not connecting an audio out cable to phono sockets on the stereo (horrible sound quality) using a redundant CD channel it works great.
All-in-all, very happy with it so far.

PROBLEM with new Airport Extreme

i just bought the new airport extreme and what was supposed to be a simple setup process has taken longer than 10 hours!
please help!
i have 3 computers.
2 are macs, they will be using wireless. 1 is a PC, which will be wired to the airport extreme.
the airport extreme is connected to a VOIP router, which is then connected to the DSL router.
i have always used my old airport extreme without issues, but because i want to connect the PC as well, i must ditch the airport express in favour for one with LAN ports. hence, the troublesome airport extreme.
it doesn't work.
none of my computers can recognize the new network. (even though i've established one, with passwords and everything)
the router flashes amber - internet works, but not wireless.
the router periodically flashes green - ironically, nothing works then!!!!
please help!!!
EDIT: DIAGRAM
1. WHEN IT WORKED:
INTERNET --> PROVIDER ROUTER --> VOIP ROUTER --> AIRPORT EXPRESS --> MAC 1, MAC 2 (WIRELESS)
2. WHEN IT DOESN'T WORK:
INTERNET --> PROVIDER ROUTER --> VOIP ROUTER --> AIRPORT EXTREME --> MAC 1, MAC 2 (WIRELESS), PC (WIRED)

It appears to me that you may possibly have sever conflict issues as well as maybe not having the Network confiqured correctly.
I have a 3 story OLD VICTORIAN and I am using the Old Airport Extreme Base and have expierianced NO PROBLEMS at all.
If I may suggest a different approach.
Try to start from scratch.
SHUT EVERYTHING OFF.
Run an ethernet cable from your Internet Service Providers MODEM to the WAN port of the Airport Extreme Base
Set it up DHCP and you want the Airport to distribute IP's
use the Airport setup assistant and Airport Admin Utility.
Using 2 Routers in the mix unless you have ony one the main to distribute the IP's, IF you have 2 Routers and they are both set up to distribute the IP's there is your problem.
The New Airport Extreme Base is far better then the older model and you shouldn't need another router in the mix at all to get the coverage of your entire house.
Take the Netgear clear out and use the Airport Extreme and the Expresses as you had them before. There is a very good possibility that you will need to do evrything one at a time and step by step.
Do not just plug everything in, and turn everything on and expect it to work. Do everthing step by step with all security disabled to begin with.
Be sure when you do your system reset that you start by powering up the MODEM 1st and wait for it to acquire the signal before you power up the Airport Extreme and again you must wait for it to acquire the signal. You can use the LAN Ports for anyyhing you need HARDWIRED. If you don't wait and do things in the proper order you will have problems, I can't stress enough that it must be done in the proper sequence. Have a look at the Paperwork of either the Netgear's Yellow Phamplet or the Booklet that came with the Extreme to bear out what I explained on the sequence.
Don

Is a Happy Marriage Possible? New Airport Extreme & ADSL Modem/Router

Is a Happy Marriage Possible? New Airport Extreme & ADSL Modem/Router
1. I’m writing from a rural town in Southern Nepal, very close to India. I’m planning to create a new WI-FI network at a small monastery here. Ideally, we will have two parallel wireless networks: the first network produced by an ADSL router/modem and a second network produced by another router in “repeater” mode.
2. Earlier, someone suggested that, when I post a question, I should provide as many details as possible about the situation here. Forgive me if there is “too much information”. I have to make a trip to the US to buy new networking equipment, so I very much want to get this right. Once I return here, I’ll be pretty much stuck with whatever I get in the US.
3. The future routers will live next to each other in an office and could be linked by a cable (if this is the best route to go). We do not wish to “expand” the network (in the sense of making a larger WI-FI network), but rather wish to simply have two networks, hence one ADSL router/modem and one router with the “repeater” function (out-of-the-box without any jerry rigging). Both WI-FI signals need to travel approximately 100 (largely unobstructed) feet.
4. If my dreams come true, the second router would be an Apple Airport Extreme (AX). An Apple router would be ideal because my experience with Apple routers is happy: they are easy to set up, reliable, and secure. Moreover, we use Apple computers and iOS devices here (and the new AX has the “ac” thing which will be preferable as we replace old machines with new ones).
5. Yet, from reading posts and having my prior questions answered on this website, it may be that with an ADSL modem/router, all the ease and happiness of the Apple ecosystem is lost: while Apple routers seem to connect with each other easily, problems appear to arise when users try to inter-marry our non-Apple products with Apples.
6. Our current, super-crappy 2wire 2701hg-t (ADSL modem/router) covers the 100-foot distance without a problem when it is working and there is Ethernet flowing to us. Frequently, our connection is very bad, and I may be unfairly judging the 2wire 2701hg-t. But, based on user reviews on the America Amazon.com, the 2wire 2701hg-t is pretty terrible: first it is simply old and second, among other problems, it seems to have a poor quality power supply unit. I do observe that it frequently seems to be recycling from scratch as if it had turned off and restarted. In any case, we are replacing it since it may be about 4 or 5 years old.
7. In previous posts on this forum, “LaPastenague” responded to some of my earlier questions about AX and ADSL. Among other things, he pointed out that (1) line-attenuation may be contributing to our poor connection and (2) we must choose a modem/router that is suitable for “long lines.” I’ve looked at our current modem/router statistics page; however, there are no statistics for line-attenuation or noise. (As you will see below, my strategy is to get the “better” modem/router that is suitable for long lines.)
8. Concerning our ADSL service, these are the facts I’ve gleaned from looking at the current router’s configuration pages:
Connection Type: PPPoE
Currently, the router is configured to use WPA-PSK security.
Connection Speed: Incoming: 1024 kbps & Outgoing: 509 kbps
(The following information may be unimportant at this time.)
Broadband Link Diagnostics:
DSL Synchronization: UP
G.DMT Signal: UP
PVC Connection: UP
PPPoE Service: UP
PPP Authentication: UP
IP Connection: UP
DNS Communication: UP
9. The ISP (Nepal Telecom) doesn’t supply a modem/router; however, they do have a list of (at times ancient) hardware and hardware vendors:
http://www.ntc.net.np/internet/adsl/adsl_vendersConf.php
10. Concerning what equipment is available here, what I have observed is that generally the ADSL modem/routers for sale locally, and in the far-away capital Kathmandu, and in nearby India are often also available in the United States, but they are the cheaper, older models. I will have to buy the new equipment in the US this year. At a different institution nearby, they are using the TP-Link modem/router td-w89016 which they purchased locally, I believe.
11. Based in part on LaPastenague’s earlier advice, I want to buy the TP-LINK TD-W8980 N600 Wireless Dual Band Gigabit ADSL2+ Modem Router (2.4GHz 300Mbps+5Ghz 300Mbps, IPv6 Compatible). This appears to be the most popular ADSL device on Amazon now.
Will this modem/router work EASILY with the Airport Extreme in the manner I’ve described? That is, connecting the two with a cable and creating two WI-FI networks.
12. Also, is it generally correct that the best way to connect them is with an Ethernet cable: https://discussions.apple.com/message/23759755#23759755
13. In fact, does connecting them with a cable help alleviate some of the problems that can occur between the Apple device and the ADSL modem/router?
14. If this will work, what “mode” will the AX device be in (again, in order to have two separate networks with separate passwords)? I have heard of the “repeater”, “roaming” , and “bridge” modes.
15. Are there two levels of passwords which need to be considered? Of course, there is the network and network passwords which we create here and which will be different. But, does the Apple also have to have the ISP password like the principle ADSL modem/router?
16. To set this up, what information do I need from the ISP (e.g., passwords, IPs…)?
I think there are a lot of good reasons to use an AX router. Of course, if it is just going to be very cumbersome then, we would be loosing one of the best parts of using Apple products. So, whoever feels knowledgeable enough to reply to this post, please be sincere if you think it is better to avoid the Apple. Apple can rest assured that I will buy other things from them!
In that case, I’d likely buy a second TP-Link device to create a second network:
TL-Wa801NP [AP Mode Multi-SSID Mode AP Client Mode Repeater Mode (WDS / Universal) AP+ Bridge mode (point-to-point / point to Multi-point)].
Thank you in advance. Long live Apple!
Message was edited by: Jess1911

I am not sure if there are different interfaces but my 2wire does an excellent job with line info.
I get into this from browser.. using main IP.. in my case 10.0.0.138/MDC
In your case it should be whatever the IP of the 2wire is, followed by /mdc
Give it a try.
As you can see it shows vendor and loads of info about the line.
I rate it the best domestic modem for line info.
A good modem actually albeit a lousy router.
MDC is the diagnostics and Management Console.
3. The future routers will live next to each other in an office and could be linked by a cable (if this is the best route to go). We do not wish to “expand” the network (in the sense of making a larger WI-FI network), but rather wish to simply have two networks, hence one ADSL router/modem and one router with the “repeater” function (out-of-the-box without any jerry rigging). Both WI-FI signals need to travel approximately 100 (largely unobstructed) feet.
You are not repeating.. you are simply setting up two routers which are interconnected, so one is dependent on the other.. ie one is your adsl modem router and that will take the main router function. Your second router is really not working as a router, but as wireless access point (and switch if you plug things in).
That is perfectly fine. You are not roaming in this case since both routers are running different wireless names and networks.. but they are actually using same IP range.. all devices are on the one IP network with two different wireless access points.
4. If my dreams come true, the second router would be an Apple Airport Extreme (AX).
Apple router is fine for this. Easy to configure out of the box.
5. Yet, from reading posts and having my prior questions answered on this website, it may be that with an ADSL modem/router, all the ease and happiness of the Apple ecosystem is lost: while Apple routers seem to connect with each other easily, problems appear to arise when users try to inter-marry our non-Apple products with Apples.
The problem arises when you try and interconnect using wireless extend or repeater.. you are not using wireless to extend, you are using ethernet. Wired has no issues.
11. Based in part on LaPastenague’s earlier advice, I want to buy the TP-LINK TD-W8980 N600 Wireless Dual Band Gigabit ADSL2+ Modem Router (2.4GHz 300Mbps+5Ghz 300Mbps, IPv6 Compatible). This appears to be the most popular ADSL device on Amazon now.
Will this modem/router work EASILY with the Airport Extreme in the manner I’ve described? That is, connecting the two with a cable and creating two WI-FI networks.
It is a good choice.. It should be fine considering how poor your line is.. this modem is proving to have a couple of bugs.. it does not handle torrents well but I would suggest your system is not being used for that purpose. It has some port forwarding issues. Again you are probably not going to overload it.
12. Also, is it generally correct that the best way to connect them is with an Ethernet cable: https://discussions.apple.com/message/23759755#23759755
Absolutely best.. only decent method.
14. If this will work, what “mode” will the AX device be in (again, in order to have two separate networks with separate passwords)? I have heard of the “repeater”, “roaming” , and “bridge” modes.
Bridge. Although if it gives issues there is another method, although rather complex to setup.. not something to worry about now.
15. Are there two levels of passwords which need to be considered? Of course, there is the network and network passwords which we create here and which will be different. But, does the Apple also have to have the ISP password like the principle ADSL modem/router?
Only the adsl modem has the ISP authentication.. it is the box that does the link. The TC just piggy backs.
The passwords on the TC are for its Admin, wireless and disk access.
16. To set this up, what information do I need from the ISP (e.g., passwords, IPs…)?
For ADSL you must have the PPPoE authentication username and password.
So, whoever feels knowledgeable enough to reply to this post, please be sincere if you think it is better to avoid the Apple.
hmmm.. I am biased because I see the issues not all the good stories..
The latest airport and Time Capsule seem to have a few pretty severe bugs.. if they happen to hit you, they are extremely hard to fix if you are in the middle of Nepal. And Apple service centre is a long long way away.
I cannot answer your question from the point of view of a person on the ground in remote area. If the economics of the purchase works for you, great. Go for it.
In terms of wireless coverage.. the Asus AC models or Netgear R7000 kill the Apple. Sorry but it is just fact.
See reviews here.
http://www.smallnetbuilder.com/lanwan/router-charts/bar/113-5-ghz-dn-c
That is average.. if you look at the apple router in the worst location by changing the filters, it comes out worse again.
I cannot post the URL to our local forum here.. (apple doesn't allow it). But in testing with apple clients the asus still beat Apple router soundly.
Pure wireless range is not the only consideration.. but in a mixed environment and since the wireless on the 8980N is not too bad.. then buy Apple router for apple client devices makes good sense.
Maybe the older Gen5.. or two of them.. would do a better job.. with a bit more tested and known hardware.
One thing you do need to check.
Routers from every other brand allow you to select country. Any country from anywhere in the world. Apple routers do not.
If you buy an airport in North America it is coded to North America and offers just a few countries.. USA, Canada I suppose.. what else is North America??
You cannot change it to Nepal.
To get the one for Nepal you must buy the model that covers, South Asia I guess.. I am not sure which it is.
See what the license information is for wifi in Nepal as it might be very different to US and therefore illegal for you to run it in Nepal.
If only the whole world would just bow to America.. we could all follow the FCC regs..
http://en.wikipedia.org/wiki/List_of_WLAN_channels
This only applies to the Apple.. the TP-Link etc allows you to choose Nepal or correct country regulations for wifi.
Buying modems has one tricky bit.. that the actual adsl ATM channel is different in different parts of the world. No modem is usually impossible to setup but some can be difficult if it is pre-configured for US.. this is easy to overcome generally as you can download a firmware for another locality, so you can have local settings.

New Airport Extreme (6th Gen) Dropping Connection from Time to Time.

Problem:
6th Generation Airport Extreme drops connection intermittently at random times.
Set Up:
6th Generation Airport Extreme (main router - no hard drive/not a time capsule) located center of house on the main floor. 2 Range extenders each approximately 30+ feet away from main router. First range extender (Airport Express - newest generation) located on the third floor parallel to main. Second range extender (Airport Express - new generation) is located at the end of the kitchen (main floor).
Main Router is connected straight from a Motorolla Surfboard modem on a foyer table at the center of the house.
Range extenders connected to Main Router wirelessly and at wall outlett height.
Previous Setup:
Same setup as above but, with the 5th Generation Airport Extreme instead of the 6th Generation.
Firmware:
All current versions.
Devices:
1 SONY VAIO VGN-FW490J
HP Notebook G60
Several WEMO outlets
1 iPad Mini
1 iPad 2
1 iPhone 5
1 Motorolla RAZR MAXX
Macbook Pro
iMac (wired from main router on foyer table)
Note: All of these routers/range extenders/modem/computers are plugged into surge protected outlets.
Notes:
With the new Airport Extreme my family and I have been experiencing intermettent connection drops. The amber light on the main router turns on and within a few minutes turns green and connection resumes again. This has been happening for a few days now ever since I purchased the new router. This has not happened before with the 5th generation router, which I donated to our church.
I have not exchanged the product yet. I will be initiating a Complete Power Recycle after some suggested solutions in a bit. I have contacted my Internet Service Provider (Comcast) for a line check and found no problems.
Has anyone found any solutions to resolve the intermittent connection drops? Is reverting to the previous firmware going to solve this?
I would like some insights before trying to do all this. Thank you all for your time.
P.s.
I've done a detailed post since posts like these is frequently asked questions on set-up, devices, connections, etc:

Update:
Before I went to exchange my 6th Gen Extreme, I ran through all possible solutions from complete power recycle to no devices connected. I even went out of my way to my cousin's house to test it out. The same problem still kept coming.
I was able to exchange my 6th Gen Airprt Extreme with another 6th Gen Extreme the other day. I set it up how the instructions told me and within an hour it did the exact same problem as the previous 6th Gen Extreme. I gave up and decided to get the ASUS RT-AC66R (ASUS RT-AC66U is the same, just the 'R' is Best Buy's model.)
The ASUS router is just as great as the 6th Gen Router. You can actually get it down to $180 by price matching to Amazon. The ASUS router has 3 antennas that you can adjust according to where the signal is used more. I pointed them more towards the backyard, upstairs, and the living room. The range is by far better than the Extreme because of this. I was able to drive down a good block (3-4 houses down) and still connected to my router. Also it has 2 USB ports which was fantastic for me so I can plug in my external hard drive and a non-wireless printer. It has many more features that I really liked that I didn't even know was possible. The router utility interface is a bit confusing at first but, it's pretty easy once you get the hang of it.
Some features that I liked with the ASUS was the ability to have multiple guest network with time limits. 3 for 2.4gHz and 3 for 5gHz. I think that Airport guest accounts are only allowed 2.4gHz but not a 5gHz. Though I only needed 1 for each but, I can see this working well for businesses.
Another feature is traffic manager. I am able to set specific bandwith for different types of use such as, high priority 80%-100% bandwith for gaming, medium priority badwith 70%-90% for HD media streaming/data transfer, and 50%-80% low bandwith for casual web surfing. It also has it's own "beamforming" so that data isn't free roamed.
Lastly it has AiCloud sync which is basically like having a hard drive into your router but, much like having a Dropbox at the same time.
More or less I think I'll stick with the ASUS router rather than going with the new Airport Extreme. I think that it's more on firmware issue than it is hardware. If you are not willing to switch to another brand and want to keep staying with Apple, I recommend going back to the 5th generation until a new firmware or rebuilt 6th gen extreme is out.
I have not found any problem with the ASUS router and no intermittent connectivity issues.
Now I am not trying to make you buy the ASUS router. I'm merely expressing how great the product is.
I do have 60 days from Best Buy return policy to try out the ASUS (and report of any malfuntions) and if within that time a new firmware is out for the Extreme. I highly doubt I'll go back to the extreme though.
Hope this helped!!

My new AirPort Extreme keeps shutting down and kicking my ipad and iPhoto off while sometimes showing a good connection in utilities but utilities showing no connection.

My new AirPort Extreme keeps shutting down. The status light is off. If I unplug and re-plug it comes back on and reconnects. Also, it disconnects my iPad and iPhone even though the status light is green. I go to airport utilities and the internet dot is amber and the base station is green. I check wireless clients and both iPad and iPhone show excellent connection but are not connected. If I disconnect and re-connect it restores connection. My old AirPort Extreme never had this problem. I read a couple of comments from owners with similar problems and you pushed it off on the iMac or other things. I hope you have an answer for me!

If it has power, an Extreme's status light should never be off.
Try another power outlet. If it still doesn't work, return or exchange it for a new one.

Canon MP 620 not recognised since new airport extreme

I've been successfully using a Canon MP620 printer and scanner wirelessly for about six months but then my old Buffalo AirStation gave up the ghost and I replaced it with a new Airport Extreme. It was a joy to get something out of the box, plug it in and have everything work from the moment I switched it on. The only problem is the Canon has disappeared and I cannot get it to appear either wirelessly or as a USB device. I have tried just connecting it to one computer by a USB cable but it's just not being detected.
We have three MacBook Pro's in the family on airport, a MacPro and an old G4 that connect by cable, oh, and er...a Dell PC. We are running a mix of 10.5.8 and 10.6.1. The main MacBook Pro that was used originally to set up the wireless system is still on 10.5.8.
The Canon still has the same settings in it that it had before. I have downloaded the latest driver from Canon but when I get to the point where it scans for printers nothing comes up whether I set it to USB or Network.
I am so frustrated as it was working so well before.
Any ideas anyone?

Hello and welcome to Apple Discussions.
To add the MP620 on Mac OS X 10.5 as a networked wired or wireless printer, you need to select More Printers > Canon IJ Network. For Mac OS X 10.6, you add the network printer via the Default browser view. But there is every chance that the MP620 is not connected to your new Airport, so you will need to run the network setup tool again.
To configure the network settings in the printer, you will have to connect the MP620 to your Mac or PC via USB. This will let you open the Canon IJ Printer Utility, which lets you configure the network settings. Since this is a Mac forum, I will detail the Mac procedure.
With the printer connected via USB, open Print & Fax and select the MP620 in the list. If you haven't had the MP620 connected to this Mac previously via USB, then it may take a while for the printer to appear in this list. If it hasn't appeared after 30 seconds, then click + to add the printer. Select the MP620 shown as a USB device. At the point when you select to Add, you may be prompted that the printer is already installed. If so, just cancel the install. If not, continue the procedure.
With the USB printer queue selected, open the print queue and click the Utility icon. This will open the Canon IJ Printer Utility. This will show you the USB attached MP620. Select it and press the Network Settings button. This will open the Canon IJ Network Tool that will guide you through adding the MP620 to your new network.
Once the network setup process has completed, you can turn the MP620 off and disconnect the USB cable. Then when you turn the power back on, the printer should now be connected to your wireless network allowing you to add it as a network printer.
On 10.5, with Print & Fax open, click to Add and then select More Printers > Canon IJ Network.
On 10.6, open Print & Fax and click to Add. Select the Default browser view.
In both cases the MP620 should be visible, allowing you to select it and add it as a network printer.
Hopefully this gets you printing again. Please reply if you need more help.
Pahu

New airport extreme loses power.

Similar Messages

Maybe you are looking for