New aluminum keyboard keeping PC from booting?

I just got this new thin apple keyboard (with numeric kaypad) and i plugged it in to my PC and it worked amazing and wonderful and was great for the first few hours)
Until the next day when i tried to start up my computer for the first time with it already plugged in.
My computer refused to boot. Would not start. So i unplug the keyboard and reset my computer and it starts up normally. So then i turned it off again and plugged in the keyboard and try to start up and again, and it got stuck again.
So clearly, it is the keyboard keeping my pc from booting.
So my question is WHY is it doing this, and HOW do i fix it.
The keyboard works perfectly fine otherwise, its just ridicules for me to have to unplug it/ reconnect it every time i go to use my computer.

Fixed it
went into bios and disabled legacy USB

Similar Messages

IPhone + New Aluminum Keyboard + MBP = No Sleep?

I just got the new wired aluminum keyboard two day ago, hooked it up to my MBP through my ACD's USB hub. Somehow the computer just keeps waking up from sleep after a while.
I did an experiment yesterday. Put the computer to sleep mode for entire day and check on it every couple hours. The computer does stay in sleep mode. However, I noticed whenever I have my iPhone nearby, the computer will wake up after a while. Anybody experienced same problem? I did also disabled the bluetooth and wake-for-ethernet.

i hooked my old keyboard back on this morning, observed it for about 40min with my iphone sitting next to it and it stays in sleep mode. I'm gonna let it sleep again tonight using my old keyboard, if no problem then I might have got a defected new aluminum keyboard.

Installing new aluminum keyboard

I'm due to receive a new aluminum keyboard this afternoon and I've got a Mac Pro running 10.4.10.
Questions:
1.Should I apply the new 1.2 keyboard update prior to swapping my old keyboard for the new or install the update and then swap the keyboards.
2. With the new keyboard do I need to re-run the bootcamp 1.4 update or will the update (1.4, already installed) pick the new keyboard up for my bootcamp/xp drive?

"I just tried this. Go into System Preferences -> Display. Turn off Automatically adjust brightness as ambient light changes. Now move the Brightness slider right and left, left and right. Turn on Automatically adjust brightness as ambient light changes. When I changed it from far left to right then left again it was ok."
Hey, thanks for the tip Neil. I was trying to figure out why my computer would dim and then get brighter. It would keep changing after every little thing i'd do. Honestly, it was freakin annoying.

Resetting PRAM with new aluminum keyboard

I just updated the firmware to my aluminum keyboard via Software Update. I still cannot reset the PRAM by the old tried-and-true method of holding down command, option, PR. Lately resetting the PRAM has been needed. Anyone have any idea on how to do this?

joshz -- I upgraded my memory from 1 to 2 G and then reset the PRAM 3 times using my old keyboard. This didn't help. I plugged my new aluminum keyboard back in and restarted holding down the option key. My Mini didn't know how to handle that! It got hung up at the blue screen and went no further. I had seen on another forum the suggestion of replacing the new aluminum keyboard. Apple gave me another which worked fine at my local Apple Store, but acted no different when I hooked it up to my Mini. So -- I still have my problem. I wonder how broad an issue this with folks that have upgraded to the new keyboard on their slightly older macs.

New aluminum keyboard - Zapping pram & bootcamp?

Hi,
I've just bought the new aluminum keyboard running on an iMac core 2 duo - Leopard with all current updates and I'm unable use key commands on booting, (alt=select a boot drive, command-option-p-r =Zap the pram etc)
The keyboard works fine once inside Leopard.
Any ideas on how I can fix this problem?
Regards,
Dave

It could be a firmware problem. The correct keyboard map may not be loading until the OS loads it, which means the old keyboard would be mapped at boot time. You might want to check the Apple knowledge base on this one.

New aluminum keyboard = G5 zombie?

Normally I use ctrloptioneject to put my G5 Quad to sleep. With the new aluminum keyboard and the software update, this key combo turns the computer into a zombie. The mouse cursor disappears as expected, but the drives don't spin down and the screen stays on. Nothing but a reboot will bring it out of this state. I tried the same key combo with my previous wireless keyboard and I get the same results, leading me to believe it's a software issue.
Anyone else getting this?
thx

Ah...it seems the computer didn't like that I plugged the keyboard into my PCI-E USB card. I unplugged my iPod Shuffle dock (which was plugged into the G5's last remaining native USB port) and swapped it out with the keyboard. Now the keyboard correctly puts the machine to sleep. Odd, because I knew there were issues with USB peripherals preventing sleep, but I thought it was limited to cameras and drives, not keyboards.
Of course, now I can't put the computer to sleep with the Shuffle docked, but at least I have control over that.

New Aluminum Keyboard Keys Don't Work

Hi All,
I just brought home my new Aluminum Keyboard that was released along with New iMac. As you see I'm on PowerMac G5.
I've installed Keyboard Update 1.1 and I've got my Fn key working. However, for the life of me I can't figure out how to get f4 key to get to work. There is a new symbol (deshboard) on it and when I was at the apple store I was shown that by pressing the f4 (deshboard) key it would start the deshboard. Mine doesn't. Same thing with f3 (expend) all windows key.
Your help is greatly appreciated.
Thank you,

i have no problem with thes f3 or f4 keys or the Fn key.Plugged it in hit software update and then installed Keyboard update 1.1, works fine
I do have a problem with the right hand Shift key though, sometimes it works and sometimes it doesnt work at all.
Anybody else have this problem or is it all function key issues only/

Num Lock on new Aluminum Keyboards?

Anyone know how to enable Number Lock on the new aluminum keyboards? This is usually not an issue with Macs (as by default num-lock is assumed on), but I use remote desktop to control a Windows server and I can not use my number pad because you would normally need to engage num lock to be able to do this on Windows.
On my old Apple keyboard there was an actual Num Lock button (shared function with the Clear button).
Any ideas?
Thank you.

Try any of the following F13 to F19, because an standard pc keyboard does not have theses keys, so it might be possible.

Number Lock (Num lock) on new Aluminum Keyboards

Anyone know how to enable Number Lock on the new aluminum keyboards? This is usually not an issue with Macs (as by default num-lock is assumed on), but I use remote desktop to control a Windows server and I can not use my number pad because you would normally need to engage num lock to be able to do this on Windows.
On my old Apple keyboard there was an actual Num Lock button (shared function with the Clear button).
Any ideas?
hank you.

Same here, have you figured out a solution?
The iMac aluminum keyboard has no designated key, and the Leopard solutions do not work.

Intel iMac with new usb aluminum keyboard will not recognize boot options

I have a first gen Intel iMac core duo 20". After I replaced the old usb keyboard with the new aluminum usb keyboard, I can no longer boot into single-user mode, select to boot from a different volume (including boot camp), boot from a CD, or boot into target mode. All of the boot key options no longer work. These options do work with an older Apple keyboard. I have all the latest updates including the latest firmware and keyboard drivers. Help Apple, I really need to boot into these different options and with the new keyboard, I can't. I have read several other accounts of this on other sites.

I have an early 2006 intel iMac and am having the same problem with the new keyboard. Called AppleCare, who sent me to the local Apple Store after trying several minutes in vain to cure the problem.
One of the Genius's at the Apple Store pulled up Article 306893, Apple Keyboard (2007): Cannot boot to Startup Manager. This is a document that's apparently not available to the public, as I have the printed copy, but have been unable to pull it up in my searches.
The issue is some intel-based iMacs and Mac mini computers shipped prior to 2007 may not boot to the Startup Manager when holding down the Option key on the aluminum keyboard (2007).
My iMac is listed among the products affected.
The solution they offer is to follow these steps:
1. While starting the computer, point the Apple remote at the computer and hold down the Menu button. The computer should boot into the Startup manager.
2. Use the Fast Forward and Rewind buttons to select the desired boot volume.
3. Once the desired boot volume is selected, press the Play / Pause button to continue booting.
Hope this helps. It works for my system. Still doesn't solve the keyboard issue but offers an acceptable workaround.

New aluminum keyboard for 24" iMac-10-key numbers not working??

I've got a new 24" intel aluminum iMac I've only had for 2 weeks.
Just today, the 10-key number pad stopped working & my programs froze up with no response from the might mouse plugged into the USB port on the keyboard.
The keyboard viewer shows all of the keys being recognized & Apple Hardware Test showed no issues.
I re-booted several times, did a permission repair & ran MacJanitor & when I rebooted again, I don't get any freeze-ups so far, but I do not have the function of the 10-key portion of my new aluminum iMac keyboard.
Very strange, but it does seem to be software related.
Something of interest: Only the 789-456+1230.enter keys are not working. Those above the 789 are working fine.
And to re-iterate, the keys are all being recognized by the keyboard viewer onscreen.
Any help would be greatly appreciated.
dave

I didn't end up taking it in - I created a new user account & there were no problems with my keyboard.
I transferred my home folder to the new account & started basically fresh.
I guess my old user account was corrupted or messed up somehow.
I have done this once before on my 1book g4 laptop & it also worked.
Thanks for the suggestion, I was getting ready to pack it up for a trip to the Apple Store & remembered to try this at the last minute!
Thanks again
dave

Why wireless apple keyboard keep disconnected from mac mini?

Why is my brand new wireless apple keyboard keep disconnected every 5 to 10 minutes from mac mini? the keyboard's battery is 100% full, and the bluetooth connection seems fine. I'm running 10.8.2. Please help...

Hi Barry,
You seem to have solutions ?
Do you know why iPhone 5 could not be paired by Bluetooth
with MacBook Pro Snow Leopard 10.6.8 ?

Where is HELP key on new Aluminum Keyboard?

Instructions for Boot Camp tells me to use the HELP key for the INSERT command in Windows. The aluminum keyboard has no HELP key. Where is the HELP key the aluminum keyboard??

I am having the same issue but only when I run windows XP - I really would like to know how to avoid this. it seems that after about 5 mins. of using the bluetooth keyboard in XP a key just randomly starts repeating until i turn off the computer - I was not able to get it to stop any other way. (it has nothing to do with range as I am 6" from the MBP at all times)
Message was edited by: CADer

Problem with a new aluminum keyboard

I just bought an aluminum keyboard but when i press, for example, the sound buttons my dashboard appears rather than changing the sound. How do i get the buttons working?

I have exactly the same problem. I just replaced my old Aluninium Apple wireless keyboard that got damaged. I am running OS10.5.8 on a 3.06 GHz Intel Core 2 Duo. I just unboxed my new French wireless keyboard that I ordered form the Apple online store, and can use the sound buttons! I get the dashboard or the old F3 key instead.
DMarsh thanks for your tip, the box is unticked, but the F keys are still scrabbled. My old Apple wireless English keyboard is working fine (3 batteries).
I think that the new keyboards are not fully compatible with 10.5. Is snow leopard ok?.
Lion seems to have new functionalities. I understand the need to update the hardware accordingly, but I am not very happy as it is not clearly mentioned that the new wireless keyboard does not properly work with the previous systems!!!! Come on Apple the sound keys should at least work.
I looked on here and could not find any sofware update. I presume that they expect us to upgrade to Lion.
I get back to apple store tomorrow to get a refund or get an old model shipped.

New Aluminum Keyboard

Received new iMac keyboard today, hooked it up, downloaded Apple Keyboard Update 1.1, and rebooted. Except for the F3 and F4 keys, everything works fine. F3 only brings up Expose, and F4 only brings up Dashboard if I assign these keys appropriately in system preferences, and use fn in combo with each. This is with the option to use standard function keys turned off.
Anyone else experiencing this? Any suggestions?

www.macfixit.com posted one guys work around which fixes this problem.
I only followed steps 3 through 5 (I figured why start all the way back at the old 10.4.3 disc) and it worked! I now have a fully funtional F3 F4 keys on my aluminum keyboard.
Apple, are you listening? How about another Keyboard Update to fix this issue the right way?
MacFixIt reader Joe Mullins writes: "I fixed the dashboard and expose keys on my keyboard. The problem is apparently that Dock.app isn't getting updated properly. I fixed it using my original install disks, 10.4.10 combo updater, keyboard update and Pacifist."
Joe's process is as follows:
1. Insert Install disk for 10.4.x and open /System/Installation/Packages/Essentials.pkg/ with pacifist.
2. Within Pacifist, navigate to /System/Library/Core Services. Click on Dock.app and click install. When it's uncompressed, it will ask if you would like to update or replace. Click replace.
3. When that's finished, open the 10.4.10 combo update package with pacifist and navigate to the dock.app again. Click install, and this time when it asks, make sure to click update.. not replace.
4. When that's finished, open the keyboard software 1.1 mpackage, click the arrow to reveal the contents of AppleKeyboardSoftware_Cmn.pkg, navigate to dock.app one more time, click install and then update once again. Not replace.
5. Once this procedure is finished, you can force quit dock.app and the keys should work.

New aluminum keyboard keeping PC from booting?

Similar Messages

Maybe you are looking for