New AP not showing in default group

I got a new 1042 AP and connected it to the network. I have a 2504 contrller with 6 AP's already on it. I thought I could just plu in the new AP and it would show up in the AP group. Instead it shows up as a rouge AP. How do i get the new AP to show up in the default group?
TIA,
Eric

Running Normal Memtest...
Passed.
IOS Bootloader - Starting system.
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
Xmodem file system is available.
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x84000800, 0x40000000
RQDC, RFDC : 0x80000036, 0x00000208
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is up.
PCIE1: VC0 is active
PCIEx: initialization done
flashfs[0]: 146 files, 7 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32385024
flashfs[0]: Bytes used: 5680128
flashfs[0]: Bytes available: 26704896
flashfs[0]: flashfs fsck took 25 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: 44:03:a7:e8:71:f0
Ethernet speed is 100 Mb - FULL duplex
Loading "flash:/c1140-k9w7-mx.124-25d.JA1/c1140-k9w7-mx.124-
25d.JA1"...#######################################################################################################
File "flash:/c1140-k9w7-mx.124-25d.JA1/c1140-k9w7-mx.124-25d.JA1" uncompressed and installed, entry point: 0x4000
executing...
enet halted
              Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706
Cisco IOS Software, C1040 Software (C1140-K9W7-M), Version 12.4(25d)JA1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 11-Aug-11 02:58 by prod_rel_team
Proceeding with system init
Proceeding to unmask interrupts
Initializing flashfs...
FLASH CHIP: Numonyx P3
Radio0 present 8363 8000 90020000 0 90030000 B
Radio1 present 8363 8000 98020000 0 98030000 0
Ethernet speed is 100 Mb - FULL duplex
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-AP1042N-A-K9     (PowerPC405ex) processor (revision A0) with 98294K/32768K bytes of memory.
Processor board ID FTX1710K00G
PowerPC405ex CPU at 333Mhz, revision number 0x147E
Last reset from power-on
1 Gigabit Ethernet interface
2 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 44:03:A7:E8:71:F0
Part Number                          : 73-14034-06
PCA Assembly Number                  : 800-34273-07
PCA Revision Number                  : A0
PCB Serial Number                    : FOC170226AM
Top Assembly Part Number             : 800-34285-05
Top Assembly Serial Number           : FTX1710K00G
Top Revision Number                  : A0
Product/Model Number                 : AIR-AP1042N-A-K9
Press RETURN to get started!
*Mar 1 00:00:1
               *Mar 1 00:00:15.215: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:23.219: AUTOINSTALL: GigabitEthernet0 is assigned 10.13.2.146
*Jan 13 00:54:01.001: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Jan 13 00:54:01.001: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Jan 13 00:54:02.000: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Jan 13 00:54:02.000: %LINEPROTINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Jan 13 00:54:15.656: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.13.2.146, mask 255.255.0.0, hostname ap
*Jan 13 00:55:03.506: %CDP_PD-4-POWER_OK: Full power - NON_CISCO-NO_CDP_RECEIVED inline power source

Similar Messages

af:tree do not show up default tree image like folder or plus icon

Hi all,
I am new to ADF and stuck with the problem where af:tree component do not show up default icons to expand and collapse.I am using websphere. Please help me to know where i am getting wrong to get the icons.
Thanks in advance
Irfan.

quote:
Originally posted by:
bregent
Always include a url when you have questions about your web
pages.
Sorry, newbie to these forums here.
here's a link to one of them:
http://www.onlineschoolsurveys.com/banner_trial_2.html
With this page I tried using a table and put the images in
spots in the table. The empty spots are where there should be
images. The two images that are there were made by other people.
This link is actually quite obnoxious.
http://www.onlineschoolsurveys.com/oss_banner.html.
With this one, again the only image that shows up is one that I
made originally as a bmp export out of Snap Surveys, turned into a
gif in Photoshop (I think). In the table toward the bottom with the
pink squares there should actually be two pink squares, one should
have an image in it. Being a practice page that I did not expect
others to look at I left the obnoxious background. If this is too
annoying, I can remove the background and repost.
Did you define a site in the site manager?
I'm sorry but I do not know what this means. I regularly have
a site at www.onlineschoolsurveys.com. The first link goes to a
page that is actually a part of the website- I tried using a
template I know works thinking that maybe the non-templated page
was flawed. So if you are asking if these were loaded to an active
website: yes, I regularly have pages at that website, but no, these
pages are not intended to be a part of my regular website. I was
just using that space to practice.
Do the linked images exist within the defined site?
Yes, the images were uploaded. They should exist in an image
folder. Although it may be really stupid for me to make a link to
an unprotected list of files, here is the list of images in my
images folder:
http://www.onlineschoolsurveys.com/images/
Since I am new to using a message board for help, please advise me
if I should not post such directories in the future.
Thanks for your quick response.
Mel

Camera new d810 not showing pix up in raw files in elements 11

camera new d810 not showing pix up in raw files in elements 11 and lightroom 4

DNGC 8.7 can be found, here: http://www.adobe.com/downloads/updates/
You can purchase upgrades to LR and/or PSE, here:
http://www.adobe.com/products/catalog/software._sl_id-contentfilter_sl_catalog_sl_software _sl_mostpopular.html

New Field not Showing up in Report.

I have a CR query that I am editing to add a column to my report. When I make my edits, the query runs, but I do not see the new field in the field explorer. The part in purple is what I added. Do I need to add it elsewhere in the code?
WITH SEL_ACCTS AS(
SELECT
CASE WHEN RMSCUSTTYP = 'I' THEN
CASE WHEN Trim(TRIM(RMSLASTNM) || ', ' || TRIM(RMSFIRSTNM)) <> ',' THEN Trim(TRIM(RMSLASTNM) || ', ' || TRIM(RMSFIRSTNM))
ELSE ''
END
ELSE
RMSCMPNAME
END AS "DEBTOR NAME",
RMSACCTNUM AS "CLIENT ACCOUNT#",
case when RMSHOMEPHN = '' or RMSWORKPHN = '' or RMSFAXPHN = '' or RMSMOBLPHN = '' then 'Y' else 'N' end as skipplcmt,
A.RMSBILENUM,
RMSDATEASG AS PLC_DT,
ATTRNYCODE,
RMSGATECD As "Gate Code",
RAND() AS RANDNUMGEN
FROM
REPORTING.RMASTER As A
left join reporting.rcomker b
on a.rmsbilenum = b.rmsBilenum
WHERE
RMSDATEASG > REPLACE(CHAR(CURRENT DATE - 90 DAYS, ISO),'-','')
AND recordtype = 'D'
and ATTRNYCODE IN ({?AGCY_CODE})),
GET_ACCTS AS(
SELECT
"DEBTOR NAME",
"CLIENT ACCOUNT#",
Cast(Timestamp(plc_dt||'000000') As Date) AS "PLACED DATE",randnumgen,skipplcmt,
PLC_DT,
ATTRNYCODE,
A.RMSBILENUM
FROM
SEL_ACCTS AS A
LEFT JOIN
REPORTING.RPRDBAL AS B ON A.RMSBILENUM = B.RMSBILENUM
ORDER BY RANDNUMGEN
FETCH FIRST {?#_of_Accts} Rows Only),
GET_ACTV AS(
SELECT
G.*,
RMSTRANDTE,
ACTION_CODE,rmstrantim,
RESULT_CODE
From GET_ACCTS AS G LEFT JOIN RPTINGDATA.ROACTREACC AS R ON G.RMSBILENUM = R.RMSBILENUM AND G.ATTRNYCODE = R.ATTRNYCODE AND RMSTRANCDE = '9R'
    AND (ACTION_CODE IN('1','2','3','4','5','7','14','16','22','25','26','27','29','36','44','66') OR RESULT_CODE IN ('2','14','56','58','59','60','61','62','66')) AND RMSTRANDTE >= PLC_DT )
SELECT
"DEBTOR NAME",
"CLIENT ACCOUNT#",
"PLACED DATE",
PLC_DT,
ATTRNYCODE,
RMSBILENUM,skipplcmt,
MIN(CASE WHEN ACTION_CODE IN ('3','4','5','7','25','26','27','29')
    THEN Cast(Timestamp(rmstrandte||'000000') As Date)
    ELSE NULL END) AS FIRSTATTEMPT,
SUM(CASE WHEN ACTION_CODE IN ('3','4','5','7','25','26','27','29')
    THEN 1 END) AS ATTEMPT#,
SUM(CASE WHEN RESULT_CODE IN ('2','56','58','59','60','61','62','66')
    THEN 1 END) AS CONTACT#,
SUM(CASE WHEN RESULT_CODE = '14'
    THEN 1 END) AS PROMISE#,
MIN(CASE WHEN ACTION_CODE = '44'
    THEN Cast(Timestamp(rmstrandte||'000000') As Date)
    ELSE NULL END) AS FIRSTMGRRVW,
SUM(CASE WHEN ACTION_CODE = '44'
    THEN 1 END) as MANAGER#,
MIN(CASE WHEN ACTION_CODE = '1'
    THEN Cast(Timestamp(rmstrandte||'000000') As Date)
    ELSE NULL END) AS FIRSTLETTER,
MIN(CASE WHEN ACTION_CODE = '36'
    THEN Cast(Timestamp(rmstrandte||'000000') As Date)
    ELSE NULL END) AS FIRSTSCRUB,
max(CASE WHEN ACTION_CODE in ('1','2','14','16','22','66')
    then 'Y' else 'N' end) as locateacct,
sum(case WHEN ACTION_CODE IN ('3','4','5','7','25','26','27','29') and (rmstrantim between 80000 and 100000 or rmstrantim between 180000 and 210000) and ( DAYOFWEEK(DATE (
                    SUBSTR ( DIGITS (rmstrandte) , 1 , 4 ) || '-' ||
                    SUBSTR ( DIGITS (rmstrandte) , 5 , 2 ) || '-' ||
                    SUBSTR ( DIGITS (rmstrandte) , 7 , 2 ) )) in (1,7) ) then 1 else 0 end) as primecall,
FROM GET_ACTV
GROUP BY
"DEBTOR NAME",
"CLIENT ACCOUNT#",
"PLACED DATE",
PLC_DT,
ATTRNYCODE,
RMSBILENUM,skipplcmt

It's not showing up because it's only in the first With Select - it hasn't been brought down all the way through to the final Select. Here's how you need to change it;
WITH SEL_ACCTS AS(
        SELECT
          CASE WHEN RMSCUSTTYP = 'I' THEN
            CASE WHEN Trim(TRIM(RMSLASTNM) || ', ' || TRIM(RMSFIRSTNM)) <> ',' THEN Trim(TRIM(RMSLASTNM) || ', ' || TRIM(RMSFIRSTNM))
            ELSE ''
            END
          ELSE RMSCMPNAME
          END AS "DEBTOR NAME",
          RMSACCTNUM AS "CLIENT ACCOUNT#",
          case when RMSHOMEPHN = '' or RMSWORKPHN = '' or RMSFAXPHN = '' or RMSMOBLPHN = '' then 'Y' else 'N' end as skipplcmt,
          A.RMSBILENUM,
          RMSDATEASG AS PLC_DT,
          ATTRNYCODE,
          RMSGATECD as "Gate Code",
          RAND() AS RANDNUMGEN
        FROM REPORTING.RMASTER As A
          left join reporting.rcomker b on a.rmsbilenum = b.rmsBilenum
        WHERE RMSDATEASG > REPLACE(CHAR(CURRENT DATE - 90 DAYS, ISO),'-','')
          AND recordtype = 'D'
          and ATTRNYCODE IN ({?AGCY_CODE})),
GET_ACCTS AS(
        SELECT
          "DEBTOR NAME",
          "CLIENT ACCOUNT#",
          Cast(Timestamp(plc_dt||'000000') As Date) AS "PLACED DATE",randnumgen,skipplcmt,
          PLC_DT,
          ATTRNYCODE,
          A.RMSBILENUM,
         "Gate Code"
        FROM SEL_ACCTS AS A
          LEFT JOIN REPORTING.RPRDBAL AS B ON A.RMSBILENUM = B.RMSBILENUM
        ORDER BY RANDNUMGEN
        FETCH FIRST {?#_of_Accts} Rows Only),
GET_ACTV AS(
        SELECT
          G.*,
          RMSTRANDTE,
          ACTION_CODE,rmstrantim,
          RESULT_CODE
        From GET_ACCTS AS G
          LEFT JOIN RPTINGDATA.ROACTREACC AS R ON G.RMSBILENUM = R.RMSBILENUM AND G.ATTRNYCODE = R.ATTRNYCODE AND RMSTRANCDE = '9R'
            AND (ACTION_CODE IN('1','2','3','4','5','7','14','16','22','25','26','27','29','36','44','66')
            OR RESULT_CODE IN ('2','14','56','58','59','60','61','62','66')) AND RMSTRANDTE >= PLC_DT )
SELECT
"DEBTOR NAME",
"CLIENT ACCOUNT#",
"PLACED DATE",
PLC_DT,
ATTRNYCODE,
RMSBILENUM,
skipplcmt,
"Gate Code"
MIN(CASE WHEN ACTION_CODE IN ('3','4','5','7','25','26','27','29')
    THEN Cast(Timestamp(rmstrandte||'000000') As Date)
    ELSE NULL END) AS FIRSTATTEMPT,
SUM(CASE WHEN ACTION_CODE IN ('3','4','5','7','25','26','27','29')
    THEN 1 END) AS ATTEMPT#,
SUM(CASE WHEN RESULT_CODE IN ('2','56','58','59','60','61','62','66')
    THEN 1 END) AS CONTACT#,
SUM(CASE WHEN RESULT_CODE = '14'
    THEN 1 END) AS PROMISE#,
MIN(CASE WHEN ACTION_CODE = '44'
    THEN Cast(Timestamp(rmstrandte||'000000') As Date)
    ELSE NULL END) AS FIRSTMGRRVW,
SUM(CASE WHEN ACTION_CODE = '44'
    THEN 1 END) as MANAGER#,
MIN(CASE WHEN ACTION_CODE = '1'
    THEN Cast(Timestamp(rmstrandte||'000000') As Date)
    ELSE NULL END) AS FIRSTLETTER,
MIN(CASE WHEN ACTION_CODE = '36'
    THEN Cast(Timestamp(rmstrandte||'000000') As Date)
    ELSE NULL END) AS FIRSTSCRUB,
max(CASE WHEN ACTION_CODE in ('1','2','14','16','22','66')
    then 'Y' else 'N' end) as locateacct,
sum(case WHEN ACTION_CODE IN ('3','4','5','7','25','26','27','29') and (rmstrantim between 80000 and 100000 or rmstrantim between 180000 and 210000) and
     ( DAYOFWEEK(DATE (SUBSTR ( DIGITS (rmstrandte) , 1 , 4 ) || '-' || SUBSTR ( DIGITS (rmstrandte) , 5 , 2 ) || '-' || SUBSTR ( DIGITS (rmstrandte) , 7 , 2 ) )) in (1,7) )
     then 1 else 0 end) as primecall,
FROM GET_ACTV
GROUP BY
"DEBTOR NAME",
"CLIENT ACCOUNT#",
"PLACED DATE",
PLC_DT,
ATTRNYCODE,
RMSBILENUM,
skipplcmt,
"Gate Code"
-Dell

OWB is not showing some default options like contol center,import/export

Oracle (11.2.0.1.0) databse is installed on linux.
it is successfully installed on linx.
when i am trying to login to OWB GUI with owbowner/owbwoner.it is opend successfully.
1)when i right click on that 'MY_PROJECT' it is not showing any options like NEW,validate,import/export .
2)Under TOOL tab,control centre is not showing
3)Under TOOL tab,in preferences,it not showing OWB Environment properties
Like this way lot of default options are not showing.
Can anybody help on this issuue........?
Edited by: krishna on Dec 24, 2011 12:48 AM

Oracle (11.2.0.1.0) databse is installed on linux.
it is successfully installed on linx.
when i am trying to login to OWB GUI with owbowner/owbwoner.it is opend successfully.
1)when i right click on that 'MY_PROJECT' it is not showing any options like NEW,validate,import/export .
2)Under TOOL tab,control centre is not showing
3)Under TOOL tab,in preferences,it not showing OWB Environment properties
Like this way lot of default options are not showing.
Can anybody help on this issuue........?
Edited by: krishna on Dec 24, 2011 12:48 AM

New Field not Showing up in Report, part II.

I had this issue with another report, and I was told that I hadn't brought my new field down all the way through to the final Select. With this report, I thought I had done just that, but the new field is still not showing up. I have pasted the code below with my additions highlighted. Can someone tell me what I am doing wrong? Thanks.
WITH SEL_ACCTS AS(
SELECT
CASE
WHEN RMSCUSTTYP = 'I'
THEN
CASE
WHEN
Trim(TRIM(RMSLASTNM) || ', ' || TRIM(RMSFIRSTNM)) <> ','
THEN
Trim(TRIM(RMSLASTNM) || ', ' || TRIM(RMSFIRSTNM))
ELSE
END
ELSE
RMSCMPNAME
END AS "DEBTOR NAME",
RMSACCTNUM AS "CLIENT ACCOUNT#",
rmslastpmt,rmsjdgdate,
CASE WHEN RMSJDGDATE = 0 THEN (RMSCHGAMT+RMSASSCCST+RMSACRDINT+UDCCOSTS1+UDCCOSTS2)-(RMSRCVPCPL+
    RMSXCSRCVS+RMSRCVDCST+RMSRCVDINT+UDCRECCS1+UDCRECCS2)
    ELSE (RMSJDGCHOF+RMSJDGCSTS+RMSJDGINTS+JDGCOSTS1+JDGCOSTS2)-(JDGRECVRYS+
    JDGXCSRCVS+JDGRCVCSTS+JDGRCVINTS+JDGRECCS1+JDGRECCS2)
    END AS BALANCE,
A.RMSFILENUM,
RMSDATEASG AS PLC_DT,
ATTRNYCODE,
RMSSTATECD As "State Code",
RAND() AS RANDNUMGEN
FROM
REPORTING.RMASTER As A
left join reporting.rcomker b
on a.rmsfilenum = b.rmsfilenum
left join reporting.rprdbal c
on a.rmsfilenum = c.rmsfilenum
WHERE
RMSDATEASG < REPLACE(CHAR(CURRENT DATE - 180 DAYS, ISO),'-','')
AND recordtype = 'D'
and ATTRNYCODE IN ({?AGCY_CODE})),
GET_ACCTS AS(
SELECT
"DEBTOR NAME",
"CLIENT ACCOUNT#",plc_dt,
case when plc_dt > 0 then Cast(Timestamp(plc_dt||'000000') As Date) end AS "PLACED DATE",
ATTRNYCODE,
"State Code",
A.RMSFILENUM,case when rmslastpmt > 0 then Cast(Timestamp(rmslastpmt||'000000') As Date) end as rmslastpmt, rmsjdgdate,balance
FROM
SEL_ACCTS AS A
ORDER BY RANDNUMGEN
FETCH FIRST {?#_of_Accts} Rows Only),
financials as (
select "DEBTOR NAME",
"CLIENT ACCOUNT#",
"PLACED DATE",
a.ATTRNYCODE,
A.RMSFILENUM,rmslastpmt,case when rmsjdgdate > 0 then Cast(Timestamp(rmsjdgdate||'000000') As Date) end as rmsjdgdate,balance,
sum(case when e.rmstrancde between '3A' and '39' or e.rmstrancde in ('1G','1U') then e.rmstranamt end) as costspent,
sum(case when (e.rmstrancde between '5A' and '69' or e.rmstrancde = '1P') and postdate > rmsjdgdate then
          e.rmstranamt
                                         end) as pmtamt,
sum(case when e.rmstrancde = '5C' then e.rmstranamt      end) as costrecvd
from get_accts a
left join reporting.rfinanl e
on a. rmsfilenum = e.rmsfilenum
and   (e.rmstrancde between '3A' and '69'
or e.rmstrancde in ('1P','1G','1U'))
and postdate > plc_dt and a.attrnycode = e.attrnycode
group by
"DEBTOR NAME",
"CLIENT ACCOUNT#", "PLACED DATE",
a.ATTRNYCODE,
A.RMSFILENUM,rmslastpmt,case when rmsjdgdate > 0 then Cast(Timestamp(rmsjdgdate||'000000') As Date) end ,balance )
select "DEBTOR NAME",
"CLIENT ACCOUNT#",
"PLACED DATE",
"State Code",
a.ATTRNYCODE,rmslastpmt, rmsjdgdate,balance,c.rmsbalance as plc_bal,costspent, pmtamt,costrecvd,
Cast(Timestamp(max(case when b.hstnewvalu in ( 'L31') then b.rmstrandte else null end)||'000000') As Date) as servicedate,
Cast(Timestamp(max(case when b.hstnewvalu in ( 'L13','P13') then b.rmstrandte else null end)||'000000') As Date) as garnishdate,
Cast(Timestamp(max(case when b.hstnewvalu in ( 'L14','P14') then b.rmstrandte else null end)||'000000') As Date) as levydate,
Cast(Timestamp(max(case when b.hstnewvalu in ( 'L17','P17') then b.rmstrandte else null end)||'000000') As Date) as suitfiledate,
Cast(Timestamp(max(case when b.hstnewvalu in ( 'L12','P12') then b.rmstrandte else null end)||'000000') As Date) as liendate
from financials a
left join reporting.rhistfl b
on a.rmsfilenum = b.rmsfilenum
and b.RMSTRANCDE = 'MT' And b.RMSFLDIMPL = 'RMSSTATUS'
and b.hstnewvalu in ('L12','L13','L14','L17','P12','P13','P14','P17','L19','PJC','L31')
left join reporting.rhistfl c
on a.rmsfilenum = c.rmsfilenum
and c.RMSTRANCDE = 'MR' AND c.RMSFLDIMPL = 'ATTRNYCODE' and c.hstnewvalu in ({?AGCY_CODE})
group by
"DEBTOR NAME",
"CLIENT ACCOUNT#", "PLACED DATE",
a.ATTRNYCODE,rmslastpmt,rmsjdgdate ,balance,c.rmsbalance,costspent, pmtamt,costrecvd, "State Code"

hi David,
some questions:
1) do you mean that statecode is not showing up in the Field Explorer?
2) if you run this through your db query tool, what is the result?
3) if you create a new report off of this syntax, what is the result?
-jamie

New Songs Not Showing Up on Apple TV, Apple TV not in iTunes Sidebar

I have a first-generation Apple TV. I'm able to see my library of music fine, but new additions are not showing up. I've gone into iTunes to try and sync it, but the Apple TV is no longer appearing under devices. I went ahead and turned on Home Sharing, which I did not need before, and Apple TV showed up under Devices, but STILL, my new music additions were not appearing on the Apple TV and there is no Sync option. I turned off Home Sharing and the Apple TV disappeared from the iTunes sidebar. Where do I go from here?

Are the files in the library?
I notice that music and movie categories exist, and I can watch the movies I have converted using handbrake, and iMovie for home movies that we're added to my iTunes library....but... I want to sort this into kid movies, parent movies, and home video categories. Apple TV will be so much more useful if I don't have to use my iPad to air play my home movies. Browsing a single list of video that includes these 3 distinct functional categories is pretty lame. Where is my apple freedom here?
I expect this fixed or more easily configured with the new Yosemite and iOS update. I hope there is an Apple TV update to make this better too.

Creating new track - software catalog new product not showing up - Help!!!

Hi,
Creating a new track for custom development.
A new product has been added in the software catalog in SLD.
SLD and NWDI (netweaver 04) are on the same system.
The new product is not showing up when trying to select in the new track, Software Components for Development section. Why??
Does the server need to be restarted after adding a new product? This is difficult for us as SLD has production systems tied to it!!!
Thanks in advance
Regards, Neeta

Thanks - This did the trick. I have awarded points!!!!
Regards, Neeta

New users not showing up while trying to set folder permission settings

Server 2012
This is a new virtual domain server and file server in a starwind cluster, I just started migrating users last week.
This last weekend (two days ago) the cluster crashed while doing windows updates on this server. I have been unable to get it to download any updates since without crashing, not sure if that is related to this issue somehow.
I added some new users today and got them all logged in and their data transferred over. good. But then I went to this shared folder that everyone has a mapped drive too and tried to add them in the security tab of a sub folder but their accounts will not show
up when I search for them. Any account I added previously to last weekend show up, students, mine, etc.
even if I select the exact OU the accounts are located in, even if I type their whole name and domain. In AD the accounts are there.
If I log into the backup domain controller Their accounts show up there while in a folder security settings tab. They are listed in active directory on both domain controllers.
I have exhausted myself on Google search.
What the heck did I break?
Maybe I should run
DISM.exe /Online /Cleanup-image /Restorehealth
Not sure if I will lose any data doing that or what the repercussions would be..

Hi Dustin,
If the DC is having USN rollback issue, we can resolve it by demote then re-promote or restore the DC using a supported method such as using System State backup to restore.
More information for you:
USN Rollback, Virtualized DCs and improvements on Windows Server 2012
http://blogs.technet.com/b/reference_point/archive/2012/12/10/usn-rollback-virtualized-dcs-and-improvements-on-windows-server-2012.aspx
Best Regards,
Amy
Please remember to mark the replies as answers if they help and un-mark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

New HDD not showing in disk utility

Help please!
i can up on a broken G5 i have replaced the HDD. now i am trying to install tiger. but the new internal HDD is not showing up in disk utility.
i plugged my passport in and it popped right up.
some one please let me know what you think.

Well, having a had hard drive connected may cause a grey screen (if the system cannot successfully perform a check of connected devices). Not sure about the fan.
If you have not done so yet, be sure to try resetting PRAM
http://support.apple.com/kb/HT1379
If that does not help, you can also try resetting the SMU (power management).
http://support.apple.com/kb/HT1767
Follow the procedure precisely.
It is also possible that the old drive was not bad and your iMac has some other problem. Did you ever test the previous drive on another Mac (or connected externally) to confirm it was faulty? That +other problem+ may be what you are experiencing now.
Also, I asked this previously but, are you able to start up the iMac using the optical drive, with a Mac OS X installation disc in there?

New movie not showing up in iCloud

New movie "X-Men:Days of Future Past" not showing up in iCloud.
Thanks

If you haven't already tried, you might try going to System Preferences>iCloud, uncheck Documents & Data, restart your Mac then go back and check Documents & Data again. If this doesn't help, you might need to try resetting the iCloud Documents & Data service as explained here: iCloud: Resetting iCloud Documents & Data service.

New Podcast Not Showing Up In Searches

I received approval for a new video podcast form the iTunes store about two weeks ago, but the show still does not show up on searches in the itunes store.
The link to the podcast works fine, but it doesn't seem to exist when searched. Anyone have any insight? Any clues how to resolve?
This is the email I received:
Dear Podcast Owner
Your podcast, located at [ http://feeds.feedburner.com/DrBrown ], has been approved. You should expect to see it in iTunes within the next few hours. When it's available, you will be able to access it with the URL below.
http://phobos.apple.com/WebObjects/MZStore.woa/wa/viewPodcast?id=264538009
If you have questions or wish to make changes to your feed, please consult the technical spec at http://www.apple.com/itunes/podcasts/techspecs.html. The spec contains detailed information about key topics like adding "cover art", changing your feed URL, and adding other helpful iTunes-specific tags to your podcast.
There is also an Apple Discussions Forum exlcusively for podcast producers, located here: http://discussions.apple.com/forum.jspa?forumID=1107. If you have a question or a problem that the technical spec cannot answer, the community of iTunes podcasters may be able to provide valuable guidance.
Sincerely,
The iTunes Store Team

I'm gonna have to go with "epontius' postulate of unfound podcasts" on this one, my friend. (Look at the last post in the linked thread.) You are but one further confirmation of the hypothesis.
What this means to you is: it is becoming more evident that podcasts with only one episode are not searchable in the iTMS . . . and you only have one podcast in your feed. Update your feed, put up another 'cast, and I bet that your podcast will become searchable a few days afterward.

New episodes not showing up in iTunes

I have added a new episode (item) to my feed and pinged iTunes and the new episode will not show up. The feed was validated and is in the proper format.
When people subscribe, the episode is available and workign fine.
Any way idea on how to get the episode to show up in the listing?
http://advisor.morningstar.com/rssdata/xml/getchoatepodcastdata.xml

Yeah. I checked on this yesterday and it seems to be broken still. I've starred at the code for quite a while and for the life of me can't see what's wrong.
My only other theories are:
1) it for whatever reason doesn't like the formating, no line breaks, just one long string...which in theory shouldn't make a difference...but this is Apple we're dealing with so who knows.
2) doing a search for Morningstar, brings up several podcasts...the one we're dealing with here "Morningstar Advisor" and another similarly named "MorningstarAdvisor". Both seem to have different content. Not sure if iTunes might be confused into thinking that this is a duplicate feed and is no longer updating it.
Erik

Nokia e71 New messages not showing in inbox

I recently updated my nokia e71 with the new software from pc suite, everything went fine but i recieved around 3 messages just after I had restored all my data onto it, I went into the inbox to read them but its showing no new messages. On the message menu my Inbox logo has a read star indicating it has new messages but they are not showing up, its also saying I have 4 unread messages when I synchronise my phone to my pc yet I cant read them via the pc. Help please!!
(Ive reset, restored to factory settings & rung nokia support with no help)
Message Edited by beckuhgreaves on 19-Jan-2010 04:21 PM

If you have a memory card, check to see if the phone is still storing messages in the same place. Example, if the phone is currently set to store messages on the phone memory, switch it to the memory card and see if the messages then show up.
If I have helped you with your problem in some way, please take a little time and hit the kudos button in my post. Without your feedback, I don't know if I am being helpful or should just be put out to pasture.

New portlets not showing up in portlet repository

I have created a couple URL based portlets and registered the provider with my portal. When I go to the portlet repository to add the new portlets to a page, they do not show up. If I go the Providers Tab on the Portal Navigator Page, I can see them.
I suspect this has something to do with my coworker trying to get the Web Cache working though he can't tell me why my portlets aren't showing up.
Any one have any ideas?

Web Cache shouldn't impact this (but I'm not saying that it isn't ;-)
Try the following:
1) refresh the portlet repository by clicking the "refresh" button in the provider registration page
2) check the security settings on the portlets - portlets will not be displayed if either the portal security (applied via the portlet repository) or portlet security (applied by adding a SecurityManager to a portlet) denies access

New AP not showing in default group

Similar Messages

Maybe you are looking for