New battery isn't detected on Equium A300D-16C

Hi,
This is my first post on the site. I have an issue with a new battery on my Equium A300D-16C. (no battery detected)
The original one that I had for the computer died after two years of use so I had to order a new one as a replacement. I have received it and it itself works fine, giving me 90 minutes charge. But the problem is that it isnt detected by the computer when I click on the power icon on the bottom bar of screen, so I dont know how long I have left with it. Also, the orange light that indicates it is charging should go white upon it being full of charge, mine just starts flashing orange after a while (is this when it is fully charged?).
I took the mains out of my computer a few minutes ago and it cut out and I had to switch it back on again, despite the battery being in and it being full of charge (as it has been in all day and the mains have been in for decent length periods).
What can I do to solve this?
Worth mentioning I am not too good with computers so everything might be best explained really, really simply as I am not the cleverest when it comes to this area.
thanks

> Now when i take the mains power out, the computer cuts out and shuts off within minutes without it being able to be turned back on
Seems the battery is empty and therefore notebook shuts down when AC adaptor has been disconnected.
There are two possibilities:
Either the new battery is faulty or there is something wrong with motherboard power supply electronic.
I think both should be checked.

Similar Messages

Equium A300D-16C - Battery not detected after replacement

I have a Equium A300D-16C. The original battery was shot so I purchased a Genuine PA3727-1brs 12 cell battery. I have put it in the laptop it appears to charge it but in the corner it still says no battery detected even though its on charge. When I take out the charger it will say unknown remaining.
I have tried the usual tricks of going into device manager and uninstalling the apci compliant control and still it has not sorted it self out. I have also updated my bios to the most recent one. I just wanted to know what else could I do so I can see how much battery is left and if the laptop can recognise i.,

Hello
Is it an original Toshiba battery from an authorized service provider?
Usually the new battery should be detected after first start I would recommend charging the battery while notebook is turned off. Then start notebook with battery only and check if its recognized properly.

Equium A300D-16C - display not working

My girlfriend has an Equium A300D-16C which has been having a few problems lately.
For the past few months, whenever she turns the system on, the display doesn't fire up and it takes several attempts for it to come on.
The strange thing is whenever this happens the system does still boot normally as you can hear the Windows 7 start up sound.
I have been looking into this issue for quite some time now and I'm starting to run out of ideas.
Originally I thought it could've been a cabling issue but upon stripping the laptop down I found the cable was still firmly in place.
I have also tried removing the RAM, HDD and DVD drive but it still doesn't fire up. On the odd occasion it has started up when doing this but upon rebooting it hasn't started again.
I am thinking this could be either a power issue or the motherboard is on its way out. This problem is gradually getting worse (it took over 20 attempts turning it on and off this morning) so eventually it won't come on at all.
To clarify, the system will boot after many attempts but most of the time the display will not turn on (not even the backlight). It does work with an external display on the HDMI so the GPU is working.
I have tried holding the power button with no power source to discharge the system but it doesn't help.
I have also noticed that if you hear it boot and close the lid, upon reopening the lid the display will come on but with the wrong resolution (1024x768) which just puzzles me even more.
Any ideas on what could be wrong? I would rather repair this than just buy a new one as its still a decent system apart from this problem.

It is always problematic to discuss about problems that happen from time to time. Ok in your case most of the time it doesn't work but when it works there is connection between display and mainboard.
On this virtual way we can just speculate what the problem can be. Maybe connection to the mainboard, maybe display controller, display cable, display connector. Who knows?
If there is no even backlight I presume display doesnt get the video signal at all. It must be something on mainboard side.
What you can do? You can contact nearest service and ask for help but if they will say that mainboard must be exchanged it will be pretty expensive. You can try to find similar model on ebay with broken display or some other hardware failure (not mainboard) and exchange the mainboard.
It is really not easy to say what can be done.

Equium A300D-16C - Windows has failed to start

I have a Toshiba Equium A300D-16C and all of a sudden it starts up and goes onto windows boot manager and says that Windows has failed to start and it wont let me do anything else.
I really dont know what to do and all my uni work is on it.
It says to put the windows installation disk but its not responding to any disks what so ever.
If anyone could help Id be grateful
Thanks

hi Lashay
guessing you have xp on this unit try to reinstall bootfiles.
seems that windows has lost some files...
this could be software or a hardware issue...
"fixboot " and "fixmbr" on recovery console should do this job.
safest way is to get a new hdd and a hdd-usb-adapter!
install operating system on the new hdd,
then connect the old hdd using the usb-adapter to the new system and transfer all user files.
not the system files or maybe you will get the same trouble again!
if there is a serious problem on the hdd its getting worse with every attemp to read the disk...

Equium A300D-16C turns on but the screen shows nothing/stays black

Hi there, I have a Toshiba Equium A300D-16C laptop.
It was fine until now...
When I press the power button, my laptop turns on but the screen remains black / off.
HDD indicator doesn't flash or anything ... ( in case this helps )
I've also tried to remove the battery, hold the power button for 30s and plug the power cord back in... Same thing laptop turns on but screen is black.
I tried to connect my laptop to my PC's monitor using HDMI cable but no success... Laptop turned on but my pc's monitor was showing nothing.
I haven't changed anything inside my laptop or unscrewed it.
PS:
I quite often kept my laptop on the bed/pillow so it may have something to do with overheating or something.
How did I get to this point:
Yesterday my laptop was fine, there was nothing wrong with it... I switched it off at night but when I tried to switch it back on this morning that's where I faced this problem.
Any help would be appreciated.
Many thanks,
Rejanu.

Hello
> I tried to connect my laptop to my PC's monitor using HDMI cable but no success... Laptop turned on but my pc's monitor was showing nothing.
Its very good that you have this test with an external monitor because so you could make sure its not related to internal monitor and its working properly.
Well, you have tried a lot so my personal opinion is its a serious hardware malfunction It could be related to mainboard or CPU in my opinion
I think such hardware diagnostic can only be done from an authorized service provider. I think you should contact the guys. They can help you to get rid of this problem :)

Equium A300D-16C - Switches itself off after 3 seconds

I have a Toshiba Equium A300D-16C that will not start up. When you switch it on it begins to start but within 3 seconds switches itself off before it even gets to any type of screen. It then automatically tries to switch on again, then repeats the same cycle of auto off, auto on over and over.
When you put your ear to the bottom of the laptop you can hear the system starting up then you get two very quiet beeps before it switches itself off. Does anyone know what the cause could be or if there is a fix or should i just accept that my laptop of just under two years has died and given up the ghost?
Thanks in advance for any feedback.

> How much would i be looking at to replace cpu/motherboard (not beign a tech wizard in the slightest)
I don't know exactly what is wrong with it as it should be tested before making any conclusion. But the most possible reason is the motherboard - southbridge or power circuit controller. If it's motherboard issue, you will have to pay pretty good money :( as the most expensive part of your laptop. (about 35$-40% from total new laptop price). Don't know even if it's worthy to replace it due to high price. But before, you should contact the Asp (service center):
http://eu.computers.toshiba-europe.com/innovation/generic/ASP_SUPPORT/
Ask them what really happened to it and make decision, then, replace or not.

Strange sound behaviour on Equium A300D-16C

This isn't so much of a problem, just a bit of an annoyance at times really. The sound's working fine on my Equium A300D-16C (sound card and driver all fine on the Device Manager etc. etc., buttons working fine), but, the sound level (volume) keeps changing. I first noticed it as I'd installed the sounds add-on for MS Office 2007, but wasn't always getting sounds, but then other times I was getting very loud sounds, and others very quiet sounds.
I'm +fairly+ sure I'm not accidentally touching any shortcut keys (at least the lit up quick access ones above the keyboard I'm not, but are there any other shortcuts for sound?), but for instance last night at one point I noticed the volume was set at 16, but then half an hour or so later it was 4, and then this morning when I booted it up the volume level was at 0 (but not muted).
As I said, it's not particularly a problem, because if I need to I just adjust the volume to what I want it to, but it's just been puzzling me these last few days as to what might be causing it.

Ah! //Slaps head and goes to hide under a rock// :-D I guess that'd be the one on the front that obviously rests against my slightly rounded middle...? (I am in shape - round's a shape! ;-))
It never even occurred to me that there'd be a dial somewhere! Duh!
Thanks for clearing that up. :)
//crawls under rock//
Message was edited by: BlissC

Equium A300D-16C. not booting after shutdown.

Please, this is a problem i seem not to understand. I have been using my Equium A300d-16c laptop without no problem for over a year until yesterday's evening. i was installing a software(nokia PC suite) which prompted for a restart. the shutting down was normal and for it to restart was a problem. it displays nothing but a blank screen. It is evident it does not boot as when i press the power button it goes of immediately. Only the power indicator is on. Another thing i notice is that the DVD-ROM reads any disc put inside but there is no display of any sort.
My first reaction was that it may be overheating, so i cleaned the cooling vents and blew away dusts from all compartments. but still the problem persists. Please i seek to know what may be the problem before taking it to for repairs. Help Needed. Thanks.
Message was edited by: Tobyjoe_2

Thanks. There is nothing displayed on the screen. it does not seem to boot into anything, as the powere goes off immediately when the power button is pressed. I have tried to change the ram modules, but still the same problem. i dont know what kind of hardware failure could cause this as it was working fine untill the shutdown. Thanks for the concern.

Re: Dvd drive stopped working on my Equium A300D-16C

Hi I need help!
My Equium A300D-16C has stopped recognizing any type of disc, Ive tried double clicking on the drive but they gey kicked out and the message "please insert a disc into the drive" appears.
Having read back previous posts in a bit not to look too much like a dumb blonde and have so far checked the registry values - which are not set, uninstalled the drive via the system device - to no avail. Only had it about 2 months and really cannot be without it.
Any help would be very much appreciated

I tried to install a bluetooth dongle on vista , the bluetooth device was an old one and i dont think it was compatible with vista as it didnt work and it knocked off my webcam,i uninstalled the bluetooth and re-installed the webcam driver from toshiba support, and it worked again.

MacBook Pro 13 Early 2011 Battery Degradation to Not Detected, User Replaced New Battery also Not Detected, Please Help!

I have a MBP early 2011 13 inch and do not have Apple Care. After I installed Mountain Lion I noticed the battery health was dropping pretty rapidly, with a service battery warning. I tried resetting the SMC and PRAM and even a clean install. I took it into an Apple store and they said I should have cycled it more, but I could still use it. The health dropped and dropped until a battery would not even be detected. Because Apple would not replace it for me for free and I didn't want to pay for them to do so, I bought my own battery. Once I replaced the battery with the new one, it still says there is no battery connected.
When I detach the battery and then attach it again, the battery indicator lights on the side show 4 dots. When I plugged in the MagSafe connector, the fifth light started blinking (I thought it was charging) and then it went back to all of them blinking indicating no battery detected. The computer also automatically turned on when I connected the MagSafe.
I have tired multiple times to reset PRAM and SMC even after installing the new battery to no avail. I can use the machine with the MagSafe connected, but as soon as the cord is unplugged or bumped, it goes into the emergency sleep mode.
Any thoughts on what might be ailing this not yet two year old machine? My first Mac lasted 7 years before any logic board fail so I hope that is not it. Anything I should try that I haven't yet? Any ideas on what this might cost me through Apple?
Thanks!

Why don't you look through this to insure you did everything correctly:
http://www.ifixit.com/Guide/Installing+MacBook+Pro+13-Inch+Unibody+Early+2011+Ba ttery+Replacement/5116/1
Also, where did you get this battery?

New battery is not detected on Satellite A300

Hello every body
I had this problem with my laptop Satellite A300 (PSAJ4E). I bought a new battery and started my laptop. I have Windows Vista.
The battery is not detected. When I remove the charger its work well but with indicator of low battery so Im update my BIOS but the problem is still there.
So I look around and tried to disable Microsoft in device manger.
Still not fixed properly. I removed charger and insert it again.
It shows the AC power supply but no charge.

hi king_soft,
sold a third party battery?
in some cases the used controller (battery) is not recognised by your system...
you can try this (without any promisses):
shut down notebook, remove battery, connect ac-adapter and make sure unit is powered
insert battery and wait 24hours
disconnect ac-adapter and remove battery
switch machine on to make it fully discharged (some components holding electricity)
insert battery and start the unit
check powermanager or energy options if the battery is recognised...
never open up a battery pack - it's really dangerous!
if the battery pack is recognised by the system - you won!
if not make sure that your ac-adapter supplies the right voltage/current to your system
test another battery to make sure the loading device (notebook) is working properly
if so exchange battery pack!
editing: found a info that the highest rated cpu is a Intel Celeron -M 380 (1.60GHz)
Message was edited by: Al-eX

Battery is not detected in Equium U400-124

Hi Guys,
I bought a U400-124 yesterday and replaced it today for the same model and i still have the same problem.
The notebook works fine when its conected to AC power but as soon as i unplug it the notebook dies ? Its not the charger thats the problem, i have changed that also. On the icon that tells you if the battery is charging or not it says "Battery is not detected"
Does anyone have an idea why this happens ? All help would be hugely appreciated.

Hey man
I bought a Toshiba Equium U400 too. And i faced the same problem.
So I took it to the ASP (Authorized Service Provider) and they said it was not the laptops problem it was the problem of the battery.
So as I had a warranty I changed my battery and its running great..
Try my idea and your going to be happy..
So go to a Toshiba reseller or buy your battery online.
So you did a wrong thing changing you laptop should have changed your battery... happy to help and tell me if u have any other problem.
Bye

My new battery isn't charging. My mac didn't recognize the battery even after charging it for almost 3 hours. Turns on and then turns right off even with the power plugged in so I took out the battery to type here.

Just got a new battery. I put it in and computer worked for a few minutes and shut down. I thought okay it needs to charge. Left it charging for three hours and tried turning on my computer and it came on, didn't recognize the battery and then turned off. So I have taken it out so I can type this question and ask for help. Help.
Thanks in advance!!!
nannyisme

Hi!
I think that it could be for 2 reasons: or the battery is defectuous or that's a SMC problem.
I guess that your mac is an Intel-based. So try to reset the SMC, it's explained at this page: http://support.apple.com/kb/HT3964?viewlocale=en_US.
If it doesn't work, try to update the SMC firmware, but I think that if you could use your old battery it hasn't to be necessary...

Equium A300D-16c battery has died

I purchased this laptop about 3 years ago and the battery has recently died. I tried to replace it with a non Toshiba battery that fitted the part number. This battery appeared not to work.
When I put the part in and charged it up the laptop would state that there was no battery and the battery light would flash.
However when i unplugged it the laptop would run off the battery but the laptop would still say it did not exist.
I assumed that this battery was faulty so returned it and bought a Toshiba battery which is made by Toshiba and is the same battery as my old one.
It is defiantly the same part number as my old battery however it has the same problem as the previous battery.
I updated the BIOS system when I purchased the first laptop battery so I do not think its that.
I also downloaded another battery reader programme called "Battery Care" but this also says that the battery does not exist even when I unplug and run the laptop off said battery.
The original battery that came with the laptop on purchase is still recognised but only holds charge for around 15 minutes due to age.
Does anyone have any ideas?
Thanks

Hi again
I replied earlier but for some reason it was not sent and I didnt find out until now.
Anyway what I meant was that he wanted me to use the new battery normally as in run the laptop off the battery without the ac adapter being attached. Even though the laptop would maintain that the battery was not there.
I have done this for a couple of hours before when I first got the battery and was trying to get the laptop to register its presence.
I am just worried that if I keep using the battery like that it would become a safety issue.
As the battery does work on its own and runs the computer fine its just that the laptop says there is no battery.

Re: Equium A300D-16C has died

I've had this laptop for nearly two years. But this morning its just not come back to life, and i don't know why.
The battery life has been dismal the past few months, have only been able to get about 20 minutes out of a full charge before it runs out of charge.
However, no problems other than that. I turned it on this morning, and checked emails and stuff, and the battery low icon started to glow, and the little pop up on the screen appeared, so i got my AC Adaptor and plugged it in, but it refused to charge up. I done my normal checks like, have i switched the power socket on?
Checked the lead was connected properly. All the normal things, but it's refused to charge up.
So, i shut down the laptop, unplugged everything, plugged it back in, but now it won't turn on.
The battery symbol flashes an orange red colour for a few seconds and that's it.
I rung my boyfriend to help, but he doesn't have a clue. Do i need a new battery?
Do i need a new lead? Or could it be the laptop?
Please help!
Many thanks
Eleri

Bit more detail for you :)
With the battery in the laptop, and the AC adaptor connected, when i press the on button, the battery symbol flashes orange for a few seconds and then dies. No power lead symbol or anything appears at all. That orange light is the only sign of life!
I took the battery out, and then connected the adaptor again, nothing at all happens. Its just dead.
With the battery in, and no AC adaptor, the battery icon flashes orange for a few seconds and dies again.
Im not very good with technology, so whats a motherboard?!!! Is that expensive? My warranty run out a year ago, so i don't know what to do! I love my laptop to bits! As for my pictures and documents saved on it, would i be able to retrieve them some how?
Many many many thanks!

New battery isn't detected on Equium A300D-16C

Similar Messages

Maybe you are looking for