New BUg in 645E MAX 2
Hi, I found a new bug in 645E MAX 2. When you run the FSB at 145Mhz, and boot it up, the actual frequency that it will run is 87. something... I verified this in wcpuid. On top of that, I ran the sandra benchmark and that also verified that the FSB was running slower. I change the FSB to 144 and 146, and both ran fine ehehhe...
i guess the system cant handle 145 and set itself to safe values after freezing?
Similar Messages
-
WARNING !!! the new BIOS (5.2) for 645E max U won't boot with ad
I've just tried to flash the BIOS 5.2 for the MSI 645E max U, and my computer didn't boot after that ! (I've an adaptec 29160).
I tried to reinstall windows XP, and nothing... no recognition of my hard disk, despite it is recognized in the list of bootable devices in the bios setup.
I came back to version 5.1, and all is ok now...
Hope you will fix that in the next version !Definately not the power supply .. I just tried a 350 watt and a 430 and still same issue. There's only 2 parts I haven't replaced ... the motherboard and the cpu ... so it's got to be either one of them but I don't have any xtra gear here to try :(
-
I recently purchased a 645E Max U MS-6547 MB and installed:
Northwood p4 2.4GHz proccesor,
PC2700 DDR 512 MB RAM,
geforce4 Graphics card,
Diamond Max Ultra ATA/133 120 GB 7200RPM E-IDE hard drive
My problem is that I cannot get the system to turn on at all. When I attempt to switch it on nothing happens occasionally the cpu fan will move slightly never making a even a 1/4 a roatation. I have a 350 watt Pentium 4 power supply connected to it. I know that the switch and the power supply works becuase I tried them on an old AMD system and they powered it up. The MB isn't faulty according to Googlegear, who I sent it back. They ran a diagnostic test and said it worked. I'm kinda new to this so I need all of the help I can get.I tried doing what you listed in your reply and it still wouldn't work. Then I returned it to the company I bought it from and they said the board tested fine.
I am wondering if the fact that the motherboard I have supports a SiS 645 DX chipset and I have an Intel 2.4 GHz 533 MHz Proccessor, Northwood B has anything to do withit. Or in otherwords could me not having the right chipset for my processor have anything to do withit. I am new to this but I am guessing that that will not work. If you know if that could be the reason why I am not getting any response at all from the MB please let me know. If you can also help me to figure out what chipset my proccesor is, please let me know: Spec number from Intel is SL6RZ. I am also going to need to know what MB I will need to purchase for this to work. I also have 512 MB PC 2700 DDRRAM, Ultra ATA 133 120 GB hard drive, and a Geforce 4 Video card. Thanks!! -
I'm having three problems with my 645E Max and I'm not sure if they're with the motherboard or the hard drive and NIC.
Here are the problems:
1. Occasionally when I start my computer I get a "Hard drive: Imminent failure. Backup and Replace" error message.
2. Sometimes when I boot up, my computer goes in an very long loop. It restarts itself about 20-30 times before getting into windows.
Up until this point it sounds like a HD problem... but the HD seems to be working fine otherwise.
3. The NIC sometimes doesn't seem like it's getting power (the lights on the back don't light up) when I turn it on. Restarting usually doesn't help, but moving the NIC to another PCI slot usually fixes the problem. ((It's not a bad PCI slot, since moving it from one to another, and then back to the original one also fixes the problem))
Suggestions?hehe..ok.. i had the same problem with my hdd's.
all i did was to switch places on the ide cable. fixed the problem. strange =)
1 ibm 120gxp 80 gig and 1 wd 40 gig. -
Hi there,
We're heavy users of Keynote and have noticed a new bug has recently been introduced into something that was stable. I think it has emerged in Keynote 5.2, could have been Keynote 5.1 also.
It's in the area of Set Timing and Order of each build when used on a Smartbuild. You can no longer set the Start Build field for each instance within the Smart build when the instances are interspersed between other items. The Start build field is just blank and unselectable.
To see this :
1. Create a bullet point list with 4 lines
2. Set build to Appear
3. Set "Set Timing and Order of each Build" to on
4. Create a Smart Build - set to flip
5. On the Smart Build Set "Set Timing and Order of each Build" to on
5. re-order the items in your Build Order so that they alternate between the bullet point and the smart build flip
At this point, you used to be able to set the bullets so that they Started on Click and then set the smart builds to Start with previous. This gave you a nice and very useful effect where you could click to reveal a bullet point and at the same time flip in a corresponding image. We've used this loads of times in our company presentations.
With a recent keynote update ( I think 5.2 maybe, could have been 5.1) this functinality has been lost. have tried it on Lion and Mountain Lion and it's not an OS issue, its a Keynote issue.
Could anyone from Apple acknowledge that they know the issue and suggest if it will get fixed? Right now we're hunting round for an old Keynote 9 DVD so we can install a pre build 5.2 version.
ThanksHi glennelliott72,
I've noticed the bug you describe and to me it's very irritating.
I also found some differences in the build menu between the last release and the previous one, and between the Mac OS X and iOS versions. For instance, the blast build doesn't exist anymore in Keynote 5.2 but it's still in the version for iOS 6.
What is your experience about?
I currently use OX Lion.
Thank you -
I had been using Aperture 2.1 for some time with only the usual bugs, most commonly, the Viewer screen going black or blue or red occasionally, but a new bug has appeared that is forcing me to restart Aperture frequently. After making edits, when I move on to the next image in the Browser (the thumbnail highlighting changes, as it should) the image in the Viewer does not change. I have not found a way to get a new image in the Viewer except restarting Aperture. This is greatly slowing down my processing of big projects.
Has anyone else seen this bug? Have you found a workaround beside restarting?Tony Finnerty wrote:
I had been using Aperture 2.1 for some time with only the usual bugs, most commonly, the Viewer screen going black or blue or red occasionally, but a new bug has appeared that is forcing me to restart Aperture frequently. After making edits, when I move on to the next image in the Browser (the thumbnail highlighting changes, as it should) the image in the Viewer does not change. I have not found a way to get a new image in the Viewer except restarting Aperture. This is greatly slowing down my processing of big projects.
Has anyone else seen this bug? Have you found a workaround beside restarting?
can u guys please give us a little more info? where's the aperture library located? in your main hard drive (os x) or on another drive?
are you sending the crash logs to apple?
thanx,
victor -
New bug in Ultrabeat into Logic Pro 8.0.1
Hey guys check this... a brand new bug (hope it would be only my mac, but with 8.0.0 there wasn't)
so open ultrabeat, choose the preset called Drag & drop samples under Drum Kits.
(just to use one free preset)
load a file and record something, then press play in order to listen your drum and try to load an other sample to make comparison (example: load a kick, do a 4/4 drum, try to replace the kick with an other sample and check the Preview sample in ultrabeat to try comparison... )
after this update no more Preview sample in ultrabeat voice (and than note will stop on playing when u try that function
sorry for the englishfinally i find someone else with the same prob, o already post into apple.com too
yes here the same, bug new in 8.0.1, cause on logic 8.0.0 all works fine (except some click noise when you pre-listen a file in autoloop)
however here what i can say to you (it's 3 days i'm studyng this cause i make a massive use of ultrabeat)
- no matter both power pc / intel soffer of this bug
- i try to update to leopard from my 10.4.11 (same bug) tryin a new os installation (same bug), tryn without audio card and driver (same bug)
so i really don't know how to solve it, cause there are only few people that have this problem
big mistake and big mistery -
How much money i will get, if i tell you a new bug in Firefox 8
how much money i will get, if i tell you a new bug in Firefox 8, i found a new bug in Firefox 8, i tested this bug on chrome but their is no issue with this .
About the only way you could get money is by reporting a serious or critical security vulnerability that has not been reported before.
http://www.mozilla.org/security/bug-bounty.html
http://www.mozilla.org/security/bug-bounty-faq.html -
(To Adam Winner) New bug report at data_table tag
Hi Adam
Here is a new bug in data_table
When you create an table with data_table using id=�tableName� attribute and render the data_table for the first time, JSF saves the settings, but does not change them any more when you add new Attributes.
When you add new Attributes to the data_table, they don�t get rendered. You must first change the id=�newTableName� before the changes gets rendered. Probably the tableID object is not changing its properties for some reason??
Regards:
Nermin B.Hi Adam,
Sorry for misspelling your name. I realized this after I posted the message.
We're discussing the topic of your second message - how often the model of a UIData should be retrieved - on the EG. I hope 1.0 will have a solution.
I assume you're saving the state on the server?Yes You are right. I am saving state on the server. Do you think this could be the reason for this??
But I don't follow your first message - when you wrote about "adding Attributes" to the table, what specifically were you adding, and what changes were you expecting to see?
Are these changes in your model (the object used for "value"), or something else?What I am saying is following:
Let say you create an data_table tag:
<h:data_table rowClasses="table-row-even,table-row-odd"
styleClass="table-standard"
id="msgTable"
value="#{systemMessage.activeSystemMessages}"
var="msg">
You render this. The data is displayed etc. Works just perfect.
But now you decide to add some additional attributes to your data_table let say some columnClasses
If you simply add columnClasses in the data_table above, and reload the page (without restarting server) it won�t render the new attribute (columnClasses)!!
<h:data_table rowClasses="table-row-even,table-row-odd"
columnClasses="table-column-standard,table-column-standard�
styleClass="table-standard"
id="msgTable"
value="#{systemMessage.activeSystemMessages}"
var="msg">
You must change id attribute at the data_table first before the JSF takes changes over. The code will look like this:
<h:data_table rowClasses="table-row-even,table-row-odd"
columnClasses="table-column-standard,table-column-standard�
styleClass="table-standard"
id="msgTableNEW"
value="#{systemMessage.activeSystemMessages}"
var="msg">
(See id=� msgTableNEW�)
In this case JSF will take the new columnClasses attribute and render correctly.
Regards:
Nermin B. -
I think I was cheated on the 645E Max-C
I was hoping someone could answer a question.
I just purchased a 645E Max-c (well thats what the box and all said). But when I inspected it further the motherboard had been restickered with the 645E Max-C sticker being placed over the actual board serial (which was a 645 ultra.
The only real difference between the two boards appears to be the chipsets. One of which (Northern) I can't check because it is under the heat sink. But should I assume that this chipset should have 645DX on it as opposed to the 645 that is installed in the ultra?
Secondly, on the second chipset (Southern), should it be marked as 961B and not the 961 as is in the ultra?
Could someone please advise me on this, so i can crack the shits with the supplier if he is wrong.
Regards
ACI
Quote
Originally posted by Bela
Quote
Originally posted by BiOsPhErE
Quote
Originally posted by BigConig
hmm- I've noticed a few weird things about my max-c also. If I use info-view, it shows the mainboard model as ms-6547 not MS-6547E (according to the website it should be the "E").
The same thing shows up if I use live update for the bios, MS-6547.
However, Sandra shows the chipset as 645dx and the bios shows ata133, which I don't believe was available with the 645 chipset.
from the looks of it, the max-c was a bit of a frankenstien board which has already been moved into the "archive" section in MSI's products.
Ms-6547 = Ultra
Ms-6547E= ???????????? ?( ?(
I dun think there's such mobo -
Components disarray New bug found?
I created a dashboard using among other, sliders and progress bars (Engage 2008). I exported the dashboard to power point and everything went OK. I decided to go back to the Xcelsius file, and to my astonishment, the sliders' width was now one fifth the original and the width of the progress bars was about five time wider !!
The power point file was not affected
I fixed both components widths, exported them again, went back to the original CX file....and again the same disarray!! I did this four times and the problem appeared always. Can someone tell me why is this happening?
Or is it a new bug?
Thanks!It seems very easy to mess something up on the canvas in xcelsius. Locking all the components until you need to edit one ensures you don't accidentally mess one up. Well I need to, anyway...
Also, since I started getting weird effects like losing references, components reverting to their original size when I had edited them days ago etc, I thought it was better to lock components before saving. It seems to have reduced the incidence of such behavious but I could be imagining it: I still have unexpected and quite damaging behaviour as reported elsewhere on this forum. -
I need someone to verify with me if the CPU ratio selection under the Frequency/Voltage portion of the bios is stated as locked ??
I am having an unlocked CPU, so this selection allow me to change the values from default to 0x - 15x. But when I change the CPU ratio selection to any other values other then default, the system won't boot, checking the debug LED ( 3 red and 1 yellow) meaning setting up chitset or something like that.
As for the FSB, when set to auto, it is 133Mhz. Which is correct cause this processor is actually a P4 2.4B 2.4Ghz fsb = 133.
On top of that, the default multiplier is 12x which doesn't make sense. The cpu ratio selection is also skrewed, since the range is from 0 - 15 and not 14 - 24 ??? this is really weird !!!
Regards,
Jen Sen ;(Well actually, I got it from a friend... ehhehe Where he got it is a secret... can't help you though... but if you have a 645E max 2...please check for me if the cpu ratio selection is stated as locked ?? or can you change it... or is it default ??
-
CF8 cfdocument tag has a few new bugs
This discusses two new bugs in CF8 having to do with footers
in cfdocument.
***FIRST BUG***
With CFMX7, I could define a new footer by putting a new
<cfdocumentitem type="footer"> tag in each cfdocumentsection
of my pdf report. Each could have a different string, e.g., so that
the footer could tell the reader which chapter she is reading. This
does not work in CF8. The chapter name that appears on all pages is
the one defined in the last <cfdocumentitem type="footer">
tag in the cfdocument. Now only the page number changes
dynamically. Sample code:
<cfdocument format="pdf" unit="in" pagetype="letter"
marginbottom="0.8" marginleft="1" marginright="1"
margintop="0.8"
orientation="portrait" fontembed="yes" overwrite="yes"
filename="pdfbugdemo2.pdf" pageheight="11" pagewidth="8.5"
scale="100">
<cfdocumentsection>
<cfset footerContent="1. Introduction">
<cfdocumentitem type="footer">
<div style="float: left;">
<cfoutput>#footerContent#</cfoutput>
</div>
<div style="float: right;">
<cfoutput>#cfdocument.currentpagenumber#</cfoutput>
</div>
</cfdocumentitem>
<h1>Introduction</h1>
</cfdocumentsection>
<cfdocumentsection>
<cfset footerContent="2. Body of Document">
<cfdocumentitem type="footer">
<div style="float: left;">
<cfoutput>#footerContent#</cfoutput>
</div>
<div style="float: right;">
<cfoutput>#cfdocument.currentpagenumber#</cfoutput>
</div>
</cfdocumentitem>
<h1>Body of Document</h1>
</cfdocumentsection>
</cfdocument>
*** SECOND BUG ***
In CF8, you cannot cfinclude the same template multiple times
in a given template - you get an error (at least sometimes). A
workaround is to make multiple copies of the template, each with a
different name. This was not necessary in CFMX7. Sample code:
<cfdocument format="pdf" unit="in" pagetype="letter"
marginbottom="0.8" marginleft="1" marginright="1"
margintop="0.8"
orientation="portrait" fontembed="yes" overwrite="yes"
filename="pdfbugdemo2.pdf" pageheight="11" pagewidth="8.5"
scale="100">
<cfdocumentsection>
<cfset footerContent="1. Introduction">
<cfinclude template="pdfbugfooter.cfm">
<h1>Introduction</h1>
</cfdocumentsection>
<cfdocumentsection>
<cfset footerContent="2. Body of Document">
<cfinclude template="pdfbugfooter.cfm">
<h1>Body of Document</h1>
</cfdocumentsection>
</cfdocument>
where pdfbugfooter.cfm is:
<cfdocumentitem type="footer">
<div style="float: left;">
<cfoutput>#footerContent#</cfoutput>
</div>
<div style="float: right;">
<cfoutput>#cfdocument.currentpagenumber#</cfoutput>
</div>
</cfdocumentitem>re: If you claim didn't say that,
No "if" about it - I made no such claim and never would -
thats just you
talking gibberish. Who in their right mind would say, or even
suggest, that
forums are not helpful. The only reason a forum exists in the
first place is
to be helpful!
re: So what was your actual intention in the first place?
Not sure you would undertsand, you seem to struggle to follow
along. But
just a hint for you - the forum posts, or quantity thereof,
have been used
by several people here, and by editors at sites such as
sitepoint.com, as a
metric to use to gague interest and activity. A metric only
useful when
taken in context with other pointers (job market, book
market, number of
classes still running, so on and so forth)
Again, nobody has ever said forums are not useful or helpful
- I suspect you
knew that much but felt the need to throw some nonsense about
in an attempt
at an argument - failed didn't it?
RE: Maybe they realized Ben Forta writes such a good books,
they felt
ashamed? :-)
The O'Reilly audience is typically seasoned developers, hard
core coders.
Their books are a tough read for beginners and O'Reilly
delibertately do not
cater to this audeince with many of their titles. And to put
it bluntly, the
main bunch of people to ditch CF early on were these "hard
core" types. I
belive this as the only CF developers I know are actually
more "designers"
than developers - I know of no professional coder/developers
that would
touch CF. Thats just my personal observation, btw.
re: From what I read, people are telling I'm right.
Are you crazy? They are all, at least 95%, in agreemenst that
Tim Buntel
needs to pick up the marketing act before CF dies. Seriously,
you do seem to
struggle to follow along at times - suggest you actually
read.
re: CF has always been "dead" in many places.
How can you always be dead, doesn't make sense! You have to
have lived in
order to die. There used to be hundreds of cf jobs advertised
here in
Australia every day, literally every day. Now you may see 3
or 4 each week -
mostly for migrating old cf sites to new asp.net or java
sites. And there is
no longer any CF classes advetised or held in nearly all
states - they
literally shut them down. I'm confident enough that the
comment "CF is dead"
is accurate.
r: Maybe you should be answering those questions, since you
seem to know
they're true, and I haven't heard of any such things.
I know the answers to all of those questions - becuase CF is
dying. If CF
were living, then none of those questions would have been
asked.
re: So you know they're not investing in one?
Yes, I know that. They will never spend that kind fo money on
coldfusion -
it just wouldn't be vaible for them. We're darned lucky that
still have
small team of enginners to write tags around the java
libraries and release
new versions. They are not actually going to start
"innovating" with CF in a
market like this - and I don't blame them.
"Fernis" <[email protected]> wrote in
message
news:[email protected]...
> >I never said you can't get help on the forums. Where
did you get that
> >from?
>
> If you claim didn't say that, and if you didn't even
mean that by saying
> "Forum averages about 3 new posts a day and has very
small community -
> very
> quiet.", why did you say such thing in the first place,
if it's totally
> irrelevant to all about getting help in the forums? So
what was your
> actual
> intention in the first place? Are you not reading what
other people are
> saying
> before responding? The rest of my post is really useless
compared to the
> finding that you just really do the trolling because you
like nit-picking.
> Unbelievable.
>
> >Why did O'Reilly pull their once popular CF book
from print and refuse to
> write any further CF books?
>
> Maybe they realized Ben Forta writes such a good books,
they felt ashamed?
> :-)
> I mean, if they were popular as you said.
>
> >No, its not not. Go here -
>
http://techfeed.net/blog/index.cfm/2007/8/22/Open-Letter-to-Tim-Buntel
> >- and see actual people tell you how wrong you are.
>
> From what I read, people are telling I'm right. So what
*you* say is
> downright
> silly.
>
> >But you seemed to be thing that I based my whole
argument that CF is weak
> >and
> dying
> >( is already dead in many places)
>
> CF has always been "dead" in many places. And it's been
dying for 10
> years -
> they say. So what's new? You just don't seem to
understand that random
> sites
> switching ColdFusion for something else doesn't mean
that at the same time
> there are likely new adopters of ColdFusion. You just
don't know about
> them,
> while you can more easily track if some of them go away.
You don't
> actually
> have anything but blind guesses about what's happening.
>
> I'm seeing more CF frameworks pop up as ever before. And
In Finland, I'm
> seeing more ColdFusion hosting appear than ever before.
>
> >Why did MM/Adobe pull an entire team of employees
out of Australia? Why
> >did
> >they stop printing ads in all of the trade
magazines? Why did MM push PHP
> >more than CF on their website?
>
> Maybe you should be answering those questions, since you
seem to know
> they're
> true, and I haven't heard of any such things.
>
> > Why don't they invest in an IDE to atract all those
developers out there
> that like a complete RAD platform?
> > So on and so forth???
>
> So you know they're not investing in one? And I thought
DreamWeaver would
> act
> as one? Or third party products like CFEclipse? Or
Adobe's IDE extensions
> for
> Eclipse? Sure, the CF IDE's lack behind the automation
and insight
> functionality of other IDEs, and that's something I'm
hoping for too...
> although I've always felt that strong IDEs are strictly
necessary only for
> programming languages where a huge number of
non-user-defined libraries
> and
> classes are to be referenced. The level of automation in
ColdFusion (lots
> of
> action with little code) make complex IDEs less
important than with most
> other
> languages.
>
> -Ari Ferneilus
> -
New bug of intermedia 8.1.7 for windows 2000
The bug is described as follow:
create table wzy (id varchar2(20),
ctx clob);
create index ctx_index on wzy (ctx)
parameter(...);
During I load those content into ctx column of wzy,when the length of those content is larger than 2038 byte,the system memeroy is eated up;and wher the length of those content is smaller than 2038 byte,system working is ok.
log is as follow:
C:\>ctxsrv -user CTXSYS/manager -personality M
Oracle interMedia Text: Release 8.1.7.0.0 - Production
on Sat May 12 23:40:19 20
01
(c) Copyright 2000 Oracle Corporation. All rights
reserved.
23-40-19 05/12/01 === OCO server startup ===
23-40-19 05/12/01 Initialized CORE
23-40-19 05/12/01 Connected to database.
23-40-20 05/12/01 === Initializing dispatcher ===
23-40-20 05/12/01 === Server startup completed. ===
23-40-22 05/12/01 DML batch: cid=1078
23-40-23 05/12/01 End batch, return code is 0
00-16-15 05/13/01 DML batch: cid=1078
00-16-17 05/13/01 End batch, return code is 0
00-16-49 05/13/01 DML batch: cid=1078
00-41-36 05/13/01 End batch, return code is 1
00-41-37 05/13/01 DRG-10900: out of memory
00-41-37 05/13/01 DRG-10900: out of memory
00-41-37 05/13/01 DRG-50857: oracle error in
drtldml(dml)
00-41-37 05/13/01 ORA-04030: out of process memory
when trying to allocate 65036
bytes (callheap,KQL tmpbuf)
ORA-06508: PL/SQL: could not find program unit being
called
ORA-06512: at "CTXSYS.DRUE", line 113
ORA-06512: at line 1
ORA-06510: PL/SQL: unhandled user
00-41-37 05/13/01 === Server failure ===
00-41-37 05/13/01 DRG-10900: out of memory
00-41-37 05/13/01 DRG-10900: out of memory
00-41-37 05/13/01 DRG-50857: oracle error in
drtldml(dml)
00-41-37 05/13/01 ORA-04030: out of process memory
when trying to allocate 65036
bytes (callheap,KQL tmpbuf)
ORA-06508: PL/SQL: could not find program unit being
called
ORA-06512: at "CTXSYS.DRUE", line 113
ORA-06512: at line 1
ORA-06510: PL/SQL: unhandled user
00-41-37 05/13/01 === Server shutting down ===
the need of memory requirement is up to 1G.
those error as above:
it do not appear in intermedia for solaris.
So,I think it is a new bug of intermedia for windows 2000.
Welcome to talk about the bug to me!ctxsrv is deprecated in 8.1.7 so please use ctx_ddl.index_sync() for maintaining the index.
Regarding CLOBs there is a bug with NT when the content of the CLOB contains more than 2000 chars. It should be fixed in the 8.1.7 patch release. -
Preview.app new bug : stops opening new files
Starting a couple weeks ago, perhaps with my update to iLife 09 or perhaps related to a recent system update, Preview.app has a new bug for me.
If I open a few files (jpg, pdf, etc) with Preview.app, it will mysteriously stop opening new files. Double clicking the files in Finder, using Preview->Menu->File->Open, or any "open with..." functionality causes Preview to get the focus (come forward) but the file does not open.
I am not able to make it happen consistently with any set of files, but it is not any single file causing the problem. I've had this happen every day for the last couple weeks and it is now moved from annoyance to extreme annoyance.
If I close Preview.app and restart it, the same file that would not open will open fine. I have not been able to narrow this down, but I see this in Console:
4/17/09 2:12:29 PM Fri Apr 17 Preview[11193] * -[NSCFArray insertObject:atIndex:]: attempt to insert nil
As I said, the main thing I've changed recently is installing iLife 09. I'll continue to try to create a replicatable test set, but so far it seems more mercurial than that
Anyone else seeing this?Well, let me describe it a different way. I do not believe there is any way permissions for the files I'm opening could have anything to do with this.
1) I open a jpg with preview, leave preview.app running
2) I go do something else
3) I open a PDF in firefox, it opens preview with the pdf
4) I go do something else
5) I open a jpeg with preview
6) I try to open another jpeg with preview and it does not open.
7) No file of any sort, even the same file I opened in step 1 or 5 will now open in Preview. Preview.app is now completely unable to open new files.
Generally, I leave Preview.app running. This bug makes that completely non-functional. It also means I can't use preview.app to compare images side by side because it so often won't open the images after a dozen or so files get opened during its process-life.
Message was edited by: blinc
Maybe you are looking for
-
my sound recorder is not working, with or without my headset, What's wrong with my computer?
-
Bridge crashes when viewing animation presets. How do I fix this?
When I browse animation presets in Adobe Bride, Bridge crashes. How do I fix this? Thanks for your help.
-
Will I lose existing music when downloading itunes 11?
If I download Itunes 11.1 from the apple website, will I lose all my existing music?
-
Does anyone here use Autohotkey? It helped me....Maybe you?
Ive been using Autohotkey for over a year now, and I have to say it has decreased my worktime significantly. And it might help speed up your work as well. Disclaimer: Autohotkey is a FREE scripting program. I dont own it or make money off of it. I ha
-
Ipad mini is frozen with connect to itunes picture have tried reset several times, no luck
New update for iOS, ipad froze mid stream. Has an itunes logo and connection cord picture. Cannot reset, tried reconnecting to iTunes, and it doesn't recognize the ipad. Any other ideas?