New builder: P67A G43 won't POST (I think..)

Hey all, this is my first post, and incidently I'm also building my first pc. I've run into a problem and I don't know what to do! My rig is as follows:
Mobo: MSI P67A G43
CPU: Intel Core i5 2500K
GPU: MSI N560GTX Ti
RAM: 2x4gb Corsair XMS3 (1333)
PSU: Seasonic x650
I have NOT yet installed an OS, as I havent picked one up yet.
When I turn on the computer, I get 3 SHORT beeps: the first 2 are the same pitch, the 3rd beep is higher. Right after, the "msi military class II" logo flashes on the screen. Immediately after that, I get the following message: "reboot and select proper boot device or insert boot media...etc,etc". I can enter the bios, however I have to frantically hit the DEL key after turning on the comp, and there is no screen or message that says to do so during the above process. As this is my first build, I'm not well versed on what exactly a POST screen is, or if my specific mobo even has one.
Are these beeps normal? Am I supposed to see a POST screen at some point? I am aware that MSI boards give beeps based on the number of USB devices connected, however I get the same beep code without any USB devices connected.
EDIT: Google has brought me to other threads on this same topic, and it has been suggested that memory could be an issue, or an overheating CPU. When I am in the bios there is a memory test app available, and it indicates that my RAM is fine. As well, the bios indicates that my CPU is running at 32-33C. So I don't think that either of these things is an issue, but Im new and could be completely wrong.

1.Pull out video card and RAMs and reinsert carefully, confirming it's not loose. Visually inspect CPU cooler during.
2.Check if you've connected all the power cables to MoBo and Video card. Reinsert them, to confirm tight connection.
3. don't clear CMOS so often
4. no need to manically hit Del button, just wait for the beep, and when you see the keyboard diodes flash, start pressing slowly ~ 2x pre second for example
5. are you sure about the beep code? i haven't heard different pitch beeps before
6. go into BIOS, load defaults, and check all 66 items turn off green power and other exotic enhancements for now
But seriously - all devices should be properly recognized - CPU,RAM, HDD and optics, check IDE/SATA/AHCI settings, temperatures, voltages, boot sequence, integrated peripherals, etc.
Double check CPU clock, multiplier, FSB speed, memory speed and ratio.
7. get a live Linux or Windows CD to boot up the system directly from CD
8. start Aida64 HWMonitor from USB (or what you prefer) to again confirm temps/voltages and FSB, CPU and memory speed... and RAM size/configuration properly recognized
9. Start testing system stability with Prime95 (or else), and be around to watch the temperatures
10. test video card for artifacts. I used AtiTool for mine, not sure what is good for 560GTX?
If fail, start pulling out you components -
one RAM stick out -test again
video card out - test again with Intel's GPU.

Similar Messages

P67A-G43 Won't POST

I’m at my wits end with this new build and need help, or a shoulder to cry on.
New build gives five solid beeps on POST…, no video.
Build is being done on a breadboard, so no issues with mobo shorts.
MSI P67A-G43 mobo, (times 2). (Thought first board was DOA, cross-shipped replacement.)
Intel i5-2500K didn’t work in either board, picked up an i5-2500 locally thinking the unlocked 2500K wasn’t supported with the boards’ BIOS.
Four different power supplies, using 4 or 8 pin secondary (CPU/ATX) connectors in addition to the main power connector.
Four different sticks of DDR3 1333 in every imaginable slot configuration.
Two sticks of DDR3 1666 in every possible configuration.
Two different video cards.
Reset CMOS numerous times.
Tried booting with video card out, same with RAM, no joy.
I’m stumped.
Any thoughts?

Sorry to see that one person can have so much trouble with two boards
At this point I would try my components on a known good board. Yes, I know, where to go to ? Friends, family maybe a helpful local PC store/supplier.
The likelihood of two bad boards is pretty remote, but, although it is highly unlikely, nothing is ever impossible. Its time to test everything individually by exchanging parts with a working system.
Trust that the bottle of wine might have brought some more insight along with it.

New Build 770-G45 won't post

Hi,
I doing a new build for a friend, I've built 4 systems to date but haven't had much trouble so I don't have much experience trouble shooting.
This is the issue so far, if I clear the CMOS when I boot up everything seems fine, the bios posts, I can enter setup, and everything seems to be recognized.
Once I save and re-boot I get the splash screen followed by a blinking cursor on a blank screen, in other words the bios won't post.
I'm wondering if I have a problem with my memory (see specs below), I've noticed the mainboard recognizes it as 1333, I read the sticky on memory, but I'm still not sure what to do here.
Thanks

Ram Model #F3-12800CL9D-4GBNQ
http://www.gskill.com/products.php?index=88
Looks like I should have researched this RAM more carefully, it looks like it only works for AMD 785 series and higher.
Do you guys agree?
Thanks

New build; P7N Diamond won't POST

I ran a few searches and couldn't come up with anything conclusive. Yes, I did read the sticky BIOS error codes and it didn't help. I powered on the PC for the first time, and all I get is a constant beep that never stops. Needless to say the PC doesn't POST. Anyone know what the continuous beep error code is exactly?
All connections have been verified and re-plugged to ensure proper contact. I'm questioning the processor, or the power supply. Any assistance or advice is greatly appreciated.
Specifics below:
P7N Diamond MB
PC Power & Cooling S75QB 750W EPS12V Power Supply
Intel Core 2 Duo E8400 Wolfdale 3.0GHz 6MB L2 Cache LGA 775 65W Dual-Core Processor
CORSAIR DOMINATOR 4GB (2 x 2GB) 240-Pin DDR2 SDRAM DDR2 1066 (PC2 8500) Dual Channel Kit Desktop Memory
MSI NX8800GTS 320M OC GeForce 8800GTS 320MB 320-bit GDDR3 PCI Express x16 HDCP Ready SLI Supported Video Card X 2 in a SLI configuration

Quote from: Jack the Newbie on 24-May-08, 03:20:54
Have you tested each video card seperately in the primary PCIE slot?
Have you tested each memory module seperately in all memory slots?
Did you double-check all power connections (especially 4/8-Pin +12V CPU)?
I have checked each video card in the primary slots as well as both in the other blue x16 slot. No change
I have checked each memory stick in each of the slots. No change
Quote from: Fadamor on 24-May-08, 03:56:48
The P7N Diamond uses an 8-pin +12V CPU power connector near the top-rear of the computer. I had to use an extender to get my 8-pin powersupply plug to reach.
All power connectors are indeed plugged in, the 24 pin as well as the 8pin for the CPU. THe board is laying on my desk at the moment in a bare bones config outside the case. The 8pin connector will reach, allbeit barely. I'd just like to see some output before I worry about making the inside of the case neat and tidy.
Keep the suggestions coming please. I'd rather make this work than start RMA-ing various components.

(Solved) P67A-G43 Won't OC After BIOS 5.4 (BIOS Shows OC, but CPU-Z Does Not)

After upgrading a P67A-G43 with BIOS 5.4 in preparation for a 3770k, the existing 2600k doesn't OC.
Setting the CPU ratio in BIOS shows the correct ratio in top right stats and in the ratio setting and, after disabling graphic splash, the correct multiplier is even shown on the POST. However, CPU-Z in the OS and benchmark results show only the stock 3.4.
In normal mode I tried 35, 37, 40, 44. OCG mode has the same problem. Although it show 42, CPU-Z shows only stock.
I can down-clock fine (and CPU-Z shows the correct down-clock ratio), but going above 3.4 is a non-starter.
[SOLVED]
If you disable Turbo, the core limits are not shown in the CPU settings. You have to enable Turbo, set the core limits, and then disable Turbo.

Quote
Can I just flash to the 4.1 bios using the pendrive method I used to flash to 4.2??
Yes.
> 4.1 <
Note: GD65(B3) takes the same UEFI/BIOS version.

New Build P67A-C43 B3 shuts down in 2 sec

This is a new build: (all components new)
msi P67A-C43 (B3)- mainboard
Intel Core i5 quad processor
Diablotek 550ATX power supply
GE Force GT 520 Video
8 GB DDR3 RAM
When powered up runs about 1 sec and shuts off.
Tried several suggestions... disconnected everything except CPU and 1 memory stick
Took MainBoard out of the case (Same problem)
reset CMOS (same problem)
Any new suggestions HELP !!!!

Make sure that the 4/8-Pin +12V connector for the CPU is properly plugged in.
Please check the board's CPU socket for broken or bent CPU pins.
Make sure the CPU heatsink is not fastened to tight.
Quote
Diablotek 550ATX power supply
That PSU is a piece of junk. Please try a better PSU:
http://www.amazon.com/Diablotek-550-Watt-Power-Supply-PHD550/dp/B001L0N1M2
Quote
A deceptive and potentially dangerous product
Quote
Looks good but only worked for 1 week

New Build a78m-35 wont boot/POST

Hello, I am hoping someone can help me out as I am not sure what else to try. Its a new build with the following components:
A78M-35 MB
AMD X4-760K CPU
CORSAIR CX 430
WD SATA 1TB drive
Radion Saphire GPU
I have hooked up everything like I have many times before and also re-read manual for sanity sake. I have unhooked and re-hooked everything as well, pulled MB out and re-inserted. Pulling out RAM does not offer any beeps but I am not sure if this board even has a board speaker to play beeps. Everything powers on just no output to screen and no beeps at all. Have tried just vga from integrated port with graphics card not installed as well as dvi from graphics card.
I am wondering if the bios version is not correct for this CPU? Is there a way i can tell? Is there anything else I can try?
Thank you very much in advance.

Quote from: badboy2k on 21-December-14, 03:27:25
Radeon R9-260X - 19A and a 450W psu minimum <-- you are below on the wattage by 20w
without the GPU you have no Graphics as the board has no graphics core and the board itself has non so you would have 0 output!
as for your PSU have you tried another one?
do you have another graphics card you could try on it?
No i do not have another graphics card or PSU to try on it.

P67A-G43 B3: Cannot POST--reboot loop on formerly working system--out of ideas

So I bought a computer today off of Craigslist. I demoed it before buying, running CPU and GPU benchmarks and playing a bit of Skyrim. Everything looked good. I put it in my car, drive for 10 minutes (no big bumps/turns to speak of) get it into my apartment, plug it all in and *BOOM* the computer starts for a sec and then powers down, going into a loop, doing it over and over till I hit reset. 6 hours later, I have made no progress, hoping someone here might have some suggestions.
Specs:
P67A-G43 B3 board
i5 2500k CPU
16gb GSkill DDR3 1600 Ram (2x8 gb)
Geforce gtx 480 video
Corsair 650W PSU
What I've already done:
First, I re-seated ram and video. Same issue.
Then, I tried re-seating the motherboard, took it out and screwed it back in (thinking something came loose and caused a short). No dice.
Next, I tried resetting CMOS (unplug power, hit "reset CMOS" button, took battery out for 5-10 mins, replaced). The computer boots! But, no video. No harddrive access. No nothing, other than the fans, as far as I can tell. I restart, and it's back to square one (with the infinity reboot loop). This behavior is repeatable, IE if I reset CMOS, it gets it out of the loop for one start, but there are no other changes. It doesn't constantly restart, but it's not giving me anything more than that, and the restart behavior returns as soon as I power off. In fact, if I short the Power On switch on the board to turn the power off, the system comes back on about 2 seconds later with an infinite loop. Strange.
Then, I took everything out of the box, re-assembled on a breadboard with bare minimum components. With CPU and No RAM, the behavior is the same (including the reset CMOS behavior). Ditto if I add a stick of RAM (tried it with both sticks, in a bunch of different slots, no difference) and if I add the video card in.
Additionally, I've re-seated the CPU heatsink, no effect. I've checked the pins on the CPU for any bent pins--I saw none, everything looked normal as far as I could tell. On the back, all pins look good, except for two that seemed to be touching on one of the PCI slots (this PCI slot does appear slightly bent forward on the front). I took a knife and carefully made the pins not touch, like the rest of the slots, but this seems to have had no effect.
So, I've got what should be a pretty sweet rig sitting on a cutting board right now unable to do anything. I consider myself reasonably technical, but I'm out of ideas. One thought I did have was I wondered if there was any way to upgrade BIOS with the board in such a state? Maybe by USB? Doesn't seem like I can though. Also, this system was working fine TODAY, and apparently had been working fine for a while, so wth, why now? Anyway, any help would be greatly appreciated, I'm tearing my hair out.
One additional note: the green tag on the motherboard w/ BIOS description says "E7673\IMS1A0"
Many thanks!

Since it was working fine before it got into the car and within 10 mins there's problems. I think it could be some of the power connections to the board or the PSU suddenly gone bonkers.
The reason for pointing out these two hardware is due to the fact that they have not been changed out with another similar hardware for testing yet.

Blank Screen and flashing cursor on new build-P67A GD65 (B3). Help needed.

As per the title, a computer was built for me with the following specs:
CPU: Intel Core i5 2500k
Cpu Cooler: Arctic Freezer xtreme Rev 2.0,
Motherboard: MSI P67A – GD65 (B3)
PSU: Super-Flower Amazon 550W
RAM: 4GB G.Skill RipJaws-X, DDR3, 1600
HDD: 1TB Samsung Spinpoint F3 7200rpm
Graphics Card: Sapphire Radeon HD 5850 Xtreme - 1 GB GDDR5
Disc Drive: Samsung SH-223C DVD+RW
Case: Cooler Master 690 II LITE Midi-Tower
OS: Windows 7 Ultimate
Everything went ok with the build and installation of the OS. Computer was booting ok. When I took the computer home that evening, powered it on and a blank screen with a flashing cursor on top left hand corner appeared. Tried several times but failed to boot up properly. Just to note that I can enter into the BIOS and it recognizes HDD, processor, Disk Drive and RAM. What I have done so far (of course with advice from computer experts as compared to me) are the following:
1. I removed all the parts except cpu and cooler then put them back. When I restarted a message appeared that win7 need to do a repair. It went thro the process and then it stated it can’t do repair. Did this twice. When I restarted the third time, a blank screen with the blinking cursor appeared again.
2. Cleared the BIOS using the button on the outside of the motherboard and also once using the jumpers inside the motherboard. After doing this, I pressed on the “”ON” button several times (with no power on to the computer) to dissipate any current that was left there.
3. Interchanged the RAM on different slots. Also tried using only 1 stick of Ram at a time.
4. Checked the HDD on another machine and it was ok. Formatted the HDD on the other machine, plugged onto new machine and tried to install OS again but no joy.
At this point, I’m now stuck after almost a month when the machine was built. Would it be the motherboard? RAM? etc. Just wondering if I should RMA the motherboard since it is just over a month when it was delivered.
A point to note, there is a message that comes up when it is booting stating no HDD is detected. I googled this but found out it was to do with a marvel adapter that needs to be disabled or something like that. However, it was mentioned that this wasn’t going to affect the performance of the pc as the BIOS can detect all the components.
I also noticed that when I switch on the pc, there is a small pause before it kicks on then there is a long beep followed by 2 small beeps. I presume this is normal.
Any help on this will be highly appreciated?

Quote
I also noticed that when I switch on the pc, there is a small pause before it kicks on then there is a long beep followed by 2 small beeps. I presume this is normal.
Disable EuP 2013 & that should take care of the pause. The beeps are normal at startup. Only time I have observed a blank screen & blinking cursor is if the system wasn't getting enough juice to initialize, or their was insufficient power in an OC attempt. What kind of +12V amps does that PSU you have provide?

New K8T Neo FIS2R won't post

I have looked at all the other threads in this forum, but can't find the solution.
Specs:
New K8T Neo FIS2R
New A64 3000+
New Mushkin 3500 Level One (Cas 2) 2x512MB
New Antec 550 (24A on the 12V)
ATI Radeon 9800 Pro
When I give it power, all the fans come on, the 4 LEDs on the bracket stay lit up, and then don't change, but I get no video or any other indications (such as beeps). The 4-Pin power connector, is securely connected in the proper location. The standard ATX connector is also secure. I'd link to a picture to prove it, but my camera is charging right now.
Currently I have only power wires, power switch, system speaker, video card, and 1 stick of RAM in the first slot. I have tried it without the video card, without RAM, with RAM in different slots, just about any combination I can think of. I have even cleared the CMOS a few times. Nothing changes, I always get stuck with the 4 LEDs. I don't have anything connected to the USB headers either (that was mentioned in another post).
I know some people have mentioned that the Antec 550's 24A on the 12V isn't great, but it should be more than enough amps, the way my system is setup right now.

Hi
It does not sound like a major prob, it sounds like a PSU or memory problem, anyway of checking MOBO with another PSU with at least 20A on the 12v. Also check the memory sticky at top of the posts and see if your OK memory wise, another possibility is that one of the mounting screws is tracking from the board - try removing screws and see if it boots, also check none of the cables are touching the case or MOBO.
MOBO and CPU seem fairly resilent, so faulty parts are not to likely, although one never knows. Another thought the Jbat1 Cmos jumper is on pins 1 & 2, 1 is marked on board, and you could try clearing CMOS. a corrupted bios could also cause this.
Best of luck, lets know how you go
Jocko
PS. looking at the stickys at top, Bas has put one there about a compitition by MSI, one of the questions is about Radeons needing extra power( has an April 1st entry date!!), it is worth checking, does your Radeon have its own supply, you could always remove it and see if it boots.
Cheers

P67A-GD65B3 won't post with more than 2 RAM sticks/P

Issue is as stated. On this board the dimm slots are listed as 1,2,3,4 (as marked on motherboard). The computer will consistently power cycle (not even post) when RAM is in any dual channel configuration. I've tried 4 sticks of memory (2 separate orders of 2x4GB). All RAM sticks work in non-dual channel mode. I've modified the voltage to 1.65. I've verified the timings are correct at 8-8-8-24. I've inserted 1 stick at a time, let boot all the way to windows, and inserted the next stick. I tried the inserting 1 at a time numerous different ways. Anything else I may have missed? If not, I guess its RMA time.

Quote
2 separate orders of 2x4GB
Check with G.Skill. I believe they only warranty & suggest one kit being installed. Differences in batches are noted as the excuse if memory serves me. UEFI/BIOS version 1.D was released by MSI to accomodate the non standard SPD profile programming, since a newer one, 1.E is installed, it rules a problem there out. It's also possible the RAM requires X.M.P. to be enabled to make them work correctly. Again, G.Skill is going to be the best source for advice on how to get their product to work.

MSI P67A-C43 B3 won't POST with Full RAM Installed

Hello all,
I recently purchased the MSI P67A-C43 B3 mainboard as a custom build
and have been having trouble with it. I have 16GB of ram for this board
(4x 4GB) and when I have 8GB installed (slots 1 and 3 filled), it POSTS fine.
When I fill ALL the slots for 16GB total, the board won't POST and just
power cycles ON and OFF and ON and OFF, etc...
I have replaced the memory and the PSU and am about to replace the
mainboard, but wanted to ask if anyone might have a suggestion for
troubleshooting before I do that.
Here's what I'm running on the system:
mainboard: MSI P67A-C43 B3
proc: Intel Core i7-2600K 3.4Ghz Unlocked
proc cooler: Corsair Hydro H80 CPU Liquid Cooler
ram: Corsair High Perform Vengeance 4GB DDR3 1600Mhz2x4 (4 of these)
HDD: OCZ TECHNOLOGY 120GB VERTEX PLUS SSD and Seagate 1TB LP Serial ATA HD 5900/32MB/SATA-3G
CD Drive: Sony Optiarc 24X DVDRW SATA
video: EVGA GeForce GTX 560 Ti FPB 1024MB GDDR5 PCB PCIe
PSU: Thermaltake 750W Modular Power Supply. 80+ Bronze
case: Thermaltake Chaser MK-I Full Tower Gaming Case
OS: Microsoft Windows 7 Professional 64Bit DVD
Any ideas here would be greatly appreciated! Thanks!

OK, had some time to go test your suggestions here
These are the 1.5V Vengeance RAM Modules. Tried installing 2 of the RAM on slots 2 and 4 on their own. System Boots Fine.
Went into the BIOS and changed the voltage applied to the RAM modules from
AUTO to 1.575V. On AUTO it says is applying 1.5V to the 2x 4GB modules.
Installed the full 4x RAM on all slots... and the system just shuts down. Power cycling again.
What do you think here? Bad Motherboard? Can't think of anything else to try... totally stumped!
Thanks!

P67A-G43 B3 1 long 2 short post beep

From the troubleshooting guide:
        Continues beeps or 1long 2short beeps = possible memory error
        • Try re-seating memory or test with different memory
        1long 2short or 8short beeps = possible video card problem
        • Try re-seating video card, test system with known good video card
1 Long, 2 Short       A video error has occurred and the BIOS cannot intialize the video screen to display any additional information
I am trying to use a Radeon HD 6870 with a P67A-G43 B3. Is this not possible and do I need a different motherboard?
Additional information:
This is happening during an external build test with only the CPU, Memory, and GPU installed. The CPU is a i5-2500k, the memory is Kingston 4Gx2 KHX1600C9D3K2/8G, the GPU is a Saphire Radeon HD 6870. When I plug in a monitor I get no display information.
This is the VGA test report for the motherboard: http://us.msi.com/file/test_report/TR1_2342.pdf
My GPU is not listed but when I used PCPartPicker I was under the impression that it would only pick compatible parts for my computer. It's looking like I need a different mortherboard but I would like a confirmation.

Wow I feel really stupid now. So when I used both of the 6pin power plugs I got a single post beep.
Thank you for all your help now if you have a little more time I wouldn't mind additional help.
When I start it up and successfully get the single post beep, on the monitor it says "CPU or Memory Changed !!!" and says press f1 to run setup or press f2 to load default values and continue.
is this normal?

.itl file is locked error after installing new build - iTunes won't open

After upgrading to the new build itunes won't open. I receive an error message "The iTunes Library .itl file is locked, on a locked disk, or you do not have write permission for this file." When I check permissions I have full control. I tried uninstalling all apple components - iTunes, Quicktime, apple updater - rebooting and then reinstalling but the same error message comes up when I try to start itunes.

Even after uninstalling the .itl file remained in my itunes music folder. I deleted this file after uninstalling again and then reinstalled and the issue was resolved.

New build with MSI 970A-G45 won't load OS or live CD

Motherboard: MSI 970A-G45 AM3+ AMD 970
CPU: AMD Athlon II X3 455 Rana 3.3 Ghz Socket AM3
RAM: G.Skill Sniper Series 2x4GB DDR3 1866, Model F3-14900CL9D-8GBSR
Video Card (original): ASUS ENGTX550 TI DC/DI/1GD5 GeForce GTX 550 Ti
Video Card (operational): XFX 7600 GT
System HD: Runcore 64GB Sata II SSD
Optical Drive: LITE-ON SATA DVD-RW drive
I just finished building a new upgrade build into an existing case with an existing PSU and hard drives/optical drive. Originally the system wouldn't power on at all, which I traced to the new video card (something to do with grounding or an inadequate power supply maybe?), but in any case I got past that for the moment with my old video card. The system will power on and get to the BIOS screen. I can enter the BIOS and everything looks fine: all my drives are detected, the RAM is present, the CPU looks correct. However, when I go to actually load an operating system, it never loads. After the BIOS screen I just get a blank screen with a white blinking cursor in the upper-left corner, and this never goes away (I've tried leaving it for 10 minutes or more).
Originally I was trying to boot from the mentioned SSD which has both Ubuntu 11.04 and Windows 7 64-bit partitions installed with GRUB2 to load them. This didn't load, so I tried an Ubuntu 11.04 live CD in my DVD-ROM drive. That didn't work, so I tried the same CD in an external USB CD-ROM drive in case it was a problem with the SATA controller/connectors. Still the same behavior. So I tried a memtest86+ CD in both drives. Still the same behavior. For each of the tests after the first I explicitly opened the boot menu with F11 at the BIOS screen and selected the device I wanted to try.
At this point I've already tried exchanging the memory I had originally bought with the memory I listed above, since the old memory I realized after I bought it was labelled as "Intel i5/i7 compatible" and the new memory is on the MSI support list for this motherboard model. Any thoughts on where to go next? My next thought was to RMA the motherboard but I feel like I'm flying blind here. I've never see a new build get stuck at this point in the boot process.

OK posting from Ubuntu on my now-working build!!
So, after two weeks of messing around with the CPU, RAM, video card, etc., I finally have the thought that the one thing I haven't tried yet is the old SATA expansion PCI card that I put in early on at the bottom of the motherboard underneath the video card (out of direct sight, out of mind apparently), for when I try to connect all 7 of my SATA devices. I tried pulling that out - presto, it boots. Retried a couple of times for proof, keeps booting correctly. It can even load memtest86+ off a CD. Put the PCI card back in - still boots. Reconnected the sata drive - no boot. Remembered that this particular PCI card has two SATA ports and one is for RAID of some kind, tried the other port - now it boots. The drive connected to the card is also detected by the OS.
In conclusion, it was something entirely different from what I was working on, as it usually is.
I'm going to get to work connecting everything back up, getting the new video card working, etc. I suspect I'll be back at least to read when I try to get my memory working at 1866 (different forum I know). Thanks to those who responded for the pointers.

New builder: P67A G43 won't POST (I think..)

Similar Messages

Maybe you are looking for