New folder for external hard drive?

How can I give myself permission to make a new folder on my external hard drive? Right now it is in a "You can read only" status.
Thanks, and Im new on here so I don't know if I'm posting this to the correct group.

Click on the drive, choose Get Info from the File menu, and check the format.
If it's formatted as NTFS, reformat it as MS-DOS, exFAT, or Mac OS Extended (Journaled) as desired, or install software such as Paragon NTFS on the computer.
If it's formatted as FAT32 or exFAT, use the Disk Utility's Repair Disk command on it; this may also happen for a flash drive which is about to fail.
If it's formatted as Mac OS Extended, change the permissions on that specific folder in its Get Info window.
(118000)

Similar Messages

Create new folder on external hard drive.

I am using an external hard drive with my Mac Air. How do I create a new folder on the EHD so I can sort my documents?

I double clicked on the icon (under Finder/Devices). My choices are: Open, Open Enclosing Folder, Eject Free Agent Go Flex Drive, Get Info, Remove from Sidebar. Do you have any other suggestions?
I also tried double clicking on icon, then going to File. Only choice was "New Smart Folder".

AC cords for external hard drives?

okay! everyone uses external hard drives, yes?
It's great that they connect to computers via standardized ports & cables: USB, firewire, eSATA.
but why is it that the power cords for external hard drives are completely unstandardized?
I have an external USB enclosure that I can't use because I misplaced the AC cord (my bad!)
my question: is there a chart somewhere that shows the different types of power cords for hard drive enclosures (they're the same batch of options for monitors, external CDR burners etc, optical drives etc.)
thanks
Will

I think nerowolfe was referring to the types of AC "mains" appliance power cords, specifically to the connector on the end that attaches to an AC powered device like a computer or power brick. While there are a lot of connectors used for this, there are only a few commonly used in the computer industry. The two most common are the "universal" 3 blade ones used on Mac & most PC desktops & the "figure 8" two pin ones used on many laptop power bricks, as shown below.
It would be no problem to find one of those at a Radio Shack or similar store, but as Network 23 says, most external hard drives use separate DC power supplies, & they can be fitted with one of many types of small plugs. Gumsie's advice more or less applies to these, with the following important exceptions:
• Most drives require DC, not AC power. (Thus the plus & minus polarity markings.)
• The DC power supply characteristics are not completely specified by voltage & current numbers. Some power bricks supply a well-filtered, electronically regulated voltage that doesn't vary with the current drawn from it; others a poorly filtered voltage with substantial AC "ripple" components and/or an unregulated voltage that varies from well above the rated one at zero current down to the rated voltage at the rated current. The second type is intended for devices that do not have critical voltage requirements or contain built-in filtering & regulation. They will most likely damage or cause mis-operation in voltage-sensitive devices like hard drives even if their nominal ratings are correct.
• It is not always easy to tell the two types of power bricks apart but in general the regulated types use switching supply technology & as a result are much lower in weight than the cruder ones, which use relatively heavy iron core transformers. Also, because switching supplies can easily be made that accept a wide range of mains voltages, essentially all of the "universal" power bricks rated for 100 to 220 VAC inputs use switching supplies & often are fitted with a "figure 8" type mains connector so the same brick can be sold in different countries with a mains power cord supplied with an appropriate plug for that country's wall outlets. Typically, cheap "wall wart" supplies like those sold at Radio Shack are not the regulate kind & should be used with caution with sensitive electronics. It is especially important when using them to match both current & voltage rating as closely as possible to avoid the over-voltage problem.
• A few of the more sophisticated external supplies have special features like "fold-back" current limiting. In most regulated supplies, if an over-current situation is encountered, the supply limits the current by reducing the voltage to whatever level causes its maximum rated current to be supplied. This protects the supply but not necessarily the powered device, which may be damaged by a sustained low voltage condition. (This is particularly true for electric motors.) Fold-back current limiting basically shuts down the supply until the over-current condition is corrected, which protects the powered device more completely.
• Because of all of the above, it is always safest to use the power brick furnished as original equipment with the drive or to obtain a new one as a replacement part from the vendor. If you use anything else, you do so at your own risk & you may very well damage the drive if you are unlucky enough to make a bad choice.
• A little humor to lighten this up a bit: Did you know that all electronics devices are really smoke-powered? It's true! This explains why, if you let the smoke out, they quit working!

How do I create a new folder in my hard drive - free agent go flex drive - on the mac book air?

I have just starting using a macbook air 13" and trying to sort out my folders, therefore trying to create a new folder within my hard drive, but the option is not coming up when I right click.

FORMAT TYPES
FAT32 (File Allocation Table)
Read/Write FAT32 from both native Windows and native Mac OS X.
Maximum file size: 4GB.
Maximum volume size: 2TB
You can use this format if you share the drive between Mac OS X and Windows computers and have no files larger than 4GB.
NTFS (Windows NT File System)
Read/Write NTFS from native Windows.
Read only NTFS from native Mac OS X
To Read/Write/Format NTFS from Mac OS X, here are some alternatives:
For Mac OS X 10.4 or later (32 or 64-bit), install Paragon (approx $20) (Best Choice for Lion)
Native NTFS support can be enabled in Snow Leopard and Lion, but is not advisable, due to instability.
AirPort Extreme (802.11n) and Time Capsule do not support NTFS
Maximum file size: 16 TB
Maximum volume size: 256TB
You can use this format if you routinely share a drive with multiple Windows systems.
HFS+ ((((MAC FORMAT)))) (Hierarchical File System, a.k.a. Mac OS Extended (Journaled) Don't use case-sensitive)
Read/Write HFS+ from native Mac OS X
Required for Time Machine or Carbon Copy Cloner or SuperDuper! backups of Mac internal hard drive.
To Read HFS+ (but not Write) from Windows, Install HFSExplorer
Maximum file size: 8EiB
Maximum volume size: 8EiB
You can use this format if you only use the drive with Mac OS X, or use it for backups of your Mac OS X internal drive, or if you only share it with one Windows PC (with MacDrive installed on the PC)
EXFAT (FAT64)
Supported in Mac OS X only in 10.6.5 or later.
Not all Windows versions support exFAT.
exFAT (Extended File Allocation Table)
AirPort Extreme (802.11n) and Time Capsule do not support exFAT
Maximum file size: 16 EiB
Maximum volume size: 64 ZiB
You can use this format if it is supported by all computers with which you intend to share the drive. See "disadvantages" for details.

HT1338 I was backing up my MacBook with Time Machine on my new (correctly formatted) external hard drive. It was going fine when my 2 yo knocked the hard drive. Now TM said "failed" and the Mac refuses to recognize the external hard drive. Help please?

I was backing up my MacBook with Time Machine and using my new (correctly formatted) external hard drive. All was going well when my 2 yo knocked the disk leading to a "failure" by time machine (Latest Backup: Failed). Now the MacBook will not even recognize the hard drive. I have rebooted, tried all I can think of, but no acknowledgement of the drive. The drive itself makes noise and vibrates as if working, but nothing from the Mac. Please help or $100 down the drain... Thank you.

You may have already done these resets in the "tried all I can think of " portion of your post.....if not then here they are.....
PRAM
support.apple.com/kb/HT1379
SMC
support.apple.com/kb/HT3964
.....hopefully that is all that is required.....

I put all my itunes folder on external hard drive, now I want to put it back on the mac how do i do this

put all my itunes folder on external hard drive, now I want to put it back on the mac how do i do this.

Drag the entire iTunes folder back to /Music.

Thunderbolt Dock for External Hard Drive

Hi there,
I'm trying to find a Thunderbolt Dock for External Hard Drive.
One of these http://www.topbuy.com.au/tbcart/pc/External-SATA-Hard-Drive-Docking-Station-USB- Interface-937p3180.htm
But with Thunderbolt connector instead of USB, Firewire, eSATA etc.
Do these exist?
The only thing I could find close is the Seagate Go Flexi Adapter, but that only works for those drives.
Thanks,
Grant

I would suggest this:
http://www.belkin.com/thunderbolt/
It will do more than you need and require, and you still would need to get an eSATA docking station, but that's what you really want anyways.
Thunderbolt is a bleeding edge tech still (as evidenced but the fact that nobody yet has a good dock for it) but if you go the modular approach you can still pickup your docking station with eSATA and FW800 and USB etc. and take it to a friend's and have more chance of being able to plug it in. and since you're getting a dock and not a drive you want it PC/Mac friendly because you can swap drives to ones formatted for the system. Plus this accessory will be really great if you ever get a Mac Book Air or Retina Display MB Pro that just don't have ethernet or eSATA or even firewire anymore.
And i know that tbolt is faster than eSATA natively, but if you're plugging in a SATA HD then, well i don't think i need to finish that sentance.

Importing a contact folder from external hard drive onto new iphone

It is kind of a long story...my mom was updating iphone on computer when computer crashed. iphone crashed. had friend move all info from crashed computer onto external hard drive. got new iphone.
so, she no longer has a computer and we have to share mine. she has her own itunes on an external drive and i have my own itunes on another hard drive. i got almost everything except the contacts moved back on her phone. i see the folder and contacts in a 'contact' folder on the external hard drive, but how do I move that to the new iphone without it being in outlook/google/yahoo. i tried 'adding folder' to the library containing the contacts, but that didn't work.
any suggestions? thanks!!!

thanks for the advise about the two users. so, i did that. but, now cannot seem to import the contact folder into the Address Book. the files in the 'contact'-hard drive are called CONTACT files (.contact). i don't know what that means. can i open those in the address book?

Open thread for new purchase of external hard drive

I have 4x 500 GB drives and 2x 250GB drives that I want to consolidate to one drive. I have trusted LaCie and recently (in the past 2 years) have been happy with the G-Drives as well.
To my suprise (and shock really) the Mac geniuses I spoke to at the Calgary Apple Store said their techs use the WD 500GB Passport drives all the time. Super durable etc etc. but I was in need of 2 TB. I was torn between the G-Drive and the WD My Book Studio. The difference in cost was about $70. Historically, I've had the "don't trust western digital for Macs" running through my head ever since I heard it.
However, I was convinced to go with the Western Digital My Book Studio 2TB (it's not a "new" company), but I've found that every time I boot up the drive, it runs the proprietary software which I don't intend to use. So far, I'm not finding any luck on how to get around this as I'm told it's "built into the firmware". Also, after my iMac goes to sleep, the drive disappears and I have to shut it off and turn it back on to bring it back.
What would you recommend for an external hard drive for long term storage (not to be used for time machine or iPhoto or iTunes)?
Would you recommend I take the WD drive back and get my head checked?
Purchased this:
http://store.apple.com/ca/product/TX880ZM/A?fnode=MTY1NDA0Nw&mco=MTY5NDk2NzI&s=a lpha
Was looking at this:
http://store.apple.com/ca/product/TX538VC/A?fnode=MTY1NDA0Nw&mco=MTM3NjM5NTg&s=a lpha
Thanks.
Message was edited by: Middleborn

I'd return it for something else or a refund, but that's just me.
I too was shocked upon a recent visit to an Apple Store when I saw WD external drives for sale. One salesperson told me she was shocked that they were carrying them but that other staff member had told her that the WDs were now performing well for Mac users. I don't know what to make of it.
I find the external drive market to be confusing. I'll just say that I've been happy with an Iomega 250 GB triple interface drive that I bought 4 or 5 years ago and am happy with a 1 TB OWC Mercury Elite triple interface drive that I bought a couple of months ago.
Both these drives came WITHOUT any of the proprietary software so I didn't have to face the hassle of removing any of it.
Regards,
Steve M.

Backing-up ONLY NEW ITEMS to external hard-drive

I like to stay on top of backing-up my iTunes media to my external hard-drive.
My question is how do I do this where I'm backing-up my entire library but only adding new and/or changed items to the back-up folder(i.e. backing-up ONLY new/changed data since last back-up)?
As of right now, my iTunes media folder(Primary) is 66.5GB that is stored on my "D" drive on my pc.
My back-up external drive is a Western Digital 160GB with about 45GB free space on it. While that's plenty of space for growth of my back-up files, it's not enough for me to store a 2nd NEW iTunes back-up folder which would then(after successful back-up) allow me to delete the prior back-up.
Here's another relevant question that ties in with this:
Why doesn't the following option exist right now in iTunes?;
+*File>Library>Back-up to external drive...*+
Which should also include: being able to select the drive and also tick the box for "Only back up items added or changed since last backup"
Anyone?

Forget itunes and use SyncToy from Microsoft. It does incremental changes.
http://www.microsoft.com/downloads/details.aspx?familyid=c26efa36-98e0-4ee9-a7c5 -98d0592d8c52&displaylang=en

Which format for external hard drive to use with time machine backup and connect to windows laptop?

Hi! I have an external hard drive on which I have transferred my iTunes library (just mine - not others). I have also a folder containing just films (some but not all of which are in iTunes too) Everything has been working just fine until yesterday I noticed that Time Machine was not including the external hard drive in back up as it wasn't formatted. So I have moved everything back to the Mac hard drive and and ready to format the external hard drive - but understand that if I do the contents cannot be opened from a windows laptop ... is that right? Is there are format I could choose that would allow Time Machine to back up and allow Windows to open as well (the idea being that I take the external hard drive with me on holidays etc!!) Many thanks for any advice.

ok - I understand. I have managed so far to format the drive (on windows) to exFAT file system - which apparently works with both Windows and Mac - but you're correct - it will not be included in time machine backup as I have checked the back up files and Samsung is not showing. Reckon I'm onto having to buy yet another portable hard drive just for windows - or of course buy myself a new mac book!! Can I ask you please - does the drive have to be clear of everything before I change the format - or can I change it with the files still in there? Also, got any quick ways duplicating the files onto another External Hard drive (for use on the windows laptop) At the moment the files are taking 2/3 hours + to copy over! Thank you!

Transferring playlist to new laptop from external hard drive and old laptop

I've seen similar topics before but none exactly describing my situation. I currently have itunes installed on my work laptop, but have the majority of my music on my external 120GB hard drive. When I add songs to itunes, I add them from the music folder on my external hard drive, thus the external hard drive must be plugged in to be able to play my music. However, if I import a cd it gets saved to my C drive on my work laptop under the itunes music folder and gets played from here.
I recently purchased a new personal laptop and would like to export my entire music library and all playlists from my current work laptop and external hard drive so that I would be able to have all my music in itunes on my new laptop without having to manually adding songs and changing the song info again. I worried that if I copy my itunes music folder to my new laptop it will look for the E drive (external hard drive) to play them rather than my new laptop hard drive. What's the easiest way to accomplish this task?? Please advise.
Thanks..

Hi dalbatross,
Welcome to the Support Communities!
Did you set up your new computer by creating a Time Machine backup and restoring from it?
If so, the Events and Projects that were on your internal Macintosh HD would copied to your new computer.
Here is another way to copy the events & projects to the new computer from the external drive:
iMovie Help: Work with multiple libraries
http://help.apple.com/imovie/mac/10.0/#mov3fa25bae7
Copy or move projects, events, or clips between libraries or hard disks
Connect a hard disk that contains the target library to your computer, or copy the target library to your computer.
Choose File > Open Library, and choose an option from the submenu.You can choose from recently opened libraries at the top of the submenu, locate an existing library on your computer, or create a new library.
The selected library is opened in the Libraries list, with the first event selected and its contents displayed in the browser.
In the Libraries list, select the event that contains the item you want to move or copy.
In the browser, select the item you want to move or copy.Note: To select multiple items, hold down the Command key as you click the items you want to select, or drag a selection rectangle around the items.
Do one of the following:
To move items between events or libraries: Drag the clip or project to another event or library.
To copy items between events or libraries: Option-drag the clip or project to another event or library by first starting to drag and then holding down the Option key as you drag.
Cheers,
- Judy

Moving Song folder to external Hard drive

I'm new to Logic Express, and just starting my initial setup. What's the smartest way to move all my song folders to an external hard drive. I tried just dragging and dropping it which moved the folder, but when I try to save any new work it doesn't automatically like to the external drive. Sorry for the silly question I'm just getting started.
Thanks

Hi Sheba,
Welcome to the forum!
Save as a Project!
It moves all data from the session to the new location.
Also in new sessions remeber to route the audio path
to the external HD.
best regards,
Jorge

HT4527 I transeferred my itunes to a new computer via external hard drive, however over 4000 plus songs have a ! mark beside it and they cannt be played as itunes states that the location can not be found. how do i fix this so all my music can be played.

Hi
I recently moved my itunes to a new computer by using a external hard drive.
However my itunes music is not all playable. over 4000 songs have a ! mark and when tried to be played or copied to ipod or iphone, it says that this song cannot be found and asks to locate it.
How do i fix this problem so that all my songs are available in itunes

It is probably best to start over. These are two possible approaches that will normally work to move an existing library to a new computer.
Method 1
Backup the library with this User Tip.
Deauthorize the old computer if you no longer want to access protected content on it.
Restore the backup to your new computer using the same tool used to back it up.
Keep your backup up-to-date in future.
Method 2
Connect the two computers to the same network. Share your <User's Music> folder from the old computer and copy the entire iTunes library folder into the <User's Music> folder on the new one. Again, deauthorize the old computer if no longer required.
Both methods should give the new computer a working clone of the library that was on the old one. As far as iTunes is concerned this is still the "home" library for your devices so you shouldn't have any issues with iTunes wanting to erase and reload.
I'd recommend method 1 since it establishes an ongoing backup for your library.
If you have an iOS device that syncs with contact & calendar data on your computer you should migrate this information too. If that isn't possible create a dummy entry of each type in your new profile and iTunes should offer to merge the existing data from the device into the computer, otherwise the danger is that it will wipe the information from the device.
If your media folder has been split out from the main iTunes folder you may need to do some preparatory work to make it easier to move. See make a split library portable.
Should you be in the unfortunate position where you are no longer able to access your original library, or a backup of it, then see Recover your iTunes library from your iPod or iOS device for advice on how to set up your devices with a new library with the maximum preservation of data. If you don't have any Apple devices then see HT2519 - Downloading past purchases from the App Store, iBookstore, and iTunes Store.
tt2

New computer with external hard drive...

Current setup has iTunes Library, all files, located on an external hard drive....I'm going to implement a new laptop shortly, and will download the latest version on iTunes when I set it up.....
I'll have the destination for music point to that external hard drive...
Do I have to do something with that XML file with the new iTunes before importing all the music back into iTunes?? Also, is there something I'll need to do per the iPod software with the new laptop? or should it be smooth when I plug my iPod in for the first time into the new lapop?? Any further things I need to be aware of?
THANKS.

Actually Hudgie, I'm posing another closely related question for you. I read with interest your reply to BuePod. I recently moved and added some new app's to my PC. After re-attaching all of my USB devices, I couldnt' sync my IPOD, so I reset, I downloaded new versions of IPOD and ITUNES software, did a restart, and now I have no music at all on my IPOD, and no playlists in ITUNES. What I do have is this; my ext hard drive (H) has a folder I called "Dave's ITUNES MUSIC LIBRARY" which has all of my actual music files in it. Then I also have the following files/folders on that same external H Drive:
itunes music library.itl
itunes 4 music library.itl
itunes music library.xml
Then in my "C" local drive on my laptop PC the only APPLE related folders/files I have within the "my music" folder are:
ITUNES, which in turn contains:
itunes music
itunes music library.itl
itunes music library.xml
I've made sure that ITUNES preferences is pointed to the H drive, to DAVE'S ITUNES MUSIC LIBRARY. But apparently that may be a mistake. I may have inadvertently deleted a file or folder in my C drive under "my music." But the fact remains that my ITUNES cannot seem to find or connect to my music library on my H drive.
Can you point me in the right direction. Unfortunately, apple support wouldn't even help me as they consider this external hard drive on an XP platform "non standard" and will not even offer advice.
Thanks in advance!

New folder for external hard drive?

Similar Messages

Maybe you are looking for