New G5, 2nd hard drive question

My new G5 comes in a few days, I ordered it with only one 250gb HDD. I have a second, smaller HDD I plan to install and I had the idea to run the OS from the second smaller HDD for safety reasons.
Is there anything special I should do, just a clean install of Tiger to the newly formatted smaller HDD, then direct Tiger to boot from that HDD. And should I leave the OS on the larger HDD?
thanks!!

for grins, I installed a second HD of the same size as the original.
I have a few externals that were ATA and extras. I installed them in firewire boxes and they are great for storing stuff and using mobile.
but to your question.
format and install and install all the extra applications you have will be fine.
just time consuming.
so install Tiger, then after you reboot, let the Migration Assistant move all your stuff over. very little of your reg codes will be needed when you do it, it's almost but not quite 100%. your docs etc will make the migration.
can't remember if your iTunes folder makes it.. but that should be a no brainer.
then after you have it all up and running, set the preferences>>startup to the new drive and you're golden.
for backup purposes, my drives are equal so i just clone at night every few days. this works with drives of different sizes until you run out of room on one.
luck with it.

Similar Messages

2nd hard drive questions MBP 2011

First and foremost, I want to say thanks to everyone who's been a help... Got my [now] secondary 2011 MBP running smoothly without the fans blaring or the SSD read/write time slowing down insanely.
So backstory, When I bought an SSD, for a couple bucks I also picked up a hard drive mount to replace a somewhat functioning optical drive. I did replace that, and I just put my old HDD in its place. The old HDD brings up a couple of issues.
1. I am fairly certain the old HDD is going to fail soon
2. It's "loud." After getting used to an SSD on my new macbook, as well as an SSD on this old one I am typing on now, the HDD is relatively loud in quiet environments.
3. It's battery use. I am well over the 1000 cycle recommended for MBPs but the battery is still holding a good charge, maybe not as efficient, but it works well. But, I did notice shorter battery life with the 2nd hdd.
I was able to somewhat fix 2 and 3 by going into terminal and having the HDD stop spinning after 1 minute.
TLDR:
Which brings me to my questions:
1.What HDD is recommended for quiet performance (and would be faster than my 5400 rpm drive with 40 mb/s read/write speeds in real world tests)?
2. Would an SSD be recommended? I mean the optical drive is sata 2 so there will be a bottle neck.
3. If I went the SSD route, how would I enable trim on the secondary drive? or will the trim support from my main drive transfer over? (I simply downloaded trim enabler rather than going into terminal to enable trim).
4. low price is always a bonus.
BONUS QUESTION:
So on my old HDD i had MS office 2011. It isn't working with maverick and I lost the install CD. Any ideas?

6 g/sec SSD or a 6G/sec mechanical hard drive.
If SSD then go to OWC and purchase it. Then you will not need Trim Enabler. Purchase most any other SSD and you'll need Trim Enabler. Any modern mechanical drive will work although much slower than SSD but you obviously are used to it.

New Mac Pro Hard Drive Question

So I think I understand this whole external parts thing with the Mac Pro. But I do have one question I want to make sure I am not making a mistake on. I got an external hard drive for my Mac Pro using USB 3.0. My thinking was a mechanical hard drive can only transfer data at a certain speed and it appeared that no matter which I picked Thunderbolt ($200) or USB 3.0 ($100) the transfer rate of the data was the same. If buying a SSD I could understand buying thunderbolt but for your typical external 7200 RPM hard drive isn't 3.0 all you need? Am I missing something here, i.e. why would someone pay an extra $100 for a thunderbolt external hard drive that is mechanical and 7200 RPM?

Linc Davis is quite right.
But be careful not to generalize that too much. The new cylinder Mac Pro has enough USB bandwidth available to run one USB-3 both directions at once, full tilt. So when you get more than a handful of USB drives or intend to use it for production at high throughput, it may start to slow down.

How do I get my Firefox bookmarks off of my old hard drive (now installed on my new computer as the 2nd hard drive) and into my new installation of Firefox on my new computer?

I had a lovely computer, about 8 years old, running Windows XP; the mother board died; the hard drive was fine.
I now have a new computer, running Windows 7, and I have the old hard drive as my 2nd hard drive.
How do I get my old Firefox bookmarks off the old hard drive and into my new Firefox installation?

You can find your current profile using about:support pasted into the location bar then click on "Open Containing folder. That is where you will want to replace your old files into.
Next find your old profile on your old HD, see
:https://support.mozilla.com/questions/886839
With Firefox down replace the profile files you decide to replace.
You might get a better idea of what you are doing or might want from also looking at
* http://kb.mozillazine.org/Profile_folder
* http://kb.mozillazine.org/Profile_folder_-_Firefox

Can I add a 2nd Hard Drive to my new Pavilion dv6 notebook?

I would like to add a 2nd hard drive (preferably SSD) to my "HP Pavilion dv6-6188ca Entertainment Notebook PC"
I am hoping there is an option to at least replace the DVD drive with a hard drive caddy?
What are my options?
Thanks!

stevefromapo wrote:
I purchased a OWC DataDoubler kit with a 750GB hd and it works fine. I just need to get a USB CD Drive for mac so if i need to reinstall my OS I can do it.
You could put your install disc on a USB Flash drive with Disk Utility. Also, here is the USB optical drive enclosure I bought. He raised the price a few bucks. Mine ran $10.00 with the shipping.
17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G HD + OCZ Vertex 3 SSD Boot HD 

Help. Can I go to a 1TB 2nd hard drive in my HP Pavilion dv8000 (also listed as a dv8333cl ?)

hello-
I have an HP dv8000 notebook computer running windows xp-sp2. I upgraded my 2nd hard drive (not the windows xp/boot drive - just document/family photo & video storage) to a Hitachi 320 GB drive 4 years ago. it works great but I"m almost out of space.
item/specs - 320GB 5400 RPM 8MB Cache 2.5" SATA 3.0Gb/s
http://www.newegg.com/Product/Product.aspx?Item=N82E16822145227
I would like to change it out for a newer Hitachi 1TB drive - as I am now approaching a full drive for photos,videos,docs.
such as this one - 1TB 5400 RPM 8MB Cache 2.5" SATA 6.0Gb/s
http://www.newegg.com/Product/Product.aspx?Item=N82E16822145584
It is listed as having a speed of 6.0 gb/s instead of 3.0 gb/s and It says it's 'Advanced Format'. Any reason my windows xp-sp2 laptop won't be able to use this drive?
In searching around the web it seems that my version of windows xp with sp2 as well as my bios may be the controlling factors. In entering my product number on the HP Software and Drivers page it indicates my bios is up to date (only available update is for an AMD processor). I may update to SP3 - though further research indicates XP with SP2 has no trouble 'seeing' a 1TB drive.
This compatibility doc from Hitachi that mentions these drives are compatible with some HP DV computers - but not mine specifically (dv8000 or dv8333cl) - and it also lists my motherboard/chipset as being compatible - Intel 945PM Express (I'm not sure about the express part but I'm pretty sure I have the Intel 945PM).
http://www.hgst.com/tech/techlib.nsf/techdocs/5E27D1BA34214ECB8825797B00282A2F/$file/TS5K1000_Compat...
If not the Hitachi - due to the Advanced Format issue - how about a seagate or western digital 1TB drive such as:
http://www.newegg.com/Product/Product.aspx?Item=N82E16822178006
http://www.newegg.com/Product/Product.aspx?Item=N82E16822136927
I'm running windows xp with SP2 - it's very stable, my dv8000/8333cl is a centrino dual core intel 1.83ghz, i've upgraded to 2GB of Ram installed, Also I just recovered from a 'black screen' by 'reflowing' (tearing down computer and heating up the Invidia GPU to 350 degrees for a bit to 'reflow' the solder connections to my motherboard) my nvidia Geforce GO 7600 GPU chip and cleaned/re-engineered the heat sink with custom copper heat shims - so my HP laptop is running great and I want to keep it going for a long time.
What are the downsides to popping in a 1TB secondary drive to see if it will be 'seen' and if I can partition and format it for use as my storage drive? Any thoughts? Thanks much!

Seems like my 32 bit windows xp will recognize and use up to 3-3.5GB of the 4GB of RAM. And since memory is pretty cheap now I'm going to try this also.
Anyone have any success going beyond the stated 2GB max for memory?
My Intel 945 PM motherboard/chipset lists max memory as 4GB - so it will only be limited by the 32 bit windows xp?
Thanks for any thoughts.

How do I set Catalogue to new larger internal hard drive and then delete the files from the smaller

I have just had a new 1TB internal hard drive installed in my PC and then the original smaller internal 500GB hard drive cloned onto it. The new 1TB is now Local Dick C and the smaller 500GB has been changed from C and is now Local Disk F. PSE11 is running from the new C and all my pictures are on both C and F but the catalogue is pointing to F. I want to delete all of the old files on F to free up space since they are all cloned to the new 1TB C, so I want the PSE11 catalogue to point only to the pictures on C. I have tried creating a new Catalogue and importing my pictures from C. The images come in and look connected to C but, when I close PSE11 and then reopen that new catalogue, the image path reads F, as does the original catalogue. So, now I have two catalogues apparently point to F but I want to: 1) have only one catalogue pointing to C; 2) the delete catalogues pointing to F; 3) then reformat F: so I have a clean 500GB old hard drive for future expansion. Can some please help?

Grant, all I can say is that another user was having almost identical issues a month or so ago. Unfortunately I cannot find the discussion thread now but my feeling is that it never resolved satisfactorily while both drives were connected.
To save you a lot of work formatting, copying, erasing and so forth why not just unplug the SATA cable from the old drive and see if the Organizer then starts behaving nicely with the new drive. If it does then you can go the destructive route on the old drive.
Hopefully the poster who had the similar problem might read this and update us on his/her situation - if it got resolved and how.
Cheers,
Neale
Insanity is hereditary, you get it from your children
If this post or another user's post resolves the original issue, please mark the posts as correct and/or helpful accordingly. This helps other users with similar trouble get answers to their questions quicker. Thanks.

My plan to get win7 on 2nd hard drive

Hi all,
I recently bought a new 15" MPB with an apple installed 128gb SSD drive.
My plan was to install a 2nd hard drive in the DVD spot, a 500gb with a 70ish GB win7 partition. I would like to use Win 7 for screencasting for windows tutorials and for Gaming...mostly for gaming
I thought, naively, that this would be a simple boot agent setup...boy was I wrong.
I have already installed the 500gb drive in the optibay, it is working fine
I did not realize that a macbook pro cannot boot to an external drive or dvd. I could be wrong here but all my research seems to indicate that it can't...using something like refit does not fix this problem
I tried going through the boot camp setup with my external dvd drive attached through USB...did not work
also tried a USB thumb drive...no dice
I'd like to avoid having win7 on my 128gb ssd as there is limited space
my current plan is this...if it doesn't make sense or seems wrong please let me know
put the dvd drive back in
make a bootcamp partition on the sad...maybe 35gbs
install win7
if thats working ok put the hard drive back in
use win clone to clone the bootcamp win7 to the hard drive
hopefully that will work...
I'm just not sure how I'm going to partition the drive
I would like a 100gb ntfs partition for windows
and the rest partitioned mac
looks like win clone can expand the image to the larger partition
ipartition seems like it would work for this, but not sure
any ideas on how I can make a ntfs partition on the internal?
can I partition the drive with a windows machine? maybe do the 400gb as exfat?
thanks

Get http://www.virtualbox.org/
It lets you setup your own Windows virtualized disk image anywhere you like it. You'll still need to boot into Mac OS X, but it can run either seemlessly with Windows or full screen if you so desire.
As for booting externally, Mac OS X has no trouble booting on external drives on any MacBook Pro. As for Boot Camp, check with the Boot Camp forum.
https://discussions.apple.com/community/windows_software/boot_camp
Note, when using external hard drive for anything but backup, how many copies you have of information that is both on the internal and external drive.
There should be at least two separate external copies of all your data somewhere in event one fails.

I want to add 2nd hard drive to HP Pavilion dv7-7047cl laptop

Where can i purchase a mounting kit and cable ( hard drive to mother board) to mount and hook up the 2nd hard drive?
Thanks for your time,
Cheers,
Rob

Rob422 wrote:
Where can i purchase a mounting kit and cable ( hard drive to mother board) to mount and hook up the 2nd hard drive?
Thanks for your time,
Cheers,
Rob
Hi,
This one should be fine: http://www.ebay.co.uk/itm/NEW-REPLACEMENT-HP-DV7T-Secondary-Hard-Drive-Caddy-Cable-DV7-7000-DV7T-700...
Dv6-7000 /Full HD/Core i5-3360M/GF 650M/Corsair 8GB/Intel 7260AC/Samsung Pro 256GB
Testing - HP 15-p000
HP Touchpad provided by HP
Currently on Debian Wheeze
*Please, help other users with the same issue by marking your solved topics as "Accept as Solution"*

How to add a 2nd hard drive to HP Pavilion DV7!

How to add a 2nd hard drive to HP Pavilion DV7-3165DX, product # WA794UA or WA794UAR.
(1) Order HDD, hard drive, hardware kit. HDD hardware kit includes mounting rails, static shield, screws, rubber isolators, and SATA to motherboard cable. Check your model & Product # for compatibility.
HP Parts HDD hardware kit 517639-001 for DV7-3165DX product# WA794UA and WA794UAR.
(2) Consult Drives - Windows 7 PDF, table of contents, 7 Replacing a drive in the secondary hard drive bay. This will show you how to install a 2nd HDD in a HP DV7.
Drives - Windows 7 PDF
(3) In Windows 7 select Computer, Select the HDD installed, Format (if not already formatted).
(4) If HDD does not show up in Windows 7 under Computer, go to Start (Menu), Search Programs and Files, enter "Computer Management", select Storage, Disk Management (Local), look for the Bay 2 HDD (should show up as Disc 1, Bay 1 HDD should show as Disc 0), Format the 2nd HDD (The one you just installed).
Update: I have the 2nd HDD (WD 1TB) installed, Windows now recognises it after completing the steps I mentioned in step 4, Format with default allocation NTFS 931.51GB free, 118MB used for formatting. Format with default allocation exFAT 931.51GB free, 1MB used for formatting. I selected NTFS format to reduce file fragmenting.
This question was solved.
View Solution.

When i added my 2nd HDD I was ready to get it ordered and shipped, so it would arrive before I arrived home. I also was not sure if it would be offered anywhere else and be 100% compatible. The quality of the factory HP part is good. Since then I found a cheeper source. Newmodeus DV7-3xxx Hard Drive Caddy $27.95 +tax +shipping. Not sure if the quality is the same. If this helps you, post your results and kudos.

2nd hard drive for HP Pavilion dv7t-4000 CTO Notebook - What do I need?

Hi, I have the HP Pavilion dv7t-4000 CTO Select Edition Entertainment Notebook (Product # WV703AV). It has room for two harddrives but only came with one. What would I need in order to install the second hard drive? Would I need just a connecting cable or do I also need caddy or kit?
Also, could I get a solid state? Would my notebook support that or does it only use regular ones?
Currently, I'm running Windows 7 64bit. I've got a 500GB hd (which came partitioned with hp tools/recovery).
Any help with what I would need for a traditional hdd or ssd would be greatly appreciated. I tried to look through other people's posts first, but couldn't find anything specific to my model. Thanks for your time!
This question was solved.
View Solution.

Hi:
The only place I know of where you can get a 2nd hard drive kit is from this vendor.
http://www.newmodeus.com/shop/index.php?main_page=product_info&products_id=345
Your notebook should be able to work with a SSD but I cannot guarantee it.
I really don't see any point in adding a SSD unless you make it the primary hard drive, and in order to do that, you would need to get a SSD the same size as the original 500 GB hard drive to use the recovery disks to reinstall the operating system.
Most folks get smaller SSD's and they use the W7 product key to activate a plain installation of W7.
If you can read all 25 characters of your windows 7 product key you can make your own installation media and use that to install Windows on a smaller than 500 GB SSD.
If you can read the 25 character Microsoft windows 7 product key, you can download plain Windows 7 ISO files to burn to a DVD for the version of windows that came installed on your PC, and that is listed on the Microsoft COA sticker on your PC's case.
Burn the ISO using the Burn ISO option on your DVD burning program and burn at the slowest possible speed your program will allow. This will create a bootable DVD.
Or use the Windows 7 USB/DVD installation tool to compile the ISO file you download from Digital River. Link below. You need a 4 GB flash drive to use the USB method of compilation.
http://download.cnet.com/Windows-7-USB-DVD-Download-Tool/3000-18513_4-10972600.html
Use the 25 character product key on the PC to activate the installation.
The key will activate either a 32 or 64 bit installation.
Then go to the PC's support and driver page to install the drivers you need.
Link to the W7 ISO file downloads is below.
http://www.mydigitallife.info/official-windows-7-sp1-iso-from-digital-river/

Looking for a 2nd hard drive on DV9700

I want to add a 2nd hard drive to my HP dv9728ca. Are there any specs I should look for? Right now I have a 160GB hd, and the manual ( http://h10032.www1.hp.com/ctg/Manual/c01295898.pdf ) seems to indicate my only choices are 120GB or 160GB. According to the service manual, if I want a 200GB or 250GB, I can't use my 160GB anymore. The possible options are as follows : 250x2 (5400), 200x2 (4200), 160x2 (5400), 160+120 (5400), 120x2 (5400 or 7200, but both the same). Now I've upgraded computers before, even built some from scratch, and I've never seen this type of requirement. Is this for real? I've read a post from someone saying he had trouble with his new drive which was bigger than his original one. What about the 1.5GB/sec vs 3.0GB/sec? My understanding is that the 3.0 is downward compatible, but some seem to pretend you have to set a jumper on the drive to bring it down to 1.5. Any help would be appreciated. And what if I add a 7200rpm drive instead of 5400rpm? I don't see how these should cause any trouble, but from looking around it seems HP motherboards are very specific as to what they'll let you do. I already purchased the caddy kit, all I need is the hard drive, but I don't want to end up with one that's not compatible.
If anyone's added an additional hard drive to a dv9700 series laptop, please let me know what model you chose (brand, capacity vs what you had, 5400/7200, 8MB/16MB).

Hi, I have dv9730ca laptop myself and I have 2 160GB seagate 5400rpm 8MB hdd's, they have an external data transfer rate of 300MB/sec and an internal data transfer rate of 1.1GB/sec. They do get up to around 55oC (i use cpuid - hwmonitor to check this out) and I have heard using the 7200rpm hdd's can increase the heat output so I would recommend using the 5400rpm hdd's instead. The best way I have found to get over the heat issue from any laptop is to use a targus chillmat, it has 2 fans and runs off a usb port. I hope this info helps you out
HP Pavilion DV9730CA - AMD Turion 64 X2 TL-64 2200MHz, 2GB (2x1024MB) SODIMM RAM, 320GB (2x160GB) Seagate 5400rpm HDD's, nVidia GeForce 8400 GS Graphics, Broadcom ABG Draft N Wireless, HD DVD SuperMulti DL DVD+RW, 4 USB 2.0, S Video, VGA, HDMI, Firewire, 5 in 1 card reader, RJ-45, RJ-11, Expansion Port 3, Expresscard 34/52.

WinXP dual boot Solaris on 2nd hard drive problem...

Hi there ppl,
run into a bit of a prob with dual booting winxp and solaris. I have WinXP on 1st hard drive and Solaris on 2nd hard drive 2 (Solaris - partition 1 with slice 0 x86 active, DOS - partition 2 for installing linux later, DOS - partition 3 for fat32 file storage later).
I want to boot to Solaris on drive 2 from the WinXP boot loader on drive 1. Could somebody please tell me exactly how to do this as I've copied the bootsect.sun file from Solaris via floppy to the WinXP C:\ drive, and edited the WinXP boot loader to:
[boot loader]
timeout=30
default=multi(0)disk(0)rdisk(0)partition(1)\WINDOWS
[operating systems]
multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Microsoft Windows XP Professional" /noexecute=optin /fastdetect
multi(0)disk(0)rdisk(1)partition(1)C:\bootsect.sun="Solaris/x86"
and when I select to boot to Solaris I get:
Windows could not start because the following is missing or corrupt:
<Windows root>\system32\hal.dll
Please reinstall a copy of the above file
WinXP still boots ok.
Any help would be much appreciated, thanks already.

I am having a same issue....
1.....1st 80 GB hard disk, I had window XP installed. (NTFS format)
2....add 200 GB, 2nd hard drive, make 3 partitions, on first 50GB partition I have install Solaris 10.....Having some issue with network config, but its resolve, thank this forum.....
Now, everytime when ever I need to go to Solarid, I have to go in BIOS screen and switch HD, I mean if I want to boot to solaris, I have to make a 2nd (200GB) hd primary..Soaris work fine, but from the GRUB menu, if I select window, its get hung up...
now if I want to boot to window, again I have to go to BIOS and need to switch around hdd.... make 1st (80GB) hdd primary, windows work fine....
Questions are, I do not want to go bacK & forth in BIOS.....
1....Can some one help me, provide me the step-by-step information that how can i set up dual boot, so I can use my 2nd drive (200GB) as a primary and from the GRUB, I select windows and its boot to windows... if its otherway around,,,its still ok....I don't want my kids mess up BIOS....
2...What is a chainloader+1...can some one explain?...what is +1 mean.
3....How to install GRUB in MBR?
Lion-O any ideas, how to boot windows bootloader from 2nd HD? Please step-by-step Instuctions....

How to install Solaris 10 with Win XP on 2nd Hard Drive

hi everyone,
I'm totally new to Solaris. As an enthusiast, I wants to install Solaris 10 on my Win XP PC's 2nd Hard Drive(40GB, empty) from Solaris 10 DVD.
I need help from how to format 2nd Hard Drive to how can I configure the PC so it asks me which OS to load every time.
I will highly appreciate everyone's help as I've just joined SDN. Many Thanx in advance, Jags

Happened upon this post while searching for an answer to something else and figured I would give my 2 cents on what you are trying to do so as to offer you some other ideas, as in stuff I have done personally in similar situations, just in case the other suggestions don't work out (and to avoid repartitioning your main hdd if it is your ONLY computer with an OS you have available).
Assuming you have a standard tower or mid-tower with at least 1 free 5 1/4" bay open, and if your motherboard doesn't support booting from a slave drive, and if you prefer a hardware solution so your OS installs are isolated from each other to be certain no corruption happens, like I personally do*. Then you may consider a pair of key lock internal hard drive racks (newegg search "hard drive rack ide" or sata). You would need at least 1 free 5 1/4" bay for the rack mount, then place the hard drives in their housings, each set as master, and you can stick in which ever OS drive you want, turn the key, then boot up (I recommend storing drives not in use in some large anti-static bags for protection). If you have 2 open slots, like I did on my tower, then you can connect both to the same cable and leave both in at all times. Just make sure ONLY 1 drive is keyed "on" at a time, or else you will get errors due to duplicate masters set. Also make sure you ONLY turn the keys when the system is OFF, the racks do NOT make the drives hot-swappable, it is only to offer an easier solution for using multiple hard drives on one PC so you don't have to open the case all the time and potentially damage the pins or the drives when switching them out.. Also you may need longer cables depending on the motherboard controller placement and the size of your tower, 80 wire 40pin if you are dealing with IDE (when you get longer I've noticed less 80 wire and more slower 40 wire cables). As always when dealing with the actual hardware, be extra careful, make sure power is off and PC is unplugged, touch the PC power supply if you don't have better solutions such as anti-static mat/wrist band, etc. You probably know all of this, but just making sure.
*I lost a lot of data one of the first times I tried an open source OS many years ago (some Linux distro, I forget which), I tried to repartition my windows 98 drive, it worked fine for about a week booting between the two, then most my personal windows files suddenly were random sizes and random folders ended up full of garbage files with garbage file names among other peculiar things.. If I partition a drive I generally only do it BEFORE I put data on it or install OS's.. or at least make CERTAIN that I have adequate methods for restoring my OS and personal files (such as imaging my OS install to a larger drive temporarily, etc)..
Anyway, was just offering some possible alternatives to repartitioning your main OS drive.. -TCP

I had Itunes installed on 2nd hard drive and it crashed

I had ITunes installed on 2nd hard drive and it crashed. I tried to install a new copy of ITunes and it keeps looking for the ITunes that was on the one that crashed. How do I keep ITunes install package from looking for the old install.

No reason to. I always a cloned copy of my operating systems so I can reclone it back in case the the one I use dies.

New G5, 2nd hard drive question

Similar Messages

Maybe you are looking for