New hard drive shows in Bios and device manager but not in windows explorer in windows 7

I have added a new sata 500gig hard drive and it is recognised in the bios, but is not recognised by windows explorer, though the disk is showing in device manager as a hard drive . I have followed the example on the forum by going to computer management and rescanning disks, to no avail.
Any ideas how I can get to use the drive?
My comp is a packard bell and all the details are here:- http://support.packardbell.com/uk/item/?sn=845014390330&g=1400
Hope someone can help.
Rob

Thanks Dale (and everyone else). A cure! Sorry I did not reply earlier, but have been trying all known fixes to no avail... However. The second of your links in the last reply of yours (starting, New Drive or mapped network drive) worked with a slight variation in windows7, as follows is how I achieved joy.
Right-click My Computer , and then click Manage .
Under Computer Management (Local) , click Disk Management .
This far is as above, then I'll add comments to the existing help to show my variant.
In the list of drives in the right pane, right-click the new drive and then click Change Drive Letter and Path(s) .
Here it still did not show the drive in the right window, but below it there is a second window listing disks and one of them unallocated and without a drive letter was my new drive. IMPORTANT! This set of info may not be apparent unless you enlarge the box by dragging it, as the default only shows the top box (so I have missed it until now on all my searching). Right clicking on this gave a set of obvious choices to create a choice of drive letter, format and options (NTFS etc) and this created the drive for me. I am sorry I am vague on the box choices, but on right selecting a live drive it doesn't bring up the "unallocated" box choices again. Many thanks and I hope my variant helps anyone else with a similar prob. Thanks again - Rob
Click Change , and in the drop-down box, select a drive letter for the new drive that is not assigned to a mapped network drive.
Click OK , and then click OK again.

Similar Messages

New Hard Drive, Mac partition cloned and boots fine, but I can't seem to get my BOOTCAMP (windows) partition to boot! Any ideas?

Hello all!
I got a new hard drive for my Mac Book Pro and an enclosure so I could clone the old partitions on to the new drive.
So I...
Put the new hard drive in the enclosure.
Booted up off an install disk and ran disk utility.
Copied the Mac and Bootcamp partitions over to the new drive that was connected VIA USB.
Turned off the computer, took the old hard drive out and put it in the enclosure.
Put the new hard drive in the Mac Book Pro.
Booted into Mac OSX with no problem.
When I rebooted held down the option key to boot into the windows side, it didn't show up as an option.
When I went back into the Mac side, I loaded Disk Utility and saw that I had the Mac partition, the BOOTCAMP partition, and a bunch of unallocated space. When I went into the System Preferences and set the target boot drive to the BOOTCAMP partition and restarted, I got some crazy error about there not being any bootable info on it.
That's where I am at. I have found other posts with people who are having the same problem, but I have yet to find a solution that doesn't involve me buying some 3rd party software. I know it has something to do with (what is called in Microsoft world) the Master Boot Record, but I don't know how to modify that to reflect that the BOOTCAMP partition is a bootable logical drive. I remember in MS DOS land there was some command line FDSK /something command that you would run (I think it was /MBR) to reset the MBR. To me though, all of these terms are shadowy figures in the Ether.
What do I do???
-Ricardo
p.s. I read somewhere to boot off the windows 7 disk and run the system repair tools. I tried that and no change.

I got it. It CAN be done. At least on 10.6
How I made it happen (for free) on Snow Leopard:
1) partition, dupe etc all that jazz that you know. Make the mac side work, which it seems we've all been able to do no issues. I used SuperDuper! It worked just fine. (Had it on a disk. I assume you could use any other free way of doing this.)
2) New hard drive running, I used bootcamp assistant to partition the new drive for a new Bootcamp. I don't know if it's necessary to make the new partition this way for some reason, but it's what the process ultimately included, so maybe try without, but it worked with.
3) Natively running original drive on the windows side. Used DirveImage XML to clone windows partition onto new drive connected externally.
4) Back on new hard drive running natively. (Sorry for all the switching.) You'll note that the new Bootcamp partition is NOT bootable at this point. It won't come up in the usual 'alt on startup' boot menu.
Download rEFInd and install on mac side. Technically this is freeware or w/e, but for the love of god, throw money at this man. He totally deserves it.
5) Restarting the computer, rEFInd's boot manager finally recognizes windows. But you'll find windows is a little messed up and still won't quite boot. Get out your Windows CD and pop it in. Do the 'alt boot' thing. Your boot menu options are now "EFI Manager," "Bootcamp," and "Windows Disk." Or some such. Holy Crap! It recognizes Windows!
6) Boot to the CD and tell it to repair the windows volume. It will. My computer also had to do a disk check next time I booted to Windows, which took for-stupid-ever, but eventually worked. (I went to bed in between.)
7) Everything is running smoothly. Plus, you get the rEFInd boot manager, which is also great.
Deets: I have a late 2010 MBP 13". Snow leopard/Windows 7 32-bit (long story) Moved from original 320GB seagate momentus to new 750GB Seagate Momentus XT.
Feel free to share/copy&paste this solution as you see useful. Cheers!

Zen V Plus recognized by device manager, but not by Media Explorer/Windows Media Pla

Hi,
I just got back from Best Buy after buying a Creative Zen V Plus. I installed everything from the CD and plugged in the player, but the Media Explorer doesn't recognize it (even after restarting PC). The Device Manager recognizes it but there's an exclamation mark next to it. The Windows Wizard came up numerous times asking me for permission to connect to the internet and install the driver for me, and after a while I tried doing so but it said it couldn't find anything (I would like to shave that wizard's beard off).
I went through all the stickies in the forum and about 3 different troubleshooting sessions with no luck. I googled it and asked this question on Ask Yahoo!, but no luck yet.
Here's my PC info:
Windows XP SP2
768MB Ram
Pentium 4 2.8Ghz
USB 2.0 (I tried different ports, the player does seem to be charging as there's a little lightning bolt flashing on top of the battery icon)
I'd really appreciate it if someone could help me out.
Thanks!

Ok. I checked my version of XP. It is XP Pro, Version 2002, SP2. I checked and already had the 2 hotfixes that were listed as being needed before proceeding. I followed all the steps and changed the registry key on "everyone" as the instructions stated to do. My ZVM is still not recognized by any of the software for transferring or organizing MP3's. My computer still recognizes that it is attached. It still gives me the device icon in the task bar. It still says it's A-ok in the Device Manager. It does everything, except it is not detected by ANY of my music software. <sigh>? Frustration is at its peak for me right now. I really appreciate all of the efforts. I'm at my wits end now. I have done everything you have indicated I should, but am getting the same results. I did purchase an extended warranty from Circuit City where I purchased this last summer. Is that the next step? Do I need to get this replaced?I love this player and really don't want to go through this again. We had to exchange it twice in the first month because it froze up and wouldn't do a thing. This last one has been perfect. I keep it in a leather padded case at all times. It never has the battery drained. It never gets jostled or bumped or dropped or anything that might damage it. When not being played, it stays on my desk in the case.
Thanks so much for any and all help.

Western digital 3tb 2nd hard drive shows up in device manager but not in disk manger.

Internal wd 30eurs drive shows up in device manager but not disk manager. Any suggestions on how to format this drive and partition it. I am running windows 7 64bit os

Open the Windows Control Panel and then select Device Manager which allows you to initialize and format new hard drives installed in your system.
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread. ”

After install of Lion, secondary internal hard drive used for backup and time machine is not showing on the desktop.

After an install of Lion, my secondary internal hard drive used for backup and time machine is not showing on the desktop. Cannot be located with Disk Utility either. Contains vital files! please help...

I have a TB internal drive, but this is what it shows for memory slots:
Memory Slots:
ECC:    Enabled
DIMM Riser B/DIMM 1:
Size:    2 GB
Type:    DDR2 FB-DIMM
Speed:    800 MHz
Status:    OK
Manufacturer:    0x0000
Part Number:    0x000000463732353642363145353830304600
Serial Number:    0x00000000
DIMM Riser B/DIMM 2:
Size:    2 GB
Type:    DDR2 FB-DIMM
Speed:    800 MHz
Status:    OK
Manufacturer:    0x0000
Part Number:    0x000000463732353642363145353830304600
Serial Number:    0x00000000
DIMM Riser A/DIMM 1:
Size:    1 GB
Type:    DDR2 FB-DIMM
Speed:    800 MHz
Status:    OK
Manufacturer:    0x80AD
Part Number:    0x48594D5035313241373243503844332D5335
Serial Number:    0x42076007
DIMM Riser A/DIMM 2:
Size:    1 GB
Type:    DDR2 FB-DIMM
Speed:    800 MHz
Status:    OK
Manufacturer:    0x80AD
Part Number:    0x48594D5035313241373243503844332D5335
Serial Number:    0x4207631E
DIMM Riser B/DIMM 3:
Size:    Empty
Type:    Empty
Speed:    Empty
Status:    Empty
Manufacturer:    Empty
Part Number:    Empty
Serial Number:    Empty
DIMM Riser B/DIMM 4:
Size:    Empty
Type:    Empty
Speed:    Empty
Status:    Empty
Manufacturer:    Empty
Part Number:    Empty
Serial Number:    Empty
DIMM Riser A/DIMM 3:
Size:    Empty
Type:    Empty
Speed:    Empty
Status:    Empty
Manufacturer:    Empty
Part Number:    Empty
Serial Number:    Empty
DIMM Riser A/DIMM 4:
Size:    Empty
Type:    Empty
Speed:    Empty
Status:    Empty
Manufacturer:    Empty
Part Number:    Empty
Serial Number:    Empty

Hi, I loaded Windows 7 Pro w/XP mode and iMac USB show working properly in device manager, but i cannot see a USB flash drive, or my Mac Superdrive. Does anyone have a suggestion? Thanks!

Hi, I loaded Windows 7 Pro w/XP mode and iMac USB show working properly in device manager, but i cannot see a USB flash drive, or my Mac Superdrive. Does anyone have a suggestion? Thanks!

MacDrive to provide better HFS support.
And to acces and write.

Just got new hard drive installed from apple and my old password doesn't work and it won't let me change it

just got new hard drive installed from apple and my old password doesn't work and it won't let me change it.cant install anything ,pls help,thx

Camera works. Now gotta find out about this mic thing

If I got a new hard drive on my computer and plugged in the time capsule afterwards, would I be able to recover the information from my old hard drive that was stored on the time capsule prior to the replacement?

If I got a new hard drive on my computer and plugged in the time capsule afterwards, would I be able to recover the information from my old hard drive that was stored on the time capsule prior to the replacement?

This may be of some help to you...
http://pondini.org/TM/14.html
From the FAQs Here...
http://pondini.org

Just put a new hard drive in my IMAC and I bought a lion OS license online so how do i get the software on the imac

Just put a new hard drive in my IMAC and I bought a lion OS license online so how do i get the software on the imac

You need at least 10.6.7 installed. If that's the case, since you didn't indicate anything, update to 10.6.8, launch the App Store.app in /Applications, and click on the Redeem link.

Drive appears in device manager but not in My Computer

I just wanted to post a solution that took me about 2 hrs to solve. Issue was, my firewire WD TB drive would be seen, by XP (SP3) on boot camp, in xp's device manager but not in My Computer. My goal was to format this as an NTFS drive for my boot camp files. I was unable to format this in Leopard as ntfs either. I tried installing HD drivers and formatting from leopard as FAT32 (just so Windows would see it) but all failed.
The solution I used was as below. (this would not work if you want to retain data on the drive, I didn't care as I was setting up an old drive and reformatting from scratch). Solution:
- Download free 10-day trial of Paragon's NFTS for Mac.
- Install on Leopard (note app seems sparse after download as if it didn't work) but... then...
- Open Disk Utility, you'll notice more options under Erase>Format Options drop down. Paragon acts like a plugin it seems and gives Disk Utility NTFS format options. Don't erase yet...
- Go to Partition tab, Select 1 partition and the options and select Master Boot Record and partition. (Win XP didn't see my 2nd partition when I did this so maybe it can only see the one). Anyhow create 1 big MBR partition.
- Then, go back to erase if you want and zero out.
Drive should then appear when you restart in XP.
I reformatted here from xp too just to be sure that the drive would be fully xp compatible though not sure this would be necessary.
BTW - I also had a 120GB usb drive with the same issue. For some reason with this one I was able to simply erase as FAT32 from leopard without the Paragon plugin and it showed up in XP. Go figure.

Hi Simnap,
Unfortunately Windows XP can only read hard drives that are 2 TB's or less due to barriers set in place by the age of the operating system and the hardware of that time period, even if its still used now. So you may have to partition the drive into (2) 2 TB's or (4) 1 TB's in order for XP to see it. Mac OS X supports 4 TB and above, just not XP.
Kind Regards,
Sidney S. Ramirez

App world is showing up in my applications management but not on my actual blackberry

Hi I have a blackberry bold 9780, a few months ago when I received this phone from my parents it had a blackberry app world update. Ever since I tried updating it the blackberry app world is showing up in my applications management but not on my actual blackberry (if that makes sense). I have tried unistalling and reinstalling, taking battery out to reset. Is there anything I can do to get it back as its starting to annoy me now

Hi x_cakemaker_x
Sorry One post is enough for the same issuue http://supportforums.blackberry.com/t5/Device-software-for-BlackBerry/blackberry-app-world-not-showi...
Click " Like " if you want to Thank someone.
If Problem Resolves mark the post(s) as " Solution ", so that other can make use of it.

TS1591 I have an iPod Nano generation six, and since I had a new hard drive installed in my Macbook Pro, iTunes does not recognize it. I have followed all the troubleshooting tips, many times, and nothing works. My other devices are recognized.

I have an iPod Nano generation six, and since I had to get a new hard drive on my Macbook pro, the nano no longer registers in iTunes. My other devices show up fine. I have followed all the trouble shooting advice,and nothing works.

This is the ipod touch forum

I have a G5 with a brand new hard drive,when I try and install the os I get a panic we are hanging error. What can I do to load the os

I Get a panic we are hanging error when trying to install the os on a new hard drive on a G5

Yes, the hard drive needs to be formatted and OS X must then be installed.
Drive Partition and Format
1. Boot from your OS X Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Apply button and wait until the process has completed.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Security button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
7. Quit Disk Utility and return to the installer. Proceed with the OS X installation.
It's only a lost cause when nothing else works.

If I buy a new hard drive reinstall my OS and Adobe apps, will this count as installing on 2nd comp?

If I buy a new hard drive, or format my current one and reinstall my OS and Adobe apps, will this count as installing on a 'second computer'? If so, how then do I go about ACTUALLY installing the apps on a second computer if I'm unable to 'de-register' the 'first' one because it was on an old hard drive?

TheTx,
Yes! you can simply go ahead and deactivate the product before wiping your hard drive. This would simply reset the counter back to 0 and you will be able to activate the product on the new machine as well .
Kartikay Sharma

New Hard Drive Wiped Out Photoshop and Have Tried Reinstalling but it Hasn't Worked

I have a license for photoshop CS5. I recently had a new hard drive installed on my computer. When it was installed, it wiped my photoshop off. I've tried to re-install with the disk/serial #, but the disk pops out every time I put it in. What can I do here? Any help is greatly appreciated.

download the installer and simply input your serial number during installation:
Download CS5 products

New hard drive shows in Bios and device manager but not in windows explorer in windows 7

Similar Messages

Maybe you are looking for