New hard drive won't boot!

I have an iBook, and the hard drive recently broke. First I installed os x on my external firewire hard drive, but the iBook wouldn't boot off of it (it's a maxtor onetouch drive). I got another hard drive, and using the installer (for panther), I formatted the drive, and installed os x on it. However, the iBook won't boot off of the drive. What is wrong? Is it more serious than just the hard drive?

Well I just tried to boot off of the external hard drive (which is a Maxtor Onetouch firewire drive), while I didn't have an operational hard drive. However now that the replacement drive doesn't work as well (which I am more concerned about), I am wondering whether it is a more serious issue, or not. When I took it apart, I didn't see a logic board connector as in http://www.sterpin.net/uk/ddibookg4uk.htm (picture 43). It boots the installation cd fine, so I assume that there is not a problem with the logic board? The drive I purchased was completely empty, and I am wondering whether the boot part of the partition is wrong?
In disk utilities (in the installer), it does not see the new internal drive. I have tried to start up holding the option key, but it only has a screen with two buttons, and that ticking clock as a cursor.

Similar Messages

Hard drive failure, new hard drive won't boot

Toshiba Satellite A665
I bought this laptop 14 months ago, last month the laptop refused to boot. It would say:
Isolinux disk error 05, ax4250, drive 9f
Boot failed
Often times on boot it would just show the black screen with a blinking underscore.
I tried all my known methods and nothing so I took it to a couple of shops. Both said that the hard drive was beyond repairable and not recoverable.
So I bought a new hard drive, installed it with the Toshiba recovery media. The recovery and install on new and drive went well. Had to restart, and upon restart, the original problem came up again- black screen with blinking underscore. I am unable to boot up. Any suggestions?
Thank you all

AHA, just fan issue?
Tukaine
Sep 23, 2012 10:59 PM
Since the late 2009 iMacs came out, replacing the hard drive has caused the internal Hard Drive Fan to start running at around 6000RPM.
This is due to Apple replacing the external Hard Drive temperature sensor with a proprietary firmware and using the drives internal sensor.
Replacement drives do not contain the firmware to deliver temperature data on the temperature sensor cable.
When the iMac does not receive a good signal from the hard drive it puts the fan at full speed to protect the drive.
If you replace your drive, your iMac will initially seem fine, but soon the fan will begin to speed up to full speed. Resetting the SMC (System Management Controller) will have a temporary effect, but again the fan will speed up.
Fixes people have used in the past included:
Using smcFanControl and the terminal to set a MAX speed for the fan and writing scripts to start this after every sleep/restart.
Shorting the temperature sensor cable (Not a possibility on 2011 iMacs) this tricks the iMac into thinking the drives temperature is very low, hence slow fan speed.
Both these fixes are less then perfect and leave the drive in a dangerous situation with no protection from overheating.
Another option people try is other Fan Control software. These programs will not work for this particular issue as they often only control the base speed, and if they do control the fans actual speed they rely on the temperature reported by the sensor which is now incorrect.
HDD Fan Control
HDD Fan Control works to fix this issue by reading the drives internal temperature using the S.M.A.R.T protocol and set the fans actual speed to a value good to protect the drive.
It runs at startup and continually to always control the fan correctly, prevent the loud fan noise and protect the drive from overheating
Instead of HDDFan Control, get the free SSDFan Control
http://exirion.net/ssdfanctrl/

Pavilion dv6t new hard drive won't boot after OS install

Hello, I have a HP Pavilion dv6t-3000 and the hard drive went bad and I just ordered a new one with basically the same capabilities. BIOS recognizes it because I can run the hard disk test and because the HP Recovery disc's successfully load and install on the hard drive. But once the recovery disc's finish the install and restart I get the error "No bootable device -- insert boot disk and press any key". The only thing I can think of is the hard drive is not compatible or something needs to be configured in the BIOS, but it is still recognized and still gets Windows 7 Home Premium installed using the recover disc's so in my mind that eliminates that problem.
Is there something I am missing or something else that needs to be done?
Thanks

Hi,
Locate your specific Model from the list on the link below.
http://h10025.www1.hp.com/ewfrf/wc/pfinder?cc=us&dlc=en&lc=en&tool=&query=dv6t+#N29
From here, select Software and Driver Downloads and select your OS for all the driver downloads available for your notebook.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

MAC PRO HARD DRIVE won't boot

HARD DRIVE won't boot past APPLE ICON, grey spinning wheel on grey screen. Tried using install discs, no go past the icon.
Replace small battery inside? replace chips? Logic board replace as last resort. Can't take it away from work at this point to an apple tech.
Had just installed updates to snow leopard and was successful...but went to restart it...and this crap happened.
Thanks for any help.
MT1111
< Edited by Host >

I'll try that tomorrow. Thinking it could also be:
1) The PRAMM battery. found info on that they can wear out close to 5 years. This MAC PRO is close to that now. And I use a lot of power on it.
2) MAC PRO is plugged into a SURGE PROTECTOR, instead of right into the wall outlet.
3) Been doing a lot of FORCE QUITS and HARD BOOT -- unplugging it directly when it wouldn't shut down soon enough -- lately this past year.
I just assumed that this MAC PRO with the XEON QUAD CORE etc., was a heavy duty enough NLE,
that i wouldn't have these problems. It's not fully loaded with all the chips it can carry...and I don't have near enough external terabyte hard drives for storing video and audio files to edit. I've been storing wayyy too much
on the internal hard dives and just have to stop that.
I noticed these past few days that much of the LETTERING for hard drive icons and folders' titles
were starting to look in OVERLAPPING of the lettering. That was my first hint that something was up.

Internal Hard Drive Won't Boot or Mount

I don't know if this is the right forum for this but...
My 24" iMac running 10.5.2 won't start up. Meaning I can't get past the grey screen. I fsck the disk in single user mode and got back "invalid nobe structure (4,19621)" and repairs failed, then quickly shut down. As I understand it the (4,19621) means that the file with catalog node ID 19621 in the Catalog B-Tree portion of the disk directory has an invalid extent entry. I might be wrong here. If any knows how to correct that problem that would be helpful. But thats not the real problem.
I should add I tried to boot from the install DVD and repair the disk with disk utility and it would not repair the disk either.
Disk Utility recognizes the disk as "232.9 GB AAPL Firewire Target Media" and thats all while in target disk mode.
The real problem is the disk won't mount in firewire target disk mode. I would like to try to recover some of the fills that I haven't backed up mainly in my documents folder or repair this problem.
I am going to install (well not me) a new hard drive Monday and have a fresh and new system but in the mean time I would like to try to recover some of my files if possible.
I should add the one time it did mount, all the folders were there but none of the files. And it gave no worrying. I checked the S.M.A.R.T. status and the start up volume yesterday and got the report the disks seems to be okay.
Any help in getting the disk to mount in firewire target disk mode to repair and/or recover some files would help.
Message was edited by: windylove

Thank you for the reply. That was the best and most logical reply.
DW never got to that point if thats what you are talking about nor did it get past "Inspecting disk" and Step 1: Searching entire disk in final rescue attempt". After hours of the beach ball spinning.
I am not within my apple care 3 years time frame. When they replace the hard drive tomorrow they said they might be able to recover some of my data in my Users folder.
Do you think that is possible?
That is more what I am worried about at this point. All of my important files have been back up there are just a few that weren't.
You confirmed what I was thinking. Thanks

New Hard Drive Won't Recognize My Time Machine Backup

I maxed out the space on my MacBook hard drive, so I bought a new 1TB hard drive to replace it. (I keep a TIme Machine backup of my computer on a external Passport) I installed the new hard drive, loaded up Snow Leopard and then it did the whole "Welcome" thing and asked if I wanted to set up the new hard drive. I went through the process and it asked if I wanted to transfer information to the new hard drive. I selected "transfer information from a Time Machine Backup" but when I hit "continue", it doesn't show my Passport, only "Macintosh HD". It's weird. I tried plugging the Passport into a different computer in the house, and it shows up fine.
I'm dead in the water right now. I have a new hard drive in my laptop with OS loaded on it, but no way to transfer my data from my Time Machine Backup to it! Any ideas why it won't show the Passport Drive?
Thanks - I'm really stuck right now.

Does it boot into Open Firmware with CMDOption+of ?
http://docs.info.apple.com/article.html?artnum=42642
reset-nvram (press Enter)
set-defaults (press Enter)
reset-all (press Enter)
Have you done a PRAM reset...
http://docs.info.apple.com/article.html?artnum=2238

My clone external hard drive won't boot - start up?

Hi,
I am selling my MacPro and need to clone its system drive for the new lap top I will buy soon. So I bought a new external 2TB HDD from OWC. I have found that this external HDD will not boot up, even though it says it is bootable, and appears in the Start Up prefs when I select it. It sppears on the desktop, doesn't make any weird clicking noises as well.
I am using 10.6.8 OS X. The 2TB HDD has two partitions (created with DU), one is bootable (Mac OS X extended journaled), and the other is a regular HDD space for media etc. It is GUID. It has "Ownership" checked in the info box.
I used CCC 3.4.4 and since this is 'hopefully' a one time deal, selected the 'Delete anything that doesn't exist on the source' setting. I cloned my system drive to the bootable space and had no problems with the transfer. Plenty of space to write all the files. I even made sure everything was checked in the 'source' window that a system drive might need. Everything was checked.
I spoke with a representive at the OWC Sales company and checked that this HDD can be used as a bootable drive.
I checked the connections: with external HDD with FW800, and Sata connectors. I have checked it with my Mac Book Pro as well. Same result. No boot.
I really don't understand why this drive won't boot, since everything looks correct.
Does anyone have any thoughts, suggestions, ideas for fixing this issue?
Thanks
M

Not sure if you managed to get this issue resolved yet Marcus, but I too have a similar problem:
Currently I'm upgrading from Leopard to Lion (via Snow Leopard) on both an iMac and MacBook Pro (both Intel), but before I proceed with the OSX upgrade I wanted to back everything up. Thus far I have partitioned an external firewire drive (G Drive - one that is bootable), and cloned each machine using Carbon Copy Cloner to it's own partition (both GUID). There is plenty of space left over on each partition.
The issue - I can boot the OS X from the external drive on the MacBook Pro but not on the iMac.
When I restart and hold down Option on the iMac the only drive that appears is the HDD, not the other two selectable drives that are visible if I boot up on the MacBook Pro. On the iMac in System Prefs > Startup Disc I can see all 3 drives but when I select it and restart, the machine freezes on the grey loading screen and goes no further.
Not that it should make a difference, but there is a 3rd partition on the external drive that is currently empty (for extra storage).
Any help is greatly appreciated - I can't find any relevant answers elsewhere. Thanks,
Dan

New hard drive won't recognize my iPhone

My hard drive crashed and my replacement hard drive won't recognize my iPhone. I can see all my content, but can't move or replace it. I was able to access content on my iTouch just fine and luckily synched my contacts back into my laptop, but no dice on the phone. Any ideas? BTW, my phone is a jailbroken original iPhone and I am not particularly proficient with this kind of stuff.

Does it boot into Open Firmware with CMDOption+of ?
http://docs.info.apple.com/article.html?artnum=42642
reset-nvram (press Enter)
set-defaults (press Enter)
reset-all (press Enter)
Have you done a PRAM reset...
http://docs.info.apple.com/article.html?artnum=2238

New Hard drive - won't install windows from recovery disc

I am having an issue with my Satellite L505D-S5965. I replaced the hard drive (upgraded from 250 to 500GB) due to issues with the old one (which had been replaced once already) and am using the recovery disc I made before my other hard drive crashed. When I boot the computer, it says it is loading Windows files, asks for country, etc., but then doesn't display an operating system to choose and asks me to choose drivers. I can't restore it from a system image because I kept getting an error on the old drive when I tried to create one. When I've checked, it says that Windows isn't installed on the computer. I checked the BIOS and it is recognizing the new hard drive. I have also tried booting it up from the DVD/CD using the set of disks I created after I got my new hard drive previously, but it doesn't seem to even recognize them and I can't get to the Toshiba Recovery Wizard. I would order the Toshiba Recovery Media, but with the issues I'm having, I'm not sure that is the fix. I'd hate to be out another $30 on an old computer (since we also had to replace the mother board in the past few months) if I'm not sure that will cure the problem.

Satellite L505D-S5965
Downloads here.
The usual problem is restoring to a drive with advanced-format technology. Nearly all the new drives use it. See this message from three years ago.
See this message for early installation of the driver.
Intel Rapid Storage Technology
-Jerry

New Hard Drive Won't Configure

I just bought a new Hard Drive (Crucial 256gb SSD) and physically installed it. However I am having problems configuring it. When I C or option boot and go to Diskutil and erase/partition the drive I get the same error: "POSIX reports: the operation could not be completed. Could not allocate memory. The drive shows up in my Diskutil manager and its S.M.A.R.T. status is verified." I don't know what to do, please help. Thanks

It was not your internal drive that failed or the SSD that has the problem. It is, more then likely, the cable that goes from the drive to the logic board that has failed. Replace that cable and I bet the original drive will work and you will not get that error when you try to configure and install OS X on the SSD.
I bet you have a 2009 model Macbook Pro. Is that correct? Apple used Cheap cables on that year MBP.
If you do a search you will find many have had to replace that cable.

New Hard-drive - won't reboot after restored with TM

Hey,
I got a new hard drive yesterday and used TM to restore my last back up. When I went to restart the computer it now doesn't go past the Apple and spinning gear.
I've tried to eject the CD and external hard-drive. I've restarted holding shift, then function, then cmd + alt + R + P. None of these have worked!
Help!
Thanks
Kash

KashUK wrote:
Hey,
It let me choose the HD but then it's stuck on the loading page again!
I'm not really sure what topic to look under in the trouble-shooting page. I'm not very good with computers.
Thank-you for the advice.
K
KashUK wrote:
Hey,
It let me choose the HD but then it's stuck on the loading page again!
I'm not really sure what topic to look under in the trouble-shooting page. I'm not very good with computers.
First, I guess I should ask just how you did the restore. Did you start up from your Install disc and use the +Restore System From Backup+ option in the Utilities menu, per #14 in [Time Machine - Frequently Asked Questions|http://web.me.com/pondini/Time_Machine/FAQ.html] (or use the link in *User Tips* at the top of this forum)? If not, do that.
|
Otherwise, you want #E8 in [Time Machine - Troubleshooting|http://web.me.com/pondini/Time_Machine/Troubleshooting.html]. Here's the direct link: http://web.me.com/pondini/Time_Machine/E8.html Here's the gist of it:
Why did you get a new drive? If the old one failed, it's possible it corrupted your system as it was beginning to fail, and those changes got backed-up, so were brought back when you restored.
In that case, you might want to do the restore over, but select an earlier backup, from before the troubles started. Just be sure to use your +Snow Leopard+ install disc.
If you used a Leopard Install disc to restore a +Snow Leopard+ backup, that won't work. You may want to just do it over with the +Snow Leopard+ disc, or your best bet may be to just install OSX from your Snow Leopard Install disc, then download and install the 10.6.6 "combo" update from the link there.

New hard drive won't appear as destination for software reinstall

I have a macbook I bought in 2006. My 60G hard drive was failing so I purchased a new 320G and installed it myself. The online manual had good instructions for pulling the old hard drive out and putting the new one in, but skipped the part where I apparently had to swap the protective metal cover from one to the other. I did that myself. I didn't peel any stickers off the new one.
Now I'm using my old installation disks to reinstall Mac OS X v10.4, but when the screen appears that says "Select a destination volume to install the Mac OS X softward" there's no destinations to choose from. How do I get my computer to recognize the new hard drive?

You need to initialise your new disk by "Erasing it" and choosing the "Mac OS Extended (Journaled)" format. You can do this using Disk Utility while booted from the Instal DVD, see Mac OS X 10.4: About the utilities available on the Mac OS X 10.4 Install DVD.
EDIT Adrian is obviously quicker on the draw
Message was edited by: Michael Conniff

New hard drive won't select as startup disk

I just installed a new hard drive in my 17" iMac flatpanel. I have it set as master, it comes up in Disk Utility, I erased it... again and when I tried to install from a disk, it told me I couldn't use it as the startup disk and had the stop sign with the exclamation point in it.
I was able to restore from a working image I had on my ipod, but when I did the restart, I still got the flashing folder.
Any suggestions would be great!
Chuck

Not sure how you got here. This is the discussion area for the AirPort Extreme base station (AEBS) and wireless networking. Your question has nothing to do with that at all.
You should post your question in the iMac Flat Panel discussion area.

Mail for Mac on new hard drive won't import Mail from old hd

I recently installed an additional hard drive (running Tiger), but I kept my old one (running Panther), too, to use as a backup.
After resolving a few snags, the data and apps transferred over OK, but two days ago I (very foolishly) tried to make a change in the name I use as Administrator (or at least that's what I meant to do), and all the apps on my new hard drive forgot their passwords, preferences, etc.
What a pain!
I'll eventually get all the preferences, etc., set; but Mail on the new hd also lost everything--addresses, trash, sent messages; and that's got me baffled.
My old hd still has Mail on it (including addresses, etc.), but I haven't been able to import data from it to Mail on the new hd.
In the new Mail, under the File menu, when I choose "Import Mailboxes" and select the button for Mail for Mac OS X, then navigate to Mail on my old hd, it's faint and can't be selected.
Suggestions of any kind would really be appreciated. (And from now on, I'll just live with my name being misspelled as Administrator!)
Thanks a lot,
Richard
G4 sawtooth Mac OS X (10.4.6)

Richard,
Welcome to the Discussions.
When trying to import a pre-Tiger mailbox created with Mail, use type "Other", instead of type OSX.
However, if you can replace any copy of the Mail folder on your Tiger drive, and any com.apple.mail.plist in the Preferences folder of your Tiger drive with copies from your Panther drive, Mail will open to say it is ready to import Mailboxes, and will then convert all the mailboxes at once.
However when finished, you will need to check for leftover files, that can become problematic, and to check to see if full conversion took place. See:
http://discussions.apple.com/thread.jspa?threadID=413196
and
http://discussions.apple.com/message.jspa?messageID=2039086#2039086
Ernie

New hard drive won't install in my macbook pro 13"

Hi everyone
I have recently been having problems with my mac book where I was constantly seeing the spinning beachball. I had wiped the hard drive and was still having this problem so took my mac book to a "genius" at my local mac store who told me that the hard drive was faulty. I was out of warranty so he advised me how to change the hard drive and recommended me to install a crucial 240gb M500 SATA 6Gbps 2.5 SSD. I have now fit this into my mac book and have done internet recovery to allow me to get to Disk Utility. My computer recognises the new Hard drive but when I got to erase the disk to enable me to install the operating system it just hangs attempting to unmount the hard drive. I left it over night and nothing happened. IS there something I have done wrong or is there another way of me installing the operating system onto the new hard drive?
Many thanks in advance

Hi Clinton:
off topic: remembering your beautiful 980GB M500, i want to point to two things that I came repeatedly by:
1. the M500 has more "overprovisioning" than most other Crucial ssds ( I thought that you might want to hear that.
2. Lately I hear more and more comments by respectable manufacturers that Trim in Mac OSX should be avoided: the "enabling" softwares are a bit crippled software and there are many timing faults at the file level communications, which are counterproductive.
So I followed the recent comments of a OWC staff member:
"One way to live without TRIM on OSX is just reduce the volume on the drive and leave the unallocated space...unallocated. If you have a 240GB drive I suggest removing 40GB.
The drive will map this into the over provisioning and move the space in and out of use on the volume very quickly...almost faster than TRIM does
Also remember the drives do have garbage collection and will look after themselves if given the chance too".
So I restored the complete original IOAHCIFamily.kext ( by running a Combo Update) on all my SSDs, and with DiskUtility I dragged the bottom of the startup partition up for about 40GB and left it unallocated (no format).
I remember that you did not install Trim (?), but to be sure I send this to you.
Have fun my friend,
Lex

New hard drive won't boot!

Similar Messages

Maybe you are looking for