New Hardrive and now blank screen with sleep light on
My warranty ran out on one of my mbp's, so I decided to install a new hardrive in one. I went through all the steps, and was very cautious. Now when I turn on the laptop the screen is blank and the sleep light stays on the entire time. I hear the cd-rom do some stuff but that's it. If anyone can help me figure out what happened it would be greatly appreciated.
Well problem solved, had to apply some pressure on top of the case by the left i/o and next thing you know I hear the beautiful chime
Similar Messages
-
Will a new MotherBoard cure Blank Screen with blinking cursor?
Stuck with Blank Screen with blinking cursor; ESC key couldn’t bring up Startup Menu; OS is not loading
Product Name: HP G62 237 CA Notebook PC
Short description of the problems:
--- Press ESC key couldn’t bring up Startup Menu when booting up
--- Blank screen with blinking cursor thereafter
--- Stuck here forever and OS is not loading
DETAILED INFORMATION:
Product Name and Operating System:
Model: HP G62 237 CA Notebook PC
O/S: Pre-loaded with Win 7 Home Prem
Processor: Pent. Dual-Core CPU T4500 2.30GHz
Memory: 4GB
BIOS Ver. (Insyde): F.17
System BOARD ID: 1484
Product #: WQ767UA#ABC
Product Config ID: 049C110000202710000020000
Problem History:
--- Used to have frequent BSOD (got fixed later because of faulty RAM that I suspected)
--- Window couldn’t be loaded
--- Window Repair and HP Recovery were tried but not functioning
--- OEM Hard Drive was then removed & formatted few times by using other computer
--- Hard Drive was then tested by other computer; it can be installed Win XP & Win 7
--- So, Hard Drive was eliminated from the suspect list
--- Replaced with other good RAM from other computers & put back the OEM Hard Drive to my HP G62; everything worked fine, such as: able to reinstall Win 7; listening to music files; got Internet to download latest BIOS from HP support site; connected to my 42 inched TV as my monitor; and even smoothly updated the BIOS from v.17 to v.37!
--- Also, able to receive Window Updates from the Internet; and seemed that all problems were nicely solved
--- Once I believe my system got stabilized; I went back to test the 2 supposedly problematic RAM to see whether they were both faulty or not, then the whole thing has turned around! Completely screwed me up until this moment …
--- After put back the problematic RAM, Window couldn’t be loaded …
--- With a few error messages… such as,
--- The file is possibly corrupt. The file header checksum does not match the computed checksum;
--- After the next reboot… an unexpected screen message showed up:
Intel ® Cantiga PCI Accelerated SVGA BIOS
Build Number: 1932 PC 14.34 11/11/2009 02:36:14
DECOMPILATION OR DISASSEMBLY PROHIBITED
Copyright © 2000-2003 Intel Corp. All Rights Reserved.
--- After that, OS was not loading …
--- Press ESC key couldn’t bring up the Startup Menu during boot up
--- Blank screen with blinking cursor thereafter and seems stuck here forever
Procedures performed for troubleshooting:
Tried hard reset for more than 5 times (removed battery, AC adapter disconnected and then hold down the Power button for more than 60 secs) and tried reseating memory too; same result with Blank Screen with blinking cursor after each reboot.
Connected to an external monitor [Fn + F4/F5] to see whether there was any display, nothing has showed on the external monitor, it seemed that no connection established between the two.
Finally, took the long journey to follow the Service and Maintenance Guide of HP G62 to remove the CMOS battery for well over 15 minutes and put it back. But the result was again disappointed. Tried 4 times already. The latest error message is:
The CMOS checksum is invalid. The CMOS will be reset to the default configuration and will be rebooted. Please check your BIOS Setup options to see if they change.
CMOS Reset (502)
ENTER – Reboot the system
After this message, the same Blank Screen with blinking cursor came back. And pressing the ESC key couldn’t bring up Startup Menu when booting up …
Note: the fan is still running; the Power button is functioning but seems stuck here forever!
I’ve already carefully read this HP Support document titled “HP BIOS Application Selected is Corrupt or Missing”:
http://h10010.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&dlc=en&docname=c01443485#N144
If really is the BIOS problems, then I will have the difficulties of updating a Window-based BIOS when I couldn’t even load Window!
(Note: Boot from USB has no point because right now I couldn’t change the boot sequence because the various “Startup Menu” options are not showing up!)
Secondly, I am still stuck with the Blank Screen with a blinking cursor after I passed the first screen of “Press the ESC key for Startup Menu” when re-booted again!
Thirdly, I have formatted my Hard Drive more than 3 times during the last few days for testing; I don’t have the OEM pre-loaded Win 7 with me anyone … and I don’t think I have the UEFI installed previously on my system. I did try hold down the Win Key + B with the most updated BIOS in the attached USB …, it came back with the same blank screen with a cursor blinking after reboot.
Note: the Blank Screen I’m experiencing right now is not completely black, in fact, there is background light from behind the screen and on each reboot, I can see the HP logo and the left corner message of: “Press ESC key for Startup Menu” … So, I suppose that my computer screen is not physically broken at least.
Requests:
Please explain to me that what are the problem areas and the root causes if is possible?
What steps or other tests can be done to make it work again?
Do you think replacing the entire MotherBoard can cure the Blank Screen with blinking cursor?
[Warranty: expired! I am the original purchaser & the end-user of this HP G62; acquired 2 years ago directly from a trustworthy source: staples (in Canada). Would HP Support still willing to service it for an extra charge?]
Thanks in advance for any suggestion and idea!
Owenson
===========================================Stuck with Blank Screen with blinking cursor; ESC key couldn’t bring up Startup Menu; OS is not loading
Product Name: HP G62 237 CA Notebook PC
Short description of the problems:
--- Press ESC key couldn’t bring up Startup Menu when booting up
--- Blank screen with blinking cursor thereafter
--- Stuck here forever and OS is not loading
DETAILED INFORMATION:
Product Name and Operating System:
Model: HP G62 237 CA Notebook PC
O/S: Pre-loaded with Win 7 Home Prem
Processor: Pent. Dual-Core CPU T4500 2.30GHz
Memory: 4GB
BIOS Ver. (Insyde): F.17
System BOARD ID: 1484
Product #: WQ767UA#ABC
Product Config ID: 049C110000202710000020000
Problem History:
--- Used to have frequent BSOD (got fixed later because of faulty RAM that I suspected)
--- Window couldn’t be loaded
--- Window Repair and HP Recovery were tried but not functioning
--- OEM Hard Drive was then removed & formatted few times by using other computer
--- Hard Drive was then tested by other computer; it can be installed Win XP & Win 7
--- So, Hard Drive was eliminated from the suspect list
--- Replaced with other good RAM from other computers & put back the OEM Hard Drive to my HP G62; everything worked fine, such as: able to reinstall Win 7; listening to music files; got Internet to download latest BIOS from HP support site; connected to my 42 inched TV as my monitor; and even smoothly updated the BIOS from v.17 to v.37!
--- Also, able to receive Window Updates from the Internet; and seemed that all problems were nicely solved
--- Once I believe my system got stabilized; I went back to test the 2 supposedly problematic RAM to see whether they were both faulty or not, then the whole thing has turned around! Completely screwed me up until this moment …
--- After put back the problematic RAM, Window couldn’t be loaded …
--- With a few error messages… such as,
--- The file is possibly corrupt. The file header checksum does not match the computed checksum;
--- After the next reboot… an unexpected screen message showed up:
Intel ® Cantiga PCI Accelerated SVGA BIOS
Build Number: 1932 PC 14.34 11/11/2009 02:36:14
DECOMPILATION OR DISASSEMBLY PROHIBITED
Copyright © 2000-2003 Intel Corp. All Rights Reserved.
--- After that, OS was not loading …
--- Press ESC key couldn’t bring up the Startup Menu during boot up
--- Blank screen with blinking cursor thereafter and seems stuck here forever
Procedures performed for troubleshooting:
Tried hard reset for more than 5 times (removed battery, AC adapter disconnected and then hold down the Power button for more than 60 secs) and tried reseating memory too; same result with Blank Screen with blinking cursor after each reboot.
Connected to an external monitor [Fn + F4/F5] to see whether there was any display, nothing has showed on the external monitor, it seemed that no connection established between the two.
Finally, took the long journey to follow the Service and Maintenance Guide of HP G62 to remove the CMOS battery for well over 15 minutes and put it back. But the result was again disappointed. Tried 4 times already. The latest error message is:
The CMOS checksum is invalid. The CMOS will be reset to the default configuration and will be rebooted. Please check your BIOS Setup options to see if they change.
CMOS Reset (502)
ENTER – Reboot the system
After this message, the same Blank Screen with blinking cursor came back. And pressing the ESC key couldn’t bring up Startup Menu when booting up …
Note: the fan is still running; the Power button is functioning but seems stuck here forever!
I’ve already carefully read this HP Support document titled “HP BIOS Application Selected is Corrupt or Missing”:
http://h10010.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&dlc=en&docname=c01443485#N144
If really is the BIOS problems, then I will have the difficulties of updating a Window-based BIOS when I couldn’t even load Window!
(Note: Boot from USB has no point because right now I couldn’t change the boot sequence because the various “Startup Menu” options are not showing up!)
Secondly, I am still stuck with the Blank Screen with a blinking cursor after I passed the first screen of “Press the ESC key for Startup Menu” when re-booted again!
Thirdly, I have formatted my Hard Drive more than 3 times during the last few days for testing; I don’t have the OEM pre-loaded Win 7 with me anyone … and I don’t think I have the UEFI installed previously on my system. I did try hold down the Win Key + B with the most updated BIOS in the attached USB …, it came back with the same blank screen with a cursor blinking after reboot.
Note: the Blank Screen I’m experiencing right now is not completely black, in fact, there is background light from behind the screen and on each reboot, I can see the HP logo and the left corner message of: “Press ESC key for Startup Menu” … So, I suppose that my computer screen is not physically broken at least.
Requests:
Please explain to me that what are the problem areas and the root causes if is possible?
What steps or other tests can be done to make it work again?
Do you think replacing the entire MotherBoard can cure the Blank Screen with blinking cursor?
[Warranty: expired! I am the original purchaser & the end-user of this HP G62; acquired 2 years ago directly from a trustworthy source: staples (in Canada). Would HP Support still willing to service it for an extra charge?]
Thanks in advance for any suggestion and idea!
Owenson
=========================================== -
i have a macbook that wont restart it has a white pg with a folder with a ? mark on it !!
serial # W8******YA2
<Edited By Host>Question (?) Mark, Blinking Folder, or Gray Screen at Startup
These are related but not identical issues. Their causes are outlined in Intel-based Mac- Startup sequence and error codes, symbols. Solutions may be found in:
A flashing question mark appears when you start your Mac
Mac OS X- Gray screen appears during startup
In most cases the problems may be caused by:
Problem with the computer's PRAM - See Resetting your Mac's PRAM and NVRAM.
Boot drive's directory has been corrupted - Repair with Disk Utility.
Critical system files are damaged or deleted - Reinstall OS X.
The disk drive is physically non-functional - Replace the hard drive.
Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
The main difference if you are using Lion or Mountain Lion is that you must first boot from the Recovery HD:
Boot From The Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Reinstall Snow Leopard Without Erasing The drive
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install Mac OS X 10.6.8 Update Combo v1.1.
Reinstalling Lion/Mountain Lion Without Erasing The Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless. -
my itunes will not update keeps comming up with a error when dloading the latest version now my iphone4s wont sync as it has the latest software
Is the message refering to a specific .msi file? If so, which particular .msi is it referring to? (iTunes.msi, bonjour.msi, AppleSoftwareUpdate.msi, etc.)
-
I pushed the power button and now the screen won't light up and the keyboard lights a on
Have have purchased a MacBook Air 13" and as I went to go turn the volume up, I pushed the power button instead, now the display is black and the keyboard lights are still on! I don't no what to do plez help
In OS X Mavericks behavior of the power button changed.
Power button /sleep function
http://support.apple.com/kb/HT5869
A new Mac comes with 90 days of free tech support from AppleCare.
AppleCare: 1-800-275-2273
Best. -
Hi there, ok so my ipad has been either turning off or just locking itself for sometime now but last night it turned itself off and when i tried to turn it back on it just came up with a blank screen with the back light. When i put it on the charger the sound of it charging happenes but nothing else. I hav tried resetting it but as i am not very savvy with all this stuff i thought i would get some advise before doing anything else. it anyone can help me that would be fantasic
thank youIf a reset doesn't work, try and force iPad into Recovery Mode:
1. Turn off iPad. Press and hold the Sleep/Wake button for a few seconds until the red slider appears, slide to turn off.
2. Connect USB cable to computer
3. Press and hold the Home button down and connect the docking end of cable to iPad
4. Continue holding the Home button until you see the "Connect To iTune" screen
5. Release the Home button
6. Open iTune (make sure you have the newest version of iTune)
7. You should see "iTunes has detected an iPad in recovery mode"
8. Use iTune to restore iPad
Note: You need to be patient and repeat the above many times to recover your iPad -
I used utilities to source my 10.6 snow leopard install disc to my main hardrive, and now when I turn on my computer the apple with the spinning wheel stays on the screen and stuck like that. How do I fix it Help please. I already tried all the commands such as Command R, Holding down the Option key, C and holding down shift at the start up but nothing happens.
initialy All I was trying to do was downgrade 10.7 to 10.6 .You have to consider the possibility the hard drive may be dying. If your data isn't backed up, try one of the tools below:
https://discussions.apple.com/docs/DOC-1689
Once you are sure your data is backed up, we can examine other possibilities. In the meantime call AppleCare for your original installation DVDs. You may need them. -
Having trouble with touch screen. Freezes, texting adds more letters, screen locks up. Got new phone, synced new phone and now it does the same thing??
I also tried the Hard Restart and still has the problem?
-
I have a new Dell Inspiron 15R. I closed it without shutting it down and when I tried to start it up I get a blank screen with my cursor. What's wrong.
You may get a reply here but it's best to post a question in the columns it naturally belongs to; in this case Dell forums.
-
Done restore and now it goes to blank screen with timer
Can anyone help, I have done a restore on my ipod and now it goes from the locked screen to a blank screen with the timer, wont let me do anything to it not even turn the thing off.
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
i brought a used ibook 9.2 and im tryin 2 get it 2 work but it just cumin on with a blank screen with the time showin and after a couple of mins it ask me for a user name and password how do i make it like new
couple of mins it ask me for a user name and password
Replacement System Install & Restore CD/DVDs are available from Apple's Customer Support - in the US, (800) 767-2775 - for a nominal S&H fee. You'll need to have the model and/or serial number of your Mac available.
You will need those discs to change the admin user name and password. -
New Install - startx results in blank screen with mouse cursor
I installed Arch on my desktop last week with no issues, so I wanted to install it on an old THinkpad R31. Everything with the installation went smooth, but when I try to 'startx' all I get is a blank screen with a mouse cursor that I can move around. I've installed xorg-xinit, xorg-twm, xorg-xclock, and xterm.
I'm not getting any significant errors in the logs, or even the terminal I issue 'startx' in.
I'm not sure what the problem could be...
Here is my output from 'startx'
X.Org X Server 1.13.0
Release Date: 2012-09-05
X Protocol Version 11, Revision 0
Build Operating System: Linux 3.6.0-1-ARCH i686
Current Operating System: Linux x_00294-ibc 3.5.6-1-ARCH #1 SMP PREEMPT Sun Oct 7 19:33:50 CEST 2012 i686
Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=ec6a9a60-8d8c-4de0-960b-9e2a044d0ca5 ro quiet
Build Date: 05 October 2012 02:01:30PM
Current version of pixman: 0.26.2
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Sat Oct 13 09:26:12 2012
(==) Using config directory: "/etc/X11/xorg.conf.d"
Initializing built-in extension Generic Event Extension
Initializing built-in extension SHAPE
Initializing built-in extension MIT-SHM
Initializing built-in extension XInputExtension
Initializing built-in extension XTEST
Initializing built-in extension BIG-REQUESTS
Initializing built-in extension SYNC
Initializing built-in extension XKEYBOARD
Initializing built-in extension XC-MISC
Initializing built-in extension SECURITY
Initializing built-in extension XINERAMA
Initializing built-in extension XFIXES
Initializing built-in extension RENDER
Initializing built-in extension RANDR
Initializing built-in extension COMPOSITE
Initializing built-in extension DAMAGE
Initializing built-in extension MIT-SCREEN-SAVER
Initializing built-in extension DOUBLE-BUFFER
Initializing built-in extension RECORD
Initializing built-in extension DPMS
Initializing built-in extension X-Resource
Initializing built-in extension XVideo
Initializing built-in extension XVideo-MotionCompensation
Initializing built-in extension XFree86-VidModeExtension
Initializing built-in extension XFree86-DGA
Initializing built-in extension XFree86-DRI
Initializing built-in extension DRI2
Loading extension GLX
xinit: connection to X server lost
waiting for X server to shut down XIO: fatal IO error 0 (Success) on X server ":0"
after 554 requests (554 known processed) with 0 events remaining.
xterm: fatal IO error 11 (Resource temporarily unavailable) or KillClient on X server ":0"
xterm: fatal IO error 11 (Resource temporarily unavailable) or KillClient on X server ":0"
xterm: fatal IO error 11 (Resource temporarily unavailable) or KillClient on X server ":0"
Server terminated successfully (0). Closing log file.
xinit: unexpected signal 2
And my Xorg.0.log
[ 4955.478]
X.Org X Server 1.13.0
Release Date: 2012-09-05
[ 4955.479] X Protocol Version 11, Revision 0
[ 4955.479] Build Operating System: Linux 3.6.0-1-ARCH i686
[ 4955.479] Current Operating System: Linux x_00294-ibc 3.5.6-1-ARCH #1 SMP PREEMPT Sun Oct 7 19:33:50 CEST 2012 i686
[ 4955.479] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=ec6a9a60-8d8c-4de0-960b-9e2a044d0ca5 ro quiet
[ 4955.479] Build Date: 05 October 2012 02:01:30PM
[ 4955.479]
[ 4955.479] Current version of pixman: 0.26.2
[ 4955.479] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 4955.479] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 4955.480] (==) Log file: "/var/log/Xorg.0.log", Time: Sat Oct 13 09:26:12 2012
[ 4955.480] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 4955.480] (==) No Layout section. Using the first Screen section.
[ 4955.480] (==) No screen section available. Using defaults.
[ 4955.480] (**) |-->Screen "Default Screen Section" (0)
[ 4955.480] (**) | |-->Monitor "<default monitor>"
[ 4955.481] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 4955.481] (==) Automatically adding devices
[ 4955.481] (==) Automatically enabling devices
[ 4955.481] (==) Automatically adding GPU devices
[ 4955.481] (WW) The directory "/usr/share/fonts/TTF/" does not exist.
[ 4955.481] Entry deleted from font path.
[ 4955.481] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 4955.481] Entry deleted from font path.
[ 4955.481] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[ 4955.481] Entry deleted from font path.
[ 4955.481] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 4955.481] Entry deleted from font path.
[ 4955.481] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 4955.481] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 4955.481] Entry deleted from font path.
[ 4955.481] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 4955.481] (==) FontPath set to:
/usr/share/fonts/misc/
[ 4955.481] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 4955.481] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 4955.481] (II) Loader magic: 0x825a620
[ 4955.482] (II) Module ABI versions:
[ 4955.482] X.Org ANSI C Emulation: 0.4
[ 4955.482] X.Org Video Driver: 13.0
[ 4955.482] X.Org XInput driver : 18.0
[ 4955.482] X.Org Server Extension : 7.0
[ 4955.484] (II) config/udev: Adding drm device (/dev/dri/card0)
[ 4955.486] (--) PCI:*(0:0:2:0) 8086:3577:1014:0505 rev 4, Mem @ 0x98000000/134217728, 0x90100000/524288
[ 4955.486] (--) PCI: (0:0:2:1) 8086:3577:1014:0505 rev 0, Mem @ 0x88000000/134217728, 0x80200000/524288
[ 4955.486] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 4955.486] Initializing built-in extension Generic Event Extension
[ 4955.486] Initializing built-in extension SHAPE
[ 4955.486] Initializing built-in extension MIT-SHM
[ 4955.486] Initializing built-in extension XInputExtension
[ 4955.486] Initializing built-in extension XTEST
[ 4955.486] Initializing built-in extension BIG-REQUESTS
[ 4955.486] Initializing built-in extension SYNC
[ 4955.487] Initializing built-in extension XKEYBOARD
[ 4955.487] Initializing built-in extension XC-MISC
[ 4955.487] Initializing built-in extension SECURITY
[ 4955.487] Initializing built-in extension XINERAMA
[ 4955.487] Initializing built-in extension XFIXES
[ 4955.487] Initializing built-in extension RENDER
[ 4955.487] Initializing built-in extension RANDR
[ 4955.487] Initializing built-in extension COMPOSITE
[ 4955.487] Initializing built-in extension DAMAGE
[ 4955.487] Initializing built-in extension MIT-SCREEN-SAVER
[ 4955.487] Initializing built-in extension DOUBLE-BUFFER
[ 4955.487] Initializing built-in extension RECORD
[ 4955.487] Initializing built-in extension DPMS
[ 4955.487] Initializing built-in extension X-Resource
[ 4955.487] Initializing built-in extension XVideo
[ 4955.487] Initializing built-in extension XVideo-MotionCompensation
[ 4955.487] Initializing built-in extension XFree86-VidModeExtension
[ 4955.487] Initializing built-in extension XFree86-DGA
[ 4955.487] Initializing built-in extension XFree86-DRI
[ 4955.487] Initializing built-in extension DRI2
[ 4955.487] (II) LoadModule: "glx"
[ 4955.488] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 4955.489] (II) Module glx: vendor="X.Org Foundation"
[ 4955.489] compiled for 1.13.0, module version = 1.0.0
[ 4955.489] ABI class: X.Org Server Extension, version 7.0
[ 4955.489] (==) AIGLX enabled
[ 4955.489] Loading extension GLX
[ 4955.489] (==) Matched intel as autoconfigured driver 0
[ 4955.489] (==) Matched intel as autoconfigured driver 1
[ 4955.489] (==) Matched vesa as autoconfigured driver 2
[ 4955.489] (==) Matched modesetting as autoconfigured driver 3
[ 4955.489] (==) Matched fbdev as autoconfigured driver 4
[ 4955.489] (==) Assigned the driver to the xf86ConfigLayout
[ 4955.489] (II) LoadModule: "intel"
[ 4955.490] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[ 4955.491] (II) Module intel: vendor="X.Org Foundation"
[ 4955.491] compiled for 1.13.0, module version = 2.20.9
[ 4955.491] Module class: X.Org Video Driver
[ 4955.491] ABI class: X.Org Video Driver, version 13.0
[ 4955.491] (II) LoadModule: "vesa"
[ 4955.491] (WW) Warning, couldn't open module vesa
[ 4955.491] (II) UnloadModule: "vesa"
[ 4955.492] (II) Unloading vesa
[ 4955.492] (EE) Failed to load module "vesa" (module does not exist, 0)
[ 4955.492] (II) LoadModule: "modesetting"
[ 4955.492] (WW) Warning, couldn't open module modesetting
[ 4955.492] (II) UnloadModule: "modesetting"
[ 4955.492] (II) Unloading modesetting
[ 4955.492] (EE) Failed to load module "modesetting" (module does not exist, 0)
[ 4955.493] (II) LoadModule: "fbdev"
[ 4955.493] (WW) Warning, couldn't open module fbdev
[ 4955.493] (II) UnloadModule: "fbdev"
[ 4955.493] (II) Unloading fbdev
[ 4955.493] (EE) Failed to load module "fbdev" (module does not exist, 0)
[ 4955.493] (II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G, 915G,
E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G,
965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45,
4 Series, G45/G43, Q45/Q43, G41, B43, B43, Clarkdale, Arrandale,
Sandybridge Desktop (GT1), Sandybridge Desktop (GT2),
Sandybridge Desktop (GT2+), Sandybridge Mobile (GT1),
Sandybridge Mobile (GT2), Sandybridge Mobile (GT2+),
Sandybridge Server, Ivybridge Mobile (GT1), Ivybridge Mobile (GT2),
Ivybridge Desktop (GT1), Ivybridge Desktop (GT2), Ivybridge Server,
Ivybridge Server (GT2), Haswell Desktop (GT1), Haswell Desktop (GT2),
Haswell Desktop (GT2+), Haswell Mobile (GT1), Haswell Mobile (GT2),
Haswell Mobile (GT2+), Haswell Server (GT1), Haswell Server (GT2),
Haswell Server (GT2+), Haswell SDV Desktop (GT1),
Haswell SDV Desktop (GT2), Haswell SDV Desktop (GT2+),
Haswell SDV Mobile (GT1), Haswell SDV Mobile (GT2),
Haswell SDV Mobile (GT2+), Haswell SDV Server (GT1),
Haswell SDV Server (GT2), Haswell SDV Server (GT2+),
Haswell ULT Desktop (GT1), Haswell ULT Desktop (GT2),
Haswell ULT Desktop (GT2+), Haswell ULT Mobile (GT1),
Haswell ULT Mobile (GT2), Haswell ULT Mobile (GT2+),
Haswell ULT Server (GT1), Haswell ULT Server (GT2),
Haswell ULT Server (GT2+), Haswell CRW Desktop (GT1),
Haswell CRW Desktop (GT2), Haswell CRW Desktop (GT2+),
Haswell CRW Mobile (GT1), Haswell CRW Mobile (GT2),
Haswell CRW Mobile (GT2+), Haswell CRW Server (GT1),
Haswell CRW Server (GT2), Haswell CRW Server (GT2+),
ValleyView PO board
[ 4955.496] (--) using VT number 7
[ 4955.508] (II) intel(0): using device path '/dev/dri/card0'
[ 4955.509] (II) intel(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 4955.509] (==) intel(0): Depth 24, (--) framebuffer bpp 32
[ 4955.509] (==) intel(0): RGB weight 888
[ 4955.509] (==) intel(0): Default visual is TrueColor
[ 4955.509] (--) intel(0): Integrated Graphics Chipset: Intel(R) i830M
[ 4955.509] (**) intel(0): Relaxed fencing disabled
[ 4955.509] (**) intel(0): Wait on SwapBuffers? enabled
[ 4955.509] (**) intel(0): Triple buffering? enabled
[ 4955.509] (**) intel(0): Framebuffer tiled
[ 4955.510] (**) intel(0): Pixmaps tiled
[ 4955.510] (**) intel(0): 3D buffers tiled
[ 4955.510] (**) intel(0): SwapBuffers wait enabled
[ 4955.510] (==) intel(0): video overlay key set to 0x101fe
[ 4955.593] (II) intel(0): Output VGA1 has no monitor section
[ 4955.593] (II) intel(0): Output LVDS1 has no monitor section
[ 4955.594] (--) intel(0): found backlight control interface /sys/class/backlight/thinkpad_screen
[ 4955.676] (II) intel(0): EDID for output VGA1
[ 4955.677] (II) intel(0): Printing probed modes for output VGA1
[ 4955.677] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 4955.677] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 4955.677] (II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 4955.677] (II) intel(0): Modeline "848x480"x60.0 33.75 848 864 976 1088 480 486 494 517 +hsync +vsync (31.0 kHz e)
[ 4955.677] (II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 489 492 525 -hsync -vsync (31.5 kHz e)
[ 4955.677] (II) intel(0): EDID for output LVDS1
[ 4955.677] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
[ 4955.677] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 4955.677] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 4955.677] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
[ 4955.678] (II) intel(0): Not using default mode "640x480" (doublescan mode not supported)
[ 4955.678] (II) intel(0): Not using default mode "640x512" (doublescan mode not supported)
[ 4955.678] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
[ 4955.678] (II) intel(0): Not using default mode "896x672" (doublescan mode not supported)
[ 4955.678] (II) intel(0): Not using default mode "928x696" (doublescan mode not supported)
[ 4955.678] (II) intel(0): Not using default mode "960x720" (doublescan mode not supported)
[ 4955.678] (II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
[ 4955.678] (II) intel(0): Printing probed modes for output LVDS1
[ 4955.678] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 +hsync +vsync (48.4 kHz P)
[ 4955.678] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz d)
[ 4955.678] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz d)
[ 4955.678] (II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz d)
[ 4955.678] (II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz d)
[ 4955.678] (II) intel(0): Output VGA1 connected
[ 4955.678] (II) intel(0): Output LVDS1 connected
[ 4955.678] (II) intel(0): Using exact sizes for initial modes
[ 4955.678] (II) intel(0): Output VGA1 using initial mode 1024x768
[ 4955.678] (II) intel(0): Output LVDS1 using initial mode 1024x768
[ 4955.678] (II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[ 4955.678] (II) intel(0): Kernel page flipping support detected, enabling
[ 4955.678] (==) intel(0): DPI set to (96, 96)
[ 4955.678] (II) Loading sub module "fb"
[ 4955.678] (II) LoadModule: "fb"
[ 4955.679] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 4955.679] (II) Module fb: vendor="X.Org Foundation"
[ 4955.679] compiled for 1.13.0, module version = 1.0.0
[ 4955.679] ABI class: X.Org ANSI C Emulation, version 0.4
[ 4955.679] (II) Loading sub module "dri2"
[ 4955.679] (II) LoadModule: "dri2"
[ 4955.680] (II) Module "dri2" already built-in
[ 4955.680] (==) Depth 24 pixmap format is 32 bpp
[ 4955.680] (II) intel(0): [DRI2] Setup complete
[ 4955.680] (II) intel(0): [DRI2] DRI driver: i915
[ 4955.680] (II) intel(0): Allocated new frame buffer 1024x768 stride 4096, tiled
[ 4955.680] (II) UXA(0): Driver registered support for the following operations:
[ 4955.680] (II) solid
[ 4955.680] (II) copy
[ 4955.680] (II) composite (RENDER acceleration)
[ 4955.680] (II) put_image
[ 4955.680] (II) get_image
[ 4955.680] (==) intel(0): Backing store disabled
[ 4955.680] (==) intel(0): Silken mouse enabled
[ 4955.681] (II) intel(0): Initializing HW Cursor
[ 4955.681] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 4955.684] (==) intel(0): DPMS enabled
[ 4955.684] (==) intel(0): Intel XvMC decoder disabled
[ 4955.684] (II) intel(0): Set up overlay video
[ 4955.684] (II) intel(0): direct rendering: DRI2 Enabled
[ 4955.684] (==) intel(0): hotplug detection: "enabled"
[ 4955.983] (--) RandR disabled
[ 4956.021] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[ 4956.021] (II) AIGLX: enabled GLX_INTEL_swap_event
[ 4956.021] (II) AIGLX: enabled GLX_ARB_create_context
[ 4956.021] (II) AIGLX: enabled GLX_ARB_create_context_profile
[ 4956.021] (II) AIGLX: enabled GLX_EXT_create_context_es2_profile
[ 4956.021] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
[ 4956.021] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[ 4956.021] (II) AIGLX: Loaded and initialized i915
[ 4956.022] (II) GLX: Initialized DRI2 GL provider for screen 0
[ 4956.023] (II) intel(0): Setting screen physical size to 270 x 203
[ 4956.124] (II) config/udev: Adding input device Power Button (/dev/input/event4)
[ 4956.124] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 4956.124] (II) LoadModule: "evdev"
[ 4956.124] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 4956.125] (II) Module evdev: vendor="X.Org Foundation"
[ 4956.125] compiled for 1.13.0, module version = 2.7.3
[ 4956.125] Module class: X.Org XInput Driver
[ 4956.125] ABI class: X.Org XInput driver, version 18.0
[ 4956.125] (II) Using input driver 'evdev' for 'Power Button'
[ 4956.125] (**) Power Button: always reports core events
[ 4956.125] (**) evdev: Power Button: Device: "/dev/input/event4"
[ 4956.126] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 4956.126] (--) evdev: Power Button: Found keys
[ 4956.126] (II) evdev: Power Button: Configuring as keyboard
[ 4956.126] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input4/event4"
[ 4956.126] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[ 4956.126] (**) Option "xkb_rules" "evdev"
[ 4956.126] (**) Option "xkb_model" "evdev"
[ 4956.126] (**) Option "xkb_layout" "us"
[ 4956.197] (II) config/udev: Adding input device Video Bus (/dev/input/event2)
[ 4956.198] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[ 4956.198] (II) Using input driver 'evdev' for 'Video Bus'
[ 4956.198] (**) Video Bus: always reports core events
[ 4956.198] (**) evdev: Video Bus: Device: "/dev/input/event2"
[ 4956.198] (--) evdev: Video Bus: Vendor 0 Product 0x6
[ 4956.198] (--) evdev: Video Bus: Found keys
[ 4956.198] (II) evdev: Video Bus: Configuring as keyboard
[ 4956.198] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A03:00/LNXVIDEO:00/input/input2/event2"
[ 4956.198] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
[ 4956.198] (**) Option "xkb_rules" "evdev"
[ 4956.198] (**) Option "xkb_model" "evdev"
[ 4956.198] (**) Option "xkb_layout" "us"
[ 4956.200] (II) config/udev: Adding input device Lid Switch (/dev/input/event3)
[ 4956.200] (II) No input driver specified, ignoring this device.
[ 4956.200] (II) This device may have been added with another device file.
[ 4956.201] (II) config/udev: Adding input device Sleep Button (/dev/input/event1)
[ 4956.201] (**) Sleep Button: Applying InputClass "evdev keyboard catchall"
[ 4956.201] (II) Using input driver 'evdev' for 'Sleep Button'
[ 4956.202] (**) Sleep Button: always reports core events
[ 4956.202] (**) evdev: Sleep Button: Device: "/dev/input/event1"
[ 4956.202] (--) evdev: Sleep Button: Vendor 0 Product 0x3
[ 4956.202] (--) evdev: Sleep Button: Found keys
[ 4956.202] (II) evdev: Sleep Button: Configuring as keyboard
[ 4956.202] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1/event1"
[ 4956.202] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 8)
[ 4956.202] (**) Option "xkb_rules" "evdev"
[ 4956.202] (**) Option "xkb_model" "evdev"
[ 4956.202] (**) Option "xkb_layout" "us"
[ 4956.204] (II) config/udev: Adding drm device (/dev/dri/card0)
[ 4956.205] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[ 4956.205] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[ 4956.205] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
[ 4956.205] (**) AT Translated Set 2 keyboard: always reports core events
[ 4956.205] (**) evdev: AT Translated Set 2 keyboard: Device: "/dev/input/event0"
[ 4956.205] (--) evdev: AT Translated Set 2 keyboard: Vendor 0x1 Product 0x1
[ 4956.205] (--) evdev: AT Translated Set 2 keyboard: Found keys
[ 4956.205] (II) evdev: AT Translated Set 2 keyboard: Configuring as keyboard
[ 4956.205] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[ 4956.205] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 9)
[ 4956.205] (**) Option "xkb_rules" "evdev"
[ 4956.206] (**) Option "xkb_model" "evdev"
[ 4956.206] (**) Option "xkb_layout" "us"
[ 4956.208] (II) config/udev: Adding input device TPPS/2 IBM TrackPoint (/dev/input/event6)
[ 4956.208] (**) TPPS/2 IBM TrackPoint: Applying InputClass "evdev pointer catchall"
[ 4956.208] (II) Using input driver 'evdev' for 'TPPS/2 IBM TrackPoint'
[ 4956.208] (**) TPPS/2 IBM TrackPoint: always reports core events
[ 4956.208] (**) evdev: TPPS/2 IBM TrackPoint: Device: "/dev/input/event6"
[ 4956.208] (--) evdev: TPPS/2 IBM TrackPoint: Vendor 0x2 Product 0xa
[ 4956.208] (--) evdev: TPPS/2 IBM TrackPoint: Found 3 mouse buttons
[ 4956.208] (--) evdev: TPPS/2 IBM TrackPoint: Found relative axes
[ 4956.208] (--) evdev: TPPS/2 IBM TrackPoint: Found x and y relative axes
[ 4956.208] (II) evdev: TPPS/2 IBM TrackPoint: Configuring as mouse
[ 4956.208] (**) evdev: TPPS/2 IBM TrackPoint: YAxisMapping: buttons 4 and 5
[ 4956.208] (**) evdev: TPPS/2 IBM TrackPoint: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 4956.208] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio1/input/input6/event6"
[ 4956.208] (II) XINPUT: Adding extended input device "TPPS/2 IBM TrackPoint" (type: MOUSE, id 10)
[ 4956.209] (II) evdev: TPPS/2 IBM TrackPoint: initialized for relative axes.
[ 4956.209] (**) TPPS/2 IBM TrackPoint: (accel) keeping acceleration scheme 1
[ 4956.209] (**) TPPS/2 IBM TrackPoint: (accel) acceleration profile 0
[ 4956.209] (**) TPPS/2 IBM TrackPoint: (accel) acceleration factor: 2.000
[ 4956.209] (**) TPPS/2 IBM TrackPoint: (accel) acceleration threshold: 4
[ 4956.210] (II) config/udev: Adding input device TPPS/2 IBM TrackPoint (/dev/input/mouse0)
[ 4956.210] (II) No input driver specified, ignoring this device.
[ 4956.210] (II) This device may have been added with another device file.
[ 4956.211] (II) config/udev: Adding input device PC Speaker (/dev/input/event5)
[ 4956.211] (II) No input driver specified, ignoring this device.
[ 4956.211] (II) This device may have been added with another device file.
[ 4956.213] (II) config/udev: Adding input device ThinkPad Extra Buttons (/dev/input/event7)
[ 4956.213] (**) ThinkPad Extra Buttons: Applying InputClass "evdev keyboard catchall"
[ 4956.213] (II) Using input driver 'evdev' for 'ThinkPad Extra Buttons'
[ 4956.213] (**) ThinkPad Extra Buttons: always reports core events
[ 4956.213] (**) evdev: ThinkPad Extra Buttons: Device: "/dev/input/event7"
[ 4956.214] (--) evdev: ThinkPad Extra Buttons: Vendor 0x1014 Product 0x5054
[ 4956.214] (--) evdev: ThinkPad Extra Buttons: Found keys
[ 4956.214] (II) evdev: ThinkPad Extra Buttons: Configuring as keyboard
[ 4956.214] (**) Option "config_info" "udev:/sys/devices/platform/thinkpad_acpi/input/input7/event7"
[ 4956.214] (II) XINPUT: Adding extended input device "ThinkPad Extra Buttons" (type: KEYBOARD, id 11)
[ 4956.214] (**) Option "xkb_rules" "evdev"
[ 4956.214] (**) Option "xkb_model" "evdev"
[ 4956.214] (**) Option "xkb_layout" "us"
[ 4960.630] (II) AIGLX: Suspending AIGLX clients for VT switch
[ 4964.186] (II) evdev: ThinkPad Extra Buttons: Close
[ 4964.189] (II) UnloadModule: "evdev"
[ 4964.189] (II) evdev: TPPS/2 IBM TrackPoint: Close
[ 4964.189] (II) UnloadModule: "evdev"
[ 4964.189] (II) evdev: AT Translated Set 2 keyboard: Close
[ 4964.189] (II) UnloadModule: "evdev"
[ 4964.189] (II) evdev: Sleep Button: Close
[ 4964.189] (II) UnloadModule: "evdev"
[ 4964.189] (II) evdev: Video Bus: Close
[ 4964.190] (II) UnloadModule: "evdev"
[ 4964.190] (II) evdev: Power Button: Close
[ 4964.190] (II) UnloadModule: "evdev"
[ 4964.192] Server terminated successfully (0). Closing log file.karol wrote:
Leonid.I wrote:@0x001A4:
To run twm, you need to install xorg-twm from [extra] (I am not sure if it installs by default). Do you have xterm installed?
According to his first post he has both xorg-twm and xterm installed.
I do indeed.
I went ahead and installed LXDE anyways, just to see what would happen. Exact same thing, it looks like everything is about to load but only the mouse cursor shows up. My Xorg.0.log is the same, so I won't post it again.
I do get an error in the console about the openbox menu.xml file missing but I doubt that's related.
X.Org X Server 1.13.0
Release Date: 2012-09-05
X Protocol Version 11, Revision 0
Build Operating System: Linux 3.6.0-1-ARCH i686
Current Operating System: Linux x_00294-ibc 3.5.6-1-ARCH #1 SMP PREEMPT Sun Oct 7 19:33:50 CEST 2012 i686
Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=ec6a9a60-8d8c-4de0-960b-9e2a044d0ca5 ro quiet
Build Date: 05 October 2012 02:01:30PM
Current version of pixman: 0.26.2
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Mon Oct 15 18:12:28 2012
(==) Using config directory: "/etc/X11/xorg.conf.d"
Initializing built-in extension Generic Event Extension
Initializing built-in extension SHAPE
Initializing built-in extension MIT-SHM
Initializing built-in extension XInputExtension
Initializing built-in extension XTEST
Initializing built-in extension BIG-REQUESTS
Initializing built-in extension SYNC
Initializing built-in extension XKEYBOARD
Initializing built-in extension XC-MISC
Initializing built-in extension SECURITY
Initializing built-in extension XINERAMA
Initializing built-in extension XFIXES
Initializing built-in extension RENDER
Initializing built-in extension RANDR
Initializing built-in extension COMPOSITE
Initializing built-in extension DAMAGE
Initializing built-in extension MIT-SCREEN-SAVER
Initializing built-in extension DOUBLE-BUFFER
Initializing built-in extension RECORD
Initializing built-in extension DPMS
Initializing built-in extension X-Resource
Initializing built-in extension XVideo
Initializing built-in extension XVideo-MotionCompensation
Initializing built-in extension XFree86-VidModeExtension
Initializing built-in extension XFree86-DGA
Initializing built-in extension XFree86-DRI
Initializing built-in extension DRI2
Loading extension GLX
Openbox-Message: Unable to find a valid menu file "/usr/share/lxde/openbox/menu.xml"
xinit: connection to X server lost
waiting for X server to shut down pcmanfm: Fatal IO error 11 (Resource temporarily unavailable) on X server :0.
XIO: fatal IO error 11 (Resource temporarily unavailable) on X server ":0"
after 2326 requests (2323 known processed) with 0 events remaining.
Server terminated successfully (0). Closing log file.
xinit: unexpected signal 2
.xinitrc for my user
exec ck-launch-session startlxde
Very wierd. -
I just got an iphone 4 and when I go to sync it, it appears in the left hand column but when I click on it there is just a blank screen with the apply logo and a tiny lock.
OK, I think I fixed it.
After trying to restore with an old backup from the phone (it estimated it would take 4 hours) I cancelled and went through the setup menus again, but set it up as a new phone. It then appeared in iTunes and I restored it from the computer, not the phone. It appears to be working, it's syncing my old apps right now.
Summary:
1. Reset settings on phone (hopefully you backed up fairly recently)
2. Set up as NEW iPhone in setup menu on phone
3. Restore from iTunes on computer when it recognizes the phone
4. Cross fingers -
Mail stopped working. Now get blank screen with icons (delete, file, forward, etc) at top. Then goes blank. iPad 2 purchase 12/11
Try to reset your ipad and/or force quit the mail app
Reset
Hold down the sleep and home keys for about 20 seconds. When you see the silver apple, let go and let it reboot. No data will be lost.
Force close an app
Double tap the home button. When you see the app previews on the screen scroll sideways if needed to get the preview in question on the screen. Flick that preview up and off the screen to close the app. Single tap the home button or home screen preview to exit the mode. -
I just updated to the new software and now my app Store is not working It is just a white blank page
I just updated the new software and now my app store will not work I have shut it down and opened up again and nothing just a blank white page ?
I'm having a similar problem.
New iPad with iOS6 just downloaded.
I cannot purchase any new items from the new Apple Store now!
It keeps asking me to fill in CC details, asking for security number, but stays red when i fill in the 3 numerals and when I click done I get a Time Out message.
This is not good Apple!!
Looks as if I will have to use my iPad One to purchase from the Apple Store.
Maybe you are looking for
-
Export terminated with warnings.
Hi All, Using Oracle 9.2.0.4.0 I did an export from an owner connected as system and the export produces a few errors related to the SYS.LT_EXPORT_PKG package. EXP-00008: ORACLE error 4068 encountered ORA-04068: existing state of packages has been di
-
Can I use an iPad for taking hand written notes using a stylus? Not a large stylus, but a one like Sumsungs.
-
Do we have any provision to store pay slabs of an employee
Hi Gurus, Do we have any provision of storing pay slabs of an employee according to their pay scale groups and levels. For example :- 35000-900-44000-1000-54000-1200-66000 30000-800-38000-EB-900-47000-1000-57000 25000-700-32000-EB-800-40000-900-49000
-
Hi, I am extracting data from the following tables: BSEG,BKPF,COEP,MBEW and EINA. I have been told to create a VIEW etc. for this inorder to take the fields in BI. Can i use the data sources in RSA5 to take all the required data in BI? or do I have t
-
SOLVED FIXED Lenovo W500 Screen Blank / Screen Flicker on battery after 3 minutes idle
When my W500 is on battery power and idle for 3 minutes the screen will flicker once then when I press a key it will blank briefly again before I can continue using the system. this drove me crazy for over a year, but I finally found the answer: Once