New install ZH77A-G43 with cloned Server 2003 won't boot in Safe mode

Hello,
I just installed a ZH77A-G43 into an existing PC box, new Core i3, new SATA CD and 500G drive, existing tape backup connected to a SCSI card. I cloned the new harddrive into 2 partitions, the first one being a bootable Server 2003. I installed the harddrive on another computer, and the partitions appear to be cloned correctly. When I boot off the new drive in the new hardware computer it gets to the Server 2003 splash screen, and then reboots during processing of acpitabl.dat (this is in Safe mode). I've tried booting from a Server 2003 installation CD, and that also results in a reboot.
I tried removing the SCSI card, and that results in a reboot before the MSI splash screen comes up.
This is the first time I've done a hardware change like this. The MSI instructions were very simple to follow and I was exciding to see the Server 2003 splashscreen after about 30 minutes of hardware installation. But now I'm stuck and request your help.
Regards, Philip

Hello xmad,
Thanks for the suggestions. The CD that wouldn't boot is Server 2003 64 bit--no service pacts. I just tried my VISTA CD and it came up and was ready to start the installation. The hardware is
Seagate 500G harddrive connected to SATA2
LG OEM DVDRW 24X internal connected to SATA1
2 sticks of DDR3 2GB 1333MHz
Quantum DLT-V4 tape backup drive connected to SCSI card
PSU is enclosed in a case labeled ANTEC DESIGN and I can't see any infor unless I take apart the enclosure.
I just removed the SCSI card, and the system reboots immediately after 1 second or so of the MSI splashscreen. With the SCSI card in, it reboots during the Server 2003 splashscreen (during processing of acpitabl.dat).
Should this system be compatible with Server 2003 64bit?
Should I next update the BIOS as you previously suggested?
Update: I currectly have BIOS E7758IMS V1.7

Similar Messages

TS2570 Hi, MacBook Pro & Snow Leopard- startup probs. I have tried repairing with the disk utility, resetting PRAM, booting in safe mode, and finally trying to get to archive&install the o/s, but it cannot find the destination volume. IsAn erase the only

(10.6.8 Intel core duo 2009)
Hi,
I have a grey screen and grey rotating wheel startup probs. I have tried repairing with the disk utility, resetting PRAM, booting in safe mode (which gave a subset of the errors that 'disk repair' did- namely- 'invalid sibling link,invalid record count, invalid node structure, invalid key length) and finally trying to get to archive&install the o/s, but it cannot find the destination volume. Is an erase the only option? PS I have backed up most files individually, but my daughter did not back up any from her user account. Any help would be appreciated. J

Gray, Blue or White screen at boot, w/spinner/progress bar
Why is my computer slow?
..Step by Step to fix your Mac
https://discussions.apple.com/community/notebooks/macbook_pro?view=documents

OS won't boot in safe mode or with Install Disc

I'm having one of those worst nightmare ever situations: Out of no where while using my Macbook it started to freeze up and all of my icons went away on my desktop. Then, I wasn't able to restart or do any force quit of my apps. I had to hard boot and have since not been able to get past the grey screen. I then tried safe mode and it completely shut off and shuts off subsequently ever time I try to power the system up. I'm really afraid I may have lost all of my data - I haven't updated with time machine in over a month, and I have some crucial settings that would take me forever to redo - why would this happen out of the blue for no reason, I hadn't changed anything recently. Any ideas? Any help? Please and thank you in advance.....

If you are unable to boot from an OS X Installer Disc, then most likely the computer has suffered a major motherboard failure. You will need to take the computer in for repair. If you can boot from the installer disc then run the diagnostics tests:
How to run hardware diagnostics for an Intel Mac
Boot from your original OS X Installer Disc One that came with your computer. After the chime press and hold down the "D" key until the diagnostic screen appears. Run the extended tests for a minimum of two or three hours. If any error messages appear note them down as you will need to report them to the service tech when you take the computer in for repair.
Some "common" error indicators:
SNS - sensor error
MEM - memory error
HDD - hard disk drive error
MOT - fan error
Nothing ever happens "out of the clear blue for no reason." A computer is an electronic device, and electronic devices can and do fail. One good reason for backing up regularly.

Cannot boot into Safe Mode with Networking - Windows 8.1 Update

I'm trying to boot into safe mode with networking. I can successfully boot into Safe Mode, but my Network Access is always disabled.
I've tried msconfig / Click on Restart / Restart Now from the Update and Recovery menu in 'Change PC Settings'. They all eventually get me to the Same boot options menu which says ... F4 for Safe mode, F5 for Safe mode with Networking etc.. I
select the F5 Safe mode with Networking and it re-boots into Safe mode but I have no network access.
I'm connecting to my home ADSL, no proxy required. If I boot normally I have network & internet access, but in 'F5 Safe mode with Networking' my networking is disabled.
Windows 8.1 Pro x64

I can see that I am actually connected to my router, but the network icon still shows as disconnected.
What about the Network list via the Settings charm (Win-I)? Last week I was having problems with that one after long sleeps. Later I realized that although I could see the icon in the Settings charm (as normal) when I clicked on it, it still
showed the same icon as I was expecting; the difference is that it didn't show "Connected"; so, clicking on the icon proved that it was offering a Connect button and clicking that finally got me connected. Meanwhile the troubleshooters were misleading
at best and destructive at worst, suggesting I power things off, etc. I don't know if there was a fix for this specific symptom or whether I just tried a different path but yesterday instead of trying the above procedure I tried to see what the Network
troubleshooter associated with IE's "unable to connect" page would do; amazingly it identified the problem precisely. That connection had somehow acquired a connect manually attribute. The troubleshooter offered to fix that problem for me
and I accepted. Since then, no more problem.
FYI
Robert Aldwinckle

About memory issue during installing Oracle 11g on Windows Server 2003

Hi, all
When I installed Oracle 11g on Windows Server 2003 which the server is a virtual server, Oracle only can detect 2G memory.
But there are 4G memory with my server.
I want to know if the Oracle 11g's new feature or the virtual server lead the issue.
Also , I want to get your help to resolve the issue, thanks a lot.

Let me get this straight:
You have created some virtual machine using someone's unknown VM software.
You have installed Windows Server 2003 (perhaps, but not confirmed 32-bit) to that VM.
You have allocated 4GB of memory to the VM (we guess ... not sure I'm ready to take your word on this)
You are attempting to install Oracle 11g (presumably 11gR1 32 bit for Windows) in the VM
And the Oracle (installer?) seems to be reporting that you only have 2GB RAM.
Since I personally have installed Oracle 11g 32bit for Windows on Windows 2003 server with 4GB RAM and had no issues, I would be investigating the (unknown) VM environment.

Installation problem with windows server 2003 64 bit

I downloaded all hyperion components from e-deleivery for windows server 2003 64 bit when i tried to install it a message said that some component are not compatible when i removed stratigic finance and FDM components the installation started and completed .in the configuration phase many components failed to configured and here's a copy of the log file:
(Nov 21, 2010, 02:25:51 PM), com.hyperion.cis.config.wizard.adapter.WizardFormAdapterPanel, ERROR, The specified database is already configured.
(Nov 21, 2010, 02:30:34 PM), com.hyperion.cis.config.wizard.RunAllTasksWizardAction, ERROR, Error:
java.lang.NumberFormatException: null
     at java.lang.Integer.parseInt(Unknown Source)
     at java.lang.Integer.valueOf(Unknown Source)
     at com.hyperion.hit.registry.ServiceComponentImpl.getPort(ServiceComponentImpl.java:45)
     at com.hyperion.hub.HubAppServerDeployer.checkOpenLDAPFromRegistry(HubAppServerDeployer.java:282)
     at com.hyperion.hub.HubAppServerDeployer.updateOpenLDAPPort(HubAppServerDeployer.java:175)
     at com.hyperion.hub.HubAppServerDeployer.preDeploy(HubAppServerDeployer.java:113)
     at com.hyperion.cis.config.AppServerDeployer.preDeploy(AppServerDeployer.java:205)
     at com.hyperion.cis.config.wizard.RunAllTasksWizardAction.executeAppDeploymentTask(RunAllTasksWizardAction.java:604)
     at com.hyperion.cis.config.wizard.RunAllTasksWizardAction.execute(RunAllTasksWizardAction.java:215)
     at com.installshield.wizard.RunnableWizardBeanContext.run(Unknown Source)
(Nov 21, 2010, 02:41:18 PM), com.hyperion.cis.config.wizard.RunAllTasksWizardAction, ERROR, Shared Services Registration task can not be executed because Shared Services instance is not available in Registry
(Nov 21, 2010, 02:43:35 PM), com.hyperion.cis.config.wizard.RunAllTasksWizardAction, ERROR, Shared Services Registration task can not be executed because Shared Services instance is not available in Registry
(Nov 21, 2010, 02:45:21 PM), com.hyperion.cis.config.wizard.RunAllTasksWizardAction, ERROR, Shared Services Registration task can not be executed because Shared Services instance is not available in Registry
(Nov 21, 2010, 02:45:21 PM), com.hyperion.awb.config.AWBDBConfigurator, ERROR, Error:
java.lang.NullPointerException
     at com.sun.org.apache.xerces.internal.dom.ElementImpl.normalize(Unknown Source)
     at com.sun.org.apache.xerces.internal.dom.ElementImpl.normalize(Unknown Source)
     at com.sun.org.apache.xerces.internal.dom.ElementImpl.normalize(Unknown Source)
     at com.sun.org.apache.xerces.internal.dom.ElementImpl.normalize(Unknown Source)
     at com.hyperion.awb.config.PIRegistartionXMLWriter.updateHubDetails(PIRegistartionXMLWriter.java:265)
     at com.hyperion.awb.config.AWBDBConfigurator.configure(AWBDBConfigurator.java:249)
     at com.hyperion.cis.config.wizard.RunAllTasksWizardAction.executeDbConfigTask(RunAllTasksWizardAction.java:658)
     at com.hyperion.cis.config.wizard.RunAllTasksWizardAction.execute(RunAllTasksWizardAction.java:202)
     at com.installshield.wizard.RunnableWizardBeanContext.run(Unknown Source)
(Nov 21, 2010, 02:45:21 PM), com.hyperion.cis.config.wizard.RunAllTasksWizardAction, ERROR, Error:
com.hyperion.cis.config.ProcessingException
     at com.hyperion.awb.config.AWBDBConfigurator.configure(AWBDBConfigurator.java:275)
     at com.hyperion.cis.config.wizard.RunAllTasksWizardAction.executeDbConfigTask(RunAllTasksWizardAction.java:658)
     at com.hyperion.cis.config.wizard.RunAllTasksWizardAction.execute(RunAllTasksWizardAction.java:202)
     at com.installshield.wizard.RunnableWizardBeanContext.run(Unknown Source)
(Nov 21, 2010, 02:47:29 PM), com.hyperion.cis.config.CmsRegistrationUtil, ERROR, There is no logical instance of Shared Services web application in Registry
(Nov 21, 2010, 02:47:29 PM), com.hyperion.awb.config.AWBAppServerDeployer, ERROR, Error occured in deRegisterOldProductInstance(): null
(Nov 21, 2010, 02:47:29 PM), com.hyperion.cis.config.CmsRegistrationUtil, ERROR, There is no logical instance of Shared Services web application in Registry
(Nov 21, 2010, 02:47:29 PM), com.hyperion.awb.config.AWBAppServerDeployer, ERROR, ERROR:
com.hyperion.cis.config.AppDeployException: CMS Client cannot be created
     at com.hyperion.awb.config.AWBAppServerDeployer.publishBPMAInstanceDocument(AWBAppServerDeployer.java:704)
     at com.hyperion.awb.config.AWBAppServerDeployer.registerProductInstance(AWBAppServerDeployer.java:796)
     at com.hyperion.awb.config.AWBAppServerDeployer.postDeploy(AWBAppServerDeployer.java:350)
     at com.hyperion.cis.config.AppServerDeployer.postDeploy(AppServerDeployer.java:336)
     at com.hyperion.cis.config.wizard.RunAllTasksWizardAction.executeAppDeploymentTask(RunAllTasksWizardAction.java:610)
     at com.hyperion.cis.config.wizard.RunAllTasksWizardAction.execute(RunAllTasksWizardAction.java:215)
     at com.installshield.wizard.RunnableWizardBeanContext.run(Unknown Source)
(Nov 21, 2010, 02:50:11 PM), com.hyperion.cis.config.wizard.RunAllTasksWizardAction, ERROR, Shared Services Registration task can not be executed because Shared Services instance is not available in Registry
(Nov 21, 2010, 02:51:11 PM), com.hyperion.cis.config.wizard.RunAllTasksWizardAction, ERROR, Shared Services Registration task can not be executed because Shared Services instance is not available in Registry
(Nov 21, 2010, 02:54:20 PM), com.hyperion.cis.config.wizard.RunAllTasksWizardAction, ERROR, Shared Services Registration task can not be executed because Shared Services instance is not available in Registry
(Nov 21, 2010, 02:58:04 PM), com.hyperion.cis.config.wizard.RunAllTasksWizardAction, ERROR, Shared Services Registration task can not be executed because Shared Services instance is not available in Registry
(Nov 21, 2010, 02:58:16 PM), com.hyperion.essbase.config.EssbaseAgentTaskProcessor, ERROR, Error in executing the script to register Essbase as a service: exitCode = 1
(Nov 21, 2010, 02:58:54 PM), com.hyperion.cis.config.wizard.RunAllTasksWizardAction, ERROR, Shared Services Registration task can not be executed because Shared Services instance is not available in Registry
(Nov 21, 2010, 02:59:15 PM), com.hyperion.cis.config.wizard.RunAllTasksWizardAction, ERROR, Shared Services Registration task can not be executed because Shared Services instance is not available in Registry
(Nov 21, 2010, 02:59:16 PM), com.hyperion.planning.HspDBConfigurator, ERROR, Error happened: Index: 0, Size: 0
(Nov 21, 2010, 02:59:16 PM), com.hyperion.cis.config.wizard.RunAllTasksWizardAction, ERROR, Error:
com.hyperion.cis.config.ProcessingException
     at com.hyperion.planning.HspDBConfigurator.configure(HspDBConfigurator.java:209)
     at com.hyperion.cis.config.wizard.RunAllTasksWizardAction.executeDbConfigTask(RunAllTasksWizardAction.java:658)
     at com.hyperion.cis.config.wizard.RunAllTasksWizardAction.execute(RunAllTasksWizardAction.java:202)
     at com.installshield.wizard.RunnableWizardBeanContext.run(Unknown Source)
(Nov 21, 2010, 03:03:06 PM), com.hyperion.cis.config.wizard.RunAllTasksWizardAction, ERROR, Shared Services Registration task can not be executed because Shared Services instance is not available in Registry
(Nov 21, 2010, 03:05:34 PM), com.hyperion.cis.config.wizard.RunAllTasksWizardAction, ERROR, Shared Services Registration task can not be executed because Shared Services instance is not available in Registry
(Nov 21, 2010, 03:19:29 PM), com.hyperion.cis.config.wizard.RunAllTasksWizardAction, ERROR, Shared Services Registration task can not be executed because Shared Services instance is not available in Registry
(Nov 21, 2010, 03:19:30 PM), com.hyperion.hfm.config.HfmDbConfigurator, ERROR, Error while configuring HFM DatabaseEntry does not exist for these parameters in tnsnames.ora file.
(Nov 21, 2010, 03:19:30 PM), com.hyperion.cis.config.wizard.RunAllTasksWizardAction, ERROR, Error:
com.hyperion.cis.config.ProcessingException
     at com.hyperion.hfm.config.HfmDbConfigurator.configure(HfmDbConfigurator.java:151)
     at com.hyperion.cis.config.wizard.RunAllTasksWizardAction.executeDbConfigTask(RunAllTasksWizardAction.java:658)
     at com.hyperion.cis.config.wizard.RunAllTasksWizardAction.execute(RunAllTasksWizardAction.java:202)
     at com.installshield.wizard.RunnableWizardBeanContext.run(Unknown Source)
(Nov 21, 2010, 03:19:39 PM), com.hyperion.cis.config.wizard.RunAllTasksWizardAction, ERROR, Error:
java.lang.NullPointerException
     at com.hyperion.hfm.config.HfmAppServerTaskProcessor.execute(HfmAppServerTaskProcessor.java:105)
     at com.hyperion.cis.config.wizard.RunAllTasksWizardAction.executeCustomTask(RunAllTasksWizardAction.java:741)
     at com.hyperion.cis.config.wizard.RunAllTasksWizardAction.execute(RunAllTasksWizardAction.java:188)
     at com.installshield.wizard.RunnableWizardBeanContext.run(Unknown Source)
if any one installed hyperion EPMS on windows server 2003 64 bit please i need your help
thanks in advanced
Edited by: eng3m on Nov 21, 2010 3:32 PM

Hi,
EDGE/Crystal Reports Server and Enterprise are no native 64bit applications. That does mean that they only run in 32bit mode. But you can install it on a 64bit hardware with a 64bit OS.
Regards
-Seb.

Is J2EE compatible with Windows server 2003?

Is J2EE compatible with Windows server 2003? Whenever I try to install it says its not compatible, and the sun site only mention XP and 2000 Advanced Server.
Does anyone use J2EE on win2k3server? Which version do you use?

Which J2EE version are you trying to install and where did you download it from? J2EE 1.4 SDK should install and run on Windows 2003. At what point in installation exactly are you getting this message?

Can't get past OCX error when installing ODAC 11g on Windows Server 2003

I have been trying to install ODAC 11g on Windows Server 2003 and can't get past the OCX error when registering oravsdbgeng11w.dll. I've read every message on this forum even remotely related to this problem and tried every solution offered. I have done a clean install into a new Oracle home, and made sure Instant Client is always included. All service packs and automatic updates have been installed. For what it's worth I have successfully installed ODAC 11g on Windows XP Pro.
If anyone out there has been able to get this up and running and would care to share the wisdom that would be greatly appreciated.
Thanks!
Michael Young
Latitude Geographics
Victoria, BC

Michael, as you already noticed, every time I have seen this issue it has been because ODT was being installed into an Oracle home where no client exists, or perhaps installed into an old oracle home where the client was an old version (eg Oracle10), or the client was broken. Usually though, the user unchecked the instant client checkbox during the ODAC install.
So you say you checked instant client and you still got the error? That doesn't add up...
Are you using 32-bit windows? If you are using 64 bit windows be sure to tell us.
Why don't you try avoiding using instant client at all, in case it is somehow not getting installed properly.
You can do this as follows:
1) Under the download links on OTN, go to the database download page.
2) Download the Oracle Database client 11g for Microsoft Windows
3) Run this installer and Install ODP.NET 1.x and 2.x into a new Oracle home from this client install, but nothing else. If ODP.NET is not listed there (it has been a long time since I looked at that) than just install a minimal Oracle client install.
4) Close the installer
5) Go back and install ODAC and this time choose "Oracle Server" radio button during the install (rather than the client install)
6) Install ODT and ODP.NET at least and be sure they are being installed into the Oracle home created in the first steps above.
This will avoid use of Instant Client and will hopefully avoid the OCX error. Let me know if this solves your problem.
Christian

Can't install DPM agent for Windows Server 2003

Hi,
We have DPM 2012 backup server.i try to install DPM Agent on Windows server 2003 PC. but installation failed.below error are Occured.
Install protection agent on (serverName.domain name) failed:
Error 347: An error occurred when the agent operation attempted to create the DPM Agent Coordinator service on (serverName.domain name).
Error details: %1 is not a valid Win32 application
Recommended action: Verify that the Agent Coordinator service on(serverName.domain name) is responding, if it is present. Review the error details, take the appropriate action, and then retry the agent operation.
HOW CAN SORTED OUT FOLLOWING ISSURE
Thanks,
Gayan

Hi,
The below blog outlines the needed steps for protecting
Windows Server 2003 computers using Data Protection Manager 2012 R2.
http://blogs.technet.com/b/dpm/archive/2014/06/11/details-on-protecting-windows-server-2003-computers-using-data-protection-manager-2012-r2.aspx
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually
answer your question. This can be beneficial to other community members reading the thread. Regards, Dwayne Jackson II. [MSFT] This posting is provided "AS IS" with no warranties, and confers no rights."

How instal 11g RAC on Windown server 2003

How instal 11g RAC on Windown server 2003, any toturial

I would start simply with the installation guide:
http://download.oracle.com/docs/cd/B28359_01/install.111/b28251/toc.htm
Werner

SMB Extremely Slow over VPN With Windows Server 2003

Hello everyone,
I finally convinced another person at my law firm to switch to a MacBook Pro. In preparation, I am attempting to fix any compatibility problems that would put off this new user. Unfortunately, our IT guy recently switched us to a Sonicwall SSL-VPN 200. I can connect to our server through the VPN client with no problems and I can mount our internal file server, but the connection is incredibly slow. My initial reaction was that it must be a problem with Windows Server 2003 and SMB, but I was previously able to connect to and operate on our VPN through our old Fortinet (ipsec) device with no problems. Simply put, directory switching, file moving, etc. are all now incredibly slow over the VPN. Help!

Full support for SMB signing did not appear until Samba 3.0.2 released in 2004. Mac OS X 10.5 (Leopard) supports SMB signing. Previous versions require either disabling SMB signing server-side, using a third party SMB client, using the command-line smbclient program, or updating samba yourself.

Error While Installing IDES ECC6 with SQL Server 2005

Dear Experts,
I found an error while installing IDES ECC6 with SQL Server 2005. The error is raising at the stage of 17 of 24 processing the procedure of 195 of 197 (sap_z_set_permissions).
I have tried several times by configuring different type of activites but still i am facing the same problem at the same stage. Please help me in thig regard.
I herewith pasted hereunder log files information
Regards,
B.Sudharsan
ERROR 2008-01-17 18:38:47
FCO-00011 The step ExeProcs with step key |NW_Onehost|ind|ind|ind|ind|0|0|NW_Onehost_System|ind|ind|ind|ind|1|0|NW_CreateDBandLoad|ind|ind|ind|ind|10|0|NW_Postload|ind|ind|ind|ind|10|0|NW_Postload_MSS|ind|ind|ind|ind|2|0|MssProcs|ind|ind|ind|ind|1|0|ExeProcs was executed with status ERROR .
INFO 2008-01-17 18:40:05
An error occured and the user decide to stop.\n Current step "|NW_Onehost|ind|ind|ind|ind|0|0|NW_Onehost_System|ind|ind|ind|ind|1|0|NW_CreateDBandLoad|ind|ind|ind|ind|10|0|NW_Postload|ind|ind|ind|ind|10|0|NW_Postload_MSS|ind|ind|ind|ind|2|0|MssProcs|ind|ind|ind|ind|1|0|ExeProcs".
ERROR 2008-01-17 18:38:47
MDB-05053 Errors when executing sql command: <p nr="0"/> If this message is displayed as a warning - it can be ignored. If this is an error - call your SAP support.

Sudarshan,
Occasionally, mid-way through the upgrade, DB permissions to users might change. Check to see, if the users SAP<SID>, OPS$ users have the DBA privilege. Re-assign the role and try continuing with the upgrade.

Mac osx 10.6 with sbs server 2003

Hi everyone
i m using mac osx 10.6 on my imac . i want to connect it with sbs server 2003 , then i want to to make a map drive on it .I m trying it to cmd+k to connect with server but it not connecting , i m wondring do i need to configure any thing else to connect with windows server .
cheers

Hi John,
thanks for your advice, I have actually been using the two links you provided,
yet they both lack support for the home user, and all suggest that the users have a static ip address, but this is sadly not the case.
has anyone used . http://www.dyndns.com/about/home_solutions.html
Does anyone use this service at home for their server and which settings did they use ?
This would at least let me think Im working along the right lines.
Im getting stuck with the Primary DNS questions along the setup route from apple setup. : (
thanks again
Yaddle.

Unable to install oracle 9i (64) on server 2003 (64)

unable to install oracle 9i (64) on server 2003 (64) :
" setup is valid but to enother type machine"
(proc INTEL XEOM)

I have downloaded this version:
http://www.oracle.com/technology/software/products/oracle9i/htdocs/win64soft.html
Oracle9i Database Release 2 Enterprise/Standard/Personal/Client Edition
for Windows XP 2003/Windows Server 2003 (64-bit)
There is nothin to read about "just for itanium". Pls can u give me a link (or metalink ID) where u got your informations? Is it possible to run 9i 32bit on Win2k3 Enterprise 64bit?

Can't sync IMAP inbox with Exchange Server 2003

Since Lion doesn't work with Exchange Server 2003, I set up an IMAP account in Outlook 2011 via Davmail for myself and a colleague on our laptops. This has worked for my e-mail account (syncs on multiple computers, including one running Exchange directly, and with my iPad's mail client), but not for my colleague.
For some reason, my colleague's inbox receives pushes from the server, but won't send back changes made in Outlook. Messages that have been read remain unread; deleted e-mails go into what is purportedly the server's trash in Outlook 2011, but remain in the inbox on the server. Changes made on the IMAP on the laptop also don't sync to my colleague's iPhone.
Our configuration is the same.
Any ideas? Could it be on the server side?
Thanks!

I feel your pain. I also am a lone Mac user in an entire building full of PC robots, and the IT people haven't got a clue.
I've been trying to get Mac mail working with the Exchange server here, but it's just not happening. I've managed to get Entourage working though, which is far from ideal but significantly better than the web-based version of Outlook that I'd been having to use up till now.
For entourage, then yes - the incoming and outgoing servers are the same. You may need to ask your recalcitrant IT people which port numbers to use, but give it a whirl anyway.
Best of luck,
Boris
UK

New install ZH77A-G43 with cloned Server 2003 won't boot in Safe mode

Similar Messages

Maybe you are looking for