New ipad2 doesn't recognize my Canon EOS xti camera to download photos

When I connect my Canon EOS xti to the Ipad2 via a cable connection, nothing happens.
Occasionally, a message comes up stating the device is not supported.  Any suggestions?

The SD card is the easiest fix, but there's something in the settings to make the camera visible. I just can't recall what I've read. It has something to do with pict bridge or some other communication settings. You could try fiddling with those.
That said, honestly? My experience connecting my camera to my device is that it does a bit of battery drainage.  I always use a card reader but it is a personal preference thing.

Similar Messages

  • TS3850 I'm running a trial of Final Cut Pro X, but it doesn't recognize my Canon GL2. Any advice?

    I'm running a trial of Final Cut Pro X, but it doesn't recognize my Canon GL2. Any advice?

    I have seen similar posts but don't know whether anyone has a solution.
    Take a look here  https://discussions.apple.com/message/17565242#17565242
    If you are new to FCP X it may be that you are doing something wrong but unless you give precise details of every move we will have no idea what that may be.
    Message was edited by: Ian R. Brown

  • New imac doesn't recognize firewire 400

    Just got the new imac and transferred all data from my old (non-intel) imac using a firewire 400-to-800 adapter.
    Now, my new imac doesn't recognize my external (400 firewire) drives anymore. One of the drives has an USB which works with the new mac but transfers are very vey slow. The other drive has only firewire 400 and doesn't get recognized at all.
    Any solutions?
    Thanks.

    Adapters can be troublesome, I'd recommend replacing with a Firewire 400 to 800 cable like this one. You can normally find these at your local computer store, Radio Shack or of course Amazon.
    Roger

  • Migrated old back-up to new MacBook Pro, but now new machine doesn't recognize old back-up

    So last night I migrated my old back-up to my new MacBook Pro, but this morning my new machine doesn't recognize my old back-up. I'd rather not erase and back-up from scratch for numerous reasons (losing the old data, time, etc).
    Any suggestions? I'll bet this is a realatively common issue?
    Thanks in advance for any help!
    -Ron

    Looking back, at your original posts....it said it needed 774 GB?? is that at all reasonable for a full backup of your system??
    Maybe there's something more than meets the eye?
    Also maybe we can figure out what went wrong with the tmutil command. It is possible that you may have to use additional options.
    But first le's see who owns the old backup....
    From the terminal command line try this:
    sudo xattr -l "path to your backup"
    Where "path to your backup" is tha same path exactly as used in the tmutil command, that is:
    /Volumes/"Backups Device Name"/Backups.backupdb/"Backup Name"
    You should get something like this for output:
    com.apple.backupd.BackupMachineAddress:
    00000000  30 30 3A 31 64 .. .. .. .. .. .. .. .. .. .. ..  |00:1d:..:..:..:.|
    00000010  34 00                                            |4.|
    00000012
    com.apple.backupd.HostUUID:
    00000000  41 34 32 30 43 .. .. .. .. .. .. .. .. .. .. ..  |A420Cxxxxxxxxxxx|
    00000010  .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. ..  |xxxxxxxxxxxxxxxx|
    00000020  32 37 37 42 00                                   |277B.|
    00000025
    com.apple.backupd.ModelID: MacPro3,1
    The "BackupMachineAddress" is the MAC address of the Ethernet port your mother board.
    You can find the MAc address in About this Mac-> More Info. -> System report -> Network -> Ethernet 1
    The "HostUUID" is the identifier of your mother board.
    You can find it in About this Mac-> More Info. -> System report ->Hardware Overview  [that's the first thing that shows when you select System report]
    These are the way the connection of the backup to a machine is made.
    Now the tmutil inheritbackup comand should have set them to the correct values for your new machine.
    But let's' see if any of them match the new machine and then see of we haveany more options.
    Steve

  • IPhoto doesn't recognize my canon after update to Yosemite

    iPhoto doesn't recognize my Canon any more after my update to Yosemite

    Have you run Software Update since installing Snow Leopard?
    If so and all available updates have been installed, try re-downloading the current iTunes version and re-install it over the existing. No need to delete iTunes first.
    http://www.apple.com/itunes/download/

  • My computer using Windows 8 doesn't recognize my Canon Rebel. How do I fix this?

    My computer using Windows 8 doesn't recognize my Canon Rebel. How do I fix this?

    Hi MWCRILLY,
    To connect your camera to a Windows Vista or Windows 7 computer or Windows 8 computer, you'll need to change your camera's "Communication" mode.
    To set your camera up for this, please do the following:
    With the camera disconnected from the computer, turn the camera on.  Press the "Menu" button.  Now select the [Wrench, Hammer, 2] tab.  Scroll down to "Communication" and press the "Set" button.
    Select the [Print/PTP] and press "Set".  This process is more completely described (and illustrated too!) on page 121 of your Digital Rebel XT instruction manual.
    Now connect your camera to your computer and turn the camera on.  Your computer should now recognize and have access to your Digital Rebel XT.
    Unfortunately, Canon software cannot communicate with the Rebel XT when operating in this mode.
    You may download your pictures using Windows Photo Gallery.  If you haven't already done so, you may retrieve and install this program from Microsoft's download.live.com.
    Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

  • My ipad2 doesn't recognize airplay duplication. Why??

    my ipad2 doesn't recognize airplay duplication since I upgraded to ios 6.1.3 although my iphone4s does. Need some answers. Thanks a lot.
    D.

    There's no reason that airplay mirroring shouldn't work. I assume that the problem starts with there not being an airplay icon when you go to the left side of the multitasking bar?
    I have had this problem before with my iPad 2, not related to a software upgrade, but found that a reset (hold Home & Power button until it resets and the Apple logo appears) usually resolves the problem.
    I'm assuming that the ATV and iPad are definately connected to the same network as this is required for Airplay to work.

  • Downloading images from Canon EOS 7D camera results in corrupted images.

    Hi,
    I'm struggling to download images from my Canon EOS 7D camera. The images appear corrupted on my hard drive. This does not happen consistently. Some images get corrupted, but could appear properly when trying a second time. The errors occur in EOS Utility or in iPhoto: same (bad) result. I tried to repeat downloading on a Windows machine (separate) and in a Ubuntu environment (Virtual Machine on my mac). In both cases, I had no problem. Canon states that the problem resides in my iMac. The dealer of my camera mentioned that if they see those problems, it usually relates to bad connections or a poor USB cable. I also tried several USB ports and cables, but could not resolve the problem that way. Any suggestions?
    Thanks.

    I've had this issue a few times and found it falls in to a few buckets, just a few things to consider if the images show up fine in the camera but not when you copy them out.
    1) The format (version of RAW in my case I was using with Aperture
    2) The reader
    3) The drive
    4) The connection
    Format: when I first got the 7d I wanted to use the RAW.2 version. The .CR2 file format (Canon RAW version 2) is a digital photography RAW format created by Canon. "RAW" here means that this file stores information directly coming from the sensor, almost without processing. This file would show up corrupt every time i tried to open in in Aperture, or IPhoto on my Power-Mac
    G5. I could only open it up in the supplied Canon software After some poking around I found out that I had to upgrade to Aperture3 to get the new supported RAW formats. Since I can't buy a new mack I changed the version of RAW I used.
    Once I changed from using that RAW format it was fine. There are times Aperture will say that the file is corrupt but
    when I restart the application it is fine I think there are some memory issues when it does this and I have to reboot the application over time.
    The READER:I used to use a USB reader which was fine for the 10D but with the 7D and the 5D the files are much larger in RAW from 10 megs on the 10D to 25 megs or more on the 7D/5DMk2. After shooting 500 - 1000 shots in a night I'd have to download overnight in order to get everything. Some times the file would be corrupted coming over. If I pulled the file off later one by one or in smaller groups it would be fine. I have since upgraded to a Firwire 800 cards reader. Hours becomes 10 minutes for a 16Gig fill loaded card. not 8-10 hours.
    The Drive: I've seen every files copy except 1, if I am able to hook up another drive and it works I run DiskWarrior, TechTool or SoftRAID. Usually thy confirm a bad sector in the drive. I'll back up the drive with time machine or a disk dupe software and then format the drive it it's part of a RAID I replace the drive entirely from the chain.
    The connection: bad cables have also been a culprit but not often with firewire.

  • Canon Flash 430EX 11 to go with my Canon EOS 70D camera with an 18-135mm lens.

    I purchased a Canon Flash 430EX 11 to go with my Canon EOS 70D camera with an 18-135mm lens. The flash displays the icon confirming auto zoom only intermittenly and when it doesn't, twisting the camera zoom does not display on the flash screen.  All batteries are charged and the flash is locked on to the camera.
    Solved!
    Go to Solution.

    I'm not entirely certain I understand your question.  The 430EX II has can be put in a mode where it automatically follows the camera zoom (within limits... 24mm to 105mm) but you can ALSO put it into a mode where you manually control the flash zoom.  If it's in the manual control mode then it will not automatically zoom.
    It is important that the "wide" panel NOT be in-use (if you pull out and flip down the wide-panel then the flash will go to wide angle and will not zoom EVEN if it was in auto mode.)
    Press the Zoom button, then use the - / + buttons to change the zoom.  
    When under manual control there's a black "M" icon which will appear next the word "Zoom".  If the "M" is not present then it's in auto zoom mode.
    Lastly... when you change the zoom on the camera lens, typically nothing will happen on the flash UNTIL you wake the system by doing a half-press of the shutter button.    When the camera wakes up to meter and focus... that's when it adjusts the zoom on the flash head.
    Tim Campbell
    5D II, 5D III, 60Da

  • Photoshop Elements 9 and cannot open Raw files from my Canon EOS 1000D camera.

    I am using Photoshop Elements 9 on a Windows 7 based PC and would like to know why I cannot open Raw files produced by my Canon EOS 1000D camera.
    I have checked the version of the plug in as 6.5 for raw files which is supposed to open .cr2 files and should be compatible according to Adobe site info.
    any ideas for next move.
    Mick

    Hi,
    According to all of Adobe's charts, the Canon 1000D should be supported by the basic PSE 9 even without updates. When you said you checked the camera raw version in PSE, did you do that by going to the Help menu and selecting About plugins -> Camera raw?
    The Canon 1200D requires ACR 8.4 which is only compatible with PSE 12 - so for PSE 10 your brother would need the DNG converter.
    I can't find a sample raw file to try (I do have PSE 9). If you want to upload a sample file to dropbox and give me access, I could try it on my system.
    Have you tried opening one of your files on your brothers system?
    Nrian

  • I have an iPod touch and wife has a new ipad2. We share one computer. Now, when she downloads an app to her ipad the app also downloads on my iPod touch. How can we stop that?

    I have an iPod touch and wife has a new ipad2. We share one computer. Now, when she downloads an app to her ipad the app also downloads on my iPod touch. How can we stop that?

    you should have two separate account

  • How can i open RAW files in Photoshop CS4 from Canon EOS 6D camera?

    How can i open RAW files in Photoshop CS4 from Canon EOS 6D camera?

    You can't directly but can use DNG Converter to convert your files so ACR can read and process them.
    Camera Raw plug-in | Supported cameras
    Camera Raw-compatible Adobe applications

  • How to sent importet RAW files into the cloud? The files was importet from Canon EOS via camera adapter to the iPad. The Files was stored in the folder importet. But the files does not sync with photostream.

    How to sent importet RAW files into the cloud? The files was importet from Canon EOS via camera adapter to the iPad. The Files was stored in the folder importet. But the files does not sync with photostream.

    Welcome to the Apple community.
    Only photos taken on the iOS device and after photo stream was enabled will be added to photo stream.

  • Cannot open CS6, it craves JBX-plugin, and my Mac doesn't recognize the file so I can't download

    I wonder why CS6 is not complete when downloaded? Why should I have to download JBX? If needed it should be a part of Indesign. My Mac doesn't have a name of a file to open and download, so now I simply don't have CS6 and can't convert my book to Kindle for sales on Amazon.
    Terribly disappointed!
    /maria

    I am using OS X 10.9.2 and I'm attaching the error message I get. I am
    trying to install InDesign CS6 in order to convert my book to Kindle, but
    Amazon's plug-in only works with InDesign CS6 NOT with InDesign CC.
    I am attaching the Kindle Plugin also.
    2014-05-07 22:19 GMT+02:00 Jeff A Wright <[email protected]>:
        Cannot open CS6, it craves JBX-plugin, and my Mac doesn't recognize
    the file so I can't download  created by Jeff A Wright<https://forums.adobe.com/people/JeffAWright>in *Creative
    Cloud Download & Install* - View the full discussion<https://forums.adobe.com/message/6363126#6363126>

  • I have a Canon EOS T2i Camera and I want to import the RAW images into Aperture.  How do I import them as RAW images instead of jpeg ?

    How do I import RAW images from my Canon EOS T2i camera into Aperture and have them show up as RAW images and not jpeg images?

    See the list of supported raw formats:
    http://www.apple.com/aperture/specs/raw.html
    The footnote ** for the cameras  EOS Rebel T2i EF-S / 550D / Kiss X4**  says, that the raw format is only supported with Aperture 3. So you will have to upgrade to Aperture 3, to be able to import the raw from from your camera.
    Regards
    Léonie

Maybe you are looking for

  • Recommended hard drive enclosure for use with FCP?

    I will be doing capture and editing from my main HD, but want a firewire HD for backup. ANy recommendations on enclosures?

  • Help with slideshow thumbnail?

    I would like to use only an enlarged section of my slideshow hero image as my thumbnail. This Muse Site of the Day does it like that: http://www.rocketdc.com/index.html#ourwork Anyone have any idea how they pulled this off?

  • Redirecting from an abstract portal component

    Hi, I'm trying to redirect from an abstract portal component to a quicklink. I do it like told in this thread: Redirecting to external website from abstract portal component? private void redirectUrl(String target, IPortalComponentRequest request) {

  • How do i destroy an object explicitly ?

    I need to explicitly destroy an object ... how do i do it ? 1) set object to null 2) call finalize on the object 3) ur suggestion pls...

  • Pages Document

    When using Pages, how do you eliminate a blank page at the end of a document?