New iPhone 3GS will not connect to Mac

I am trying to set up my iPhone 3GS and the instructions are very straight forward. It says to connect it to my Mac with the USB cable and it will take it from there. The problem is that the phone keeps switching on and off. the apple logo shows up for 30 seconds and then it turns off again. what am i supposed to do?

Hi Slengel5,
Welcome to the Support Communities!
The article below may be able to help you with this issue.
Click on the link to see more details and screenshots. 
iPhone, iPad or iPod touch: Not responding or does not turn on
http://support.apple.com/kb/TS3281?viewlocale=en_US
Cheers,
Judy

Similar Messages

  • My iphone 3gs will not connect to itunes and it says that I need to do a system restore. It also says that I need to enter my password on the iphone to connect to itunes but I can not do this because the phone is in emergency phone call mode only.

    My iphone 3gs will not connect to itunes and it says that I need to do a system restore. It also says that I need to enter my password on the iphone to connect to itunes but I can not do this because the phone is in emergency phone call mode only.

    Turn your phone off and connect your cable to the computer, but not the device just yet. Start up iTunes. Now, hold down the home button on your phone and plug it in to the cable - don't let go of the button until iTunes tells you it's detected a phone in recovery mode. Now you can restore to factory settings.
    Unfortunately, the data on your phone is already gone if you're seeing the connect to iTunes logo.

  • My new iphone 5 will not connect with the idrive on my new BMW F30 3 Series - any ideas?

    My new iphone 5 will not connect with the idrive on my new BMW 3 Series (F30) via the lightening USB - does anyone have any ideas?

    What have you done thus far to troubleshoot your issue?  Have you powered down and rebooted your router yet?

  • New iPhone 5 will not connect to sync

    I have a new iPhone 5 I got a couple days ago and it will not connect to sync in my car. I have a Ford Fusion 2012, and I had a 3GS that I used with it, and it worked perfectly for the few months I've had the car. I've tried everything with my iPhone 5 but it will not connect. It doesn't even ask me to put in the PIN. Sync shows the PIN and then I click on sync on my phone and it just sits there for a minute until eventually it says to make sure sync is on, in range and ready to pair. Any suggestions?

    Read this it might help you http://www.apple.com/au/support/iphone/assistant/wifi/

  • New iphone 4s will not connect to home wifi.  Says password is incorrect, but it is not.

    Please help new iphone 4s from verizon will not connect to my home wifi.  I was able to connect to my sister's home wifi without any issues tonight, but now at my home and says password is incorrect. The password is correct.  I have an ipod touch gen 2 that connects with no problems. 

    make sure your home wireless network is not "hidden." Settings -> Wi-Fi -> select your home network, it it's hidden, select "other" and manually type in the network name, password, and select security type.

  • New iPhone 5 will not connect to WiFi

    I finally upgraded to a iPhone 5 from my old 3G and I cannot get it to connect ot my home WiFi.  It can see the WiFi and I have WEP encription on the network using a Netgear WGT624v3 wireless router and 128bit encryption and when I enter the password, the iPhone gives me an "incorrect Password" warning.  I have tried several times to enter it and even texted it to the phone and copied and pasted it to avoid any typos to no avail.  I have powered down the router, removed the encryption, tried another encryption key, rebooted the iPhone but cannot get it to connect.
    This is a router with a 802.11 g and b protocol working on channel 11 and I have not had issue with our iPad 2, my wife's iPhone 3GS, my old iPhone 3G or our Macbook Pro.  I also tried to enter the network manually and it just does not want to accept the password whether it needs one or not.  What am I not doing correctly?  I say that there were some issues when people upgraded from an earlier operating system to the current one but this is a new phone as of yesterday??

    OK, I'm in and here is the fix for any of you that have a Netgear router of the WGT624v3 variety:
    Open the router interface by opening a browser window and in the address bar enter http://192.168.1.1
    Log in to the router -- User name = admin and Password = password (unless you have set it up differently)
    On the left hand sidebar near the bottom Web Support and Knowledge Base
    Near the center of the screen click on Get More Downloads then be sure the model number carried over, you may need to readjust that back to the WGT624v3 because it does matter.
    Under Firmware/Software at the bottom of the list WGT624v3 Firmware Version 2.0.21_1.0.1 (North America)
    (this is a 3 version downgrade in the firmware but it works)
    Click the Download button in the pop-up then Continue without registration
    The zip file will download and you will need to extract the file wgt624v3_2_0_21_1_0_1_na.chk file to a  place you can find it later.
    Go back into the router interface http://192.168.1.1 and log in as before if necessary
    Under Mantenance click on Router Upgrade and then Locate and Select the Upgrade File from your Hard Drive: and then select the file in the folder you placed it. and then click on the Update button.
    The router will take a few minutes to load and cycle but the iPhone will connect with any of the security protocols you are using in you other network devices, 
    I then made sure the modem did not ask me to check for updates so I don't screw it up again-- Yes, this is a downgrade of 3-4 versions and you would think newer is better but there is something about the new OSi that is not compatable, don't know if this is an Apple problem or a Netgear problem.
    If you have a D-Link router, God help you but I'll bet there is a similar fix.  Newer is not always better,

  • New iphone 5s will not connect wireless to itunes

    I recently upgraded from 4s to 5s on 2 units.  The 4s would sync wireless to airport but both new 5s will not.  Neither my phone or my wife's phones will connect wireless but will when connected.  I have checked 'Sync with this iPhone over Wi-Fi'  under Summary when connected by cable and other system settings on the phones seem to be in order.  I have searched Apple site and believe all necessary steps have been taken.

    I thought I should say something since I had the same problem with iTunes 11.1.3 connecting my iOS devices. iPhone 4, 5, iPad 4th gen, all on latest iOS7. My setup is on macpro 3.1. I tried updating OS, from  OSX Lion, ML and Mavericks. Obviously, updating OS did not solve the issue. iTunes was the latest and greatest at 11.1.3 on all of them. I also had the annoying TRUST message pop up constantly, while it could connect to iPhoto, but no iTunes, for backup and syncing.
    Long story short, found out on various forums people were having success syncing their iOS devices again on previous versions of iTunes. In my case, 11.1. Going back to 10.7, it will not support iOS 7. For this, you need to delete iTunes 11.1.3.
    I found this helpful, but beware it involves Terminal.
    http://osxdaily.com/2012/02/06/delete-itunes-mac-os-x/
    Then, through good ol' google, I could fine a previous version of iTunes 11.1.
    Installed it, connected my iPhone 5, and voilà, iPhone detected as before, and ready to backup and sync.
    Spent many days researching this, it may not resolve the issue for everyone, but I hope it can help some folks running into a similar issue.

  • New iPhone 4S will not connect to itunes!

    Hello I hope someone can help. I just got my new iphone 4s. Had a 3GS before which worked perfectly with itunes syncing etc. I turned on the new phone today and went through initial set up prompts until it asked me to connect to itunes. I plugged it in and nothing happened. Usually itunes would boot up and recognise the iphone but it registered nothing. The iphone made the charging noise and then nothing. I have already done a sim swap and now cannot get the phone to work and cannot call for help as my phone wont work.
    My macbook is around 5 years old and is version 10.4.11. The version of itunes I am using is 9.
    Please can someone help me out or offer some advice on what is going wrong here!
    Thanks

    The iPhone 4S requires iTunes 10.5 or later which requires Mac OSX 10.5 or later.
    Upgrade your Mac.

  • Help!  My new iphone 5 will not connect via bluetooth to my bose speaker.  It was working just fine with my old iphone 4 and now nothing.

    Hello, I just purchased the iphone 5 and wanted to use my bose speaker which connects via blue tooth.  Well, it will not work.  It was working fine with my iphone 4 and now it will not pick up a signal.  Help!!!

    Howdy Adrianatolman,
    The following article details a number of steps that can help sort out issues with Bluetooth accessories.
    iOS: Third-party Bluetooth headsets, headphones, and keyboards
    http://support.apple.com/kb/HT1664
    Cheers,
    Allen

  • New iphone 5 will not connect to cellular network

    got new iphone 5 and can't get it connected to at&t cellular network. help.

    Read this it might help you http://www.apple.com/au/support/iphone/assistant/wifi/

  • IPhone 3Gs will not sync/charge on my mac OSX 10.4.11

    My new iPhone 3Gs will not sync/charge on my mac OSX 10.4.11, but will charge on my friends OSX 10.6.7, what do I do?

    Call AppleCare and ask them if they still have an available copy or check on Amazon, eBay, etc. If your computer will support it you will be better off buying a retail copy of Snow Leopard instead.

  • Iphone 5 will not connect

    My new iphone 5 will not connect to my new iMac 27" on bluetooth. The mac sees my phone but that is it. Also my wireless keyboard and mouse are very flaky. This was happening before and after 10.8.2 suplemental update. What else is there to do? Iwold like to transfer some photos I took.
    Thanks

    Hi tdavey51, welcome to the Apple Support Community.
    Bluetooth problems can be related to the batteries you are using on your Keyboard & Mouse, The Apple Wireless Keyboard & Magic Mouse require batteries that give 1.5V constant, some cheaper batteries are not powerful enough or don't provide a constant voltage which causes the bluetooth connection to drop. I'd recommend changing the batteries to see if this clears the issue.
    Regarding your iPhone 5, try powering it off and back on again (hold the sleep/wake button until you see slide to power off).
    The easiest way to transfer photo's from your iPhone to the computer is either through iTunes into iPhoto if your iPhone is set up to sync to that machine, just connect it using the USB charge cable to the iMac - see http://support.apple.com/kb/PH12116 for more.
    Alternatively you can e-mail the photo's to yourself or share them using Photo Stream and iCloud - http://support.apple.com/kb/HT4486 and http://support.apple.com/kb/HT4486 will give you more info on this.

  • My iPhone 3Gs would not connect to Wi-Fi

    Hello,
    My iPhone 3Gs will not connect to Wi-Fi, it results in a message that states, "unable to join the network". The IP address, Subnet Mask, Router, and DNS is blank- which I am guessing the router do not give my iPhone a valid address anymore. When I first installed the router, it gave my iPhone an address and worked excellent with my other wireless items. My other wireless items still are connecting to the internet but not the iPhone.  
    I have tried:
    - restarting the router (the firmware is updated)
    - resetting my network settings on the iPhone
    - turned my "Airplane Mode" on and off
    - syncing the iPhone with my computer to factory settings (version iOS 5.0.1)
    - I have tried changing the security to wep to wpa to wpa2
    Thank You

    Help anyone

  • New AirPort Extreme will not Connect to iPhone 5

    I just upgraded my old AirPort to an AirPort Extreme.  Everything seems to be working fine, except my iPhone 5 will not connect to the new Airport.  When it is selected as the new wifi option, the connection wheel just spins and spins and it will not connect to the wifi.

    Reset the airport to factory and start over.
    The Factory Reset universal
    Unplug your TC/AE. Hold in reset. and power the TC/AE back on..  all without releasing reset and keep holding in for about 10sec. The time is not important.. it is the front LED rapid flashing that indicates you are in factory mode.
    Release reset.
    If it doesn’t flash rapidly you have released reset at some point and try again.
    Be Gentle! Feel the switch click on. It has a positive feel..  add no more pressure after that.
    TC/AE will reboot after a couple of minutes with default factory settings and will wipe out previous configurations.
    No files are deleted on the hard disk.. No reset of the TC deletes files.. to do that you use erase from the airport utility.
    In the new setup, keep all names short, no spaces and pure alphanumeric.
    eg AEgen6 for base station name.
    Since you have issues with wireless name the bands differently.. AE24ghz and AE5ghz
    Set no security to begin with.. Set 2.4ghz to channel 11, 6, 1 in that order.
    Once the iphone connects.. please set WPA2 Personal security with a pure alphanumeric password of 10-20 characters.

  • My apple extreme wireless network is working fine with the macs but ios devices (iPhone & iPad) will not connect. I can see the network though. Everything was working until the ISP went down. Any suggestions?

    My apple extreme wireless network is working fine with two Macs but ios devices (iPhone & iPad) will not connect. I can see the network and it's telling me I'm connected but Safari says I'm not connected to the internet. Everything was working until the ISP went down. Any suggestions?

    Thank you, I've tried the support tips (resetting the network, checking security settings, etc.) and rebooting the network devices several times to no avail. I've actually been working on this for several days (when I can afford to have the network down).
    What I have to determine is what has changed in the setup...from when it WAS working just fine with all devices.

Maybe you are looking for

  • Private mode and history automatic delete after Firefox closes is not working?

    It keeps remembering history, download history, search & form history when its uncheck, cookies accepted until firefox closes and I have it set on clear history when firefox closes, but its not working even if I use the private browsing mode how do I

  • I am having some problem to write র্যা (ro-a jofola akar) in indesign

    I am having some problem to write র্যা in indesign... I am not being able to write it there, where as it's possible in MS word. Can anyone suggest me what to do?

  • Setting styles dynamically

    Can I set a style dynamically? In the component below, I want to change the button style (in the onChange event handler) according to the selected state of the button, but the style is ignored and replaced with a default version of a button. If not,

  • What is the actual bandwidth usage?

    When I use Adobe Connect I am online and broadcasting for about 4 hours a day, for 10 days at a time. I only do screen sharing and voice -- no video. I have DSL Internet. The DSL upload speeds are very poor (under 1Mb). To speed things up, I thought

  • Is 8.1 optimized for gaming?

    A question came to my head I know that 8.1 is for business, but does it have optimizations for gaming?