New K7N2 Delta2 Platinum crashes with new memory

I recently bought a new K7N2 Delta2 Platinum motherboard and 2 x 512MB DDR400 OCZ memory, and now my machine continually crashes.
I've tested the memory sticks individually using memtest, and there are no problems with the memory. However, when I was in touch with OCZ support, they mentioned that there is apparently a problem with the nForce2 chipset being able to handle new 2 x 512MB memory. I had my motherboard working successfully with old DDR400 memory (BH5-based), which I sold when I bought the new memory. I was pointed to this site by OCZ support:
http://www.bleedinedge.com/forum/showpost.php?p=30004&postcount=7
Is this the case?
If so, I'm surprised to see that MSI (or any manufacturer with nForce2 chipsets) can claim up to 3GB support. Comments?
Apparently, one thing to try is 2T command rate, but I can't find where to set it in my BIOS. I heard that it's probably set to 1T by default on my board.
Can anyone suggest any other options?
I'm somewhat frustrated that I've bought a new board and pretty expensive memory, and now have an unstable system. It's also too late to return to the reseller.
Any help would be appreciated!
Thanks.
Stuart.

Quote
I've tested the memory sticks individually using memtest, and there are no problems with the memory
Did you also test them together? If not, do so. Then up voltage as suggested.
Do you have them in dual channel, i.e one green slot and one purple slot?
Quote
Apparently, one thing to try is 2T command rate, but I can't find where to set it in my BIOS. I heard that it's probably set to 1T by default on my board.
That is correct; it is set up for 1T and can not be changed.
Not true that nforce2 chipset has problems running 2x512MB but it is notoriously picky. Your board tends to under-volt the memory too so you may be OK after increasing the voltage.
You don't say what bios you are using but bosskiller's modded bios b.72c has produced good results and addresses memory issues.
Read < here >

Similar Messages

K7n2 Delta2 platinum crashes during games / video

after having problems with the 2nd Dimm slot on my Gigabyte board i gave that away and bought an MSI socketA board as per the subject line of the post, and transplanted all the hardware onto the MSi board.
rebuilt it to the folliowing spec.
AthlonXP 3200 (stock speed and voltage with coolermaster copper jet7a+ HSF)
3x 1Gb danelec DDR400 dimms (at 8 3 3 3 and 2.7Volts) P/N d1d400-064283N
2x 300Gb maxtor Diamondmax10 Sata drives in raid0 as system drive WinXP SP2
2x 300Gb maxtor Diamondmax10 Pata drives in raid0 as data drive (channel 0 and 1 masters)
BTC DVD rom CDRW (channel 0 slave)
BTC DVD+-rw dual layer (channel 1 slave)
PNY Nvidia Geforce6800GT 256Mb
Netgear 108mb wireless card
TV Card
Jeantech PSU JN120F-600AP12V2 rated 600W
3.3V - 30A, 5V - 45A, 1st 12V rail - 18A, 2nd 12V rail - 16A
booted, and built fine, puzzeled about 2.7Volts for memory, but i guess 3Gb sucks a bit of juice.
crashed during games like doom3, farcry, trackmania sunrise etc. even just playng video! pushing up the memory voltage to 2.8v from 2.6v seemed to help... it would just run a little longer before crashing. everything is stock speed and voltage except the ram. tried all kinds of combinations of dimms in slots, tried upping the CPU Vcore. all chipset and GFX drivers are the lastest versions (5.10 for the mainboard, and whatever the current one is for the GFX card).
totally stumped. what is going on? and if anyone says i should have checked the ram compatability chart, i shouldn't HAVE to check to see if my ram is compatable. it should just work. and i am definatly NOT ditching £330 worth of ram over a £50 mainboard. the dimms are all from the same batch, same manufacturer, etc etc, and no trouble all with my old gigabyte board.
also checked the hardware, pulled cards, swapped gfx boards - my GF6800GT, spare GF5900U, old GF5200, and my old faithfull PCI GF2MX400. same problem.
now heres the kicker. got home from work for another evenings troubleshooting, (windows and games would blue screen saying i should check the drivers, or the hardware, gfx card) and found that the PSU had died. really annoyed now. when i go buy a new PSU, any suggestions? or shall i take this MSI board outside and shoot it?
come back gigabyte, all is forgiven.

If those figures are right, I can't see the PSU as the reason for your problems.
About the temps, though I haven't got that experience myself, some temperature monitors read very high levels, while BIOS tells it as all is idle, and very idle. I mean, it could be the messenger.
Yep, I searched the Internet, quote 1 below. Thermaltake?! Maybe they have changed the specs? It is twice as expensive but moves half the air as to the Spire Whisperrock I've got (quote 2). I would if I were you, really go for an 80 mm HSF anyway.
1 http://www.coolermaster.com/index.php?LT=english&Language_s=2&url_place=product&p_serial=ACB-V83-U2&other_title=+ACB-V83-U2+Jet%207%2B
"Thanks to Cooler Masters creative R&D team, the blower housing resembles a jet engine, especially with the bright LED lights placed on the front and the rear of the blower. You will not regret your purchase when you join the force with us and feel the vigor!
Application: AMD XP 3200+ and higher
Dimension: 70 x 60 x 40 mm
Fan dimension: 80 x 80 x 80 mm
Fan speed: 1900 ~ 3500 rpm
Fan airflow: 12.0 ~ 22.1 CFM
Fan life expectance: 50,000 hrs
Bearing type: Dual ball bearing
Voltage rating: 5.0 ~ 13.8V
Heat sink: Copper base with aluminum stacked fin.
Socket type: Socket A, 370, 462
Noise level: 29.3 ~ 42.6 dBA
Connector: 4 pin (power input),3 pin (speed detection)
Weight: 490g
Air pressure: 3.15 ~ 10.70 mm H2O"
2 http://www.spirecoolers.com/fcc.asp?prodid=105
"Socket A / 370 Cooling kit
Dimensions Heat sink : 80×80×44 mm (l × w × h)
12VDC Fan : 80×80×25 mm
Bearing Ball bearing
Rated speed 2300 RPM +/-10%
Rated power 1.08 W
Noise level 21.1 dBA
Air flow 28.0 CFM at 2,300 RPM
Current 0.09 A
Life hours Ball: 50.000
Features Blue transparent fan, 3 grip clip, Copper base insert, Design fan guard
Connector 3 Pin, mainboard
Application Intel : Celeron ~ 1.8 GHz (FC-PGA)
Pentium III ~ 1.13 GHz (FC-PGA)
Pentium III ~ 1.4 GHz (FC-PGA2)
AMD : Athlon ~ 1.4 GHz (Thunderbird)
Athlon MP ~ 2800+ (Thoroughbred)
Athlon XP ~ 3400+ (Barton)
Athlon XP ~ 2100+ (Palomino)
Athlon XP ~ 2700+ (Thoroughbred)
Duron ~ 1.8 GHz (Morgan)
Sempron ~ 3000+ (K7)
Thermal resistance 0.548 °C/W
Thermal type White grease pre-applied
Installation View Installation Procedure

[nForce] K7N2 Delta2 Platinum will not boot up

i have a new K7N2 Delta2 Platinum, a new computer case, and just looking to transfer my old hard drive that was on my old mobo to this new mobo and computer case. I am running XP pro w/sp2. i have installed a new dvd burner and a new cd burner. these items where not previously connected to old pc. I have a MSI-FX5500 video card installed as well. now keep in mind that i already have my old hard drive with XP pro on it, when i go connect all the devices and power on the pc, i am able to go into the bios, it recognizes my 2gigs of corsair memory, my hard drive is recognized, both my cdr/w and my dvdr/w drives are recognized, however, when it starts to load XP from my hard drive, a very quick blue screen comes and goes and i am unable to read the error message. I was wondering is there anyway to slow down or freeze the screen so that I can read the error message? Also, more information about the setup, since i am unable to load XP pro that i already have on my hard drive, I am unable to install the software drivers for either the motherboard or the video card....... Any point of direction would be greatly appreciated. I have built several computers from the ground up before and this is the first time I have ran into this problem........ thanks
MSI K7N2 Delta2 Platinum
Athlon XP 3200+ (400 MHZ FSB)
2x512 PC3200 corsair memory, 1gig pc3200 corsair memory = 2gigs of memory
Western Digital 8MB Cache 120 GB
ePOWER EP-520XP-C1B 520Watts Power Supply
+3.3V@26A,+5V@52A,+12V@28A,-12V@1A,[email protected],[email protected]
MSI Geforce FX5500 FX5500-TD256 Video Card
Asus dvd burner
Asus cdr/w drive
Windows XP Pro SP2

since the hard drive was set up on your old mobo then it'll not work straight off on the new one as the details in the registry will be different. One way around it is to boot up off the xp cd and select to install xp and then when it finds your old install on the drive select repair the old installation and this should sort it and will keep all your data thats saved on there.
Once into windows remember to uninstall ALL the old drivers and install all the new ones or problems will arrise and force you into doing a full fresh install.

K7N2 DELTA2 PLATINUM - Sound Probs, Very Strange

OK, i bought a brand new K7N2 DELTA2 PLATINUM and it works great, except from the sound which installs and in the system devices it is registered as there without yellow explanation or red cross. Is set to auto not disable in cmos.
When I try playing something it plays but no sound actually comes out. I have checked the front port switch and accourding to the manual (which was wrong over clearing the cmos, thanks guys for helping me solve that) is fine. Cab even adjust volumes in the volume control in windows.
I have tried various different drivers including the included ones and various of the internet. I have the mid Jan versions of all nforce drivers.
Everthing else on comp works fine, though if i leave the computer unplugged at mains for more than a few secs, when i switch back on the keyboard or mouse (ps/2) do not respond and all the light of the keyboard are on whether the computer is on or not. This is solved by unplugging and plugging back in mouse and keyboard.
I have also borrowed a pci card from someone and it works fine.
Please help, suggestions would be much appreciated
Note, other thing is that it is a Realtek ALC650 chip officially though something came up on a program listing system stuff that it s an ALC655; just thought i would include.

Quote from: Dr Stu on 01-February-06, 05:09:51
good idea to try knoppix
if knoppix does work, then back in windows, did you install this audio driver?
http://www.nvidia.com/object/nforce_audio_4.62_win2kxp.html
just out of interest what was your old motherboard?
It was a shite PC Chips M848A, with some c-media 5.1 audio chip.
Thanks for helping mate.

MSI K7N2 Delta2 Platinum (No monitor output)

Hi,
I recently purchased the MSI K7N2 Delta2 Platinum along with a AMD XP 3200, 512mb DDR Memory, ATI Radeon 9250 256mb and a Maxtor 80Gb Hard disk.
I followed the included instruction manual closely and feel that everything was installed correctly. However, when I went to boot the computer, there was no output on my monitor.
The LED on the monitor was green for a few seconds, it then went orange. The screen itself was black, there was no BIOS screen.
I have tried 2 monitors, which eliminates them as the problem, I have also tried 2 graphics cards, which also eliminates them.
The other components seem to be running fine.
Any help is appreciated.
Thanks

Quote
PSU is fine. As it powers up the computer fine.
not really, as the computer doesn't POST. Is your problem caused by your PSU?
Quote
I don't understand what you mean by d bracket or whatever?
D-Leds explained
D-Bracket Info

@Klondike K7N2 Delta2 Platinum, new owner.

Hi.
I am kinda old but maybe not as old as you . Experience before...
Much regard to your efforts for writing some exhaustive information on the MSI K7N2 Delta2 Platinum. I think I would be more than completely lost without your help http://www.nforcershq.com/forum/here-vp624299.html#624299. Now at least my system is running.
I have some specific points, and please forgive me if I'm asking something you may have answered. Got kids running around, that kind of thing. Have to run out and pick up milk in a minute, life is busy, you get it... sure? Any links are helpful too.
The existing server had an XP software raid (hack some dm* files a bit, there is a toms hardware article on it here http://www.tomshardware.com/reviews/windowsxp-make-raid-5-happen,925-2.html on a Shuttle AN35 Ultra 400 and a Barton Athlon XP 2600+ 0343.
But it's a barebones board so I thought I would 'Upgrade' the file server with an 'everything' board. Enter the K7N2 Delta2 Platinum. Enter also a 0310 2500+ which I patched the mobile jumper for fun and cut all of L6. The NFORCE2 seems to ignore these settings, and swapping in the 2600+ completely stock doesn't seem to change anything below:
Questions I have which I have not got answered yet (and running 1/20/2005 bios the board came with): I can't adjust the vCore! I can only set it in the bios but not in Windows, where I have 8rdavcore - this dynamically lowered my FSB and vcore when the system was idle. 8rdavcore lists the board but there is no driver in the drop-down: this is not the giveio.sys driver mentioned on the home page, it is a driver to interface with the vcore and other settings on the board.
With your recommendations klondike the system at least boots reliably. Already I am disappointed in the MSI versus the Shuttle for this reason alone, no vcore and the settings seem really picky in the MSI Bios. The shuttle though had a periodic problem with crashes which I never figured out. LC 6420GP 80plus PS, ATI 9250 AGP, Team Value memory (identical in timing to the Value memory in your post Klondike), 3ware 9500S-8 hardware raid, NEC USB 5 port USB card and a 3com 10/100, all moved to the new system, with the 3ware newly introduced replacing the software raid. Removes the annoying rebuild when the system crashes out, prevents major disk data glitches.
I want this system to dynamically underclock, but as yet, I cannot adjust the vcore down. For example, Corecenter, or nTune, has the field for vcore and other values, but except for FSB, they are locked, and 8rdavcore log shows it cannot load the driver. The Shuttle went to under 100 fsb with a low voltage dynamically, I think vcore 1.25 with the Athlon XP Barton 2600+, and run super-cool and use about 75 watts of power vs 110w.
Any ideas?

Came back to the machine, swapped back in the Athlon XP Barton 2600+, took a look in the BIOS (don't know if I changed anything, probably), and now the vCore is greyed out again in 8rdavcore. "No ATXP1 found."
Edit: I used the CMOS jumper to reset settings several times to no effect.
Sorry I did not get the log when it was working. I will next time! I assume where it says "not responding" has something to do with the problem.
Here is the log from 8rdavcore:
Code: [Select]
00/24 16:36:50 | ===============================================
00/24 16:36:50 | 8RDAVCORE: Version 8rdavcore 0.8.8-dev8
00/24 16:36:50 | 8RDAVCORE: Windows NT/2000/XP detected
00/24 16:36:50 | giveio: Opened Service-manager successfully
00/24 16:36:50 | giveio: Service giveio exists
00/24 16:36:50 | giveio: Service giveio is running
00/24 16:36:50 | board: Found section General
00/24 16:36:50 | board: Found section Abit KT7A
00/24 16:36:50 | board: Found section Abit NF7
00/24 16:36:50 | board: Found section Acorp NFU400N
00/24 16:36:50 | board: Found section Aopen AK79D-400VN
00/24 16:36:50 | board: Found section Asus A7N8X-E
00/24 16:36:50 | board: Found section Asus A7N8X v2.0 Deluxe
00/24 16:36:50 | board: Found section Chaintech CT-7NJL1/CT-7NJS
00/24 16:36:50 | board: Found section DFI Infinity NFII Ultra
00/24 16:36:50 | board: Found section DFI Lanparty NFII Ultra
00/24 16:36:50 | board: Found section Epox EP-8RDA+ Rev. 1.x
00/24 16:36:50 | board: Found section Epox EP-8RDA+ Rev. 2.x
00/24 16:36:50 | board: Found section Epox EP-8RDA(3,6,+,I,E)
00/24 16:36:50 | board: Found section Gigabyte GA-7N400 Pro
00/24 16:36:50 | board: Found section Gigabyte GA-7NNXP
00/24 16:36:50 | board: Found section Jetway N2PA
00/24 16:36:50 | board: Found section Leadtek K7NCR-18D
00/24 16:36:50 | board: Found section MSI K7N2 Delta L
00/24 16:36:50 | board: Found section Shuttle AN35N Ultra V1.1
00/24 16:36:50 | board: Found section Shuttle SN45G
00/24 16:36:50 | board: Found section Soltek 75FRN(2)-L
00/24 16:36:50 | board: Found section Soltek NV400-L64
00/24 16:36:50 | SMI: Got IO base 0x4400
00/24 16:36:50 | SMI: Back-to-back writes disabled.
00/24 16:36:50 | smi: Function code not set, forcing to 0x88
00/24 16:36:50 | SMI: Not responding.
00/24 16:36:50 | 8RDAVCORE: Using board MSI K7N2 Delta L
00/24 16:36:50 | nforce2_smbus: 1.1: 0x8410de
00/24 16:36:50 | nforce2_smbus: Address of bus 0 is 0x5000
00/24 16:36:50 | nforce2_smbus: Address of bus 1 is 0x5100
00/24 16:36:50 | 8rdavcore: Init SMBUS drivers done
00/24 16:36:50 | atxp1: Searching on NFORCE2_SMBUS:NFORCE2_SMBUS0
00/24 16:36:50 | atxp1: Searching on NFORCE2_SMBUS:NFORCE2_SMBUS1
00/24 16:36:51 | atxp1: No ATXP1 found
00/24 16:36:51 | SMI: Not responding.
00/24 16:36:51 | SMI: Not responding.
00/24 16:36:51 | SMI: Not responding.
00/24 16:36:51 | SMI: Not responding.
00/24 16:36:51 | SMI: Not responding.
00/24 16:36:51 | 8rdavcore: Init voltage drivers done
00/24 16:36:51 | nforce2-pci: Revision c1
00/24 16:36:51 | 8rdavcore: Init chipset drivers done
00/24 16:36:51 | WINBOND: Found a W83627THF
00/24 16:36:51 | ite: ITE8712F found
00/24 16:36:51 | ITE: 16-bit fan counter 0x3c
00/24 16:36:51 | SMI: Not responding.
00/24 16:36:51 | SMI: Not responding.
00/24 16:36:51 | SMI: Not responding.
00/24 16:36:51 | SMI: Not responding.
00/24 16:36:51 | SMI: Not responding.
00/24 16:36:51 | SMI: Not responding.
00/24 16:36:51 | SMI: Not responding.
00/24 16:36:51 | lm90: Searching on NFORCE2_SMBUS:NFORCE2_SMBUS0
00/24 16:36:51 | lm90: Searching on NFORCE2_SMBUS:NFORCE2_SMBUS1
00/24 16:36:51 | lm90: No LM90 found
00/24 16:36:51 | 8rdavcore: Init sensor drivers done
00/24 16:36:51 | smart: Physical drive 0 opened
00/24 16:36:51 | smart: SMART enabled on drive 0
00/24 16:36:51 | smart: Physical drive 1 opened
00/24 16:36:51 | smart: SMART_GET_VERSION failed
00/24 16:36:51 | smart: Physical drive 2 opened
00/24 16:36:51 | smart: SMART_GET_VERSION failed
00/24 16:36:51 | smart: Physical drive 3 opened
00/24 16:36:51 | smart: SMART_GET_VERSION failed
00/24 16:36:51 | smart: IDE drive 0
00/24 16:36:51 | smart: Model: ST3750640AS
00/24 16:36:51 | smart: Firmware: 3.AAE
00/24 16:36:51 | smart: Serial: 3QD14TMH
00/24 16:36:51 | smart: Buffer: 16777216 Byte
00/24 16:36:51 | smart: Available attributes (F=Pre-Failure, O=On-Line, P=Performance, E=Error-rate, C=Event-Count, S=Self-Preserving):
00/24 16:36:51 | smart: ID Name Value Worst Threshold Raw Flags
00/24 16:36:51 | smart: 1 Raw Read Error Rate 117 91 6 158 FOPE
00/24 16:36:51 | smart: 3 Spin Up Time 94 93 0 0 FO
00/24 16:36:51 | smart: 4 Start Stop Count 100 100 20 102 O CS
00/24 16:36:51 | smart: 5 Reallocated Sector Count 100 100 36 0 FO CS
00/24 16:36:51 | smart: 7 Seek Error Rate 72 60 30 153 FOPE
00/24 16:36:51 | smart: 9 Power on time 100 100 0 195 O CS
00/24 16:36:51 | smart: 10 Spin Retry Count 100 100 97 0 FO C
00/24 16:36:51 | smart: 12 Power Cycle Count 100 100 20 106 O CS
00/24 16:36:51 | smart: 187 Unknown 100 100 0 0 O CS
00/24 16:36:51 | smart: 189 Unknown 100 100 0 0 O ECS
00/24 16:36:51 | smart: 190 Unknown 63 54 45 37 O S
00/24 16:36:51 | smart: 194 Temperature 37 46 0 37 O S
00/24 16:36:51 | smart: 195 Hardware ECC Recovered 81 61 0 207 O EC
00/24 16:36:51 | smart: 197 Current Pending Sector 100 100 0 0 O C
00/24 16:36:51 | smart: 198 Offline Uncorrectable 100 100 0 0 C
00/24 16:36:51 | smart: 199 UDMA CRC Error Count 200 200 0 3 OPECS
00/24 16:36:51 | smart: 200 Write Error Count 100 253 0 0
00/24 16:36:51 | smart: 202 Unknown 100 253 0 0 O CS
00/24 16:36:51 | 8rdavcore: Init SMART drivers done
00/24 16:36:51 | pnp: Detected W83627THF
00/24 16:36:51 | pnp: Registers are unlocked
00/24 16:36:51 | pnp: GPIO config: 0x40, 0x40, 0x00, 0x00, 0x00
00/24 16:36:51 | pnp: LD7: CR30=0x0f, 0xf0, 0xff, 0x0b, 0xff, 0xff, 0x00
00/24 16:36:51 | pnp: LD8: CR30=0x01, 0xff, 0x5e, 0x00
00/24 16:36:51 | pnp: LD9: CR30=0x00, 0xff, 0xff, 0xff
00/24 16:36:51 | cpuload: thread created, id: 208, update: 5000
00/24 16:36:51 | autofsb: autofsb_load(): Added AutoFSB1
00/24 16:36:51 | autofsb: autofsb_load(): Added AutoFSB1.2
00/24 16:36:51 | 8rdavcore: Chipset reported multiplier: 115
00/24 16:36:52 | 8rdavcore: Calculated multiplier: 114
00/24 16:36:52 | 8rdavcore: init_values done
00/24 16:36:54 | 8rdavcore: Using driver
00/24 16:36:54 | control: control_set_val(): POSSIBLE BUG: Got a NULL pointer
00/24 16:36:54 | 8rdavcore: Init control startup values done
00/24 16:36:54 | 8rdavcore: Create sensor list done
00/24 16:36:54 | 8rdavcore: Create preset list done
00/24 16:36:54 | 8rdavcore: Create AutoFSB list done
00/24 16:36:54 | 8rdavcore: Create trigger list done
00/24 16:36:54 | 8rdavcore: Create sensor field done
00/24 16:36:54 | 8rdavcore: No primary VCore control!
00/24 16:36:54 | 8rdavcore: Create voltage list done
00/24 16:36:55 | 8rdavcore: Create SMART list done
00/24 16:36:55 | 8rdavcore: AutoFSB disabled
00/24 16:36:59 | control: control_get_val(): POSSIBLE BUG: Got a NULL pointer
00/24 16:36:59 | 8rdavcore: Saved Main vars
00/24 16:36:59 | 8rdavcore: Saved sensor settings
00/24 16:37:00 | 8rdavcore: Saved presets
00/24 16:37:00 | 8rdavcore: Saved autofsb settings
00/24 16:37:01 | 8rdavcore: Saved log settings
00/24 16:37:01 | 8rdavcore: Freeing lists...
00/24 16:37:01 | Done.

Problems with K7N2 Delta2 Platinum

Hello!
Just bought new mobo, MSI K7N2 Delta2 Platinum and I am trying to get it working. My problem: Computer starts OK but there's no signal from GPU and no diagnose sound (the beeb when the computer starts). No picture nor sound. What should I do? I've tried another Graphics card but it didn't help. Should I jumper the processor somehow?
Technical specs:
-AMD Athlon 3000plus
-MSI K7N2 Delta2 Platinum
-1 gig 400Mhz Samsung DDR-RAM
-Antec Sonata case and TruePower 380W Power
-Ati Radeon X800 Pro GPU
The probelm might be in the PSU's 12V line, because I had a problem plugging it to the mobo. It didn't go to the bottom, I had to put some force for the effort .
Thanks you all trying to manage this for me

Quote from: Richard on 11-August-05, 01:22:03
rickshaw,
The DLED indicated RAM that is not compatible with nForce. I would still recommend trying nForce Approved RAM to be sure.
Take Care,
Richard
ohm. I found it myself already. Are you 100% sure it was the "RAM is not compatible with nForce"-led because there seems to be DDR
400 SAMSUNG 512MB 64M X 64 3 M368L6423ETM-CCC on the list and my memory is labeled M368L6523BTM-CCC so it appears to be quite identic to the one on the list? So many Samsungs on the list, why would my memory do any difference ?

[AMD] problems errors ram with cpu vcore change on k7n2 delta2 platinum

hello
i'm a french new owner of k7n2 delta2 platinum and i got something strange.
I have 2*512 PC3200 cas3 of kingston value ram with voltage 1.75 instead of 1.6v running in dual CAS 2.5/3/3/8 at FSB 195 like the cpu : 2500xp barton.
With occt and memtest86+ i'm stable with a CPU vcore at 1.725.After 195 the computer starts but not really stable. So i put the cpu vcore at 1.75 to put higher fsb and then i get thousands RAM errors with memtest(even if i stay fsb 195). i tried with cas 3/3/3/11 and it was worst. On the bios B5 i tried with different settings : agressive, optimal, 1/1, auto, manual, patch ddr or not...and always the same. My PSU is 450w noname and i've 4 HD 1player 1 burner & a geforce 5200 o/c 10%.
Of course i'm happy to reach 195 but i feel disapointed to be stop with this problem of vcore/ram because i have not problem of temperature with a silent boost for cpu(52°c maxi), 3 fans for the box(35°c maxi) and copper memory heat spreaders for ram.
thanks for your answer

the thing to check is the vdimm voltage for the ram ... i'm pretty sure it should be around 2.6 volts .. try upping it one step
vcore is the voltage to the cpu and doesn't affect the ram

Problems errors ram with cpu vcore change on k7n2 delta2 platinum

hello
i'm a french new owner of k7n2 delta2 platinum and i got something strange.
I have 2*512 PC3200 cas3 of kingston value ram with voltage 1.75 instead of 1.6v running in dual CAS 2.5/3/3/8 at FSB 195 like the cpu : 2500xp barton.
With occt and memtest86+ i'm stable with a CPU vcore at 1.725.After 195 the computer starts but not really stable. So i put the cpu vcore at 1.75 to put higher fsb and then i get thousands RAM errors with memtest. i tried with cas 3/3/3/11 and it was worst. On the bios B6 i tried with different settings : agressive, optimal, 1/1, auto, manual, patch ddr or not...and always the same. My PSU is 450w and i've 4 HD 1player 1 burner.
Of course i'm happy to reach 195 but i feel disapointed to be stop with this problem of vcore/ram

Quote from: osnavi on 23-September-05, 11:36:11
"...So i put the cpu vcore at 1.75 to put higher fsb and then i get thousands RAM errors with memtest..." I would say it's not the v. core but the CPU o/c. that gives that errors, as it make not sence to increase v.core only for itself.
Oh yes it does
The CPU and memory work hand-in-hand. If one is out of sync it can cause the other to start spitting out errors.
You are overclocking and that more of a scientific art, not an exact science.
Components react differently to an entire list of variables, especially the CPU/memory.
What you are trying to do requires trail and error testing however I agree the Kingston memory is holding you back at this point with the clock you are pushing
I would go for the most stable FSB settings that allow Dynamic Overclock to be enabled to SERGEANT before I would go for ultra High FSB because you will peak the system at its highest performance curve when you need the boost, and I would bet money that peak would be higher than any strait FSB over-clock you can hit stable.
Psychologically allot of people think their systems are not running the highest performance it can unless they set the system up at the highest FSB/multiplier and that is simply not true with dynamic overclocking enabled and correctly tuned with the rest of the components.

Help with MSI K7n2 Delta2 Platinum

Hi everyone,
I need some help with my system, actually I'm having troubles with my machine, often it restarts or freezes so I have to restart it manually.I own a MSI K7n2 Delta2 Platinum, AMD Athlon XP 3000+, 1 GB DDR-400 CORSAIR, ATI Radeon 9800 PRO 128MB AGP. Recently I did a clean install of Windows XP but usually I work for an hour and suddenly it restarts, and after logging in, Windows reports a log event problem; I think I have this problem because of the drivers, so I would like you to help me. Where I can get the best/last drivers for the mainboard and video card? Should I flash the bios? Is common this kind of problems? Help me please.
Thanks!

sortieins, please start an new thread and make a complete listing of your compoenents including your PSU and the amps on the various voltage rails, especially the +12V rail(s).
>>Posting Guide<<

K7N2 DELTA2 PLATINUM MEMORY UPGRADE QUESTION

I have a k7n2 delta2 plat mobo with a 3200+ and 1gb (2x512) corsair 3200, i want to get 2gb to just max it out and i was wondering if the k7n2 delta2 platinum can support 2gb of ddr400.
I'm specifially looking at these 2 sets.
Kingston HyperX KHX3200AK2/2G 2GB Kit DDR400 PC3200
http://www.zipzoomfly.com/jsp/ProductDetail.jsp?ProductCode=80097-46
and
OCZ OCZ4002048ELDCPE-K 2GB Kit DDR400 PC3200 Platinum Edition
http://www.zipzoomfly.com/jsp/ProductDetail.jsp?ProductCode=85201
Will the following RAM sets work with the k7n2 delta2 plat?
thx alot!

Well, I'm getting a new laptop for college, no new desktop for me, so ill just do what i can for the one i have now, and the reason why i aint goin with the K8 mobo n just chip cause i just wanna do it all @ once with pciE, new psu and stuff, alllll neww at one time...but for this situation its just gonna be a new laptop and some new parts for my comp. lolz.

Ever since i updated software on my macbook pro, yahoo mail new version is constantly crashing with the spinning ball of death. any ideas?

ever since i updated software on my macbook pro, yahoo mail new version is constantly crashing with the spinning ball of death. any ideas?

What is the exact spec of the clips that cause the problem?
(Open one of the files with QuickTime and press Cmd+i to open the Inspector - then report back with the what it says).
Andy

[nForce] K7N2 Delta2 Platinum w/Version B.5 BIOS, trouble with post and XP install.

I have
K7N2 Delta2 Platinum
MS-6570E Version 1.0 motherboard
AMD Sempron 2600+
Elixir 500MB PC-3200 DDR (3 sticks, total 1.5GB)
eVga Nvidia MX4000 64MB AGP card
Maxtor ATA-100 PCI controller
I pulled everything else out of the box. I've tried the B.3, B.4, and B.5 BIOS and set everything to Optimized Defaults. I created a striped RAID Array of 4 WD 80GB drives on the primary and secondary onboard controller. The CD is on the Maxtor controller.
There are some problems I can't figure out.
1) The mobo identifies the CPU as Athlon XP 1100
2) The POST hangs just before seeking the IDE drives. I have to hit a key for it to continue.
3) The LED's on the D bracket have the top right light dark until the key is hit. Something to do with initializing the floppy controller.
4) The XP install fails to a blue screen just after hitting the F8 key to accept the license. The code is 0x0000007B.
Can someone tell me what these issues have to do with each other and how I can correct them?

Quote from: dmichael34 on 17-September-05, 22:42:56
The Maxtor controller was removed when you originally suggested to do so. The add on controller is an SIL 680 RAID.
I will try reseating the processor next.
I can also attempt a boot through POST without the array, as this shouldn't affect the boot process.
I did notice that the ctrl-alt-del on the LEFT side of the keyboard doesn't work.
However, the ctrl-alt-del on the RIGHT side of the keyboard does work.
Maybe I've been looking for a serious problem and overlooking the obvious.
I do not see how the CPU temp would cause a pause at boot until "any key" is hit... it sounds more to me like the system has paused to either look for a device or boot a BIOS on a device card.
If I am not mistaken, you are using a RAID card to boot windows? Is this correct?
If that is true it is possible the boot sequence is not set correctly in the BIOS such as "BOOT OTHER DEVICE" ( I cannot remember the exact term in the BIOS)
I am not sure about that but you could try changing the boot sequence so your RAID card is above "HARD DISK" on the list

Problems with K7N2 DELTA2 PLATINUM Help Me.

Hi everyone, I have this problem with my recently bought K7N2 Delta2 Platinum . I've being installed the pc this last nights, and the pc can't post, all fans start properly but the D-Bracket indicates me this description " EARLY CHIPSET INITIALIZATION", can anyone help me??
I don´t know if my MB support a Athlon XP 1500+ processor, this is the current devices and components installed in my MoBo:
AMD athlon XP 1500 +
256 mb 184 pin DDR RAM PC 2100 spectek
Sound Blaster Live! 5.1
60 GB hard drive Maxtor IDE
40 GB hard drive Seagate IDE drive

and this
Model: K7N2 (MS-6570)
Revision: 1.0
Form Factor: ATX
Chipset: NVIDIA nForce2 SPP AGP DDR
Bios: Award 3.4 04/11/2003 or later. Recommended Speeds:
AMD Athlon™ XP 3000+ (333 FSB)
AMD Athlon™ XP 2800+ (333 FSB)
AMD Athlon™ XP 2700+ (333 FSB)
AMD Athlon™ XP 2600+ (333 FSB) Model 8
AMD Athlon™ XP 2600+ (333 FSB) Model 10
AMD Athlon™ XP 2600+ (266 FSB)
AMD Athlon™ XP 2500+ (333 FSB)
AMD Athlon™ XP 2400+ (266 FSB) Model 10 w/ 256K Cache
AMD Athlon™ XP 2400+ (266 FSB)
AMD Athlon™ XP 2200+ (266 FSB) Model 10 w/ 256K Cache
AMD Athlon™ XP 2200+ (266 FSB)
AMD Athlon™ XP 2100+ (266 FSB) Model 8
AMD Athlon™ XP 2100+ (266 FSB) Model 6
AMD Athlon™ XP 2000+ (266 FSB) Model 8
AMD Athlon™ XP 2000+ (266 FSB) Model 6
AMD Athlon™ XP 2000+ (266 FSB) Model 10 w/ 256K Cache
AMD Athlon™ XP 1900+ (266 FSB) Model 8
AMD Athlon™ XP 1900+ (266 FSB) Model 6
AMD Athlon™ XP 1800+ (266 FSB) Model 8
AMD Athlon™ XP 1800+ (266 FSB) Model 6
AMD Athlon™ XP 1700+ (266 FSB) Model 8
AMD Athlon™ XP 1700+ (266 FSB) Model 6
AMD Athlon™ XP 1600+ (266 FSB)
AMD Athlon™ XP 1500+ (266 FSB)
AMD Duron™ 1300
AMD Duron™ 1200
AMD Duron™ 1100
AMD Duron™ 1000

MSI K7N2 Delta2 Platinum + Corsair mem = hell

Alright, Last christmas I got an MSI K7N2 Delta2 Platinum Mobo. I had an AMD Athlon XP 3000+
w/333mhz FSB. I was using cheapo generic ram which worked, but had horrible performance.
So I bought the TWINX1024-3200XL, Corsair 1GB(2x512) PC3200 400mhz DDR-Ram.
So........when I set that up, I got HUGE instability problems. While playing Half-Life 2, the game
would randomly go BSOD, which I didn't get with the cheapo ram. So I went into the options and
I changed the bios settings from By SPD (which set it to 200mhz fsb) to Auto (which changed it
to 166mhz after detecting my 166mhz fsb cpu), at which point the instability ended. But every
time I tried to run it at 400mhz, tons of crashing and BSODs in HL2 as well as windows. So I've
been using it at 333mhz for the past 6 or so months without any problems, aside from the fact
that I can't run my $300 ram at stock speed.
After reading some threads here and at other forums, I learned that apparently my
motherboard doesn't allow the cpu/ram to run async. Which would make some degree of
sense, since when they ran sync, both at 333mhz, I encountered no crashing. However, I just
bought an AMD Athlon XP 3200+ w/400mhz fsb and I was hoping that the problems would be
over. Alas, no. With the bios set to By SPD at 400mhz, Half-Life 2 (which is what I use to test
system stability, since Memtest 86, Prime 95, etc. All ran through all the tests and for over 24
hours without a single error, then the second I play HL2, it crashes) crashes within 1 minute. So
I angrily restart and change the bios settings, this time I set it to Auto, which is also 400mhz now due to the 400mhz fsb CPU. I was actually able to play Half-Life 2 flawlessly for about 45 minutes, I made it past the driving phase on the buggy, shot down the chopper, then I eliminated all resistance near the crane. Unfortunately, once everything was dead silent and I pressed R to reload, BSOD. >=|
Is my motherboard a piece of crap that doesn't support the ram, or is the ram bad? Has anybody else been able to run these two (MSI K7N2 Delta2 Platinum + Corsair PC3200 Performance Ram) together with perfect stability? Please help! I'm going nuts. =*|
Many Thanks!
~Takeda
--System Specs--
Windows XP Professional SP1
Antec SX1040B2 File Server Case
550watt Antec TrueControl PSU
MSI K7N2 Delta2 Platinum
AMD Athlon XP 3200+/400mhz FSB (2.2GHz)
Thermaltake Volcano 12
1GB(2x512) Corsair Twinx1024XL Dual Channel
ATI All-In-Wonder 9800 Pro
Sound Blaster Audigy 2ZS Platinum
Pioneer 10x DVD Drive
Sony DRU-700A
Western Digital 120.0GB 7200RPM HD ATA/100
Western Digital 120.0GB 7200RPM HD ATA/100
nForce Ethernet Adapter w/Cable line
Logitech MX500 Optical Mouse
Logitech Elite Keyboard
19" Envision Monitor EN985e
Logitech Z-680 5.1 Speakers

well, for the errors. In half-life 2, after however much playtime, the screen will just randomly go blue, without any official windows message or error code, forcing me to manually restart with the reset button. It's done this for the most part. Other times, when I change the settings, the game will just boot me back to the desktop, giving me a visual basic runtime error. Oddly enough, when I set the ram to 166mhz fsb, the game is totally stable. I've also just updated to the newest bios 11.50 and tried all of the previous settings as well as the "optimized defaults" and "fail-safe defaults" all still result in the crashing.
Yeah, I've tested other games. The results were mixed though. certain games like Need For Speed Hot Pursuit 2 would lockup, other games like command and conquer generals seemed to mostly be stable, with a few random crashes. The problem is that I haven't really gotten any true BSODs in games, I just get lockups. However, windows would give BSODs, but they seemed like they were driven by faulty hardware, since it would be random and would go away entirely once I underclocked the ram.
Other times in the past when I've run the ram at 200mhz fsb, windows would randomly crash when I was browsing the web. In those cases it would give me a stop message and an error number. But I haven't gotten then so far today. I can't remember what all the errors were, but there were about 2-3 random crashes related to ntfs.sys and other system files. So at first, I thought maybe it was just a windows problem, but I had just freshly formatted and reinstalled windows, so it seemed unlikely. And of course, the second I changed it back to 166mhz fsb, I was able to keep my computer on for a week, playing half-life 2, doom 3, command and conquer generals, as well as tons of other games and general web browsing without a single incident. So the problem, although highly vague, seems to be related directly to the ram, if just by the fsb change.
I dunno, these are really really odd problems, never encountered these before in like 6 years of tweaking my comps, so I'm guessing that it's either just an incompatibility with my motherboard/ram (in which case I'm screwed), my mobo is broken, or my ram is broken. I think my only real option left, now that I've bought a new $130 cpu to match the ram is to RMA the ram and hope that it somehow works. But the fact that it's been able to pass prime95 and memtest86 flawlessly makes me concerned as to whether or not corsair will be able to diagnose a problem, if there is one, with the ram if I do RMA it. sigh.
I'm not sure if my video card is underpowered, since I have a 550watt psu and the radeon 9800 isn't too much of a hog. But I think I may RMA that as well. damn, I dunno.
*update*
Correction, it seems that now I have a 200mhz fsb cpu, setting the ram to 6:5 for 166mhz causes windows to almost immediately lock up. I'm guessing that's part of the whole unable to run the cpu/ram async thing.
Also, when I tried changing the latency to 2.5 and 3.0, I got the following error:
Many thanks!
~Takeda

New K7N2 Delta2 Platinum crashes with new memory

Similar Messages

Maybe you are looking for