New Maxtor External Firewire 800 200 GB Drive Install Help

I have noticed lots of posts on this, any suggestions before I plug it in?
Do you recommend for or against the preinstalled software? I know I need to format it, is there a link or for th is someone could point me too?
I am still new to mac so this will be my first addtiion to my G5 Du
Thanks

Not familiar with Maxtor drives, but
You can use Disk Utility to set it up. Mac OS extended journalled is the usual format. DU help covers the basics.
You may want to have at least two volumes/partitions, so that you can clone your working boot drive into one of them, with CCC for instance
http://www.bombich.com/software/ccc.html
in case of problems.
It's probably still wise to disconnect the f/w drive while updating OS X.

Similar Messages

External Firewire 800 500GB WD drive does not mount

Hi-
Here is the problem.
i) Bought a lacie 500GB d2 drive using firewire 800 to connect to the iMAC but did not work. The port was seeing the drive but disconnecting it every 10 secs thinking that I was unmounting it during operations. I returned back the drive to the apple store since i saw that it had way too many problems.
ii) Replaced the Lacie d2 drive with a WD 500 GB external firewire MyBook Pro but the mac does NOT see or mount the drive at all.
iii) Bought a 23" HD cinema display and extended my dekstop over. I did not connect the additional USB/Firewire plugs to the iMAC as I am plugging in the drive to the iMAC and not the cinema display.
I have tried the following:
-Power off the mac and disconnect the power both on the WD and the MAC
-Check/Uncheck the ports through the preferences menu for firewire
-Repaired permission with the disk utility on the internal hard drive
Any ideas as to why the ports do not recognize/mount at all this drive?

I have read elsewhere that the FW 800 port on the iMac 24 can be a bit tricky. You may want to make sure you have a good connection.
I formatted mine out of the box which is just good practice and because I wanted to make a partition bootable/clone.
Powering on/off wont make a difference.
I don't know what you mean by uncheck/check ports for firewire. There are no such prefs in OSX.
Repairing permissions has nothing to do with hardware.
You only plug the FW 800 plug into the FW 800 port on the iMac. You use the other ports on the drive to plug other drives in on a daisy chain.
Go into drive utility and see if it shows up there for formatting. If not, then you have a bad cable. Try the regular FW 400 port and hook up that way. The 400 and 800 share the same bridge. If that doesn't work, and another drive does, then the FW bus on the drive is dead.

I have a Power Mac G4 (2004) and want to transfer all my files to a new MacBook Pro 15.4". Can this be done thru firewire cable or do I have to transfer to an external Firewire 800 hard drive first?

I have a Power Mac G4 (2004) and want to transfer all my files to a new MacBook Pro 15.4". Can this be done thru firewire cable or do I have to transfer to an external Firewire 800 hard drive first?

Do it with a Firewire cable (buy a 800/400 adapter if you need it) - the USB transfer takes a much longer time.
Start up your old PowerMac G4 holding down the "T" key, for target disk mode.
On your new MacBook Pro open "Migration Assistant" in your utilities folder.
Connect the 2 computers by firewire cable and follow the prompts in Migration Assistant.

Computer crash with iTunes - Using external firewire 800 drive

I am using an external firewire 800 drive (2TB Lacie) to store all my music for iTunes... At random times this crashes the computer, the music "skips" and the computer has a grey notice telling me to shutdown immediately. I am not sure why this is happening, but think this must be some sort of conflict issue... but no clue how to resolve... Any advice would be great!! Thanks!

Oh no, sounds like kernel panics. Time to head directly to The X Lab to read the FAQs and get started with maintenance and troubleshooting. Unfortunately, this problem goes way beyond iTunes, so for additional support, you should post in the appropriate OS X forum.

Will I notice a significant performance drop if I run my Imac 8,1(early 2008) direct from an external firewire 800 Harddrive

Will I notice a significant performance drop if I run my Imac 8,1(early 2008) direct from an external firewire 800 Harddrive

I notice quite a difference in two of my externals because of that (the 5400 rpm drive was a warranty replacement and I had no idea it wouldn't be 7200 rpm - but that's another subject.....).

Can't boot from clone on external firewire 800 drive

Hello,
I have a 24" mid-2007 iMac 7,1 running Snow Leopard. I recently changed my set up to put a clean install of OS X 10.9.1 on a partition of an external SSD. I also moved the 10.6.8 start up system to a partition on the SSD. My internal iMac hard drive now has no system folder, only my data files. I have additional firewire drives for Time Machine, other data and media drives. Finally, I just bought a pair of 3TB drives that I partitioned into enough partitions to be able to clone both operating systems and all my data files for a rotating pair of offsite backups. All moving/cloning of drives was done with version 3.5.4 (Mavericks-compatible) of Carbon Copy Cloner.
I can boot from my external SSD (either Mavericks or Snow Leopard) fine and all external drives mount correctly in either case. After cloning all the partitions onto the backup drives, I tried to test the clones but I am not able to start up using either the Mavericks or the Snow Leopard clones when the backup external drive is connected via firewire 800. This is true whether I select the clone volumes in the Startup Disk preferences pane or hold down the option key during start up (note that the external drive with the clone partitions does not appear in the list of disk choices with the option key method). I get the "question mark in the folder" sign that the start up system is not being found.
I have changed the order in which the external drives are connected (normally the SSD is first in the chain), including trying when only the backup drive is connected directly to the iMac. I get the same result no matter what.
Curiously, the Mavericks and Snow Leopard boot clones start up via firewire 800 when the external backup drive is connected to my wife's 2009 13" Macbook Pro, indicating that the clones and the enclosure (an OWC Mercury Elite Pro quad interface, newer version with USB3) both support booting. Furthermore, if I connect the backup drive to my iMac using USB, the boot clones both work to start up the iMac.
This all points to an issue with the firewire bus failing to recognize the boot clones somehow during my iMac's start up process. I am rather puzzled about how to fix this.
I can get by booting via USB in an emergency but because my system is old, this is of course USB2 so its slow. If I had to use the clones to recover I'd rather be able to operate and restore at FW800 speeds.
If anyone has any ideas what might be going on, I'd appreciate hearing them.
Thanks in advance.
Greg

Did you ever get this resolved, Greg?

Bus Powered External Firewire (800) Drives and iPod?

I bought a WD Passport drive, and was pretty upset when i found out that the usb ports on my powerbook cannot power the drive. crap. can the firewire 800 port on my powerbook power these drives:
http://www.kanotechnologies.com/products/SF800-40.cfm
http://www.g-technology.com/Products/G-DRIVE-mini.cfm#Buy
I really want a bus powered drive. does anyone know if these will work with my 15" powerbook? one better than the other? oh, and i'm getting it to keep my itunes library on...so will my powerbook have any problem with reading the fw800 drive and the ipod in the fw400 port at the same time?

Well the second linked drive says it is bus powered and does not require a external power brick. Usually most of external 2.5 inch notebook drives (in a 2.5 enclosure) can be bus powered. The 3.5 inch ones are generally not bus powered.

External Firewire 800 Drive Shuts Down

I am using an external Other World Computing hard drive enclosure with a Seagate 2 TB Barracuda XT drive formatted as a single volume. The drive seems to be in proper working order and I haven't lost any data. However, every once in a while the drive power light will go off and the drive will go off line. Then it attempts to mount, but isn't able to.
I have experienced this behavior with 2 Seagate drives in different enclosures, so it doesn't seem to be a problem with the drive or enclosure itself. Could this be a problem with the Firewire 800 port on my Mac Pro?
Any help would be greatly appreciated!
-Michael

Do your external enclosures use an external Power Supply? You may be drawing too much power from the FireWire cable. This problem is much more common with unpowered USB drive enclosures that have limited ability to get power from USB.

Will aperture run off an external firewire 800 drive?

Hey All,
I have an iMac that has firewire 800 as its fastest port and my aperture library is getting too big to have on my maun hard drive. If I were to get an external enclosure will I be able to move my aperture library over and still have the same fluid workflow or am I going to get lag going over firewire 800?
Thanks
Ruwan

Adding to Williams advice:
You might consider leaving your Library on your system drive and moving most (or all) of your Images' Originals from inside your Library to an external drive. Aperture calls Originals stored outside your Library "Referenced Originals" and has robust tools for managing them. Read some of the posts here (and check the User Manual -- start here) and ask any questions you have should you choose this route.
As William said, FW800 with a good drive is usually fast enough, but keeping your Library on your system and storing your Images' Originals on an external drive will be faster. OTOH, it makes administering your Library and Originals more complex, and leaves you to back-up your Originals separately from your Library.

Imac won't recognize mac external firewire 800 drive

iMac suddenly stopped recognizing my firewire 800 gdrives. worked this afternoon, and the drives worked on my macbook pro. any suggestions would be greatly appreciated.

Reset the SMC > Resetting the System Management Controller (SMC)
1. Shut down the computer.
2. Unplug the computer's power cord.
3. Wait fifteen seconds.
4. Attach the computer's power cord.
5. Wait five seconds, then press the power button to turn on the computer.
Then the PRAM > About NVRAM and PRAM
1. Shut down the computer.
2. Locate the following keys on the keyboard: Command, Option, P, and R. You will need to hold these keys down simultaneously in step 4.
3. Turn on the computer.
4. Press and hold the Command-Option-P-R keys. You must press this key combination before the gray screen appears.
5. Hold the keys down until the computer restarts and you hear the startup sound for the second time.
6. Release the keys.
Reconnect your FireWire Drive.

External firewire 800 disk: Raid or non Raid?

Hi all,
I am currently about to by a new external firwire 800 hard disk to replace my firewire 400 200GB Maxtor. I mainly use this disk for timemachine backups and all my final cut express scratch area and work area. I am working with AVCHD video and looking to expand the storage and speed of this disk. I have narrowed my options down to two. They are both high quality options. I will be buying the enclosure and hard disks seperatly to ensure I get a good enclosure and good quality hard disk drive.
Enclosure options:
1. http://www.macpower.com.tw/products/hdd3/pleiades/pd_scombo.
Pleiades Super S-Combo, FireWire 400/800, USB 2.0, and eSATA interfaces. This enclosure uses Oxford 934DSb or Oxford 924DSb chipset. This is a single drive enclosure and non Raid. I would put a 1TB disk in this enclosure.
2. http://www.macpower.com.tw/products/hddmulti/taurus/pdd_raid2
Taurus Raid II enclosure. FireWire 400/800, USB 2.0 and USB 1.0 interfaces. This enclosure uses Oxford 934DSb or Oxford 924DSb chipset. This is a dual drive enclosure and Raid 0 and 1. I would put a two 500GB disks in this enclosure. But will use with mirroring such that a copy of data will reside on each disk. Whilst this will reduce the overal capacity to 500GB I will have the extra redundancy should a drive fail. From which I can just replace the failed drive.
I am aware that using Raid mirroring will slow down the data transfer to the disk enclosure but I think this should be ok for AVCHD editing for my purposes. Cost wise there is not much difference between the two options. In both options I will go for either Seagate Baracuda drive or Samsung Spinpoint.
Would like to know what your thoughts are?
Which options would you go for?
Message was edited by: Just-Karma

Hi all,
Ok so I decided to not go done the raid mirriring route. Instead I finally made a decision and boughts a Macpower FW800 enclousre which uses the Oxford 934 chipset and a Samsung HD103UJ 1TB Serial ATA 3.0 Gbps
buffer memory32 MB hard disk.
The enclosure is excellent quality and the disk access is very quick via FW800. The disk itself is very quiet and also great for Final Cut with my HD editing. Only noise the disk makes is upon power up other than that it is very quiet.
I have partitioned th disk into two 500GB's. One partition is used for time machine backups and the other is the Final Cut scratch space.
I plan to buy another enclosure and 1TB disk and parition into two 500GB's also. I plan to use one of the 500GB's for Super Duper clone of iMac system hard disk and the second for cloning/backing up the scratch Final Cut space. This second disk and enclosure will be my offline backup system and will not be powered all the time.
Details of the elcousre and hard disk are provided below. I purchased them in the UK. Enclosure was purchased from www.span.com and hard disk from www.ebuyer.com. Whilst span can sell disks in the enclosure you can save yourself a little money and buy seperatly from ebuyer and install yourself.
Enclosure:
http://www.macpower.com.tw/products/hdd3/pleiades/pd_scombo
Hard disk:
http://www.samsung.com/global/business/hdd/productmodel.do?group=72&type=61&subt ype=63&model_cd=249&tab=fea

Hard Drive Speed Difference Between FireWire 800 and Internal Drive

Right now I have my entire 1.5 TB Lightroom photo library on an external drive connected to my new Mac Pro via FireWire 800. Will I experience dramatic or even noticeable speed improvements if I move this drive to one of the internal SATA hard drive bays in my Mac Pro?
I would likely buy a new drive and SuperDuper the external to this new drive I put in the Mac Pro.
Thanks,
Matt

SATA II 3Gb is only the controller bus and has almost nothing to do with actual individual drive speed. Confusing the bus interface with hard drive speeds is not a clear way to compare.
Just pull the drive out of the FW case is all you probably need to do. Actual FW800 is less than 80MB/sec and more like 72-75MB/sec - which is as slow as your hdd gets from slow inner tracks.
Other than green, most 1.5TB drives average minimum 75MB/sec to max 115 with average in mid-90s. And the first 1/2 of a drive is where best performance comes from.
The size of the data and media library, amont of free space, all play a role.
I think FW should be left to backups, an alternate boot volume, off line data.
If it was Aperture library, but otherwise SSD is not realistic or viable. Nobody uses RAM disks as they are inefficient.
I still find 10K VelociRaptor ($279 / 600GB) fast, smoother, more responsive, great for system and data drives, even if they are only 135MB/sec, or about what some of your 2TB drives can offer.
QUICK TAKES - A striped pair of Velociraptor 600G 10K HDDs matches the speed of one SSD. For less that the price of one 256G SSD, you can buy two 10K 600G Velociraptor HDDs. If you stripe them (RAID 0), you get the same sustained transfer speed as the SSD. http://www.barefeats.com/quick.html
If you are not already using all the internal drive bays, just nice to have them handy before going external. Also take a look at two other articles on Barefeats:
THINK INSIDE THE BOX: Internal Storage Innovations for the Mac ProOctober 6th, 2010
EXTERNAL STORAGE INNOVATIONS for Mac Pros -- (Added results for ATTO R680 SAS RAID adapter.)

External Firewire as Main System Drive...

anyone have any comments on using an external Firewire drive as your main system drive? the stock 80GB internal drive in my mini is filling up at an incredible rate, actually had to offload my entire iTunes library just to clear some space, so i was thinking of using my 200GB Maxtor as my main system drive. any doing this? seeing any performance benefits and/or problems? thanks for any info.

from what I've heard from many articles re: MacMini before buying one for my GF, booting from an external FW drive (provided it's 7200+ RPM) you should notice a dramatic difference in performance.
place your install disc in the optical drive restart holding "C".
select the FW drive and use the Archive and Install option from your advanced tab before commiting to the install.
you keep your info on the drive and you get a faster machine!
if you decide to use the built-in drive to boot from make sure that you "re-bless" the internal drive from system preferences or you'll encounter an error screen the first time you try to boot with out the FW drive attached.
have fun with your faster mini!

LaCie 500GB External Firewire 800 causes crash every time its plugged in???

My LaCie 500GB Firewire External hard drive causes the computer to freeze every time I plug it in.
I just switched back to Mac from Win XP, where the LaCie was used for almost a year without a single problem. Supposedly, since it is formatted for XP use, it can simply be plugged in to my G5 (dual 2.3, 4BG RAM) and work just fine.
I've upgraded to 10.4.4 and still have issues. I've read this is a 'kernal panic' issue, etc.
What is the solution? I can't even plug it in and reformat it - as soon as it's plugged in the Mac collapses; the screen goes 'grey tinted' and an error message appears telling me to hold down the restart button and restart the computer. If I leave the drive plugged in, as soon as I've signed in on the restart, it crashes/freezes/collapses again, same error (i.e. it's circular).
There seems to be no solution. Any help MUCH appreciated!
Thanks,
Sarge

Welcome to Apple Discussions!
First find out if this is a Firewire 800 or 400 problem. Try connecting a Firewire 400 cable to the drive if it supports it. If it only has Firewire 800 ports, you may want to get a Firewire 400 drive to experiment to see if that's all the problem is.
After a forced reboot, it is also always wise to repair the directory if you are backed up:
http://docs.info.apple.com/article.html?artnum=106214
If it detects issues on your source drive that it can't repair, and you are backed up, then I would use Alsoft Disk Warrior.
If it detects no issues, then the problem probably resides in either the cable or the drive you are connecting to. Try a little process of elimination.

External Firewire 800 HD's

just wondered if anybody had any reccomendations for a external HD to be run on firewire 800.
I am going to be using this drive as a replacement to my current firewire 400 which carries my music production work, samples, and large sample library for my AU Instruments.
The firwire 400 seems to do the job ok but as I have the 800 I might as well make use of it.
I was looking at a couple the other night 1 being a Western Dig mybook pro and a lacie but up to that I havnt had a really good look.
If anybody has any comments then please let me know
thanks in advance
Fearny

My suggestion here;
http://discussions.apple.com/message.jspa?messageID=3935742#3935742

New Maxtor External Firewire 800 200 GB Drive Install Help

Similar Messages

Maybe you are looking for