New Neo 4 Platinum Wont boot past WIN XP :(

Hi, Im hoping someone can help me, I just built my system, its
MSI K8N Neo4 Platinum
AMD 64 3200+ 939 0.09
2 x PC4000 Crucial Ballistix (running at 200mhz)
4 Lighted Fans, Lighted case,
DVD RW, CD ROM ,
Floppy with Multimedia,
XFX Geforce 6600GT 128mb
Antec Trupower 430w 26a on the 12V, 36A on the +5V and 28A on the +3.3V
Ok, Everything works fine, till WINDOWS boots up ... And it wont boot, before the windows XP loading screen, it stays black, and freezes.. now.. to me it seems like memory/ power supply issue. lowered timings, raised Memory to 2.8v (Crucial suggest this voltage for the ram) ... no go... now my power supply is a good power supply.. but its only 20pin, and the nforce 4 ultra (well MSI) is 24pins ATX 2.0.. mine is a standard ATX12V... its supposed to still work, but Ive had mixed bagss of peopel saying it worked for them, and others that said it didnt.. but with this power supply, shouldnt I have been fine.. PLEASE someone help me, this is eating me alive...

Oh man this sounds familiar., i'm having some of the same probs. I just redid the install of XP Pro sp2 cause i needed the nvidia raid drivers for the NCQ on the Seagate i got.
The first install went fine but i couldn't oc more then 220fsb with this Corsair pc4400, so
i was like ok let's just get everything running sweet and then play. So after i added the
printer a usb scanner and a usb memcard reader for the camera, it would just hang after the boot logo for xp then it would hang on the Platinum screen sometimes too.
So i played with the voltages which seemed to help for a little bit., i went 3.3%+ on the cpu, 1.5 on the north bridge, and 2.70 on the mem. So i reformatted and used the 6.39 chipset drivers and the latest vid drivers from the manufacturer and everything seemed ok. So i proceeded to add the printer, scanner and card reader again 1 at a time and it seems like it's after the mobo gets warmed up is when it hangs on booting XP after the bootscreen., Cpu temps are at 35C and this mobo in a Cooler Master Cavalier case runs kinda warm for me like at 36 - 37C (According to Cool n Quiet) after it gets all warmed up. So i'm kinda at a loss here too. I got the same psu as the first poster. Memtest 86 ran for 4hrs, with no errors, and Sandra burned in for a couple hours with no problems.
Oh and the mobo say's the bios is the 1.1 dated 1-12-2005
So i'm hoping it's a bois thing that will be resolved soon, or is it this psu. Seems like some other fellas have had no probs with lesser psu's. Oh and do those 20 to 24 pin adapters make a difference?

Similar Messages

New Build P7N Platinum wont boot issue

Hi Guys,
First of all can i give you all the spec of the machine i am having the issue with a s its NOT the same one as in my signature.
P7N Platinum (not sure on bios versions as i cant get to it!)
OCZ 8500CZ memory (2x2gb)
E8600 cpu with Arctic 7 cooler
tagen BZ series 900 watt PSU
Problems are as follows:
I have just assembled the system for my wife and when i powered up for the first time i got into the bios no problems. I changed the voltage for the memory as it runs at 2.1 volts and changed the date and also the boot priority settings to DVD drive first, then HDsecond and saved as i wanted to install an OS on reboot.
I rebooted and started to install XP but it froze during the format of the drive section.
When i now try and reboot i am getting nothing at all. The screen stays black but CPU fan spins and goes at normal speed as does the rear case fan. The PSU lights up and the GFX card fan is spinning.
I have tried running just 1 stick of memory but this has not worked or made any difference. All the normal Motherboard lights appear to be on.
Can i also point out that on the first boot ( when i forgot to check what bios version i was running) the E8600 was recognised in the bios with the correct multiplier and speed. This is my first complete build and i was wondering if i have missed anything obvious
I need some help now as i diont know what to do.

Quote from: DaLoona on 03-May-09, 21:26:43
Edit :
Did you try to clear CMOS with pc unplugged?
Be sure to turn off/pull the plug of PSU & hit the case power switch to drain PSU/MB capacitors before you clear CMOS. That should restore factory BIOS settings so you can at least boot to BIOS again and see what revision you have. You can also lookat the sticker on the BIOS chip, last 3 digits indicate version ie 100 would be v1.0,
110 = v1.1. For your CPU you should have v1.2 going by CPU support list.
I'm pretty sure the chip is located here on your MB:

Macbook pro a1150 wont boot past kernel, stuck on gray screen.

got a macbook pro a1150 ati 1600 gpu. last for characters in sn are vww. will not boot past gray screen after the gray screen with the apple logo. it has a fresh install of 10.6 on a new hard drive from a laptop of the same exact kind. when in target mode and its Hard Drive used as a boot divice, it will boot. no broken graphic on startup with the apple icon and the pin wheel spinning. boots to safe mode just fine, will even do updates. but will not boot from the NEW hard drive or the dvd rom. when i put the old hard drive in with 10.5 it wont boot past the blue screen and the same with the 10.5 install disc i baught. reset pram, changed ram, removed wifi card and even tried disconnecting the dvd rom but still will not go to the login screen. even disabled auto login (when it was in target mode). do i reflow the gpu? is it a gpu problem? one thing strange.... in safe mode, lines show up on the mouse icon and just that. the rest of the screen shows everything fine, i've seen this before with the nvidia chipset but not with ati. how do i fix it?

to better explain... the macbook pro in question never get to the blue startup screen which happenes before the login menu. not though dvd rom, hard drive, external dvd rom or external hard drive. just stop there. i hear the hard drive working / dvd spinning and the computer reading the disc but after a few min of just seeing the grey screen both would spin down.

Power Mac G5 wont boot past the Apple Logo

Mac: Power Mac G5 2.7Ghz DP w/ 4gb RAM (2x1gb, 4x512mb), Leopard
Last week, I formated this computer and reinstalled OS X 10.5. I updated everything, reinstalled all my applications and replaced my documents. Everything was good for a couple days. I have and HP 1350 all-in-one printer (which HP no long has mac support for that model, so I can only use the scanner as a photocopier, but that's not the issue, it prints fine and I have printed files since the formatting) The printer is connect via USB to my Power Mac and then shared on my home network, wirelessly, with 2 other MacBooks and a 27" iMac. My roommate was trying to print something from his MacBook. In the printer queue on the MacBook, the file would say it was printing, but nothing would actually printer. When I went to the printer settings on the Power Mac, the dialog box said the printer was "in use." I reset the printer, nothing happened. I restarted the Power Mac, properly, and now the computer wont boot past the Apple logo. The spinning gear appears and spins for a minute or 2 and then it will just reboot on its own. It will just keep doing this in a continuous loop.
I've tried to boot into safe mode (holding shift) but it still does the same thing.
I manage to get the CD drive open by booting into open Firmware. I restarted the computer and was able to boot from the Leopard disc. I ran disk utility, and repaired the drive and the permission but everything was ok.
I've unplugged any USB device connect but to no avail.
I really don't want to reinstall Leopard again. it took almost 8 hours to install all the applications (such as Logic, Komplete 5, etc) and I had not setup time machine. There are some document files that I would prefer not to loose, but could deal with the loss.
any suggestions?

Ok, so I reinstalled Leopard, all my documents were in the "Previous Systems" folder, and the applications where present. I went to Software Updates to download all the need updates, which included 10.5.8, itunes, security fixes, etc. It notified my that I would have to restart. I click ok, everything was logged out and the updates started installing. As the computer restarted itself after the updates, i had the same issue again, where it would go to the Apple logo and then restart itself. The second time around, it just froze and the warning "You need to restart your computer" with the power logo in the background came up. So I manually restarted my computer and everything logged in correctly. I restarted it a couple time to see if I could duplicate the errors but everything keeps working properly. Now I'm kind of scare to restart my computer.
Any suggestions as to why this would be happening? Is this most likely a software issue or a hardware issue? This never happened before I formatted last week. The last time I formatted the computer prior to that was less than a year ago.

I tried to update my ipod touch to ios 6 and now it wont boot past the apple icon. please help

I tried to update my ipod touch to ios 6 and now it wont boot past the apple icon. please help

Put your ipod in recovery mode and then restore your software again.

2010 MacBook wont boot past grey screen, even after a new hard drive and install CD.

Hey guys, I received a 2010 Macbook last year as a gift (no warranty). It worked fine untill a few days ago. It wouldn't boot past the grey apple logo. I took it in to an Apple store and they said it was a bad HDD. Since I didn't have much stored on it, and I have everything backed up to my desktop, I got a new, larger capacity HDD and replaced it with no issues. I started the Macbook with the OSX Leopard install CD, but it didn't identify the HDD, and now it won't boot past the grey screen.
Any ideas? Is it the motherboard?
Thanks a lot!

House3917 wrote:
I started the Macbook with the OSX Leopard install CD...
Leopard is done for, call Apple via phone and order the 10.6.3 white retail disks and use those.
Use these install instrcutions for best operation and performance.
How to erase and install Snow Leopard 10.6

Imac G4 wont boot past grey screen desperatly want to fix it!!!!

Hi there,
Please can someone help.....
I got a Imac G4 at the weekend for a bargin, but it wont boot up. When i turn it on it makes the noise and comes up with a grey screen with the apple logo and the loading circle. It doesnt go past this screen and after about 15 mins turns itself off.
Any ideas how i can get this running again (havent tried anything yet to be honest as im not sure what to do). I love these machines as i just think they are querky and would love to get it working again to use as my home pc (as even though its old it will still probably be quicker than my old microsoft laptop)
Thanks!

Did you try a PRAM reset?
http://support.apple.com/kb/ht1379
>I can't get the disk drive to open either
If the optical drive tray cannot be opened, what happens if you hold down the mouse button during startup?
As a brody indicated, a faulty hard drive cannot be ruled out. Instructions for removing this drive can be found in the ifixit.com guides as well.
If you can gain access to the optical drive, the best way forward would be to use an appropriate Mac OS X system CD in an attempt to start from that disc (holding down the C key).
If it is not possible to locate a correct system CD right now, another way could possibly be to try to boot from an Ubuntu CD for PowerPC instead (once again, holding down the C key) just to see whether the computer is capable of booting at all.
Jan.

PXI wont boot past BIOS, strange characters displayed (possible HDD failure)

I've just acquired a PXI-1042 with a much older 8186 Controller which does not boot past the BIOS.
Once powered up the sytem recognizes the HDD and available ram and even does a ram check but then it displays some strange characters; what appear to be "AC" and two dos smiley faces.
CMOS battery has been changed and system time has been updated as well. HDD is recognized in bios and is selected as the boot priority.
This could be a bad HDD since I know nothing of functionality of this PXI, other than its "hardly been used".
Just figure I'd ask around before going through the trouble of purchasing a new drive through IT.
See attachment for screenshot.
SCXI- 1000 Chassis w/ 1346 adapter
PCI 6281 DAQ card
SCXI- 1520 Bridge Board w/ 1314 Terminal Block (x2)
SCXI- 1180 Feedthrough Panel w/ 1302 Block
Signal Express 2014.
Win7 Enterprise
Attachments:
PXI.jpg ‏34 KB

It's possible the drive is fine, but just does not have an operating system installed. If this PXI-8186 controller originally shipped with Windows, it may have an OS recovery partition. This KnowledgeBase article is a good reference: Hard Drive Recovery and OS Installation.
If you want to check the integrity of the drive itself, here is another relevant KnowledgeBase article: Hard Disk Drive Diagnostic Tool for PXI and PXIe Embedded Controllers.

Wont boot past grey screen after disk access was changed

I have a new 13" macbook pro with OS X Lion. I changed the hard disk access from read only to no access, walked away for a minute, when I came back my computer screen was black. Upon touching the mouse pad the mouse arrow showed up but the screen stayed black. I preformed a hard shutdown and when turning it back on it wont load past the grey screen with the apple logo. Ideas? Solutions? Please help.
Thanks

please explain exactly what you did.

G5 wont boot past white Apple screen.

To anybody that may have some advice. I hadn't used my power mac in about 4 days then when I turned it on last night it wouldn't boot past the white apple screen. I still have the chime my fans and processor still spin up. I tried resetting the SMU, and I also took out 3rd party ram I had installed and tried booting up to see if that was the problem. I'm prepared to take it to the apple store, I just thought somebody might have some advice before I take it there. So again when I boot up it reaches the white screen with the grey apple and then it just gives me the little grey spinning dial and just spins and spins. Thanks in advance to anybody with any advice.
Dual 2.0 GHz Power mac G5 Mac OS X (10.4.8)

Well first I booted holding option and it just booted into target disk mode or something like it, a screen that would allow me boot from a different drive if I had one that was formatted with Tiger. So then I rebooted holding >shift and OPtion. And it kernel paniced, it said it didnt have the driver for this version Tiger 7,2 or something along those lines and then it gave me apples screen of death asking me to restart.

My hp ProBook 4510s wont boot past the windows logo

my laptp doesnt boot past the windows logo, it just shows the windows logo but thats it, it doesnt get past that, I have tried the hard rest, took out the battery and the poer cable, even did the safe mode thing but nothing works...please help me fix this problem

I'd recommend testing the HDD:
tap F2 at startup
select either hard drive check or component tests then hard drive
run a quick test
if this fails then the HDD will need to be replaced, otherwise, I'd suggest a full system recovery:
tap F11 at startup
Win8:
select Troubleshoot
select Recovery Manager
select system recovery or minimised image recovery
follow on screen prompts
Win7:
select system recovery or minimised image recovery
follow on screen prompts
*****I do not work for HP*****
*****click the purple thumbs up button to say thanks*****
*****If I solved your problem, help others by clicking accept as solution*****

Laptop wont boot past Toshiba screen

I have the Satellite c855-s5123. I shut it down and when I went to turn it back on it wouldn't boot past the initial startup screen. The Toshiba screen came on, it said it was repairing (i believe that was the word it used) the C: drive. It began counting up with % until 100% then went on to the blank screen (mine is pink) that always comes up when booting up. After that it turned black, then blue back and forth and never went on to boot like normal. I don't know anything about computers. The only thing I did after this was press control alt delete...when I did this a message came up that said "the instruction at 0x04fe9006 referenced memory at 0x0000001d. the memory could not be written" and an "okay" box to click. i clicked okay and it went back to switching from blue to black blank screen. I turned it off and on once again and this time it didn't have the repair C: it just went to the Toshiba screen then straight to the black and then blue once again. I have only had my laptop about 8 months and I take perfect care of it. I have no idea what is going on. And as I said earlier, I know nothing about computers. Any help would be appreciated!!

Try the Troubleshooting Assistant or the suggestions in this article.
What can I do if my Windows 8 laptop won't start?
- Peter

IMac wont boot Past Grey Screen, finder folder with blinking question mark

iMac G5 won't boot Past Grey Screen. The G5 froze and i restarted, It will not go past the grey screen and it has the finder folder with blinking question mark, also the fans kick on wide open. As it atempts to boot a sound plays "beepda beepda beepda beep" that starts quiet and gets louder and repeats a couple of times. I ran a hardware check on the startup disk and all hardware passed. I thought it might be the RAM any suggestions?
I have restarted using the troubleshooting methods in the guide.

Sorry for the late reply. The drive shows up when booting to disk, but it will not allow you to verify disk or repair. Also it will not allow you to select the hard drive to reinstall the software. Under disk utility Maxtor sabre shows up with total capacity:0 bytes.
I've taking the Mac to the Apple store to get looked at, and its probly the hard drive. Now Im trying to see if theres a way to recover the data myself. I've used software like "Data Rescue" the hard drive shows up "Maxtor Sabre" totally capacity: 0 bytes, and it will not recover anything.
Did this test just to see if it was power problem.
http://support.apple.com/kb/HT2173
Thats when noticed the beeps are coming from the hard drive. So its getting power.
Now just wondering how to recover data.
Any suggestions?

MacBook Pro: Tiger wont boot past grey apple screen w/ spinning gear, HELP!

Hey everybody,
I have a 1.83 Ghz MBP with 512 mb of RAM (lame I know). The other day someone was using my computer to burn a CD on iTunes when all of my programs began failing. On instinct I rebooted my computer to solve the problem. Alas, now I cant boot past the grey apple screen, and the gear is spinning away. Saddest part of the story is that I had time set aside to back up my computer the day after this happened . Anyway what is the best thing to do from here? I haven't made any moves to fix it yet really, so what is the best thing that I can do to try and get my files back?
Thank you,
Sam A.

Hi, I posted to you in yoour other thread.
I very much doubt Disk Utility or fsck will fix an +Invalid Node Structure+ error. That's a pretty serious error and DU is just not robust enough of a utility to repair it.
If Disk Utility can't fix it, you'll need a more robust utility for the repair. I would recommend DiskWarrior. It is the best at directory repairs. It rebuilds then actually replaces your old directory. I feel every Mac owner should have a copy. Make sure you get the disk so you can boot up on it to run repairs. You can also install it on another drive and run it from there to repair this one. DW works faster that way.
I use DW once a month to try and catch errors in my system from getting too far out of hand.
If you have a good backup, hopefully a clone of your system before you had issues, an Erase and Install will also rid you of this issue. But, beware! You will lose everything on the drive with this procedure. Let us know if you need help with that!
Cheers! DALE
p.s. If the +Invalid Node Structure+ is real bad, there's a risk even the mighty DiskWarrior will not be able to help. Normally it will come thru; it's only in the severe cases it won't be able to do it. If you don't have a backup, and need the data bad, it's worth the try!

K8n Neo 2 Platinum Board Booting issues

# CPU brand, model and speed (E.G. AMD Athlon64 3000+ 'Venice' core) AMD 3800+ Not sure of Core
# Motherboard model (E.G. K7N2 Delta2 Platinum, NOT just MS-6570!!) K8N Neo 2 Platinum
# Memory brand, type/speed, size, number of sticks (E.G. 2x Crucial 512MB DDR400) Kingston KVR400x64c3a/512 x2
# Video card brand, chipset type, memory size (E.G. Gainward Geforce 6800GS 512MB AGP) ATI Radeon 850 Pro 256MB AGP
# Hard drive(s) brand, size, type, speed (E.G. 2x Seagate 200GB SATA150) 2x Hitachi 80GB SATA150
# Any other peripheral cards and devices (E.G. MSI TV@nywhere Plus TV card, MSI DigiVOX USB2 TV tuner) D-Bracket 2
# Operating system and version (E.G. Microsoft Windows XP Home Edition SP2) Windows XP Sp2 / Ubuntu 7.10 / Vista Ultimate
# Power Supply Unit brand and output in watts and DC output (amps) TurboCool 510 ATC-PFC ( Taken from a Vapochill SE Chassis ) Originally had been Tagan TG480-U01 however it just blips the power on and off so thinking it is faulty.
I have replaced my motherboard as I had thought it originally was a duff BIOS chip as despite reflashing it, it would rarely pass the POST.
All parts apart from the PSU are the original Kit which had been working for 13 months ish.
Problem i am experiencing is the D-Bracket 2 Diagnostic LEDs are coming up Red/Amber as opposed to Red/Green and the machine just sits there and never displays anything, hence why BIOS isn't mentioned as I have no idea what version is currently on the BIOS chip.
I have stripped out down to just CPU and still get the same problem, I then swapped it for a FX53 which I had lying around which I know worked as it came out of my Vapochill chassis and also swapped out for some OCZ PC3700 512MB EB Dual Channel Platinum 3-3-2-8.. still no joy.
Any ideas greatly appreciated as I don't want to rebuild my machine as it is exactly how I wanted it I feel I have checked everything but maybe someone can shed a little light.
Anyone want a spare mboard or two ?? I now have three !

Your Tagan's behavior was typical of a failing PSU... but the Turb-Cool model you mention doesn't exist at the PCP&C web site; in fact there are a total of five other 510 models, some of which have only an 8-pin CPU power connector, so it's impossible to figure which one you have. Does your PSU have a 4- or 8-pin CPU power connector and, if the latter, how do you have it connected to the mbrd? The only 8-pin CPU power connector I've seen could not be connected to a 4-pin socket, which your mbrd has... or does your mbrd have both 4- and 8-pin?
The only other thing I'd remark is that Vista will not run satisfactorily with your nForce3 mbrd and an ATI video card.

New Neo 4 Platinum Wont boot past WIN XP :(

Similar Messages

Maybe you are looking for