New Netgear Router and hp1022nw

After getting a new Router - a Netgear WNR3500v2, i dont seem to be able to get my normally trusty 1022nw to connect to my wireless network.
When i connect to the printer via Ethernet via its fixed IP address 192.168.1.33 i can see the wireless network but it just refuses to connect.
Im using WPA-PSK [TKIP] + WPA2-PSK [AES] Auto Channel up to 54Mbps.
The router only gives DHCP upto 192.168.1.32
Any ideas? Its driving me crazy.
Thanks for your time. Warren

No trouble and thanks for your reply.
Ive checked all those things. The Router (a Netgear WNR3500v2) is running the latest firmware (V1.0.2.10_23.0.70) and is also working in 'Up to 54 Mbps' It says its: a Legacy Mode, with a maximum speed of up to 54 Mbps for b/g networks. Ive fixed the channel to channel 1.
Ive changed the Encryption on the printer in the Networking/Wireless tab to 'Disabled (No encryption)' with the Ethernet lead plugged in and then unplugged the lead. The blue light now lights up (that's a first), but it doesnt repond to the the fixed IP ive given it in a web browser or print anything. On the test runout (after a power cycle) it says:
IP address - 0.0.0.0
Link Status - No link
All Packet infos are at 0
802.11 Wireless
Wireless Status - Enabled
Communication Mode - Infrastructure
SSID is my network
If I then plug the ethernet lead back in and wait for the blue light to go out, then do another test runout i get:
IP address - 192.168.1.33 (fixed address i gave it [DHCP only runs upto .32])
Link Status - 100TX Full
All Packet infos are at small but +ve numbers
802.11 Wireless
Wireless Status - Disabled
Communication Mode - Infrastructure
SSID is my network
Ive also checked the firware on the printer and its 20061215
It says Wireless Radio Datecode 031705 if that means anything to you.
Did you want me to send the details of the setup on the HP printer?
Is there a way to dump the info to a log file?
Any more ideas?
W

Similar Messages

New Netgear Router and now I can't get a wireless connection for my K5400 printer.

I got a new Netgear Router and now I can't get a wireless connection on my Officejet Pro K5400 printer. Anyone know what I can do to fix this. Using Windows XP

On the printer: Setup > Network > Restore Defaults. From the same Network menu, run the Wireless Setup Wizard.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

AIrport Express and my new NETGEAR router

I have two airport expresses hooked into two stereos in my home that show up with a green light in airport utility. My new netgear router,NETGEAR dual band WNDR3700 is connected to my PC and my itunes are on my IMac. The airport connection from the Imac to the router is great. Fast internet. My iTunes are, however, not playing on the stereos with the airport expresses even though the green lights are on....is this a security thing....? The new router is great for the internet-faster than ever but I would really, once and for all, like to get the airport express thing working and stable. my old router kept losing signal so I am hopeful that this new stronger one will work better. I am guessing that since I have green lights I am almost there. Thanks for the help.

I'm having a similar issue. Have you figured anything out yet?

New Netgear Router slowed broadband speed

Hi,
Was wondering if anyone had experienced this before- I decided to "upgrade" my router from my old BT home hub that has numerous cracks/wounds on it from bouncing off my floor over the years to a new Netgear N300 wireless router. I was able to install it ok and have checked all the connection settings incl for wireless use which seem to be correct and as recommended. I live a long way from exchange and my usual speed is **bleep** anyway (0.5mps) but with the new netgear router it can now take several minutes just to load a webpage (ie it is un-usable) and this was when it is directly connected to my computer. It would be intended to be used wirelessly but speeds where even worse when I tried it wirelessly. I am preparing to take it back to store but wondered if there was a reason for it as thankfully by old BT hub still works but it cant go on forever!!!

can you post any adsl stats from your netgear - used to be router status and then statistics at the bottom but may have chnaged in new netgear
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

I currently have a WPN824 v3 Netgear router and I'm trying to set up my Apple TV. I'm able to connect it to my wireless network but my airplay feature is currently not working.

I currently have a WPN824 v3 Netgear router and I’m trying to set up my Apple TV. I am able to connect it to my wireless network but my airplay feature is currently not working. The icon does not appear on any of my devices. My ipad and ipones all are currently up to date and are all joined to the same network. Is it the way that my router is configured. Please help let me know what I need to change in my router settings or does my router not work with Airplay. Or is there a simple fix.

you don't mention which products you use
only ipad2 and up support mirror
and only iphone4s and up support mirror
other devices only use airplay for apps which support tvout options

I installed a new wifi router and airport will not connect automatically to it. It sees the network but will not connect unless I tell it to.

I installed a new wifi router and airport will not connect automatically to it. It sees the network but will not connect unless I tell it to. I can't find anywhere in the utility or network preferences that will allow me to choose this router as the default. How do I fix this? BTW I'm using Lion.

Are there any previous networks that you have used that have the same password as Molly? YES
Using System Preferences > Network > AirPort Advanced again, you need to remove any listings of previous networks that used the same password as Molly. Click the name of the network and click the - (minus) button at the bottom of the list of connections.
Also delete any other networks (except Molly at the top of the list) that might have used the same name...Molly in the past.
Delete any other networks that you no longer need so that your Mac will search for networks more quickly
Click OK, then click Apply
Open KeyChain Access and look for a listing of any old networks that you no longer need. Click to highlight the name of the network, then click the Delete Key on your computer.
Then look for any old networks that might have used the name Molly in the past and do the same for them.
Then look for any old networks that might have used the same password as the password for your "new" Molly network and delete them in the same way
Click the KeyChain Access menu just next to the Apple icon in the upper left corner of the computer screen
and then click KeyChain First Aid
Enter the main administrator password for the Mac you are using and highlight the Repair button. Then click Start. You will see a message that repairs have been completed
Quit Keychain Access
Power down the entire network...all devices...order is not important
Power up the modem first, then your main router, the other devices one at a time
Log on to Molly and see if the Mac remembers it after a few tries. If not, I'm afraid that you will need to change the name of the wireless network and password on your router due to corruption issues on the Mac. You have done everything possible without re-installing the complete operating system.

I have a new WRV210 router, and set it up fine - works as...

I have a new WRV210 router, and set it up fine - works as expected for about 5-10 hours then hangs - pull the power, and restart the device it works again. This is getting old fast.
I use if for a VPN ipsec tunnel - tunnel works great when it is working.
It is also used as a NAT behind an AT&T router getting a DHCP address for the WAN connection.
It has the latest firmware as listed on the web site 1.1.16
I was thinking about reflashing the firmware - any suggestions?
Steve

Hey try resetting the router reset button in such a way that power
light is blinking on the router & then do a complete network power
cycle i.e., unplug the power cables from the modem & from the router &
then plug in the power cable to the modem first once all the lights are
solid green you could plug in the power cable to the router & check out
it will definately work!!

Connect Modem, Netgear router and 2 airports

I have a modem and separate netgear wireless router supplied by comcast. Would like to set up a wireless network using 2 airport extreme base stations, each connected via ethernet to the router.
Is this possible? I assume that both airports would be in bridge mode, each connected via ethernet to the Netgear router and then the router connected to the modem?

Welcome to the discussions!
+Would like to set up a wireless network using 2 airport extreme base stations, each connected via ethernet to the router.+
+Is this possible? I assume that both airports would be in bridge mode, each connected via ethernet to the Netgear router and then the router connected to the modem?+
Sure, it will work fine as you describe. You'll need to configure each AirPort Extreme to "create a wireless network" and setup security and a password for each device.
You have the option of configuring two separate wireless networks, or if you assign the exact same wireless network name, security and password to both AirPort Extremes, you will in effect create a large "extended" network.
This is called a "roaming" network because computers will automatically connect to the wireless access point with the strongest signal as they "roam" around the house. As in the above example, both AirPort Extremes would be configured in bridge mode in this type of setup.
Post back if you need any more details about this.
Message was edited by: Bob Timmons

New Netgear router/Iphone3G

Installed new Netgear router. Connect to the internet via OSX 10.4.11. My 3G is showing wifi symbol, but every time I try to connect to Itunes/Youtube it reverts back to 3G. When I go to wifi settings it clearly states that I'm connected to my network. We have been using Belkin router up until now no probs. I'm lost. Any help please?

Your question doesn't seem to have anything to do with the AirPort Extreme base station (AEBS). I suggest that you post in the iPhone discussion area.

Connecting HP 4500 Wireless printer to a new Netgear router/modem

When running setup from the wireless config screen on the printer it finds my new router/modem and then asks for the WPA passphrase. I enter the one that came with the new router and it comes back as a fail. Is there a secret around this or another passphrase it is looking for? I had this printer on my older modem before and it was connected to all PCs in the house but the new one does not want to connect. Thanks

how did you make out with this issue as i plan to buy the 6480

Airplay not displaying on iphone since getting new Netgear router

Hello, I had no problems running airplay through my phone through my apple tv onto my TV when I used AT&T internet and router. Since I changed to Charter internet and their Netgear WNDR3800 router I can't get the airplay to display on any of our phones. I have gone to www.routerlogin.net and confirmed the right boxes were unchecked for Enable Wireless Isolation and still the Airplay button will not show up. Not sure what I'm missing??

Do a quick Google Search, there are pages of people complaining about that router and airplay
Click this link

I have a new wireless router and now my laptop will not recognize the printer.

I recently installed a new wireless router,Linksys E2500, and now my laptop will not connect to my OfficeJet 4500 wireless printer. Operating system is Windows XP. Says it does not recognize the printer. It was working fine with my other Linksys router and I have been able to connect all of my other electronic equipment. Thanks.

You must reinstall the full feature software and drivers again to be sure it will work with the new router. This is the fastest way. Simply follow the instructions that came with the printer.
Say thanks by clicking the Kudos Thumbs Up to the right in the post.
If my post resolved your problem, please mark it as an Accepted Solution ...
I worked for HP but now I'm retired!

Unable to connect to netgear router and internet

I've installed Solaris 10 1/06 (x86) on a system running an intel mainboard model D865PERL. This has a built in ethernet controller ( Intel 82547EI gigabit lan controller) and the mainboard appears on the bigadmin hcl as being supported. The OS recognizes the built-in NIC as e1000g0 but during initial installation it attempts to configure e1000g0 first thing then responds with "skipped interface e1000g0" then proceeds with the installation.
I choose Networked and run through the installation (or following a sys-unconfig) selecting to enable DHCP but it returns "Could not contact a dhcp server on the network interface e1000g0." I then have to set it up staticly to resume the configurator. I specify the e1000g0's ip address as 192.168.0.5 with a subnet mask of 255.255.255.0. I choose not to enable IPv6 (ive tried it with IPv6 enabled) and no Kerberos. I attempt to specify DNS for name service and use my internet providers domain name (both the name and the resolved ip address associated with it) with the two DNS server ip addresses resolved by the WAN setup on the router (Netgear FR328S), selecting no search domains. But it is unable to locate my hostname on the provided DNS's i entered. dunno why it would say that, it really doesn't matter does it? Anyway, I specify no name service to proceed. i choose no to the question in regards to overriding the system's default NFS version 4 domain name to continue.
It knows it has a cable connection but I'm unable to see the router, even though ive specified 192.168.0.1 as the default route (ive also tried setting it to detect the default route on reboot but it fails). The router doesn't see the NIC as a connected device either (im setting here on another computer running xp :() Ive tried disabling the DHCP server feature on the router and I still cant see it. Ive tried setting the NIC's ip address and MAC address as reserved in the LAN setup on the router (this works for my winXP drive where I need a static IP address and also have access to the internet). I've tried leaving the reserved IP address assignment (attached to the NIC's mac address and host name that i specified) with DHCP enabled but I'm still unable to resolve an IP address from the dhcp server. I made sure the router had the latest firmware and went through the configuration with a fine toothed comb, so to speak. nothing seems to work.
I tried to connect directly to the internet device, removing the router and it still fails to resolve an ip address via dhcp. what am i missing here? Ive run through this multiple times now and im at a loss. Ive also referenced sun's System Administration Guide: IP Service to try to resolve the issue but im now all I'm doing is going in circles.
# ifconfig -a
lo0: flags=2001000849<UP, LOOPBACK, RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
e1000g0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 192.168.0.5 netmask ffffff00 broadcast 192.168.0.255
ether 00:13:20:47:6c:48
# netstat -rn
Routing Table: IPv4
Destination Gateway Flags Ref Use Interfacd
192.168.0.0 192.168.0.5 U 1 0 e1000g0
224.0.0.0 192.168.0.5 U 1 0 e1000g0
default 192.168.0.1 UG 1 0
127.0.0.1 127.0.0.1 UH 4 85 lo0
# prtconf -pv
Node 0x000019
compatible: 'pci8086,1019.8086.301f.0'.....etc
model: 'Ethernet controller'
subsystem-vendor-id: 00008086
subsystem-id: 0000301f
vendor-id: 00008086
device-id: 00001019
name: 'pci8086,301f'

Couple of suggestions:
Work first on seeing the router, using a static IP and pings.
Forget about DNS, DHCP, etc for now. If you don't see the router, nothing is going to work.
You don't need to reboot or do sys-unconfig every time. Just change your settings using ifconfig and route add. Actually, you don't even need to set the route to be able to ping something inside your subnet.
By your output of ifconfig, it seems that the NIC plumbed correctly.
In the Solaris machine, try pinging your own IP address to make sure it responds and you don't have any issues with the NIC/driver.
Make sure the cable and port in your router work. If you can use them with Windows, you should be able to use them with Solaris. Unless...
Try using a crossover network cable to connect the Solaris computer to the router. This is personal experience: I had a Blade 100 that would not see my router. After a couple of hours of trying just about everything, I used a crossover cable and voila! it worked. Why? I don't know :) , but it worked...

HT4199 I have a Netgear router and have just acquired a Edimax wifi extender. My MacBook Air sees the wifi signal and can get to the internet through the extender access point. However, while my iPhone and iPad mini can also see the WiFi signal, not Int

I have a Netgear WNR2000 router and an Edimax EW-7438RPn wifi range extender. I have gotten the range extender to work well with my MacBook Air, however, while my iPhone 3Gs and iPad mini can pick up the wireless signal from the range extender, they cannot get to the Internet through it. No IP Address, Subnet Mask, Router, or DNS appear in the details on either the iPhone or the iPad mini. How do I get the iPhone and the iPad to connect to the Internet. It seems that the problem is with the iPhone and iPad, since the MacBook Air works just fine with this set up.

Junglemania,
Go into the setup page of the EW-7438RPn. Go to Wireless Advanced Settings. There is a WMM settings. Make sure the WMM is enabled.
This may help you out.

Netgear router and airport express

hi
could someone please help me and tell me(in very simple terms!) how to extend the range of my network. my mini mac is too far away from my netgear DG834GT router and have been trying for days to use a/ex to reach it.Have tried everything i know which i freely admit isnt much but airport utility doesn't seem to see the router. i have seen people having similar problems but am hoping someone is out there to take me through it in words of 2 syllables or less! help

charlie117, Welcome to the discussion area!
The Netgear device is not compatible with Apple's WDS. Therefore there is no way to use your AirPort Express (AX) to wirelessly extend the range of the Netgear.
You could run an Ethernet cable from the Netgear to the AX. Then the AX would create a wireless network at it's location which would be an extension of the Netgear's network.

New Netgear Router and hp1022nw

Similar Messages

Maybe you are looking for