New network and modem - new settings for Extreme Airport?

Moved to a new country, new cable internet setup. Get direct conection with line from G-5 to modem to cable but not with Extreme Airport. What do I need to do?
G-5 Mac OS X (10.4.2)

The cable modem has probably associated itself with the MAC address of the G5 Mac.
You need to blank the modem and then connect the Airport Extreme base station.
Turn off the cable modem for 30 minutes and then connect the base station, you may have to leave it longer or even overnight.
iFelix

Similar Messages

How can i obtain a new password for my airport if i forgot the original

trying to help my friend out..save her a trip to Apple store
she needs a new password for her airport it keeps requesting one from her...and she forgets her original
how can we set up a new one for her
thanks in advance

Go to Settings > Phone > Change Voicemail Password

HT4864 I am getting a triangle with an exclamation point next to my inbox...it says: There may be a problem with the mail server or network. Verify the settings for account "MobileMe" or try again. The server returned the error: Mail was unable to log in

I can send but cannot recieve email
This is the messege I am gewtting:
There may be a problem with the mail server or network. Verify the settings for account “MobileMe” or try again.
The server returned the error: Mail was unable to log in to the IMAP server “p02-imap.mail.me.com” using “Password” authentication. Verify that your account settings are correct.
The server returned the error: Service temporarily unavailable

Also if I go to system preferences accounts and re-enter the password it fixes the glitch sometimes.

I bought an unlocked Iphone 3GS, I needed to update Ios5 and restored the settings for that which was not authorised for unlocke, but after that iphone is not getting activate and no sim card insatlled error is there. i m using local sim card in Pakistan

I bought an unlocked Iphone 3GS, I needed to update Ios5 and restored the settings for that which was not authorised for unlocke, but after that iphone is not getting activate and no sim card insatlled error is there. i m using local sim card in Pakistan

You didn't buy an 'unlocked' iPhone 3GS - you bought a 'hacked' one.
Updating to iOS 5 removed the hack and the unofficial unlock.
All you can do is try to find out which network the phone is locked to and ask them if they can unlock it properly.
Otherwise, sell it or throw it away and buy an officially unlocked phone from an official source.

MSMP Workflow - Add new settings for Maintain Stages

Hello all,
I have a question: It is possible to add a new folder under "maintain stages"( "Eg. Settings for OVM Approval). See attached.
If yes, how?
Thank you,
Ovidiu

Hi Vimal,
here it is : http://help.sap.com/saphelp_45b/helpdata/en/2a/f9f542493111d182b70000e829fbfe/frameset.htm
For approvers & level determination, we can define it at spro.
SPRO- investment management(IM) - appropriation requests(AR) - control data - define partner determination & functions.
SPRO- IM - AR - approval - define approval levels for AR
Regards,

My mac mail is now offline. The pop up says There may be a problem with the mail server or network. Verify the settings for account or try again. Any one know how to get my mail back on?

I down loaded the new free os x yosemite today and now my mail is offline. Several pop ups that say there is no connection.
Verify the settings for account or try again.
The server returned the error: The certificate for this server is invalid.
I have not changed a thing and now I have no emails coming or going. Since it is my communication line to many of my clients, I am in need of some answers asap.
Thank you.

I recently have been trying to find out why my email won't go online. A window pops up stating The identity of "pop.qwestoffice.net" cannot be verified. The certificate for this server is invalid. You may be connecting to a server that is pretending to be "pop.qwestoffice.net" putting information at risk. It asks to connect anyway? Anyone out there have a clue? I am losing my contacts with my clients.

Java WebDynpro's and IE security settings for file download

We have a EP 7.0 SP13 environment on which we have deployed a number of own developed java webdynpro's. In some of these webdynpro's we provide the file download functionality. The portal and webdynpro's are used by both internal personnel and external customers.
On the other hand the default Internet security settings for Internet Explorer, disable "Automatic prompting for file downloads".
When a user, with these default security settings active, tries to use our webdynpro's file download functionality, the screen seems to refreshes but no file download starts. When (s)he retries, the session runs for some minutes and gives following error message:
"com.sap.tc.webdynpro.services.session.LockException: Thread SAPEngine_Application_Thread[impl:3]_20 failed to acquire exclusive lock on client session ClientSession".
This behavior is explained in SAPNote 1234847. Webdynpro provides a single-thread module, meaning a user session is blocked for the during of the request. And because the previous file download isn't yet completed the new try can't start.
Issue now, although the users IE settings allow file downloads and don't block pop up's, he can't download the file and even isn't made aware of the cause of the failure.
How can we avoid this issue, without having to communicate the
application requires specific browser settings?

Welcome to the Apple Support Communities
See > http://support.apple.com/kb/HT5290
You can install the program using different ways:
1. Right-click the application installer and choose Open.
2. Go to System Preferences > Security and Privacy and select Anywhere in Allow applications downloaded from

Admin_client.jar 10.1.3.1.0 and changing JVM settings for OC4J in opmn.xml

Just now briefly looked at admin_client.jar 10.1.3.1.0. It appears that there is new functionality to create/alter and interrogate (J2EE) resources in this utility. This partially answers my other question, as stated in Jython support in Oracle Application Server 10g R3 (10.1.3)
(Would be nice to get a definitive answer on scripting though)
Anyway...
As a follow-up question. Will there also be functionality (or is there already functionality) which lets me change JVM settings of OC4J components as they are declared in the opmn.xml, using only command line (and/or scripting) tools?
Thanks

Jan -- there is no out of the box command line utility that can amend the JVM settings for an OC4J instance.
As Deepak alluded to, it is possible to do this using JMX because all the OPMN configuration elements are all reachable from JMX. This means you can create whatever Java JMX client you desire to modify the settings, or use a scripting environment which provides nice support for JMX (for example Groovy with its GroovyMBean) to access and use the OpmnConfig MBean set to change the OPMN configuration values.
Asanka -- the 10.1.3.1 release has lots of capability in ASC to manage the OPMN settings from a browser -- including modifying all the JVM settings (things like heap, System properties, etc.) as well as OC4J switches (-userThreads, etc.)
cheers
-steve-

Time Capsule - Can it run as DHCP router, create a wireless network and plug into switch for wired network all at the same time?

I have a closet with Wired connections from all over the house terminating in it. I also have the internet modem and a switch in this closet. My old setup was a netgear in the closet creating a wireless network and also feeding the Ethernet ports all over the house. In my room, I had an Airport express (a month old) bridging the wifi to make the wifi network larger. The Express was hard wired from the wall and my mac mini was using it's wifi (printer was plugged into other ethernet port). Everything was working great.
Fast forward to last week. My Netgear died. So, I bought a time capsule. My plan was to move the Express to the closet and have it create the wifi network and also then run cat 5 cord from express to the switch to feed all the wired wall plugs. Reset it and set it up to create the wifi network as well as DCHP NAT. Wireless was running great on it. Then I plugged in the Cat 5 in the second Ethernet Port to the switch. Wifi stopped working and none of the computers would connect using wired connections either. They would see a 'network' but nothing would work. I would unplug the Cat 5 feeding the swtich and the wireless would start working again. Plug the Cat 5 back in and wireless would stop.
So I thought I would try the Time Capsule in the closet and see if I could get it to work. Pretty much the same thing, except at this point I figured out if I went in and told it NOT to create a wifi network the wired portion worked fine and all the wired computers in the house worked fine. Of course, then I didn't have Wifi.
I'm not clueless when it comes to networking, but I can NOT figure this out! Can either the Time Capsule or Express Create the wifi network AND also feed the data to the switch for all the wired computers?
To simplify this is what I want my end result to be. I prefer the Time Capsule to be the wireless connection extender, but if I have to have the Express do it, I'm fine with that.
1. Express in the closet creating the wifi network as well as feeding the data to the wired connections via my switch.
2. have the Time capsule in my room at the opposite end of the house plugged into the hard wired connection to extend the wrieless network as well as have wired connections such as my printer and my Mac Mini.
If I can get #1 to work, I don't think I'll have any problems with #2. Help!

I have an equally complex setup with a managed switch actually but I have never seen the TC have this kind of issue.
What I do notice is you have changed the TC from defaults.. you are using a non-default IP range.
I have run across issues like this where people move things from default.
I would like you to start over.. factory reset the TC. That will set it back to default router mode.
Do the min setup on the TC..
1. Change all names from what you were using. That includes the TC name and wireless name/s
Make them short, no spaces and pure alphanumeric because that is the correct way to network. Apple default names with spaces and apostrophes are fundamentally bad.
2. With just the TC plugged into the switch.. and a single computer connected by ethernet. Power cycle the whole network.. this allows the switch to clear all the old MAC address.
3. Test on the computer just ethernet. Turn the wireless off.
The computer must use dhcp and must get an ip from the TC.
It has to get the correct Router.. ie Gateway.. I wish apple could stick with proper network terminology.
And it must get same address or valid DNS server address/es.
If it fails.. please plug ethernet directly to the TC.. bypassing the switch.
You should get the standard IP addressing and internet connection.
If not please post the screenshot from the Mac of the network preferences showing the ethernet setup.
I need to see what address it does get. I need you to make sure the ethernet is the TOP of the list. So rearrange the order of network connection. With the airport off it should just go to the top of the list.
If it appears to be working .. but a browser cannot connect, open a terminal and ping an internet address.
Ping the actual gateway address the ISP gives you and ping the ISP dns address.

"Error Reading Settings" for my Airport Extreme

When I installed Server everything worked fine.....until I exposed sevices in Airport using the Server Admin App. I did everything it asked ie. passwords etc., now when I open the Server app I get an error msg saying "An error occurred on the server while processing a command. type 'getIGDPortmaps' in plug-in 'servermgr_network'. "
I went into Airport Utility and everything seemed to be working correctly. Port mapping was checked and the services were mapped. The setup I have is 1 Airport Extreme connected to Server by ethernet with Tunneling enabled through internet options. Then I have 2 Airport Express' extending the network and those are set to "Local link only".
My question is....could I have double Port Mapping happening somehow? and how do I fix it so everything is handled through Server Admin App?
Thanks for the help!

Weel i am sorry but i do not have a solution.
Yet i have a similar problem.
I mean my Upgrade went very well, but Server App asks me to type the password ofmy airport extreme, but all the times did not work.
Thus i decided to reset the airport extreme. All connections works great, but Server App needs the password. Once again i type it but there is an error, as if the password was uncorrect.
Now if i do not fix this issue i cannot use my server because i cannot connect to it.
Thanks for the help
Dona

Questions on cache and general RSRT settings for plancube

Hi,
we would like to:
1) set request status 1 in RSRT for our planqueries, in order to automatically refresh the query after executing a planfunction (problem we have now is that the results of a planfunction are not automatically updated in the query. Only when doing something else like executing other function, saving, check locks, ... the results are visible).
2) activate delta cache for our planqueries
we have read OSS note 1136163 on RSRT settings. It says:
Aggregation level "A" is implemented internally by the automatically created query "P/!!1P" (plan buffer query). This query acts like an InfoProvider. It reads the data of the database or provides the data from InfoProvider "P", it adds the data of the delta buffer "Dp" (or the delta buffer Dpi if P is a MultiProvider with several PartProviders Pi that can be planned) and transfers the data manager as data of the InfoProvider "A" of type "ALVL". The query "P/!!1P" can use aggregates and the cache; this is exactly like each normal query in "P". If "P" is a MultiProvider, it is useful to set PARTITIONMODE to "1".
              For the query "P/!!1P" that is created automatically for an aggregation level or for all aggregation levels using the InfoProvider P, we recommend the following setting:
              Read mode "H", request status "1", cache mode "1" or higher, delta cache "true" and SP grouping "1".
              Furthermore, the selection to use the structure element (KIDSEL) should be "true".
              The input-ready queries in "A" should not, and cannot, use a cache. The request status is irrelevant since queries in "A" are automatically set to current data. The delta buffer does not currently support hierarchy processing. Therefore, aggregation level "A" cannot completely support read mode "H". For input-ready queries at A:
              Read mode "X", request status "0", cache mode "0".
             The delta cache and SP grouping are not visible
Problems we have:
1) for query P/!!1P (PCA_AGQF/!!1PCA_AGQF in our example) does not allow changing the request status (greyed out). It now has value 0 instead of 1. It also does not allow to activate the delta cache flag. How to change this? In RSDIPROP we have set partitionmode to 1 for the multiprovider and activated the delta cache flag...
2) can we use the cache / delta cache principle for our planqueries? If so, how to ensure these settings remain activated in RSRT?
regards
Dries
regards
dries

Hi,
To change the cache settings for your cube.
Open the cube in RSA1 and click in 'Chance'.
- click in the 'Environment' menu;
- expand 'InfoProvider Properties'
- select the option 'Change'.
You will be able to set the cache mode for this provider.
I don't think it will be possible use cache for a multiprovider, it is
not possible.
Regards,
Amit

Recently I was working on my home Network and lost my Password for my Home wireless connection. After many attempts, I remembered the password and was able to get in. Now the MacBook Pro only works at home on a Hard wire connection. I have an additional 9

Recently I was working on my home Network and lost myPassword for my Home wireless connection. After many attempts, I remembered thepassword and was able to get in. Now the MacBook Pro only works at home on aHard wire connection. I have an additional 9 devices on the same network, allare functioning properly. The Air connection works fine at any other Networksout side the Home connection. I did a PRAM reset, deleted the Network profileand rebuilt in System Preferences. Still unable to connect wireless on Homenetwork. Any Ideas?

I seem to have fixed it by putting <div class="clearfloat"></div> after the navigation bar?

The latest version of Firefox has totally stuffed my computer. Nothing now works properly and all my settings for web pages have totally disappeared.

Latest version of Firefox has totally stuffed my computer. Nothing works properly and all settings for web pages have disappeared.

Make sure that you allow pages to choose their colors and that you haven't enabled High Contrast in the Accessibility settings.
*Tools > Options > Content : Fonts & Colors > Colors : [X] "Allow pages to choose their own colors, instead of my selections above"
*http://kb.mozillazine.org/Website_colors_are_wrong
*https://support.mozilla.org/kb/Websites+look+wrong

My desktop has 2 users. Apple TV can only access the library on one of them. The other is says it is unable to contact. Network and home sharing settings are identical. Thoughts?

Any ideas why I can only access the itunes library and photos of one of the two user accounts on my iMAC? Settings for each of the accounts is the same, as far as I can tell.
Appreciate any help.

If you are attempting to share to both at the same time, you can't.
Are you selecting the second AppleTV in home sharing options on the MBP. Are all devices signed in for Home Sharing with the same AppleID?
You will also find some additional things to check here: Troubleshooting Home Sharing

How do I connect Airport Extreme and Time Capsule to my new iMac so that AE is used for network and TC only used for Time Machine backup?

I didn't realize that Time Capsule will only support the print function of a wireless multifunction printer. So I want to use Extreme for my network to have full use of my printer and use TC as the Time machine backup only. How to I make the connections?

Thanks for your response and this is getting complicated but I just purchased a new iMac as well as the Airport TC. I've had the Airport Extreme for a year or so. The Airport Extreme worked perfectly with my old iMac wirelessly and I had all functions of my printer with no problems. I was expecting the same with the TC. But the instruction that came with TC say to connect the printer to the TC via USB...which I did. And the print function worked perfectly but nothing else. In researching I discovered that when wired that way the TC only supports the print function...not scan or fax or anything else. I tried going wireless since my AE worked perfectly via wireless but I got no printer functions at all that way. But I'm wondering also if I tried that during a time I was having other issues...I had to delete and re-add my printer which solved some other problems. I may try that again...and see if I can get all print functions with just the TC connected
As far as connecting both your AirPort Extreme and Time Capsule on your network, we're not clear on exactly how you want to do this. Will the AirPort Extreme connect to your modem using an Ethernet cable and the Time Capsule connect to the AirPort Extreme using an Ethernet cable?.......or......do you want the Time Capsule to connect to the network using wireless?
Well... first of all I would like not to have to use the AE at all...I would prefer using just my TC for network, all print functions and Time Machine backup if that's possible. My printer will not accept Ethernet connections (Canon MX512).
After failing at getting this to work, I decided I would try to use my AE for net and print functions and just use my TC for Time Machine backup. I tried several different connection configurations with no success until finally I connected cable modem to my AE via Ethernet and went wireless with the AE and printer. but connected the AE to the TC via Ethernet and amazingly everything worked like a charm (for a while) and I was patting myself on the back for being so smart. But now I find that the connection only lasts for a short time. If I leave it for a while the TC goes invisible...or at least I see a message saying the Ethernet is unplugged...but it is not... and I lose internet connection even though I have a green light on my AE. So now I'm at a loss. I don't know why I keep losing network signal and why my system thinks the Ethernet is unplugged.
So... after all this...I figured I wasn't so smart after all and I must have things wired incorrectly.
So... it sounds like you are saying I should go back and try again to get my new TC to work as I want it to via wireless instead of connecting via USB...is that correct? Could you tell me exactly how I should wire my equipment from cable modem to AE and/or TC to achieve net capability, full functions of my printer and Time Machine backup...
Thanks...

New network and modem - new settings for Extreme Airport?

Similar Messages

Maybe you are looking for