New Nf980-g65 board refuses to post please help

Hi everyone I just purchased a nf980-g65 board and installed the cpu a phenom II 945 and connected everything and the board will not post no beeps fans spin up and one power phase light comes on. If I removed the ram however the board will make 3 long beeps without the ram installed I did a bench test no change with ram installed the ram is patriot pdc32g1333elk is the ram causing an issue or what could be wrong?

Is this a new build?
Does it worked before?
Have you tried to boot with barabone setup and mainboard of PC case?
Do >>Clear CMOS Guide<< with power cord removed,
leave 1 memory stick in 1st DIMM close to CPU socket. Then try to boot.
Quote
Ram: patriot pdc32g1333elk 2x 1gb 1333mhz ddr 3
This is Intel's tested memory.. ==> http://static.compusa.com/pdf/Patriot-PDC32G1333ELK-datasheet.pdf
• Tested and compatible with Intel
P35, X38 and X48 chipsets

Similar Messages

New NF980-G65 with an AMD X6 1090T and the BIOS Update Utility Crashes?

Last week I received my new NF980-G65 board and with it an AMD Phenom II X6 1090T (Thuban 3.2GHz Socket AM3). After installing the board and starting it up for the first time I noticed that it reports BIOS version 1.1 and CPU unknown. Next I downloaded the BIOS update to version 1.3 from msi, made a boot USB stick and powered up again. System will not boot from USB. I tried now over 20 different sticks from 256MB to 64GB and none of them worked!
Went back to my old system and ripped its floppy drive out to install it in the new computer. Had to go to RadioShack since I have not touched a floppy in over 10 years, but they had some on clearance. Made me a boot disk, put the new BIOS and install utility on it, booted the system with the floppy, started the BIOS update utility and watched it crash. When I start it by itself it gives me three screens of options and commands, but as soon as I try to use one of the commands or update the BIOS it keeps crashing.
What do I have to do to get the BIOS on the NF980-G65 updated so it will run with my AMD X6 1090T processor?
Thank you in advance for ANY help...
Tyler

Quote
I am sorry, but I need to work with this thing since I make a living writing code, I do not play with it! This thing and the support I am getting for it are not worth my time or money!
What thing are you talking about? You are experiencing the a certain symptom for which you do not know the cause. For some strange reason and without any in-depth tests you seem to assume that the board must be the problem (ignoring all other components (for example your factory overclocked memory modules).
Quote
the support I am getting for it are not worth my time or money!
What support have you tried to get that actually has to do anything with money? Please note that this is not MSI Technical Support but a User-to-User forum, run by users (just like you) that do not get paid for donating their private time to try to help others. Whatever your level of frustration is in regards to the money spent for your components, please do not use it to insult anyone here in this forum.
Quote
The result remains the same, the update utility keeps crashing...
Are still using the same floppy drive with the same floppy disk in it?
What is your current BIOS-Version?
Quote
BIOS update utility
What version? What is the exact file name of that utility?
Quote
ade me a boot disk
How/Based on what DOS Version?

Hi, I am new to Mac and i managed to install and configure all the services. Now my issue is when i sending mail using the local server to internal, mail are not receiving. Mail queue showing Connection refused error. Please help me

I am new to Mac and i managed to install and configure all the services. Now my issue is when i sending mail using the local server to internal, mails are not receiving. Mail queue showing Connection refused error. Please help me
Thanks
GIRI

Try this -> http://support.apple.com/kb/TA38632?viewlocale=en_US

My iPhone 4S was replaced yesterday due to my handset being faulty. Before I gave the faulty one back I made sure all pictures were in photo stream! All 1006 were however when I got home and set up my new handset, there's only 146. Please help??

I received my new iPhone 4S today due to the last one being faulty. I had 1006 pictures in my photo stream however on setting my new phone up I only have 146 :( please help?

Had this problem before. sometimes it's the network. downloading all the photos take time.If you r so sure 1006 pics are in the photo stream, then no need to worry. It'll come. Give it time. Good things take time! <wink*>

HT1277 I cannot open the new email icon for 10.6.8 and the latest secrtoy update. My old "Stamp" icon email won't let me in either indicating that the new OS version doesn't work. Please help

I cannot open the new email icon for 10.6.8 including the latest security update. My old "Stamp" icon email won't let me in either indicating that the new OS version doesn't work. Please help. I have spend over 4 hours installing and reinstalling updates, etc. and I don't know where to go from here.....

Mac OS X v10.6: Mail.app won’t open, or "You can't use this version of Mail…" alert after installing Security Update 2012-004:
http://support.apple.com/kb/TS4424?viewlocale=en_US&locale=en_US
Fellow user Grant Bennet-Alder offers this solution:
Some users have reported this problem if the Mail Application has been moved out of the top-level /Applications folder, or duplicated in another location.
When the Security Update is done, the old version of Mail is disabled.
The solution has been to:
1) make certain Mail is in the /Applications folder
2) There is no other copy anywhere else.
3) Once steps 1 and 2 have been done, Manually download and re-apply the Security Update (2012-004) by hand.
Security Update 2012-004 (Snow Leopard)
If the Mail.app has been LOST, it can be re-installed by applying the 10.6.8 version 1.1 combo update. But this update is quite large and it is usually not necessary:
Mac OS X 10.6.8 Update Combo v1.1

Hello, I have a big batterylife problem with my brand new iPod touch 4Gen 8GB white. Please help...

Hello, I have a big batterylife problem with my brand new iPod touch 4Gen 8GB white. Please help?

What battery life are you getting? Is it short when you are using the iPod? When it is sleeping?

Brand new nf980-g65 no post after bios update

I just built a system using an NF980-G65 with a Phenom II x4 and after updating the bios it has no post.
I am not sure how to proceed. I tried removing all accessories and removing the battery but nothing helped.

What bios did you flash and did flash end successfully or was it interrupted.

C7180 printer refusing NEW yellow ink, message freezing screen. Please help!

Have Photosmart C7180 All-in-One. Have replaced yellow ink twice, (returning to store thinking the lot was bad), but the machine won't accept it. At the same time I replaced two other colors with no problem. This is just in the yellow. Message shown is - "The following ink cartridge appears to be missing or damaged." I know it is not missing and don't believe it is damaged because of the two changes. This message has frozen my screen and I can't copy, print, fax or anything. I am desperate to get this problem fixed as I need the machine for business. I put the just about empty cartridge back in to print something quickly and it worked but that cartridge is empty now. I do have the correct replacement ink cartridge. Please help! Thank you.

Hi
I'm having the same problem with my L7680 I've been looking through this form and it seems there are a lot of people with similar all in ones having the same problem cleanig, new ink twice resets etc don't seem to help.

Brand new macbook- cant connect to internet. Please help!

Hi everyone, brand new macbook. i connected the ethernet and its giving me all these problems and will not connect to the internet. I tried to just let it configure automatically but even that doesnt work.
I have ethernet via time warner cable btw.
please help!
thank u!

Here is how to do a power cycle or what is called a reset.
Plug in your mac to your modem
Un plug the power cord to your modem
Wait 5 seconds, then plug the power cord back in
Give a minute or so to reboot and re-config its settings
Try clicking on safari and connecting to the internet
This should work, if not use the mac internet connect wizard to try and fix the problem.
If both of those solutions do not work then post back here.

How to Open a New window from a List region Link, Please help

I am trying to get a new full window( Not popup window) open from a list region link. The list region entry is an Image. I get the new page open, but it is not in new window, it is in the same window.
I know I have to give the target = "_blank" somewhere. But In List region, I dont know where to add this.
Please help
George

Yes, you are right Arun. That is more elegant way of
doing it. Keep it up. thankx..
Btw, why do you hate javascripts? Can you imagine the
internet world without javascript (or ant scripting
language)?yep i agree... but i try my best to avoid scripts.. as i had been workin around some japanese technologies... and there are three major mobile market players there... who has their own content type and all those devices never support javascript..
more over i donno that... in all 3 yrs i have never used that ;-))

My updates are failing. Adobe application manager may be damaged. I have downloaded and installed a new copy and the problem persists.   Please help.

I am trying to update Photoshop CS6 in order to read my camera's RAW files. It is a camera that is supported by Adobe Photoshop CS6. However, when I try to get the Adobe Application Manager to update the software, it fails to do so. (The spinning wheel tells me it is checking for updates and then quits, saying that "Update Failed - Updates could not be applied. Adobe Application Manager may be damaged. Download and install a new copy of Adobe Application Manager.")
I have tried to reinstall the Adobe Application Manager 8.0, which gives me the following error message "We've encountered the following issues. Installer failed to initialize. Please download Adobe Support Advisor to detect the problem." However, when I go to the link provided to download the Adobe Support Advisor, this piece of software NO LONGER EXISTS. "
The Adobe Support Advisor has been discontinued
The Adobe Support Advisor tool was used to analyze installer log and system information associated with installation errors. The tool has been replaced with improved installation support mechanisms. Please visit Adobe Support section for Knowledge base articles around Installation."
So, I have gone to the forums and took the recommended step to update my software manually - getting the update Photoshop_CS6_13_0_6upd-2.dmg. However, this update also fails stating that my Adobe Application Manager may be damages. Download and install a new copy of Adobe Application Manager. Which puts me right back where I started.
I have also taken the step of completely reinstalling Photoshop CS6. This did not solve the problems outlined above.
Please help!

reset your preferences:
dreamweaver: http://helpx.adobe.com/dreamweaver/kb/restore-preferences-dreamweaver-cs4-cs5.html
flash: http://helpx.adobe.com/flash/kb/re-create-preferences-flash-professional.html
indesign: https://forums.adobe.com/thread/526990
lightroom: http://www.lightroomforums.net/showthread.php?14226-Resetting-%28or-Trashing-%29-the-Light room-Preferences-file
photoshop: https://forums.adobe.com/thread/375776
if that fails, uninstall ps, clean (Use the CC Cleaner Tool to solve installation problems | CC, CS3-CS6) and reinstall. then use the manual updates.

My iPod nano g7 isn't showing up on iTunes although i plug it in. it shows on the computer but not on iTunes. also it won't sync , accept new songs and doesn't put on podcasts. it is new, i got it for christmas. PLEASE HELP

my iPod nano g7 isn't showing up on iTunes although i plug it in. it shows on the computer but not on iTunes. also it won't sync , accept new songs and doesn't put on podcasts. it is new, i got it for christmas. PLEASE HELP

Hi avmary11,
If your are having issues with your iPod not being recognized by iTunes (but it is being recognized by the computer), you may find the following article helpful:
iPod: Appears in Windows but not in iTunes
http://support.apple.com/kb/ts1363
Regards,
- Brenden

HT4623 I changed my itunes email but my iphone is still my old email, and it prompts me to enter password but it doesnt work. How can I get my new itunes email on my iphone4? Please help.

I changed my itunes email the other day. I need to know how to change my email on my iphone 4 so I can install apps and stuff. How do I change my itunes email on my phone to the same as my computer. Please help bc it prompts me to enter my password but it is my old email and now it wont work. What do I do?

Hi Friend,
Go to: Settings>>iTunes Store and App Store, click in your old email and finalize the section. Here, sign in your new email with new password.

How do I change my apple id from an old one that does not exist anymore to the new one I use....Please help me I can't update any downloads for my apps.

How do I change my apple ID from an old one that doesnot exist anymore to a new old? When I purchased my macbook I had a mac.com email address but now have a me.com one. My computer is linked to the mac one. I cant update my apps....some one please help.

Well when I first purchased I had an mac address, which I have not used for a long time I started a me address about 18months ago. and up untill I updated my iPhone I have been able to use my mac.com now I cant and dont know what to do because it tells me to verify my apple ID. I put in the password etc and doesnot take me anywhere as I cant access the emails.

HOW TO - Create new from clipboard and process multiple files - please help

Need help - have new version of photoshop on trial only ATM...
Want to know - HOW TO:
1. Create new from clipbaord
2. Process multiple files
Please help.

For clipboard copy, I start with File > New and the size will be set to what's in the clipboard. Then once the new file is opened, Edit > Paste will place the clipboard contents as a layer in the new document.
You must remember to use the command Layer > Flatten Image of you want to save as jpeg or any other file format that doesn't support layers.
For processing multiple files,
File > Automate > Batch or
File > Scripts > Image Processor...
Check the User guide or google information for those commands if you have specific needs.
Gene

New Nf980-g65 board refuses to post please help

Similar Messages

Maybe you are looking for