New Portable HD not found - Please Help

Hi,
I just purchased an external portable hard drive that's supposed to be "plug and play" for both Mac & Windows OS but my Powerbook isn't even picking up the drive. When I insert the USB (after connecting the cable to the drive, per the instructions) nothing happens at all. I then tried it on my desktop running XP and it found the drive with no problems, installed the included drivers & back up software & it's ready to go.
I've seen in other threads here that Disk Utility or the "Finder" could show the drive even if it doesn't auto-mount to the desk top, but when I go to the finder, nothing there (Unless I'm looking in the wrong place?) and in Disk Utility, I see my PB hard drive but that's it. Here's what I've done so far:
-Tested on different system/OS & external HD works fine
-Tried external HD on both USB ports and neither recognize drive to mount (HD light does power on, however)
-Tested my USB ports on PB with flash drive (Cruzer 4GB)& this drive comes up perfectly as usual; as does my iPod and a laptop fan works as well.
The external HD is a Toshiba 320GB HDDR320E03X.
I'm running a Powerbook G4 1.25 Ghz w/ 10.3.9
If anyone has any ideas how I can get this drive to show up and/or reformat it for the Mac (I'm ok w/ not using it for the desktop now), I'd appreciate it.

Hi, Rolo. If your drive is spinning up, lighting up, making normal noises, etc., but not mounting on the desktop, your Powerbook doesn't supply enough USB bus power for your hard drive. This is a very common Powerbook problem for which there is no direct remedy. You will have to provide power to the drive from another source: a) an AC-powered USB hub; b) an AC adapter connected directly to the drive, if the drive has an input port for one, c) a USB 2 CardBus adapter that comes with its own AC adapter, or d) a "Y" cable such as this one that allows your drive to draw power from both of your Powerbook's USB ports instead of just one.

Similar Messages

New Hard drive not working - please help!!!

This is an original thread that I'd started:
http://discussions.apple.com/thread.jspa?threadID=2066043&tstart=0
Since that, I tried the following this morning.
I took out the old 100GB drive and fitted the new 500GB (blank) drive. My plan was to fresh install OSX, install Carbon Copy Cloner and then clone the old drive by plugging it in with a reading device I have. What actually happened was the following:
I put in my Mac OSX install disc 1. I opened disc utility from the top toolbar. In disc utility the new drive showed up and I formatted (erase option) it to mac OS Extended (journalled). I then began a fresh install of OSX. As it started the macbook told me I was '+running on battery power+' and '+was I sure?+'. With full battery I said yes and continued. All was going well and it prompted for the second install disc. It got some way through that and then got stuck at 38% installing garage band loops. The new internal drive was also making a repetitive noise - not loud or anything but certainly sounded like it was searching for something. As the whole thing was stuck and nothing was working I held down the power button.
I tried again with the first disc but it wont even do anything anymore! I took out the new drive and put in the old one. Booted up. Connected the new drive to the reader with the idea of re-formatting it via disc utility.
But now the brand new drive is not readable and is making the a few funny repetitive noises.
Please help me someone - I'm very worried about this new drive now!!! Is is broken or corrupted or something???
Your help is very much appreciated
Adam

Vegas Superstar wrote:
My plan was to fresh install OSX, install Carbon Copy Cloner and then clone the old drive by plugging it in with a reading device I have.
Hi VS,
What "reading device" are you using?
As it started the macbook told me I was '+running on battery power+' and '+was I sure?+'. With full battery I said yes and continued.
It is best to have the power adapter connected when running a long process like this which cannot be interrupted.
The new internal drive was also making a repetitive noise - not loud or anything but certainly sounded like it was searching for something. As the whole thing was stuck and nothing was working I held down the power button.
How long was it "stuck?"
I tried again with the first disc but it wont even do anything anymore! I took out the new drive and put in the old one. Booted up. Connected the new drive to the reader with the idea of re-formatting it via disc utility.
But now the brand new drive is not readable and is making the a few funny repetitive noises.
Please help me someone - I'm very worried about this new drive now!!! Is is broken or corrupted or something???
It sounds like there is something amiss with the new HD. If you have access to a different external enclosure, (even on a PC, just to see if the HD will function), you could try erasing/formatting it again. If not, I think it's time to contact the vendor about a return.

Original files not found, please help.

I am running iTunes 8.0.1.11, and I have about 11.5 gigs or so of music. Today I fired up iTunes and started skimming through songs like I often do, only to start playing a song and have the "original file not found" message pop up. I took a deeper look, and the majority of my 3200 songs show this message. There is no common factor between these songs, some are from the iTunes Store, some are from CD's, and some are from various mp3 services. In some cases, a few of the songs from a CD are missing, while others are present. Under "iTunes Music" in "My Music", the music folders (ie "Linkin Park") are present, but it appears that all the music has been deleted from in them.
I am a little miffed at this, because I had quite a few rare albums and EPs in my collection, and none of them were backed up.
Is there any way to get them back? Perhaps the file paths were changed? I hope that the music is still on the HD somewhere, and that I don't have to hunt down all these albums again. Any help would be great.

Sadly, I've been looking around for around an hour for an answer to this problem, yet to just waste time.
I have the same problem and can't find an obvious way to fix it. Nothing works without asking me to locate the file in my music folders. On my iPhone I have roughly 35-40 artists listed, on iTunes I have 9 that are listed in the music folder, only about 15 of my 349 songs work. Sadly, I can't update my iPhone until this is fixed, thank goodness for the wall charger! I've noticed that it made the songs that were "Un-checked" go missing and the "Checked" songs are perfectly fine!
This problem has been around for ages, this happened to me like a year ago on a different version of iTunes. Yet, I haven't seen APPLE mention anything about it, at least acknowledge it! If I find an answer I won't waste anytime and will post it immediately, but as for now APPLE <insert phrase>(I'm going to use the phrase 'is lazy')!
Message was edited by: King21092
Also I would like to add that it seems like my songs have disappeared from my HDD, amazingly! That or they have been moved somewhere else. I originally had the songs on my old dell, copied the songs to my new HDD for my new PC. Then that HDD went bad, so I moved it to my other HDD, so I have back-ups.

NEW IPOD NANO NOT WORKING, PLEASE HELP

Hi Guys,
I have the large IPOD (4 YEARS OLD) and bought a 2nd Ipod Nano that's smaller for the gym. I plugged it into my MAC BOOK PRO and it keeps saying it needs to be updated which I press "OK" and then it asks for my password and when I type it in, it keeps stating it's "incorrect"? What should I do, any help would be greatly appreciated!
Thanks

Vegas Superstar wrote:
My plan was to fresh install OSX, install Carbon Copy Cloner and then clone the old drive by plugging it in with a reading device I have.
Hi VS,
What "reading device" are you using?
As it started the macbook told me I was '+running on battery power+' and '+was I sure?+'. With full battery I said yes and continued.
It is best to have the power adapter connected when running a long process like this which cannot be interrupted.
The new internal drive was also making a repetitive noise - not loud or anything but certainly sounded like it was searching for something. As the whole thing was stuck and nothing was working I held down the power button.
How long was it "stuck?"
I tried again with the first disc but it wont even do anything anymore! I took out the new drive and put in the old one. Booted up. Connected the new drive to the reader with the idea of re-formatting it via disc utility.
But now the brand new drive is not readable and is making the a few funny repetitive noises.
Please help me someone - I'm very worried about this new drive now!!! Is is broken or corrupted or something???
It sounds like there is something amiss with the new HD. If you have access to a different external enclosure, (even on a PC, just to see if the HD will function), you could try erasing/formatting it again. If not, I think it's time to contact the vendor about a return.

SAXParser type declaration not found - PLEASE HELP!!

I am using XML to parse an incoming string of XML. I want to use an SAXParser to do this, but I cannot create an object of this type. I have the jar file jaxp.jar, xalan.jar, and crimson.jar in my classpath.
Is there anything else that I need to do in order to get the parser to work.
This is a very urgent need so any help is appreciated. Here is the error:
Class SAXParser not found in type declaration;

I have figured out the issue. Thanks for the help. I do have one more issue though. I am trying to parse a string of xml data and I need to pass my parse() method an InputSource object that I guess I will make from my incoming String.
Any thoughts on how to do this?

Class not found********please help!

I'm trying to run my jsp application which imports two classes that i have saved in ROOT/WEB-INF/classes/business and ROOT/WEB-INF/classes/data. when I run the application by entering the url on the browser i get the following error. Does this mean the server cannot locate these two classes and what should i do to resolve this problem?
type Exception report
message Internal Server Error
description The server encountered an internal error (Internal Server Error) that prevented it from fulfilling this request.
exception
org.apache.jasper.JasperException: Unable to compile class for JSP
/opt/jakarta/tomcat/work/localhost/_/replace$jsp.java:3: Package business not found in import.
import business.*;
^
/opt/jakarta/tomcat/work/localhost/_/replace$jsp.java:4: Package data not found in import.
import data.*;
^
2 errors
at org.apache.jasper.compiler.Compiler.compile(Compiler.java:284)
at org.apache.jasper.servlet.JspServlet.loadJSP(JspServlet.java:546)
at org.apache.jasper.servlet.JspServlet$JspServletWrapper.loadIfNecessary(JspServlet.java:177)
at org.apache.jasper.servlet.JspServlet$JspServletWrapper.service(JspServlet.java:189)
at org.apache.jasper.servlet.JspServlet.serviceJspFile(JspServlet.java:382)
at org.apache.jasper.servlet.JspServlet.service(JspServlet.java:474)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:247)
at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:193)
at org.apache.catalina.core.StandardWrapperValve.invoke(StandardWrapperValve.java:243)
at org.apache.catalina.core.StandardPipeline.invokeNext(StandardPipeline.java:566)
at org.apache.catalina.core.StandardPipeline.invoke(StandardPipeline.java:472)
at org.apache.catalina.core.ContainerBase.invoke(ContainerBase.java:943)
at org.apache.catalina.core.StandardContextValve.invoke(StandardContextValve.java:201)
at org.apache.catalina.core.StandardPipeline.invokeNext(StandardPipeline.java:566)
at org.apache.catalina.core.StandardPipeline.invoke(StandardPipeline.java:472)
at org.apache.catalina.core.ContainerBase.invoke(ContainerBase.java:943)
at org.apache.catalina.core.StandardContext.invoke(StandardContext.java:2344)
at org.apache.catalina.core.StandardHostValve.invoke(StandardHostValve.java:164)
at org.apache.catalina.core.StandardPipeline.invokeNext(StandardPipeline.java:566)
at org.apache.catalina.valves.ErrorDispatcherValve.invoke(ErrorDispatcherValve.java:170)
at org.apache.catalina.core.StandardPipeline.invokeNext(StandardPipeline.java:564)
at org.apache.catalina.valves.ErrorReportValve.invoke(ErrorReportValve.java:170)
at org.apache.catalina.core.StandardPipeline.invokeNext(StandardPipeline.java:564)
at org.apache.catalina.valves.AccessLogValve.invoke(AccessLogValve.java:462)
at org.apache.catalina.core.StandardPipeline.invokeNext(StandardPipeline.java:564)
at org.apache.catalina.core.StandardPipeline.invoke(StandardPipeline.java:472)
at org.apache.catalina.core.ContainerBase.invoke(ContainerBase.java:943)
at org.apache.catalina.core.StandardEngineValve.invoke(StandardEngineValve.java:163)
at org.apache.catalina.core.StandardPipeline.invokeNext(StandardPipeline.java:566)
at org.apache.catalina.core.StandardPipeline.invoke(StandardPipeline.java:472)
at org.apache.catalina.core.ContainerBase.invoke(ContainerBase.java:943)
at org.apache.catalina.connector.http.HttpProcessor.process(HttpProcessor.java:1011)
at org.apache.catalina.connector.http.HttpProcessor.run(HttpProcessor.java:1106)
at java.lang.Thread.run(Thread.java:479)

Sorry for taking long to reply but here is the code for both packages. The main aim is to write information captuired from a form into a file.
Package business
package business;
public class User{
private String Msisdn;
private String Nimsi;
public User(){}
public User(String msisdn, String nimsi){
Msisdn = msisdn;
Nimsi = nimsi;
public void setmsisdn(String m){
Msisdn = m;
public String getmsisdn() { return Msisdn; }
public void setnimsi(String n){
Nimsi = n;
public String getnimsi(){ return Nimsi; }
package data;
import java.io.*;
import business.*;
public class UserIO{
public synchronized static void addRecord(User user, String filename)
throws IOException{
PrintWriter out = new PrintWriter(
new FileWriter(filename, true));
out.println(user.getmsisdn()+ "|"
+ user.getnimsi());
out.close();
}

I download itunes it says its successfully installed. then when i try to open it it says "apple application support not found" PLEASE HELP!!

I download itunes it says its successfully installed but then when i try to open it is says "Apple Application Support not found"

Let's try a standalone Apple Application Support install. It still might not install, but fingers crossed any error messages will give us a better idea of the underlying cause of the issue.
Download and save a copy of the iTunesSetup.exe (or iTunes64setup.exe) installer file to your hard drive:
http://www.apple.com/itunes/download/
Download and install the free trial version of WinRAR:
http://www.rarlab.com/
Right-click the iTunesSetup.exe (or iTunes64Setup.exe), and select "Extract to iTunesSetup" (or "Extract to iTunes64Setup"). WinRAR will expand the contents of the file into a folder called "iTunesSetup" (or "iTunes64Setup").
Go into the folder and doubleclick the AppleApplicationSupport.msi to do a standalone AAS install.
Does it install properly for you? If so, does iTunes launch properly now?
If instead you get an error message during the install, let us know what it says. (Precise text, please.)

Trouble downloading itunes 64 bit. when i click the link it says webpage not found. please help!

Having trouble downloading itunes 64 bit on windows 7. When i click download it brings me to a "webpage not available" page. Please help!

The servers are likely overloaded. Try again in a few hours.

'Integration Class not found' - Please help

Hi Guys
My EM from browser stopped working unexpectedly.
What happens is when I start login in, I can't move over login screen, no error messages displayed on browser screen. I use IE.
Here is what I find in emoms.log:
1510 2006-10-30 14:42:32,062 [Orion Launcher] ERROR app.Co
ntextInitializer contextInitialized.256 - Integration Class n
ot found: oracle.sysman.ocs.mntr.target.OcsOvfIntegration
1511 2006-10-30 14:42:32,062 [Orion Launcher] ERROR app.Co
ntextInitializer contextInitialized.256 - Integration Class n
ot found: oracle.sysman.ocs.mntr.target.OcsWebconfIntegration
1512 2006-10-30 14:42:32,078 [Orion Launcher] ERROR app.Co
ntextInitializer contextInitialized.256 - Integration Class n
ot found: oracle.sysman.ocs.mntr.target.OcsWirelessIntg
1513 2006-10-30 14:42:32,078 [Orion Launcher] ERROR app.Co
ntextInitializer contextInitialized.256 - Integration Class n
ot found: oracle.sysman.ocs.mntr.target.OcsCalGrpIntegration
1514 2006-10-30 14:44:23,015 [HttpRequestHandler-6627600]
ERROR sec.auth doLogon.207 - Error logging on:
1515 java.lang.NumberFormatException: multiple points
1516 at java.lang.FloatingDecimal.readJavaFormatString(F
loatingDecimal.java:1067)
I tried to recompile package as it say in:
http://forums.oracle.com/forums/thread.jspa?threadID=337544&tstart=0&messageID=1356947#1356947
but only received message back:
ORA-04043: object MGMT_AUDIT_LOG does not exist
Is there anyway for me to fix this problem without database re-installation?
Thank you, Gene.

Hi guys
Thank you for your support.
Here is an answer on your question Ugonic.
( I use mks tools ksh port for windows 2k)
Here is an output: ls C:/oracle/10/Db_1/opmn/bin
ons.exe onsclient.dll
C:/oracle/10/Db_1/opmn/bin> ./ons -help
Usage: .\ons [-d]
-d Daemon mode: forks and detached OPMN server process
-a <admin command> Please type ".\ons -a" for usage
I guess ons is a replacement of opmnctl on version 10.
I could not find opmnctl on my SUSE installation neither.
Now, I tried to experiment with em by using different URLs:
http://127.0.0.1:5501/em this is a loopback ip
http://10.104.3.79:5501/em this is my current ip
http://n513gg0_d1:5501/em this is my pc name
on
netscape 8.1.2 ( by the way problem started when i - stupid me - upgraded it from 8.1 to 8.1.2)
ie 6.0.280
On netscape: all 3 commands do not work.
ie: first two commands work and display all em functionality and the last one which uses my pc name - does not.
I did not mention to you that my pc uses dhcp and from what I read em DOES NOT like it. It likes permanent address.
I beleive I came accross of 2 problems:
1. netscape 8.1.2 is an uncompatible browser for em application.
2. name resolution does not work well with em. The proof for the last is error when I use http://n513gg0_d1:5501/em on ie, it does not trunslate it to ip address.
I also went to page: http://n513gg0_d1:5501 and displayed page:
Oracle Application Server Containers for J2EE 10g (9.0.4.0.0)
At the end of it I found test examples for:
JSP
servlets
Each group provides multiple exampls. It's interesting that no netscape neither ie are not able to work with all JSP examples.
For now I will be working with ie for em and I beleive problem is solved - you should be progmatic because dhcp/em/browser compatibility is too much to worry as long as it works.
My only concern - and I only study oracle - that I view it as a major architectural flaw in Oracle 10 - this dependence on em windows interface.
One can say: "you can do the same from command prompt" But how many of us who is learning Oracle or who used to use an old ie will be able to use command interface efficently specially when you need to react fast?
And, if Oracle provides such a great tool and wants you to use it heavily, don't they have to provide a separate installation option for just a re-installation of em itself ?
I was about to scratch my test installation and re-install it again. Would it be an option in production environment?
Thank you guys for your help and I with best to you.
Gene.

Method not found Please help!!

import java.sql.Connection;
import java.sql.Statement;
import java.sql.DriverManager;
import java.sql.SQLException;
import java.sql.ResultSet;
import java.io.*;
public class SnappyDriver
          public int j = 0;
public int number[];
public void main(String [] arguments)throws IOException
          Connection connection = null;
Statement statement = null;
          ResultSet rs = null;
          BufferedReader input = new BufferedReader(new InputStreamReader(System.in));
          try
// Load the database drievrs. An ODBC: JDBC bridge
Class.forName("sun.jdbc.odbc.JdbcOdbcDriver");
System.out.println("Drivers loaded");
// Obtain connection to the database.
connection = DriverManager.getConnection("jdbc:odbc:Questions", "", "");
System.out.println("Connection established");
// Cerate statement to read and write to/from database.
statement = connection.createStatement();
System.out.println("Statement created");
               System.out.println(" ");
               for ( int i = 1; i < 11 ;i++)
                    int ran;
                    ran = ranCheck();
                    //int rnd = ((int) (Math.random ()*10)+1);
                    System.out.print (" " );
                    rs = statement.executeQuery("SELECT * FROM Questions WHERE [Index] = "+ran+" ");
                    rs.next();
                    //execute resultSet printout .
                    System.out.println(" ");
                    System.out.println(" ");
                    System.out.print ("Random no = " + ran );
                    System.out.print (" " );
                    System.out.println("QUESTION NO: " + rs.getString("Index"));
                    System.out.println("->->->-> : " + rs.getString("Questions"));
                    System.out.println("Answer A: " + rs.getString("A"));
                    System.out.println("Answer B: " + rs.getString("B"));
                    System.out.println("Answer C: " + rs.getString("C"));
                    rs.close();
                    System.out.print("Please enter your answer: ");
                    //char responce;// read in 1 byte
                    //char letter = (char) System.in.read();
                    String response = input.readLine();
// Close statement and conenction.
statement.close();
connection.close();
                    catch (ClassNotFoundException cnf)
                         System.out.println("Could not find class: " + cnf);
                    catch (SQLException sqle)
                         System.out.println("SQL problem: " + sqle);
          //The main does not rocognise thid method to produce random numbers
     public int ranCheck()
          // Random method
          while(j<10)
               int rnd = ((int) (Math.random ()*10)+1);
               for(int k=0;k<=j;k++)
                    if (number[k]== rnd)
                         j--;
                         number [j] = rnd;
                         j++;
                         return (rnd);

You still have some misplaced {'s and }'s in there. Look carefully trough your code, and find them. (No, I am not doing it for you. It's not a difficult job, but it's kind of boring :) )
If you always are careful with the indendation, this kind of error is easier it avoid and easier to detect.

MacBook Pro 13 Early 2011 Battery Degradation to Not Detected, User Replaced New Battery also Not Detected, Please Help!

I have a MBP early 2011 13 inch and do not have Apple Care. After I installed Mountain Lion I noticed the battery health was dropping pretty rapidly, with a service battery warning. I tried resetting the SMC and PRAM and even a clean install. I took it into an Apple store and they said I should have cycled it more, but I could still use it. The health dropped and dropped until a battery would not even be detected. Because Apple would not replace it for me for free and I didn't want to pay for them to do so, I bought my own battery. Once I replaced the battery with the new one, it still says there is no battery connected.
When I detach the battery and then attach it again, the battery indicator lights on the side show 4 dots. When I plugged in the MagSafe connector, the fifth light started blinking (I thought it was charging) and then it went back to all of them blinking indicating no battery detected. The computer also automatically turned on when I connected the MagSafe.
I have tired multiple times to reset PRAM and SMC even after installing the new battery to no avail. I can use the machine with the MagSafe connected, but as soon as the cord is unplugged or bumped, it goes into the emergency sleep mode.
Any thoughts on what might be ailing this not yet two year old machine? My first Mac lasted 7 years before any logic board fail so I hope that is not it. Anything I should try that I haven't yet? Any ideas on what this might cost me through Apple?
Thanks!

Why don't you look through this to insure you did everything correctly:
http://www.ifixit.com/Guide/Installing+MacBook+Pro+13-Inch+Unibody+Early+2011+Ba ttery+Replacement/5116/1
Also, where did you get this battery?

Build of DC fails libraries on classpath are not found - Please Help

HI Guys,
I am trying to build an ejb dc.
There are no errors showing up in NWDS but when doing an Development Component -> Build the Build fails with the errors here in the log - how can I make sure the libs are found at compiletime?????
DC Model check:
   All used DCs are available locally
   validating dependency to build plugin "sap.com/tc/bi/bp/ejbmodule"
   validating dependency to public part "default" of DC "sap.com/ejb20"
   validating dependency to public part "default" of DC "sap.com/jdbc20"
   validating dependency to public part "default" of DC "acdc.de/pinguin/service/dic"
   validating dependency to public part "default" of DC "sap.com/configuration"
   validating dependency to public part "default" of DC "sap.com/connector"
   validating dependency to public part "default" of DC "sap.com/mail"
   validating dependency to public part "compilation" of DC "acdc.de/pinguin/ext/lib"
   validating dependency to public part "default" of DC "sap.com/jms_provider"
   validating dependency to public part "default" of DC "sap.com/jmsconnector"
   validating dependency to public part "default" of DC "sap.com/jms"
   validating dependency to used DC "apotheker.com/cape/base/external/lib"
   validating dependency to used DC "apotheker.com/cape/base/utils"
   DC model check OK
Start build plugin:
   using build plugin: sap.com/tc/bi/bp/ejbmodule
   starting build plugin from : D:\usr\nwds\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\SAP_BUILDT\DCs\sap.com\tc\bi\bp\ejbmodule\_comp\gen\default\public\ejb\
Build Plugin 'EJBModulePlugin', Version 7.00 SP 3 (NW701_03_REL, built on 2008-12-17 16:25:56 CET, CL51263)
   development component: pinguin/service/ejb (acdc.de)
      software component: MyComponents (demo.sap.com)
                location: local
                    type: J2EE, subtype EJBModule
           build variant: default
         output location: C:\Documents and Settings\user\.dtc\LocalDevelopment\DCs\acdc.de\pinguin\service\ejb\_comp\gen\default
       generation folder: C:\Documents and Settings\user\.dtc\LocalDevelopment\t\F77C06E96830A119E56EFB0EDB243F25
       plugin start time: 2011-12-02 18:28:55 GMT+01:00 (CET)
                 Java VM: Java HotSpot(TM) Client VM, 1.4.2_12-b03 (Sun Microsystems Inc.)
General options:
convert *.xlf to *.properties: yes
include sources for debugging: yes
Checking path lengths for sources
Path length checks finished in 0.016 seconds
Preparing data context..
No public part descriptor found for component "ejb20" (vendor "sap.com"), public part "default", using legacy mode.
No public part descriptor found for component "jms_provider" (vendor "sap.com"), public part "default", using legacy mode.
No public part descriptor found for component "jmsconnector" (vendor "sap.com"), public part "default", using legacy mode.
No public part descriptor found for component "jms" (vendor "sap.com"), public part "default", using legacy mode.
No 'default' JDK defined, will use running VM.
Data context preparation finished in 0.094 seconds
Creating Ant build file..
Creating output file: C:\Documents and Settings\user\.dtc\LocalDevelopment\DCs\acdc.de\pinguin\service\ejb\_comp\gen\default\logs\build.xml
Using Java class:     com.sap.tc.buildplugin.BuildEJBModule
Build file creation finished in 0.046 seconds
Starting Ant..
Using build file:     C:\Documents and Settings\user\.dtc\LocalDevelopment\DCs\acdc.de\pinguin\service\ejb\_comp\gen\default\logs\build.xml
Using build target:   build
Using Ant version:    1.6.2
compile:
      [echo] Start SQLJ Pre-processing
      [sqlj] Using catalog:xml/file/C:\Documents and Settings\user\.dtc\LocalDevelopment\DCs\acdc.de\pinguin\service\dic\_comp\gen\default\public\default\lib\java\acdc.de~pinguin~service~dic~default.jar;D:\usr\nwds\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\SAP-JEE\DCs\sap.com\ejb20\_comp\gen\default\public\default\lib\java\ejb20.jar;D:\usr\nwds\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\SAP-JEE\DCs\sap.com\jms_provider\_comp\gen\default\public\default\lib\java\sapjms.jar;D:\usr\nwds\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\SAP-JEE\DCs\sap.com\jdbc20\_comp\gen\default\public\default\lib\java\jdbc.jar;D:\usr\nwds\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\SAP-JEE\DCs\sap.com\jms\_comp\gen\default\public\default\lib\java\jms.jar;D:\usr\nwds\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\Documents and Settings\user\.dtc\LocalDevelopment\DCs\acdc.de\pinguin\ext\lib\_comp\gen\default\public\compilation\lib\java\acdc.de~pinguin~ext~lib~compilation.jar;C:\Documents and Settings\user\.dtc\LocalDevelopment\DCs\acdc.de\pinguin\ext\lib\_comp\gen\default\public\compilation\lib\java\paygate-1.0.2.jar;D:\usr\nwds\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\SAP-JEE\DCs\sap.com\jmsconnector\_comp\gen\default\public\default\lib\java\jmsconnector.jar;D:\usr\nwds\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\SAP-JEE\DCs\sap.com\servlet\_comp\gen\default\public\default\lib\java\servlet.jar
      [sqlj] translation finished
      [sqlj] 0 warnings
      [sqlj] 0 errors
     [timer] SQLJ Pre-processing finished in 0.828 seconds
      [echo] Starting Java compiler
      [echo] Settings:
      [echo]         debug: on
      [echo]      optimize: off
      [echo]   deprecation: default
      [echo]       verbose: default
      [echo]      encoding: UTF8
      [echo]        source: default
      [echo]        target: default
      [echo] source paths:
      [echo]       C:\Documents and Settings\user\.dtc\LocalDevelopment\DCs\acdc.de\pinguin\service\ejb\_comp\ejbModule
      [echo]       C:\Documents and Settings\user\.dtc\LocalDevelopment\t\F77C06E96830A119E56EFB0EDB243F25\gen_sqlj
      [echo]    class path:
      [echo]       C:\Documents and Settings\user\.dtc\LocalDevelopment\DCs\acdc.de\pinguin\service\dic\_comp\gen\default\compilation\lib\java\paygate-1.0.2.jar
      [echo]       D:\usr\nwds\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\SAP-JEE\DCs\sap.com\jmsconnector\_comp\gen\default\public\default\lib\java\jmsconnector.jar
      [echo]       D:\usr\nwds\IDE\IDE70\eclipse\plugins\com.sap.tc.ap_2.0.0\comp\SAP-JEE\DCs\sap.com\servlet\_comp\gen\default\public\default\lib\java\servlet.jar
      [echo]    output dir: C:\Documents and Settings\user\.dtc\LocalDevelopment\t\F77C06E96830A119E56EFB0EDB243F25\classes
     [javac] Compiling 163 source files to C:\Documents and Settings\user\.dtc\LocalDevelopment\t\F77C06E96830A119E56EFB0EDB243F25\classes
     [javac] ERROR: C:\Documents and Settings\user\.dtc\LocalDevelopment\DCs\acdc.de\pinguin\service\ejb\_comp\ejbModule\de\acdc\pinguin\facade\acdcPinguin001CustomFacade.java:21: package com.hp.cape.persistence.exception does not exist
     [javac] ERROR: import com.hp.cape.persistence.exception.FinderException;
     [javac] ERROR:                                          ^
     [javac] ERROR: C:\Documents and Settings\user\.dtc\LocalDevelopment\DCs\acdc.de\pinguin\service\ejb\_comp\ejbModule\de\acdc\pinguin\facade\acdcPinguin001CustomFacade.java:22: package com.hp.cape.persistence.exception does not exist
     [javac] ERROR: import com.hp.cape.persistence.exception.PersistenceException;
     [javac] ERROR:                                          ^
     [javac] ERROR: C:\Documents and Settings\user\.dtc\LocalDevelopment\DCs\acdc.de\pinguin\service\ejb\_comp\ejbModule\de\acdc\pinguin\facade\acdcPinguin001CustomFacade.java:23: package com.hp.cape.persistence.exception does not exist
     [javac] ERROR: import com.hp.cape.persistence.exception.RemoteServerException;
     [javac] ERROR:                                          ^
     [javac] ERROR: C:\Documents and Settings\user\.dtc\LocalDevelopment\DCs\acdc.de\pinguin\service\ejb\_comp\ejbModule\de\acdc\pinguin\facade\acdcPinguin001CustomFacade.java:24: package com.hp.cape.persistence.filter does not exist
     [javac] ERROR: import com.hp.cape.persistence.filter.FilterCondition;
     [javac] ERROR:                                       ^
     [javac] ERROR: C:\Documents and Settings\user\.dtc\LocalDevelopment\DCs\acdc.de\pinguin\service\ejb\_comp\ejbModule\de\acdc\pinguin\facade\acdcPinguin001CustomFacade.java:96: cannot resolve symbol
     [javac] ERROR: symbol : class RemoteServerException
     [javac] ERROR: location: class de.acdc.pinguin.facade.acdcPinguin001CustomFacade
     [javac] ERROR:   protected Object getHomeStub() throws RemoteServerException
     [javac] ERROR:                                         ^
     [javac] ERROR: C:\Documents and Settings\user\.dtc\LocalDevelopment\DCs\acdc.de\pinguin\service\ejb\_comp\ejbModule
     [javac] ERROR: symbol : class RemoteServerException
     [javac] ERROR: location: class de.acdc.pinguin.facade.acdcPinguin001Facade
     [javac] ERROR:   protected acdcPinguin001SB getacdcPinguin001SB() throws RemoteServerException
     [javac] ERROR:                                                   ^
     [javac] ERROR: C:\Documents and Settings\user\.dtc\LocalDevelopment\DCs\acdc.de\pinguin\service\ejb\_comp\ejbModule\de\acdc\pinguin\facade\acdcPinguin001Facade.java:192: cannot resolve symbol
     [javac] ERROR: symbol : class FinderException
     [javac] ERROR: location: class de.acdc.pinguin.facade.acdcPinguin001Facade
     [javac] ERROR:   public acdcPinguin001DTO findByPrimaryKey(BigDecimal id) throws FinderException, PersistenceException
     [javac] ERROR:                                                               ^
     [javac] ERROR: C:\Documents and Settings\user\.dtc\LocalDevelopment\DCs\acdc.de\pinguin\service\ejb\_comp\ejbModule\de\acdc\pinguin\facade\acdcPinguin001Facade.java:192: cannot resolve symbol
     [javac] ERROR: symbol : class PersistenceException
     [javac] ERROR: location: class de.acdc.pinguin.facade.acdcPinguin001Facade
     [javac] ERROR:   public acdcPinguin001DTO findByPrimaryKey(BigDecimal id) throws FinderException, PersistenceException
     [javac] ERROR:                                                                                ^
     [javac] ERROR: C:\Documents and Settings\user\.dtc\LocalDevelopment\DCs\acdc.de\pinguin\service\ejb\_comp\ejbModule
     [javac] ERROR:                                                                                ^
     [javac] ERROR: C:\Documents and Settings\user\.dtc\LocalDevelopment\DCs\acdc.de\pinguin\service\ejb\_comp\ejbModulePersistenceException
     [javac] ERROR:                                                                                ^
     [javac] ERROR: C:\Documents and Settings\user\.dtc\LocalDevelopment\DCs\acdc.de\pinguin\service\ejb\_comp\ejbModule\de\acdc\pinguin\facade\acdcPinguin002Facade.java:389: cannot resolve symbol
     [javac] ERROR: symbol : class PersistenceException
     [javac] ERROR: location: class de.acdc.pinguin.facade.acdcPinguin002Facade
     [javac] ERROR:   public acdcPinguin002DTO update(acdcPinguin002DTO data) throws PersistenceException
     [javac] ERROR:                                                          ^
     [javac] WARNING: Note: Some input files use or override a deprecated API.
     [javac] WARNING: Note: Recompile with -deprecation for details.
     [javac] 100 errors
Error: C:\Documents and Settings\user\.dtc\LocalDevelopment\DCs\acdc.de\pinguin\service\ejb\_comp\gen\default\logs\build.xml:158: Compile failed; see the compiler error output for details.
     at org.apache.tools.ant.taskdefs.Javac.compile(Javac.java:938)
     at org.apache.tools.ant.taskdefs.Javac.execute(Javac.java:758)
     at org.apache.tools.ant.UnknownElement.execute(UnknownElement.java:275)
     at org.apache.tools.ant.Task.perform(Task.java:364)
     at org.apache.tools.ant.Target.execute(Target.java:341)
     at org.apache.tools.ant.Target.performTasks(Target.java:369)
     at org.apache.tools.ant.Project.executeTarget(Project.java:1214)
     at com.sap.tc.buildplugin.techdev.ant.util.AntRunner.run(AntRunner.java:116)
     at com.sap.tc.buildplugin.DefaultAntBuildAction.execute(DefaultAntBuildAction.java:58)
     at com.sap.tc.buildplugin.DefaultPlugin.handleBuildStepSequence(DefaultPlugin.java:196)
     at com.sap.tc.buildplugin.DefaultPlugin.performBuild(DefaultPlugin.java:168)
     at com.sap.tc.buildplugin.DefaultPluginV3Delegate$BuildRequestHandler.handle(DefaultPluginV3Delegate.java:66)
     at com.sap.tc.buildplugin.DefaultPluginV3Delegate.requestV3(DefaultPluginV3Delegate.java:48)
     at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
     at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
     at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
     at java.lang.reflect.Method.invoke(Method.java:324)
     at com.sap.tc.buildtool.v2.impl.PluginHandler2.maybeInvoke(PluginHandler2.java:350)
     at com.sap.tc.buildtool.v2.impl.PluginHandler2.request(PluginHandler2.java:99)
     at com.sap.tc.buildtool.v2.impl.PluginHandler2.build(PluginHandler2.java:73)
     at com.sap.tc.buildtool.PluginHandler2Wrapper.execute(PluginHandler2Wrapper.java:59)
     at com.sap.tc.devconf.impl.DCProxy.make(DCProxy.java:1750)
     at com.sap.tc.devconf.impl.DCProxy.make(DCProxy.java:6004)
     at com.sap.ide.eclipse.component.provider.actions.dcproject.BuildAction.buildDCsForDevConfig(BuildAction.java:307)
     at com.sap.ide.eclipse.component.provider.actions.dcproject.BuildAction.access$200(BuildAction.java:58)
     at com.sap.ide.eclipse.component.provider.actions.dcproject.BuildAction$1.run(BuildAction.java:212)
     at org.eclipse.jface.operation.ModalContext$ModalContextThread.run(ModalContext.java:101)
Ant runtime 1.265 seconds
Ant build finished with ERRORS
Compile failed; see the compiler error output for details.
Error: Build stopped due to an error: Compile failed; see the compiler error output for details.
Build plugin finished at 2011-12-02 18:28:56 GMT+01:00 (CET)
Total build plugin runtime: 1.562 seconds
Build finished with ERROR

Hi Saurabh Agarwal,
I have double checked this. removed and added the relevant libraries but no luck.
the build log says that it can not find
     [javac] ERROR: C:\Documents and Settings\admitsepedollhofer1\.dtc\LocalDevelopment\DCs\acdc\some\service\ejb\_comp\ejbModule\acdc\some\facade\AcDcSome001CustomFacade.java:21: package com.ap.cape.persistence.exception does not exist
     [javac] ERROR: import com.ap.cape.persistence.exception.FinderException;
Build Path looks like this:
<?xml version="1.0" encoding="UTF-8"?>
<classpath>
    <classpathentry kind="var" path="JRE_LIB" sourcepath="JRE_SRC"/>
    <classpathentry kind="src" path="ejbModule"/>
    <classpathentry kind="src" path="gen_sqlj"/>
    <classpathentry kind="src" path="/LocalDevelopmentcapebaseutilsap.com"/>
    <classpathentry kind="var" path="TSSAP_JAVAX_HOME/lib/ejb20.jar"/>
    <classpathentry kind="lib" path="D:/Projects/some/0/DCs/ap.com/cape/base/utils/_comp/gen/default/public/compilation/lib/java/ap.comcapebaseutilscompilation.jar"/>
    <classpathentry kind="var" path="SAP_LOGGING_LIB_HOME/lib/logging.jar"/>
    <classpathentry kind="var" path="SAP_SYSTEM_ADD_LIBS/comp/SAP-JEE/DCs/sap.com/com.sap.engine.client.lib/_comp/gen/default/public/default/lib/java/sapj2eeclient.jar"/>
    <classpathentry kind="src" path="/DV2_some_Dsomeservicedicacdc.de"/>
    <classpathentry kind="var" path="SAP_EXCEPTION_LIB_HOME/lib/exception.jar"/>
    <classpathentry kind="lib" path="/DV2_some_Dsomeextlibacdc.de/libraries/paygate-1.0.2.jar"/>
    <classpathentry kind="lib" path="/DV2_some_Dsomeextlibacdc.de/libraries/commonsNet.jar"/>
    <classpathentry kind="lib" path="/DV2_some_Dsomeextlibacdc.de/libraries/jakarta-oro-2.0.8.jar"/>
    <classpathentry kind="var" path="TSSAP_JAVAX_HOME/lib/jms.jar"/>
    <classpathentry kind="var" path="TSSAP_JAVAX_HOME/lib/mail.jar"/>
    <classpathentry kind="var" path="SQLJ_RUNTIME"/>
    <classpathentry kind="lib" path="D:/Projects/some/0/DCs/ap.com/cape/base/external/lib/_comp/gen/default/public/compilation/lib/java/CapeJ2eePersistence.jar"/>
    <classpathentry kind="lib" path="D:/Projects/some/0/DCs/ap.com/cape/base/external/lib/_comp/gen/default/public/compilation/lib/java/CapeUtilities.jar"/>
    <classpathentry kind="lib" path="D:/Projects/some/0/DCs/ap.com/cape/base/external/lib/_comp/gen/default/public/compilation/lib/java/Cape.jar"/>
    <classpathentry kind="output" path="bin"/>
</classpath>
How can I make sure that the libraries are included in the build process?

Every time I install itunes i get an error message that says apple application support not found. please help!e

Hi i hope someone can help

With the Error 2, let's try a standalone Apple Application Support install. It still might not install, but fingers crossed any error messages will give us a better idea of the underlying cause of the issue.
Download and save a copy of the iTunesSetup.exe (or iTunes64setup.exe) installer file to your hard drive:
http://www.apple.com/itunes/download/
Download and install the free trial version of WinRAR:
http://www.rarlab.com/download.htm
Right-click the iTunesSetup.exe (or iTunes64Setup.exe), and select "Extract to iTunesSetup" (or "Extract to iTunes64Setup"). WinRAR will expand the contents of the file into a folder called "iTunesSetup" (or "iTunes64Setup").
Go into the folder and doubleclick the AppleApplicationSupport.msi to do a standalone AAS install.
Does it install properly for you?
If instead you get an error message during the install, let us know what it says. (Precise text, please.)

BRAND New laptop, battery not charging, please help me

Hi, I received my macbook today, and the battery is not charging. When my battery was still charged, I could use my macbook. The led on the charger was green. When it got to 0%, the laptop continued to work. So, I removed the charger (brillant idea) and it stop. Now, I can't start my laptop, and the led is yellow. The battery can't charge more than one "square" (which I can see on the battery itself). When I try to boot, I get the starting white screen, but then it shut down.
What should I do?
Message was edited by: mguillemette

I forgot to tell...
I tried to remove the battery, push the power button for 5 sec, and then restart, but without success.
After 15 minutes of "charging" (while the laptop is off), the led turns from yellow to green.
Message was edited by: mguillemette

When i try to burn a disk, it says "disk software not found" PLEASE help.

(Build 9200)
ASUSTeK Computer Inc. K54C
iTunes 10.7.0.21
QuickTime not available
FairPlay 2.2.19
Apple Application Support 2.2.2
iPod Updater Library 10.0d2
CD Driver 2.2.3.0
CD Driver DLL 2.1.3.1
Apple Mobile Device 6.0.0.59
Apple Mobile Device Driver 1.62.0.0
Bonjour 3.0.0.10 (333.10)
Gracenote SDK 1.9.6.502
Gracenote MusicID 1.9.6.115
Gracenote Submit 1.9.6.143
Gracenote DSP 1.9.6.45
iTunes Serial Number 00EBAA5406830318
Current user is not an administrator.
The current local date and time is 2012-11-23 00:14:27.
iTunes is not running in safe mode.
WebKit accelerated compositing is enabled.
HDCP is supported.
Core Media is supported.
**** External Plug-ins Information ****
No external plug-ins installed.
iPodService 10.7.0.21 (x64) is currently running.
iTunesHelper 10.7.0.21 is currently running.
Apple Mobile Device service 3.3.0.0 is currently running.

Microsoft Windows XP Home Edition Service Pack 3 (Build 2600)
SAMSUNG ELECTRONICS CO., LTD. NC10/N110
iTunes 10.2.2.14
QuickTime 7.6.9
FairPlay 1.11.17
Apple Application Support 1.5.1
iPod Updater Library 10.0d2
CD Driver 2.2.0.1
CD Driver DLL 2.1.1.1
Apple Mobile Device 3.4.0.25
Apple Mobile Device Driver 1.55.0.0
Bonjour 2.0.5.0
Gracenote SDK 1.8.2.457
Gracenote MusicID 1.8.2.89
Gracenote Submit 1.8.2.123
Gracenote DSP 1.8.2.34
iTunes Serial Number 0012AC480ECAB098
Current user is an administrator.
The current local date and time is 2011-06-11 22:10:48.
iTunes is not running in safe mode.
WebKit accelerated compositing is enabled.
HDCP is not supported.
Core Media is not supported. (16005)
Video Display Information
Mobile Intel(R) 945 Express Chipset Family
Mobile Intel(R) 945 Express Chipset Family
**** External Plug-ins Information ****
No external plug-ins installed.
iPodService 10.2.2.14 is currently running.
iTunesHelper is currently not running.
Apple Mobile Device service 3.3.0.0 is currently not running.
**** CD/DVD Drive Tests ****
No drivers in LowerFilters.
UpperFilters: GEARAspiWDM (2.2.0.1),
Failed while scanning for CD / DVD drives, error 2500.
Virtual drives can sometimes interfere with reading and writing CDs in iTunes. If this is a virtual drive and you are having problems with other drives, try uninstalling the virtual CD application.
F: Unsupported CD or DVD drive.
Virtual drives can sometimes interfere with reading and writing CDs in iTunes. If this is a virtual drive and you are having problems with other drives, try uninstalling the virtual CD application.
Error Correction is turned on for importing audio CDs.

New Portable HD not found - Please Help

Similar Messages

Maybe you are looking for