New Ram failed

Hello, I have a Powerbook G4
1.67 GHz PowerPC G4
Memory: 512 MB DDR SDRAM
I have just added another 512MB DDR 2100, SO-DIMM Memory Module by Kingston.
After boot up the memory is not visable. When I veiw the hardware diagnostics the following info is provided:
Power On Self-Test:
Last Run: 29/03/2006 13:01
Result: Failed
Failure type: Memory
Memory slots: SODIMM1/J23REVERSED
Does anyone have any clues as to why it would fail?
Thanks

Vince,
Be careful when selecting your memory. Verify which model PowerBook you have. If it is indeed the 17-inch model find out if it is the current High Resolution (up to 1680x1050 resolution) 1.67GHz G4 or the previous 17-inch 1.67GHz.
While the newest High resolution 17-inch 1.67GHz G4 does indeed take a DDR2 PC2-4200 SO-DIMM, the older 17-inch takes a PC2700 DDR333 SO-DIMM. If you have a 15-inch 1.67GHz PowerBook you need not worry about differentiating as it only takes a PC2700 DDR333 SO-DIMM.
It is easy to get confused so check if your PowerBook suports a resolution of up to 1680x1050 if it is a 17-inch model before you buy. If not you are good to go with PC-2700 RAM.
Take care.

Similar Messages

New RAM problems with my Dual G4 1.25 MDD

Howdy I've had my Dual G4 1.25 MDD for 2 years and love it. I got it with 1GB RAM, thinking I was set. For Christmas I wanted to Upgrade the RAM to 2GB. from My PowerMac G4 Manual I knew I needed 2x 512MB PC2700 DDR333 CL2.5 SDRAM DIMM's.
I went to DealRam (part of DealMac) and found 18004memory.com The price seemed great $39 per stick. I ordered it and within a week got 2x 512MB DIMM's. Problem was it was the Wrong RAM spec. I tried that RAM in my Mac 30 different ways and Everytime the computer either wouldn't boot, or it would suffer Kernel Protection Faults. One time it did boot up but the RAM only recognized as 2x 256MB DIMM's. I called the company, got an RMA and returned the RAM, this time they sent me 2 replacement DIMM's.... for a POWERBOOK, SO-DIMM's. I returned it again and finally Got from them the
2x 512MB PC2700 DDR333 CL2.5 SDRAM DIMM's. They call it Hyperspeed RAM. Anywho, I powered down let the system cool over night and in the morning, popped it open, put the RAM in the 2 open slots DIMM2/J23 & DIMM3/J20. closed it back up and powered up. Everything was snappier, the boot was quicker and I checked About this Mac, it says 2GB. Apple System Profiler showed all 4 DIMM's and I thought everything was fine.
Computer ran great for hours, no issues. Everything seemed quicker. Computer went to sleep overnight, next day woke from sleep and Tried to use iTunes and during an extensive sort for Songs, the system Locked up. Nothing would work. Had to force restart. this time I tried to Run my favorite online Game, WoW and after it loaded and I started to play, within 5 mins the whole game locked up. The audio sound went into a sort of Loop, I couldnt force quit and had to force reboot. This happened several times. I finally decided to Run the Apple Hardware Test. The Quick test locked up after running 2mins. I let it sit for 1hr just in case it was still doing something and the progress bar and time never progressed. So i forced reboot, ran Test again this time as Extended test. at 8 min & 31 sec the test stopped and I got an Error Code, this time I wrote it down "2MEM/2/4: DIMM3/J20."
I guess that DIMM failed. I shutdown, popped open case, and removed DIMM3/J20 leaving the Original 1GB RAM and One of the 512MB Upgrades. I rstarted the Test again and Ran the Extended Test once more. It ran for 27mins & 24 secs and everything passed. So. 1.5GB is better than just 1GB. I powered down and powered back up to try and play WoW. Within 5 mins of loading game to play, everything locked up again.
So I took both of the new RAM out and left the Original 1GB RAM and ran Test everything was great no Errors. Rebooted, and went onto WoW again and was able to play for several hours. I quit game and shut down for night.
I have since Tried the 2x 512MB DIMM's in over 10 different variations in the computer with and without the original RAM and everytime I run a high end program or game (WoW, iTunes, and Photoshop), I get lock ups, crashes, and other screen weirdness.
I dont want to have to Return the Memory again. I am already out over $15 from s/h with RMA's.
PLEASE Any ideas what to do?
1 thing I noticed the RAM gets very very hot, when I've powered down tand removed the new RAM. I wonder if there is a cooling issue?
Anytime I put the Original 1GB RAM in, I dont have problems!

Hi lz3broc,
Sounds very much like faulty RAM to me, I'm afraid. I'm not sure about the temperature it's running at, but if the surrounding DIMMs aren't having a problem then I would definitely point the finger at those new memory sticks not being up to scratch.
If you were convinced it was temperature related then you could always try putting heat spreaders on the memory to help with cooling, but as these stick (semi-permanently) to the RAM then you would never be able to return them.
My personal opinion is that you should send the RAM back and buy two new DIMMs from Crucial Technology. I only ever buy RAM made by them and I've never had a problem with it - it's the same stuff Apple themselves generally use and works a charm every time. Probably not the news you wanted to hear, but that's probably the only way you're going to get a stable machine with 2GB RAM.
Hope that helps,
Andy.
PowerMac G4 Dual 1.50GHz Mac OS X (10.4.4) Liquid Cooled

Kernel Panic Message...Caused by new RAM???

Hey guys, just purchased 2x1gb ram from otherworldcomputing.com for my powerbook G4, im currently running the latest version I can possibly run which is 10.5.8 Everything seemed great when I put the RAM in, seemed like my computer was running pretty fast campared to the 512gb that came with the computer. All of a sudden, while im searching the web, it throws that kernel panic message up at me. I restarted and a few minutes later while im still on the web, bam, the same message.
I am currently in safe mode while Im writing this and nothing has happened yet(update:a few mintues after I finished typing this thread I received the same message, I have turned the computer off and jumped on my wiftes computer to type this I am thinking about putting the original 512mg ram back in to see if I get the message again)
Wierd, the first few days witht the new RAM everything seemed fine and then all of a sudden I got those messages. I have never had the problem ever before so it makes sense that its gotta be the new RAM right? Here are my specs
Model Name:          PowerBook G4 15"
Model Identifier:          PowerBook5,6
Processor Name:          PowerPC G4 (1.2)
Processor Speed:          1.67 GHz
Number Of CPUs:          1
L2 Cache (per CPU):          512 KB
Memory:          2 GB
Bus Speed:          167 MHz
Boot ROM Version:          4.9.1f1
Hardware UUID:          00000000-0000-1000-8000-0011243630A2
Sudden Motion Sensor:
State:          Enabled
Version:          1.0
This is the log from the 2nd kernel panic message that i copied and pasted for you guys
Process:         SystemUIServer [404]
Path:            /System/Library/CoreServices/SystemUIServer.app/Contents/MacOS/SystemUIServer
Identifier:      com.apple.systemuiserver
Version:         1.5.5 (248.9)
Build Info:      SystemUIServer-2480900~26
Code Type:       PPC (Native)
Parent Process: launchd [63]
Date/Time:       2012-04-08 11:31:41.326 -0500
OS Version:      Mac OS X 10.5.8 (9L31a)
Report Version: 6
Anonymous UUID: C89C038C-A8C3-4C08-B445-D420315A507C
Exception Type: EXC_BAD_ACCESS (SIGSEGV)
Exception Codes: KERN_INVALID_ADDRESS at 0x0000000002f61400
Crashed Thread: 0

To eliminate RAM being the problem, Look at this link: Testing RAM @ http://guides.macrumors.com/Testing_RAM Then download & use Memtest & Ramber.
Do you have an Apple Hardware Test disc (the AHT is on the Install/Restore DVD that came with your Mac)? Running the Apple Hardware Test in Loop Mode is an excellent troubleshooting step for finding intermittent hardware problems. It is especially useful when troubleshooting intermittent kernel panics. If Loop Mode is supported by the version of the Apple Hardware Test you are using, you run the Extended Test in Loop Mode by pressing Control-L before starting the test. Looping On should appear in the right window. Then click the Extended Test button.The test will run continuously until a problem is found. If a problem is found, the test will cease to loop, indicating the problem it found. If the test fails, be sure to write down the exact message associated with the failure.In some cases, RAM problems did not show up until nearly 40 loops, so give it a good run.
 Cheers, Tom

New ram crashes fcp

I just purchased new ram for the second day in a row. I bought four 1 gig ram sticks for my g5 power pc mac. I have a total of 6 gigs. I had previously had two gigs, 4 512 ram sticks.
Under about this mac, my new ram is reongized and other programs recongized the new ram (after effects).
I opened up FCP (5.0.4) project and fcp crashes everytime. I looked up my ram, and it is compatiable with my system. Crucial. i have the ram stickes in the proper slots.
http://www.crucial.com/store/mpartspecs.aspx?mtbpoid=1D1DFB01A5CA7304
The project I opened in fcp was done befrore the new ram (2 gigs) was installed. Can that be the issue, or is the ram I purchased not compatiable with FCP. At first FCP would crash after opening it, now it takes a few minutes before crashing. Would Resetting your Mac's PRAM and NVRAM help? Any tips and insight on installing and ram (ram suggestion) would also help.
Thankyou for taking your time and any suggestions will be helpfull and appericated.

I get our memory from Data Memory Systems in NH.
www.datamem.com not sure what the brand name is...
My machine has 4 slots.
DIMM0/J11 512Mb (Pre-installed)
DIMM1/J12 512Mb (Pre-installed)
DIMM2/J13 Empty
DIMM3/J14 Empty
I put a 512Mb chip in J13 & J14... The computer recognizes it, feels fresh and snappy, but without fail, it will crash after a short period of time forcing a 'hard' shutdown with the power button.
Steve

4 hrs later - Computer shut down after installing new RAM (mid 2007 Imac)

Mid 2007 imac and I installed new Ram. It worked for 4 hrs then the Imac shutdown. The pressed power button but no power. Unplugged and replugged the power cord and 3 beeps sounded. I am wondering if it worked for 4 hrs or so, then why did it would it fail 4 hrs later?
I am running the correct ram because in system profiler under memory - it said that everything was ok.
Any ideas?

or maybe the back tray wasn't tight enough?
I re-installed it now and so far so good.... I pressed tight and in an upwards motion. We'll see what happens

Three Beeps that will not go away after new RAM is installed

I have an old eMac I am trying to fix up. I got the three beep error message instead of the Macintosh startup BOOM. After finding this document on the website <http://support.apple.com/kb/HT1547> I thought it meant bad RAM. So I got two brand new 512mb since it appears to be this unit’s maximum <http://www.newegg.com/Product/Product.aspx?Item=N82E16820134390> . The eMac appears to be the 1.25ghz model (M9461LL/A). After I installed the new RAM, I am still getting the three beeps error message. Anyone have any ideas what this might going on?

If the eMac has not worked before for you, then maybe the logic board is gone as two bad banks would more indicate bad circuitry than two defective modules.
You could try Resetting the PRAM and NVRAM.
Also, make sure you have fully seated the RAM modules in all the way, they do require some gentle force, and failing that ... be glad that RAM is cheap today and you haven't done a lot of money.

TechTool Deluxe-Video RAM fails

New iMac running Leopard. It came with AppleCare and TechTool Deluxe 3.1.1. I did a check on my iMac, and Video RAM failed. I am wondering whether this is due to Leopard imcompatibility?(I did get a warning when I started TechTool). or there is something wrong with iMac. Thanks.

Try running the Apple Hardware Test and see what it says. I have heard of incompatibility if the Tech Tool Deluxe is not for Leopard. You could probably take the Tech Tool Deluxe back to Apple and ask for something that is current and will work with Leopard. They should be willing to swap out the disc for you if they have something more current on hand, or have a suggestion as to what to do. There might be a download.
Good luck!

New RAM installed but System Profiler still seeing old RAM

Hi
Recently put in a new hard drive after the last one failed. The new RAM, equaling 3GB, was installed on my iMac C2D 24" BEFORE the failure. I got it back from the shop today and checked to see if the RAM was still recognised. The System Profiler is showing 1GB or RAM, 512 in each slot, and the serial numbers match the RAM that came with the computer originally.
I'm running Snow Leopard and haven't noticed anything running slow. Is this just a glitch in the matrix?

So you are saying the original DIMMs are there plus the ones you added, all were recognized before the repair but only the Apple-supplied after the repair.
Just trying to keep all of this straight in my mind.
In that case, you might try removing the DIMMs you installed and reinstalling, one at a time and see if they are recognized. If they are not, then they may have gone bad for some reason, who knows why, and it is time to look at the warranty you have from the people from whom you purchased the DIMMs.
If it was someone like Crucial or OWC (macsales) they are really good about their lifetime warranty.
If the warranty is lifetime, contact the supplier and see what the process is for replacement.
It is strange that both would work, and then fail. But stranger things have happened with computers.

I am trying to install a new ram into my mac book air and i am having trouble finding it. can anyone help me through this?

can anyone help walk me through placing a new ram into a mac book air 2010 model

The RAM in a MacBook Air cannot be upgraded after purchase.
https://discussions.apple.com/message/12782306#12782306

Help! Installed new RAM and now screen isn't coming on!

Hi
I'm in a bit of a mess and would be grateful for any help with this one:
I have a Powerbook G3 500mhz Pismo that currently has a 512mb card in the top slot (Kingston PB100/512) that I installed about two years ago with no problems and an original 128mb in the bottom. At Christmas I bought another 512mb for the bottom slot – (Kingston KTA-PBG4/512 - This one is smaller than the first but it was the one reccomended by Kingston on their website for the Pismo).
I have just got round to installing it after backing up my system and I have good instructions on how to do it (I have replaced the HD two years previous with no problems)
Firstly I have to mention that just before I changed the RAM the laptop fell from a small stool (about 1.5feet high) onto carpet due to the unbalancing effect of taking out the battery/CD ROM. It landed on its edge where the power socket is. I immediately put it back together and turned it on to make sure it was ok - it came on fine and there were no problems visually, mechanically or otherwise, so I carried on with the installation.
I installed the new 512mb card in the bottom slot and re-assembled but when I turned it on the screen remained black! From the computer itself, however, it sounded as if it had started up ok – there was the chime and the familiar sound of the hard drive at start up.
To troubleshoot I removed the new RAM card and put back the old RAM as it was – this made no difference. I checked to see if the processor board was firmly in place or if I had dislodged any connectors by mistake within the area that I had worked but this made no difference. I also tried to re-set the parameter RAM and this made no difference.
Because the laptop took a small knock prior to installation, I am not sure if that has caused something to come loose or damage of some kind but as I mentioned I did test it immediately and it worked, so it’s either a delayed reaction or the new RAM card has caused it. – (As mentioned there is a difference between the two 512 cards in both name and size but the smaller size of the newer one I assume just reflects advancement in technology and it was reccomended by Kingston!)
If anybody has any advice on this I would be very grateful (and also, if anybody can point me in the direction of instructions on how to take the pismo apart to get to the connections to the screen that would be great – in case I have to do it)
Many Thanks Barry
PowerBook G3500mhz Mac OS X (10.3.9)

SpottyFox,
It sounds like you are properly seating the CPU card from your description, so I don't believe that is your problem. I am glad you checked the pins (I should have mentioned that as the next step if the reseating did not help). I cannot answer whether anything was damaged from your description of the pins; I have read where others have realigned bent pins with success so maybe your mileage will vary.
Start up your Pismo, then shine a flashlight directly into the display; if you can see data being written to the display, just the backlight is refusing to light. If this is the case, check the inverter board connections. The inverter is under the clutch cover and powers the fluorescent backlight in the display. Enlarge the bottom picture in this link to see the inverter:
http://www.ifixit.com/Guide/Mac/PowerBook-G3-Pismo/Inverter-Page-10-Inverter
Check connections at each end of the inverter. Disassembly is not as extensive as this guide suggests. Support the back of the display, then remove the main battery, optical drive, lay the keyboard on its face on the palm rest, heat shield, and clutch cover...that's it.
http://www.ifixit.com/Guide/6.0.0.html
You might also connect the Pismo to an external display; failure here would suggest a more serious problem.

Installed new RAM now computer wont start up

I just installed 2GB of RAM in my iMac and removed the 512mb card it had originally.when i pressed the power button it beeps fast a few time then the fan starts working really fast. The screen doesnt turn on only the sleep light blinks as the fan runs. I replaced one of the new cards with the original 512mb card and it starts but when i check the memory the slot where the new 1GB card appears "empty" why could this be? did i install incorrectly?

When you install new RAM you have to push much harder than you think you should. You won't damage the RAM, but you have t give a mighty push to seat it, make sure you hear a click.

Power Mac G5 Refuses to start with new RAM!

I have a Power Mac G5 Dual 1.8GHz June 2004. I know I read somewhere online that it takes 1GB sticks of RAM, and that it has to be dual channel. I went to Best Buy today and got myself 2 sticks of 1GB DDR PC3200 "Compatible with 400/333/266MHz" Dimms, and installed them in pairs. When I start them with or without my old memory, my mac starts up, makes no noises, but the fromt white LED light blinks 2 times, and does this repeadedly until I shutdown and install the old 512MB sticks. I need to get this new RAM to work in here, I just paid $112 total for 2 sticks, and I am not ready to go back to the store yet. Is there something I am missing here? Something I am not doing right?
New RAM Specs:
1GB DDR Dimm,Q PNY Technologies, PC3200 "Compatible with 400/333/266MHz"
I need to get this to work on my machine! Thanks for any help.

Is there something I am missing here?
Not all RAM is created equal and seldom does over the counter PC RAM work in a G5.
Buy and install ONLY guaranteed Mac compatible RAM.
http://eshop.macsales.com/shop/memory/PowerMac-G5-Memory
BTW, you paid too much.
When I start them with or without my old memory, my mac starts up, makes no noises, but the fromt white LED light blinks 2 times,
That means "Incompatible RAM types".
http://support.apple.com/kb/ht1547
I am not ready to go back to the store yet.
Go back to the store.

Random restarts and freezes. Just upgraded my RAM trying to diagnose new RAM as the problem but they pass Rember test.

Hey so I have been dealing with random reboots and computer freezes since upgrading my RAM. I also reinstalled my 10.8.2 at the same time I upgraded my RAM. I have a Mac Mini Mid 2011 with the OWC Data Doubler Kit and a Crucial M4 128GB Boot drive. My computer reboots every 30 minutes or so and sometimes completely freezes up. I am trying to figure out if the new RAM is the issue as I can send them back. I have ran several Rember RAM tests but the computer freezes mid test so I can not see the issue. All other times it completeles the RAM test with no issues.
Any help is greatly appreciated!
Here is my last crash report:
Thu Mar 7 15:34:36 2013
panic(cpu 0 caller 0xffffff8009ab7b95): Kernel trap at 0xffffff8009a76c4e, type 14=page fault, registers:
CR0: 0x000000008001003b, CR2: 0xffffffa00cffad88, CR3: 0x000000000582b00c, CR4: 0x00000000000606e0
RAX: 0x0000000000000000, RBX: 0xffffff800d17f488, RCX: 0x0000000000000000, RDX: 0xffffff800a0bd430
RSP: 0xffffff80fa013d10, RBP: 0xffffff80fa013d60, RSI: 0x0000000000000000, RDI: 0xffffff800d17f488
R8: 0xfffffffffffff000, R9: 0xffffff801b50b5d0, R10: 0x000000010ccc3000, R11: 0x0000000000000200
R12: 0xffffffa00cffad78, R13: 0x000000000000007d, R14: 0x0000000000000000, R15: 0x0000000000000000
RFL: 0x0000000000010293, RIP: 0xffffff8009a76c4e, CS: 0x0000000000000008, SS: 0x0000000000000010
Fault CR2: 0xffffffa00cffad88, Error code: 0x0000000000000000, Fault CPU: 0x0
Backtrace (CPU 0), Frame : Return Address
0xffffff80fa0139b0 : 0xffffff8009a1d5f6
0xffffff80fa013a20 : 0xffffff8009ab7b95
0xffffff80fa013bf0 : 0xffffff8009ace4ad
0xffffff80fa013c10 : 0xffffff8009a76c4e
0xffffff80fa013d60 : 0xffffff8009a7be07
0xffffff80fa013d90 : 0xffffff8009a75cf4
0xffffff80fa013dc0 : 0xffffff8009a75150
0xffffff80fa013e00 : 0xffffff8009a66b2c
0xffffff80fa013ef0 : 0xffffff8009a6a890
0xffffff80fa013f20 : 0xffffff8009db8d66
0xffffff80fa013f50 : 0xffffff8009de17da
0xffffff80fa013fb0 : 0xffffff8009acecf3
BSD process name corresponding to current thread: syslogd
Mac OS version:
12A269
Kernel version:
Darwin Kernel Version 12.0.0: Sun Jun 24 23:00:16 PDT 2012; root:xnu-2050.7.9~1/RELEASE_X86_64
Kernel UUID: 8D5F8EF3-9D12-384B-8070-EF2A49C45D24
Kernel slide:     0x0000000009800000
Kernel text base: 0xffffff8009a00000
System model name: Macmini5,1 (Mac-8ED6AF5B48C039E1)
System uptime in nanoseconds: 151583130298
last loaded kext at 11211562865: com.apple.driver.AppleHWSensor          1.9.5d0 (addr 0xffffff7f8b414000, size 28672)
loaded kexts:
com.apple.driver.AppleHWSensor          1.9.5d0
com.apple.driver.AudioAUUC          1.60
com.apple.iokit.IOBluetoothSerialManager          4.0.9f8
com.apple.filesystems.autofs          3.0
com.apple.driver.AppleUpstreamUserClient          3.5.10
com.apple.iokit.IOUserEthernet          1.0.0d1
com.apple.driver.AppleMikeyHIDDriver          122
com.apple.driver.AppleMCCSControl          1.0.33
com.apple.driver.AppleHDAHardwareConfigDriver          2.3.0f2
com.apple.driver.AppleTyMCEDriver          1.0.2d2
com.apple.driver.ApplePlatformEnabler          2.0.5d4
com.apple.driver.AGPM          100.12.69
com.apple.driver.AppleMikeyDriver          2.3.0f2
com.apple.driver.AppleIntelHD3000Graphics          8.0.0
com.apple.iokit.IOBluetoothUSBDFU          4.0.9f8
com.apple.driver.AppleHDA          2.3.0f2
com.apple.Dont_Steal_Mac_OS_X          7.0.0
com.apple.iokit.BroadcomBluetoothHCIControllerUSBTransport          4.0.9f8
com.apple.driver.AppleSMCPDRC          1.0.0
com.apple.iokit.AppleBCM5701Ethernet          3.2.5b3
com.apple.driver.AppleMuxControl          3.2.6
com.apple.driver.ApplePolicyControl          3.2.6
com.apple.driver.AirPort.Brcm4331          600.15.20
com.apple.driver.AppleLPC          1.6.0
com.apple.driver.ACPI_SMC_PlatformPlugin          1.0.0
com.apple.driver.AppleIntelSNBGraphicsFB          8.0.0
com.apple.iokit.SCSITaskUserClient          3.5.1
com.apple.driver.AppleIRController          320.15
com.apple.driver.AppleFileSystemDriver          3.0.1
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless          1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib          1.0.0d1
com.apple.BootCache          34
com.apple.driver.XsanFilter          404
com.apple.iokit.IOAHCIBlockStorage          2.2.0
com.apple.driver.AppleUSBHub          5.1.6
com.apple.driver.AppleFWOHCI          4.9.5
com.apple.driver.AppleSDXC          1.2.2
com.apple.driver.AppleAHCIPort          2.4.0
com.apple.driver.AppleUSBEHCI          5.1.5
com.apple.driver.AppleUSBUHCI          5.1.5
com.apple.driver.AppleEFINVRAM          1.6.1
com.apple.driver.AppleHPET          1.7
com.apple.driver.AppleACPIButtons          1.6
com.apple.driver.AppleRTC          1.5
com.apple.driver.AppleSMBIOS          1.9
com.apple.driver.AppleACPIEC          1.6
com.apple.driver.AppleAPIC          1.6
com.apple.driver.AppleIntelCPUPowerManagementClient          196.0.0
com.apple.nke.applicationfirewall          4.0.39
com.apple.security.quarantine          2
com.apple.driver.AppleIntelCPUPowerManagement          196.0.0
com.apple.iokit.IOSerialFamily          10.0.6
com.apple.kext.triggers          1.0
com.apple.iokit.IOSurface          86.0.2
com.apple.driver.DspFuncLib          2.3.0f2
com.apple.iokit.IOAudioFamily          1.8.9fc9
com.apple.kext.OSvKernDSPLib          1.6
com.apple.iokit.IOBluetoothFamily          4.0.9f8
com.apple.driver.AppleSMBusController          1.0.10d0
com.apple.iokit.AppleBluetoothHCIControllerUSBTransport          4.0.9f8
com.apple.iokit.IOEthernetAVBController          1.0.2b1
com.apple.iokit.IOFireWireIP          2.2.5
com.apple.driver.AppleHDAController          2.3.0f2
com.apple.iokit.IOHDAFamily          2.3.0f2
com.apple.driver.AppleBacklightExpert          1.0.4
com.apple.driver.AppleGraphicsControl          3.2.6
com.apple.iokit.IONDRVSupport          2.3.4
com.apple.iokit.IO80211Family          500.15
com.apple.iokit.IONetworkingFamily          3.0
com.apple.driver.AppleSMC          3.1.3d11
com.apple.driver.IOPlatformPluginLegacy          1.0.0
com.apple.driver.IOPlatformPluginFamily          5.2.0d16
com.apple.driver.AppleSMBusPCI          1.0.10d0
com.apple.driver.AppleThunderboltEDMSink          1.1.8
com.apple.driver.AppleThunderboltEDMSource          1.1.8
com.apple.iokit.IOGraphicsFamily          2.3.4
com.apple.driver.AppleThunderboltDPOutAdapter          1.8.5
com.apple.driver.AppleThunderboltDPInAdapter          1.8.5
com.apple.driver.AppleThunderboltDPAdapterFamily          1.8.5
com.apple.driver.AppleThunderboltPCIDownAdapter          1.2.5
com.apple.iokit.IOSCSIBlockCommandsDevice          3.5.1
com.apple.iokit.IOUSBMassStorageClass          3.5.0
com.apple.iokit.IOSCSIArchitectureModelFamily          3.5.1
com.apple.iokit.IOUSBHIDDriver          5.0.0
com.apple.driver.AppleUSBComposite          5.0.0
com.apple.iokit.IOUSBUserClient          5.0.0
com.apple.driver.AppleThunderboltNHI          1.6.0
com.apple.iokit.IOThunderboltFamily          2.0.3
com.apple.iokit.IOFireWireFamily          4.5.5
com.apple.iokit.IOAHCIFamily          2.2.0
com.apple.iokit.IOUSBFamily          5.1.6
com.apple.iokit.IOHIDFamily          1.8.0
com.apple.driver.AppleEFIRuntime          1.6.1
com.apple.iokit.IOSMBusFamily          1.1
com.apple.security.sandbox          220
com.apple.kext.AppleMatch          1.0.0d1
com.apple.security.TMSafetyNet          7
com.apple.driver.DiskImages          344
com.apple.iokit.IOStorageFamily          1.8
com.apple.driver.AppleKeyStore          28.18
com.apple.driver.AppleACPIPlatform          1.6
com.apple.iokit.IOPCIFamily          2.7
com.apple.iokit.IOACPIFamily          1.4
com.apple.kec.corecrypto          1.0

Reinstall the original memory and see whether there's any improvement. Be careful not to touch the gold contacts on the memory modules when handling them. If necessary, clean them with a mild solvent such as rubbing alcohol.
The Apple Hardware Test, though generally unreliable, will sometimes detect a fault. A negative test can't be depended on. Run the extended version of the test.

My old PC died but hard drive is still functional. Purchased new PC and downloaded latest iTunes but attempts to transfer folder with songs from old hard disk to new computer failed. Only 20 of approx 300 songs transferred ??

My old PC died but the hard drive is still functional and accessible using a USB extraction device. I purchased a new PC and downloaded the latest iTunes but attempts to transfer the iTunes folder with songs from the old hard drive to my new computer failed. Only 20 of approx 300 songs transferred. All other non music file transfers (WORD, EXCEL, etc) from the old hard drive to the new computer were successful. Is this a file type issue? Any thoughts?? THANKS!

iTunes: How to move [or copy] your music to a new computer [or another drive] - http://support.apple.com/kb/HT4527

My new RAM doesn't work with my iMac.

Hello,
I bought new RAM 4GB PC10600 DDR3 1333MHz SO-DIMM to installed in my iMac 3.4 GHz intel core i7, osx lion.
I try to installed it alone without original RAM (2GB * 2 pcs) installed to check how it works.
After press start button, there are 3 beep sounds and iMac won't start.
I try to reset PRAM follow the instruction, but it won't work. Because there are 3 beep sounds alarm immediately after press start.
Does my RAM have a problem?

My iMac has 4 memory slots and I try to installed one by leave 3 slots empty.
By the way this is the 2nd ram I purchased from OWC with same spec as the last one (also same as link above) but different in purchase date (about 2 weeks different).
So now I have 2 GB *2 pcs (come with iMac) and 4GB * 2 pcs from OWC.
So I'm quit sure that this ram is compatible with my iMac because the first one is work.
But I have some notice,
For the 1st RAM I bought from OWC (4GB PC10600 DDR3 1333MHz SO-DIMM), when first installation it also didn't work. I can't start iMac. And after 2 weeks, I try to installed it to my iMac again, now it can operate as normal. What do you think about it?

New Ram failed

Similar Messages

Maybe you are looking for