New router, Range extender or Powerline network adapter?

Have WRT310N router connected to my desktop in the basement. The signals are very weak upstairs when use my laptop.
Have just purchased a new Samsung Smart TV (located upstairs).
To get stronger signals for streaming, internet connection on TV and laptop what should I be getting?
new router i.e. EA4500, range extender or powerline adapter.
Thanks

I have used range extenders and they do work but you should know that the wireless range extenders are 'repeaters' they capture the signal and rebroadcast it. Therefore the throughput you get with a range extender will typically be less than 50% of the speed of similar router.
If you have the ability to run an ethernet cable between the two rooms I would suggest a 2nd router setup as an access point.
If you can't get ethernet to the 2nd room then I would suggest powerline, In fact I'm currently running a E4200 V1 router with one of it's lan ports connected to a Trendnet powerline adapter and then I have a second Powerline adapter in a room where I couldn't get an ethernet cable the second powerline adapter is connected to a WRT350N router set up as an switch, for devices such as an Xbox and Blu-Ray Player.

Similar Messages

I want to extend the range of my Time Capsule, can I use Universal WiFi Range Extender, 4-port WiFi Adapter WN2000RPT?

I want to extend the range of my Time Capsule, can I use Universal WiFi Range Extender, 4-port WiFi Adapter WN2000RPT?

A universal may work but reliability tends to be poor..
You are much better using another airport .. extreme or express.. even a second hand older one.
Or do not use wireless bridge or repeater.. simply run ethernet or use EOP adapters to a second WAP run independently of the main router.. it is far more reliable and far faster solution .. wireless bridge/repeater will halve your wireless speed.

Can i use another router to extend my wireless network of my airport extreme?

i have a billion router (moddel BiPAC 7300W) I just got myself the airport extreme, i want to use the extreme as the main router and extend the network using the billion router.
steps i have followed on the extreme is as follows:
INTERNET
connection sharing: Distrobute a range of IP addresses
cofig IPv4:set to my home network range(manually) - ip,subnet,router,dns
DHCP
access control: mac address of billion router set to all day every day
steps i have followed on the billion router:
disabled NAT
disabled DHCP
ethernet address: same range as extreme ip, actual ip op extreme is xxx.xxx.xxx.254, on billion xxx.xxx.xxx.253
disabled RIP
set wireless mode to 802.11b+g+n
channel id: auto
channel width:20/40mhz
disable wps
disable vmm
Wireless Distribution System (WDS) - added the 3 mac addresses the utility displayed, 5ghz and 2.4ghz and also the ethernet.
restarted both routers, not picking up all the devices connected to the network.
can any one please help me?

i want to use the extreme as the main router and extend the network using the billion router.
Unfortunately, WDS was never adopted as an official standard in the industry, so very few routers from other manufacturers are known to be compatible with Apple's WDS settings. The known devices are as follows:
Belkin F5D7230-4 and F5D7231
BT Voyager 2091 or 2100
Buffalo WGR-G54
Linksys WRT54G or WRT54GS (through version v4)
Netgear WGR614 v6
Thompson 585v6 wireless router (40 bit WEP works but stronger encryption does not)
connection sharing: Distrobute a range of IP addresses
You would not use this setting unless your service provider has furnished you with a specific range of IP addresses to use for your devices. Is that the case?
Normally, when the AirPort Extreme is functioning as the "main" router, the setting for Connection Sharing is set to "Share a public IP address"
Wireless Distribution System (WDS) - added the 3 mac addresses the utility displayed, 5ghz and 2.4ghz and also the ethernet.
You indicated that you had configured things this way on the Billion router. But, you did not indicate whether you had set the Wireless Mode for the AirPort Extreme to "Participate in a WDS Arrangement".
If you have not already done so, this might improve your chances of establishing a connection between the AirPort Extreme and Billion router for the WDS.
To access these settings on the AirPort Extreme, you would need to open AirPort Utility and click Manual Setup. Then click the Wireless tab just below the row of icons. Change the setting for Wireless Mode to "Participate in a WDS Arrangement".
Note....you may need to hold down the option key on your Mac, (or it might be alt or control if you are using a PC) to display the WDS setting.
Once you do this, then a WDS tab will now appear next to the Wireless tab. Click on the WDS tab to set up the AirPort Extreme as the WDS Main and enter the MAC address of the Billion router.
As I mentioned previously, it is extremely unlikely that the Apple and Billion devices will be compatible for WDS, but probably worth a try....since you never know when something just might work.
Even if it does....WDS operates only at "g" wireless speeds, so you will lose any of the faster "n" speed capabilities of the AirPort Extreme in this type of setting.
Please post on your results.

WRT54GX4 Wireless Router and Xbox 360 Wireless Networking Adapter

I just got an Xbox 360 with a Wireless Networking Adapter. The adapter will recognize the network, but won't connect to it. Even if I remove the security, the Xbox 360 won't connect. Is there something else via the router I'm supposed to be doing? I called Microsoft and they said to open the port settings, but I don't know if that's really the issue and I don't know how to do that if I need to.
The ports they gave me were:
TCP 80
UDP 88
UDP 3074
TCP 3074
UDP 53
TCP 53
Thanks for any help if you can.

Open an Internet Explorer browser page.In the address bar type - 192.168.1.1
Leave username blank & in password use admin in lower case...
Click on "Applications and Gaming" tab and then click on "Port Range Forwarding" subtab...
1) On the first line in Application box type in ABC, in the start box type in 88 and End box type in 88, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
2) On the second line in Application box type in PQR, in the start box type in 3074 and End box type in 3074, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
3) On the third line in Application box type in XYZ, in the start box type in 53 and End box type in 53, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box and click on Save Settings...
3) Once you return to the set up page click on the Security tab and uncheck Block Anonymous Internet Requests and click on Save Settings...
4) Click on set-up and change the MTU Size to 1452 and click Save Settings...
5) Goto the XBox Network Settings and IP Address Settings and select manual IP Settings and assign the following on your Xbox
IP Address :- 192.168.1.20, Subnet Mask :- 255.255.255.0, Default Gateway :- 192.168.1.1...
6) Also assign the DNS Addresses on the Xbox
Primary dns :- 4.2.2.2...Secondary dns :- 192.168.1.1
7) Turn off your modem, router, and Xbox...Wait for a minute...
8) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the Xbox and test it...it will connect...

Wireless Router Range extender?

Hi, I just got a modem with a built in wireless router, but I already have another wireless router that I'd like to use to extend my wireless network, so that my main modem will wirelessly connect to my original wireless router.
Does anyone know how I can do this? So far I'm having no luck getting it to work.

Use the web browser setup procedure to manually configure the network information on the extender. The push button requires specific network settings and the router may not use the settings required by the extender.

Router Range Extender

I have a WRT 160N router and was wondering if some elelctronic unit is available which can pickup its signal at
close to the end of its range and re-broadcast the signal?
Thanks

I think your should Try to go for a Range Expander (WRE54G) or and access point WAP200. This are the Devices which will expand the Wireless Range.

Using old WRT54GS as a range extender?

Good morning!
I first want to say I "think" I might be posting in the wrong forums for this question, but because I'm not really sure what the proper terminology for this is, I thought it best to ask here.
I have recently upgraded my router for my home network from an old Linksys WRT54GS G router, to a new E2500 N router. I have heard/read that it is possible to reconfiqure my old router to act as a range extender for my network but I am unclear how to do so. I think this may be the same thing as an access point, but all the FAQ's I've found seem to have this work as a solo device, not as a device on existing network. I have my e2500 setup with the modem in my study and broadcasting from there, and would like to use my old G router set up as a range extender to be located in the front living room area and picking up the network signal and rebroadcasting from there without a modem or computer attached.
I would like to know if this is possible, and if so, could someone please post a link to a FAQ that might help me set it up properly? Thank you for any and all help on this and hope everyone has a great day!

Sure it's easy. Have you searched the forum for your information? In the upper right search area type in 'two routers'.

Probelm the network adapter could not establish connection

Hi Everyone ,
i installed the Sqldevelopr version 2.1.0.63 in windows vista , but when i start new connection its shows me error (network adapter could not establish connection)
but it's work when i used sql plus , i tried many times but it shows me same error what should i do?.
detailes for connection as bellows
connection name=orcl
username=scott
sid=orcl
port=1521
Best Regards
anwar

You should post your question in [SQL Developer|http://forums.oracle.com/forums/forum.jspa?forumID=260] forum
Edited by: Oleg Gorskin on 28.12.2009 6:21

New router vs range extender

I have a Linksys WRT120N with two desktops connected via wired connections.
In the house, there are two students accessing the Internet through WiFi via the WRT120N.
One of the laptops (on an Apple laptop) seems to lose its' connection from time to time.
The other laptop (Lenovo) is located the furthest distance from the router and only gets two bars signal strength.
Would my best option to improve the signal strength for the Lenovo laptop and hopefully, also increase reliability for the Apple laptop be to purchase a new router such as a Linksys E1500 with speed boost or would it be best to try a Linksys range extender (RE1000)?
Thank you.

Also, check the wireless adapter drivers of the Mac laptop. It may be outdated.
"Don't fix it if it ain't broken."

I purchased a new Time Capsule (2TB - 2013), and I would like to use my old Time Capsule to extend the range of my wireless network.

I purchased a new Time Capsule (2TB - 2013), and I would like to use my old Time Capsule to extend the range of my wireless network. I can't get them to communicate. Any ideas?

You need to use the airport utility on a computer.
If you use v6 utility it is fairly easy and straight forward.
The trick is to place the old TC in the same room as the new one.
Do a full factory reset and then you can just go through the utility to extend wireless network.
I did one post with all the pictures.
https://discussions.apple.com/message/24161378#24161378
If you have issues just ask.
Then you can place the old TC about half way between the new TC and the clients would want to connect.. the half way point is not distance but wireless signal levels.
You can pick that up by using the wireless diagnostics in a mac laptop and walking around to pick up the signals.
This is for extend wireless.. if you want roaming network it is entirely different. That means they are plugged together with ethernet.
Tell us if you mean roaming not wireless extend.

New Intel WIFI Wireless Network Adapter does not recognize Wireless Router

I have had a Linksys BEFW11S4 Version 4 Wireless router for quite some time. It works like a champ and I have one Laptop wired to it and a second using Wireless working just fine. Recently, I received a new ThinkPad W500 Laptop with an Intel WIFI Link 5100 AGN wireless network adapter. The older laptop that works just fine with the router uses a
11a/b/g Wireless LAN Mini PCI Express Adapter by Atheros. However, the NEW laptop with the Intel Adapter fails to connect to the Router. It will either indicate a failure while "Waiting for Association" or it will indicate a failure when waiting to "renew IP Address". Sometimes, it will show a signal strength close to ZERO (Even as the older laptop with the other adapter is showing a signal strength close to 100%) When I called Linksys support, I was told that the facts that the Router (a) works find with the wired Laptop and (b) works fine with the 11a/b/g NEtwork Adapter and (c) works fine when WIRED to the new laptop all indicate that the problem is NOT with the router at all -- but with the Network Adapter. Can anyone tell me what has to be adjusted in the Adapter settings? Right now, I am using IBM Access Connections for BOTH of the wireless laptops. I have made sure to set IDENTICAL values for SSID and WEP (128-bit) [static] password. I have also ensured that all OTHER settings are the same for the two laptops. Yet, in one laptop, there is NO PROBLEM while in the other, I can not get the Wireless Adapter to "see" the signal from the Router. TO further check this, I have [temporarily] disabled the WEP password, enabled SSID broadcast, and disabled the MAC address restrictions that I put in (so that the system would be totally "open") yet the Intel Adapter STILL did not "find" anything. In addition, when I use the "Find WIFI" feature in Access Connections, I find that SOMETIMES the network with SSID is found and sometimes, it will display "unknown network" and not pick up the SSID.
This is all very frustrating. If anyone has experience with the Intel WIFI Link 5100 AGN Adapter, I would appreciate any hints, tricks, ideas, etc.
Think you!!!!
--Zvi

I installed the LATEST version of IBM Access Connections as well as verifying that I have teh LATEST drivers for the Intel Wireless NEtwork Adapter.
What now happens is that I am able to authenticate to the Router. However, I get a failure on "renewing IP Address" -- which [according to the diagnostic message] means that the Rotuer fails to provide me with an IP address to use. Do you have any suggestions?

I've bought a new computer and can't seem to get my router & network adapter set-up

I just bought a faster computer and when trying to install the software for my router (BEFW11S4) and network adapter (WUSB11) I'm getting an error that I need to be connected to the internet.
DUH! The whole point of installing these 2 is so that I can get to the internet.
I'm not sure what I'm doing wrong.
Can someone give me step by step "wireless for dummies" terms on how to install on the new computer? Someone told me that I shouldn't be trying to configure the router so I'm not sure if that's the problem.
Any help I could get would be great!
Thanks,
Robin

ok./...first the adpater....
insert the setup disc into the cd rom....exit the linksys screen when it pops up....
now plug in the WUSB11....you will get a found new hardware....hit next and then select the "automatic" option....hit next and windows should search for the drivers and install them. ( if you are trying to use the ELA ot ELC ....don't do so )
As far as the router is concerned....the config depends upon your ISP....if it's a cable connection....turn off all devices....then turn on the modem , router and PC ( in this order) ....check if you are going online.....if not...., in the browser key in http://192.1681.1 "admin" is the password....once in the setup page....click on MAC address clone....select enable and then "clone"....save settings....power cycle again and check if you are online.....
In case you are using a DSL....go to the setup page of the router , and from under "internet connection type' select PPPoE....enter your username and password...save settings and check if you are going online....

I have bought a TC to extend the range of the wireless network in the house and would like someone to explain the best way to do this? My combine router/modem is supplied by Movistar(in Spain) model Xavi 7958 router ADSL with four ethernet ports.

What is the best way to extend my wireless network in the house using a TC? I currently use a combined router/modem supplied by Movistar(live in Spain) model XAVI 7958 router ADSL with four ethernet ports. What is the best configuration and can you explain what is meant by bridging and which is best to bridge for signal strenght TC or Xavi modem/router? Have ipads, iphones, apple tv...etc and want a connection them all in the whole house which, not just downstairs, to our wireless network.

You cannot wireless bridge Apple to non-apple router.. so that is out.
The only way you can do this is run ethernet or EOP adapters.. and place the TC in a location where the other apple idevices can reach it.
If you want to repeat wireless with apple routers you have to use another apple router next to the modem.. plugged in an running as an AP.
Basically the TC is the wrong piece of equipment unless you want Time Machine backups.. take it back and buy a universal repeater.. not apple. Or buy more apple stuff like an extreme or express.. one apple router is useless to you without running ethernet.

How to extend range of my wireless network with an Airport Express connected by ethernet with Airport Utility 6.0

Hi everyone,
I have AirPort Express 802.11n (1st Gen) firmware 7.6.1, that is connected to my main wifi base station (a TimeCapsule) by ethernet. I would like to extend the range of the Wifi Network but am not clear on how to do so using the new interface of Airport Utlity 6.0.
Does anyone have any tips on how to do this?
BR
AK

Hi Everyone!
Many thanks for the tips. I have downloaded 5.6 and have set my Airport Express in the "Extend a wireless network" mode. I was still having a few problems with the quality of the wifi connection in different parts of my apartment (by no means a very large one, but walls seem to be made of extra dense concrete here in Singapore) and went out and bought a few powerline adapters by TP Link (http://www.tp-link.sg/products/details/?categoryid=1862&model=TL-PA211#spec).
If you don't mind a slightly long post, I would be very grateful for any tips:
My setup is now as follows:
Main room
Time Capsule - connected to a Cisco DPC3925 Modem (http://www.cisco.com/web/consumer/support/modem_DPC3925.html) both connected to a TP Link adapter 1.
iMac - connected via Ethernet to TP Link adapter 2 and wifi enabled
Airport Express 1 - connected by Ethernet to TimeCapsule (and thus TP Link adapter 1) used to stream audio to a stereo that doesn't have an optical cable input. Since it is an Ethernet connection, I have wifi turned off.
Apple TV 1 - connected by Ethernet to TimeCapsule (and thus TP Link adapter 1)
Bedroom A
Airport Express 2 - connected via ethernet to TP Link adapter 3
Bedroom B -
Apple TV 2 - connected by Ethernet to a TP Link adapter 4
After following the tips on setting up the extended wifi network, I find that when I use a wireless client (e.g. iPad, Macbook air, etc) in either Bedroom B or Bedroom C (both don't have wifi in the room) the connection is very poor. Even more odd is that the connection in Bedroom A, one that does have Airport Express 2. To be clear when I mean very poor, I mean Skype/facetime skips frames and freezes... this doesn't happen when I am in the main living area.
I would be very grateful for tips on how to set up the most robust network given the configuration above. Specifically, I am wondering about:
When I select Extend a wireless network option on Airport Utility 5.6 the summary page states that it is connecting using "Wireless Network" vs what I would expect it to say "Ethernet connection".
Is there any advice on whether to enable 5Ghz network and if so, should I try to use that for the various wifi clients?
Does anyone know if I can somehow use Apple products to extend the reach of the Cisco DPC3925? Frustratingly the signal is quite strong (compared to Apple routers), but I cannot properly stream audio/video if that wifi network is used (as my iMac that hosts the content is on the Apple one... and I'd have to walk over to switch it to the Cisco one).
Any other tips would be much appreciated!
Cheers!
AK

How do I add an Airport Express to extend the range of my WIFI network with my iMac as a base station?

Hi people
I need help to configure a new Airport Express only to extend the range of my WIFI network.
My ethernet cable from modem is connected directly in my iMac and I am sharing the internet by WIFI inside home very fine.
Now, I would like connect my devices on my garden on backyard.
I can't move my iMac from their place and i just want add a Airport Express between the iMac and backyard to extend the range of WIFI.
But I can't to configure to that. On Airport Utility appear the Airport Express connected directly to internet globe, but don't work.
So, what can I do? What is wrong?
Thanks all and best regards.
Carlos Sgrillo, from Brazil.

The AirPort cannot do what you ask.
The Airport needs to connect to a modem, or another router......not to a computer.
The Express can only extend a wireless signal that has been provided by another Apple router.

New router, Range extender or Powerline network adapter?

Similar Messages

Maybe you are looking for