New SCSI hard drive problem: Device busy too long

I set up second SCSI hard drive for my sun box Sparc Station 20. The set up is as follows:
New SCSI hard drive (ID #2) connects to Sun box and connects to tape drive (SCSI #4) with terminator.
Hard drive is Seagate model ST15150N with J01 (open : means disable drive terminator) and J04 (jumper on second position, ID=2).
I CAN format the hard drive and assign label etc.. but when I type the command : > newfs /dev/rdsk/c1t2d0s7 (I use whole slice 7 as one partition and c1 is my second controller).
The following error displays continuously:
WARNING: /iomnn@f,e0000000/sbus@f,e0001000/dma@1,81000/esp@1,80000/sd@2,0 device busy too long
Is this error come from the wrong hardware set up or from other reason ? Any suggestion is welcome . Thanks in advance.
William

First of all, thanks for your reply. I appreciate it.
A couple of things. I check my system profiler and I couldn't find out what kind of SCSI card I have. I even opened up my machine and there wasn't any writing on it. So how do I find out what type of card I have? My other question is if the same card worked for the SCSI drive I had before, why won't it work on the new drive. I've set it as the master at the end of the SCSI cord and like I said I used CCC. The drive shows up on my desktop but won't boot. Should I try loading OS from disks instead of using CCC?

Similar Messages

Solaris 8 IA "Device busy too long"

The installation of Solaris 8/IA proceeds completely fine. However, when the system is to boot on it's own as the last step, I get the following error: "device busy too long." I've tried many different configurations for the SCSI card and I have followed the "device configuration guide." What could be causing this? It seems as though Solaris is completely happy with the hard drive and CD ROM during installation. Why are things different during runtime?
I am using an Adaptec 2940AU SCSI card with a SCSI hard drive and with a SCSI CD ROM.
Thanks in advance.

Thanks for responding to my message concerning the "device busy too long."
Before configuring the system I purchased components that were supported in the hardware compatibility list. Most importantly, the motherboard is an ASUS P3B-F and the SCSI card is an Adaptec AHA-2940AU. I read and followed the advice in the Solaris 8 Configuration Guide, the Adaptec literature, and the specs for the SCSI hard drive. I think I've tried every combination available.
As a check I installed Windows 2000 on the system to make sure that there was fundamental compatibility. The OS installed without any problems the first time!! The system booted and operated completely stable. So I must assume that the components basically work together.
I would like to know what Solaris is checking to arrive at a "device busy too long" state. If I knew this, perhaps I can solve the problem.
Thanks again!! This sure is frustrating.

New SCSI Hard Drive Won't Boot

Hello,
I have a problem. My original SCSI drive died on me and I took it out and converted over to only ATA drives. Ever since I did that, my computer has always been a bit lagging. Slow. Not too fast. Anyway, I bought another SCSI drive and I'm trying to use that as my boot drive. I used Carbon Copy Cloner and checked "make bootable" in the preferences, but for some reason my computer just won't boot from it. I've formatted it and it shows up on my desktop, but it won't boot. Start. Make OS go boom boom. I would appreciate any help I could get. Thanks in advance.

First of all, thanks for your reply. I appreciate it.
A couple of things. I check my system profiler and I couldn't find out what kind of SCSI card I have. I even opened up my machine and there wasn't any writing on it. So how do I find out what type of card I have? My other question is if the same card worked for the SCSI drive I had before, why won't it work on the new drive. I've set it as the master at the end of the SCSI cord and like I said I used CCC. The drive shows up on my desktop but won't boot. Should I try loading OS from disks instead of using CCC?

New internal hard drive problems

Thanks in advance for any help I can get! I have recently installed a new western digital WD1600BEVE into my powerbook G4 DVI 12in with no luck. I have taken it apart twice, uggh, and put it back together once with the old Toshiba drive and once with the WD drive, both with no luck. Neither drive shows up in disk utility, only the dvd which i have booted off of. Goes for the same when I boot off of my firewire external. It's driving me crazy. The new WD is an ATA-66 I believe and the old drive is a ultra/ATA-100. I don't know much about computers obviously but is the new WD drive compatiable with my computer? If so, where should i go from here, being that I don't want to spend $120 an hour to get it looked at, ha! Could it be a ribbon cable? I'm reluctant to take it apart because A. it's a huge pain in the ***, and B. I don't simply don't think it's a good idea to keep taking it apart. Any help would be very very very much appreciated. Thanks
H

csheen1013:
Welcome to Apple Discussions.
The scenario mentioned by a brody results in the BootROM seeing only 128 GB of the HDD so that anything on the part of the drive beyond the first 128 GB will not be seen. If your computer is in that category you will need to partition your HDD so that the first partition is 128 GB.
However, even if that were the case, it would not account for why you HDD is not being seen by Disk Utility. One possible reason, might be, as you noted, that the ribbon cable is damaged. Other possibilities are a possible logic board problem of the IDE Controller not seeing he drive or the drive itself being defective.
As much as you hate to do it, I suggest that you take a look again. Be sure that the HDD is correctly oriented with the label side up, that the ribbon cable is properly and securely attached both to the drive and on the logic board. Next, I would check the HDDs themselves by placing them, one at a time, in a firewire enclosure and connecting each one to the computer in turn. If Disk Utility sees the drive, the issue is not the drive, but elsewhere. You can try a different cable if you can locate one. If the issue is on the logic board, there is not much you can do. Your option, in that case, would be to install the drive in a 2.5" firewire enclosure and use it as a portable firewire HDD.
cornelius

HT4759 I had to change my apple password to fix hard drive problem in my iPhone and now I cannot connect date stored in iCloud as my password has changed. How do I plug in new password to iCloud to be able to retrieve data from my MacBook Pro to my I pho

If you change your apple password how do you notifly icloud to resync everything? Forgot my apple password, had to change it due to hard drive problem on my iphone 4 which had to be totally erased then rebouted and now works but cannot download from my computer/icloud due to password change. So how do I orchestrate the change of password to icloud/computer to allow all to sync together?

If you use Lion, boot into your recovery pressing Command and R buttons, press "Utilities" menu, open Terminal and write:
resetpassword
If you have Snow Leopard, boot into your install DVD pressing C button, click "Utilities" and press Password Reset

Help! folder icon w/ exclamation point - hard drive problem?

I live in the philippines and the store which i called up said the only solution is to show the receipt and they will send it to singapore but i still have to buy a new one. it's like they're not giving me choices at all. i know my iPod is not yet "dead", why do i have to buy a new one? how can i have this repaired?! it hasn't been a year yet, but around 10 months already and i don't have the receipt anymore.
here's what happened...
for the past week my iPod has been skipping songs, going to the next ones but doesn't play at all. sometimes it even freezes. and i hear this whirring sound at the back.
so i decided to connect it to the computer and erase all my songs first coz i thought maybe the problem was with the files. but iTunes didn't recognize the device. so i decided to reset it (so that the songs and my factory settings will be erased) by pressing menu and select at the same time. then after i did this the "do not disconnect" message kept on showing up and eventually it just stayed there. so i tried resetting again. the apple logo shows up but after a while the folder icon with exclamation point shows up. then it would turn off.
I tried restoring it with updater but it says it could not mount the ipod. so this might be a hard drive problem already. how can i solve this?
please help!

Try calling their toll free number <probably charges apply when you're calling outside the US>, 1-800-827-0685.
Usually, they will send your machine to the nearest repair station. I think in SEAsia, repair stations are in Malaysia.
Your iPod comes with a universal warranty, so you could definitely have that repaired even without the receipt. <Im from the Philippines too. I what you mean...>
good luck!=D

Hard drive problem...... Please Help

Hard drive problems
I am sure it is due to my error or mistake but I received a new Maxtor III touch as a replacement for my failed drive yesterday after connecting it I went to Maxtor one touch manager software that came with it and the drive did not appear in the window so then I opened disk utilities and copied my notebook hard drive over to the Maxtor ran permissions on each drive and then closed down my system ! today when I opened my Powerbook with the Maxtor on it gave me the grey screen 2x so I disconnected the Maxtor ran permissions again and everything was fine until i power up the Maxtor and Grey screen again! Help How do I fix this?????

Maxtor one touch III firewire 800 its connected to my Titanium G$ Powerbook I am beginning to think its just another drive failure

I have been storing my Aperture and IMovie Libraries on an external hard drive that recently died. Fortunately I've been using Time Machine to back up to a 2nd external drive. How do I restore my libraries to a new external hard drive?

I have been storing my Aperture and IMovie Libraries on an external hard drive that recently died. Fortunately I've been using Time Machine to back up to a 2nd external drive. How do I restore my libraries to a new external hard drive?

This is a tricky one.
Open up Time Machine and go back to a date using the timeline on the right side of the window when you know the drive was working and was backing up as part of Time Machine backups.
Click on the name of your Mac under the Devices heading on the left side of the window in Time Machine, and if things are working correctly you will see Macintosh HD (or whatever you have named it) and the name of the external hard drive that was backing up in the past.
Right-Click on the name of the external hard drive and then click on "Restore (name of drive) to....." You may be asked for your adminstrator password at this point.
It might be easier to restore the drive contents to your desktop if you have room on your Mac, and then copy things over to the new external drive where you want to store the Aperture and iMovie Libraries.
Once the libraries have been moved over the new external hard drive, you will likely need to "point" Aperture and iMovie to the location of the libraries on the new external hard drive.

How do I transfer an existing Aperture library to a new external hard drive

I have a new external hard drive where I want to store my pictures to free up room on my iMac
How do I take an existing Aperture library and move it to the external hard drive so that Aperature can find and use it? Once it is moved can I delete the library from my iMac without causing problems with my new hard drive library?
thanks

Hello Barty,
is your library referenced or managed?
If your Aperture Library is managed, then you can simply copy it to your new external drive using the Finder. Make a backup of your old library and convince yourself that the backup is working.
If your library is referenced, then use Aperture to relocate your master image files to the external drive (select all images, then File -> Relocate Master), then copy your Library to the external drive using the Finder.
To point Aperture to the new library location, double click the new Aperture Library to open Aperture with it. Test it thoroughly, before you delete the original library.
You might consider only to relocate the master images to your external drive and to leave the then much smaller Aperure Library on your system drive. That way Aperture will work faster, and you will be able to browse and share your images, even when our external drive is not connected.
Regards
Léonie

PLEASE HELP .... Tosiba hard drive problem or dead ???

Hi ... I never had a hard drive die before. So I am not sure how this would occur. Not sure if I purchase a new Toshiba hard drive would solved the problems I am coming across.
I am using a Toshiba MX4019GAX 40GB h/d for my notebook for about 5 1/2 years.
Error Message#1:
Intel(R) Boot Agent FE v4.1.09
   (c) 1997-2002, Intel Corporation
   Intel Base-Code, PXE-2.1 (build083)
   (c) 1997-2002, Intel Corporation
   PXE-E61: Media test failure, check cable
   PXE-M0F: Existing Intel Boot Agent
   Operating System Not Found
This is partially solved. But comes back after a couple of crashes and sometime when I turn on the notebook.
After selecting F10 for BIOS boot setup, hard drive is listed as first selection. The "Primary Master" shows "none" every now and then. Sometimes it will pick up and list the Toshiba hard drive. I did see the Toshiba drive listed with garbage (!!!! after Toshiba MX4019GAX) a couple of times. Already opened the HDD drive bay and checked connections/tighten cable. Looks okay to me.
Problem #2: Notebook crashes while I'm on the internet.
Error: States a serious error has occurred and the system will shutdown
to prevent serious damage (the dreaded blue screen).
After restarting the notebook. I get ..... Cannot find file .... c:/windows/system32/config ....
So I reinstalled the prepackaged windows xp os through setup along with drivers and application programs. It worked for a while and then crashes again. I reinstalled again, then I get the error ....
Problem#3:
Error: Faulty driver discovered by plug and play.
Blue Screen tech info: Setup: 0x000000CA (0x00000001, 0x812c5B10, 0x812c5E30, 0,x000000000)
Now I cannot even get to windows. I also disable plug and play through the BIOS
setup. I still cannot get to windows.
Problem#4 While going through Windows setup ........
Error: Windows XP require a hard drive volume with at least 492 megabytes of free space ....... Setup was unable to locate such a drive with the required amount of free space.
I just get a blinking cursor on a black screen now.
IS THE PROBLEM THE HARD DRIVE?
I did not hear any rattling or loud noises like most users do.
Question #1: How do users usually know a hard drive is dead?
Question #2: What occurances tells a user that a hard drive needs to be replaced (what do the see happen on the screen)?
Question #3: Are users coming across the same problems I am having (are these the signs)?
Question #4: Checking the C:\ with DOS .... why don't the full 40GB show. Only see a 100,000+ bytes listed.
Please advise. Any help would be greatly appreciated.

Everything you are seeing is indicative of a failing hard drive. Ensure that you have backups of any critical data immediately before it fails completely. Then replace the drive.

Time Machine incomplete backup on new External Hard Drive

I have a LaCie 2TB firewire external hard drive I bought 2 years ago. I made 3 partitions, one called "Time Machine" for TM backups of my iMac HD, one called "Video" for video files, and one called "HD2" that I used to install new programs and store edited photos and img files. I ran TM onto this HD for the last 2 yrs with no problems. I recently decided that I needed to have a backup of my iMac HD --- AND the 2 partitions (Video and HD2) on my LaCie. So I bought a Seagate 2TB external USB HD that I planned to use ONLY for Time Machine.
So I hooked it up and formatted it (no partitions), then went to TM options and selected the new Seagate Hard Drive to backup to, and in the options I excluded the Seagate (by default) and the Time Machine partition on my LaCie. Nothing else was excluded. In other words, I wanted to backup my entire iMac HD, and my Lacie Video and HD2 partitions.
My internal iMac HD has 116 GB used, my Lacie Video partition has 355 GB used, and my Lacie HD2 partition has 175 GB used. So I was expecting the Seagate to backup 646 GB.
When my Time Machine backup started at 1 AM, I was happy to see that the status box showed "Backing up 1 GB of 646 GB." When I woke up at 8 AM, I was happy to see that the status box showed
"Backing up 536 GB of 646 GB."
But it stayed stuck on 536 GB until 12 Noon, then started slowly working again. By 7 PM, the status showed "Backing up 623 GB of 646 GB." Then at 8 PM, the status box disappeared and it seemed like everything was backed up. But my Seagate HD shows only 629 GB of used space. So I decided to check the backup in Finder to see what went wrong.
In the Seagate backups folder, I have three folders - one named "Macintosh HD" which shows 112 GB on disk, one named "Video" with 341 GB on disk, and one named "HD2" with 175 GB on disk.
So it appears that my iMac HD was only backed up 112 GB out of 116GB, my Video partition was only backed up 341 GB out of 355 GB, but my HD2 partition backed up the entire 175 GB out of 175 GB.
So my question is - is this normal, or is my backup really missing 4 GB of files from my iMac hard drive and 14 GB of files from my video partition? I started to look at them file by file to see if they matched, but there are so many files, so I thought I would ask in case any of you might have heard of this before. If your answer is that my backups are corrupt or incomplete, should I reformat the Seagate and start over?
Also, is it safe for me to manually delete all the files in my time Machine partition on my LaCie hard drive, since I won't be using that anymore for Time Machine backups? Or is there a process I must follow to delete those older backups?
Thanks for reading this far and for any advice you can shoot my way.

Thank you for your well thought out response. It was really helpful by showing me where to look at things more closely.
Time Machine automatically excludes some things that aren't necessary for a restore, such as system work files, most caches and logs, and trash.
This is good to know. Although I didn't have anything in the trash, I have no idea how much is in the various caches and logs. I'd be surprised if they totaled 4GB, though. I'm still worried about this backup, as explained below after doing a Console log check.
If any files were open, they may not have been backed-up (a partial file wouldn't be of much use). I don't know of any special exclusions for video files or apps, but there may be some. You might want to try the Terminal command in the yellow box of #11.
I didn't have anything else running except TM, so no files were open. I checked the exclusions in the yellow box #11, the Terminal Command, and /System/Library/CoreServices/backupd.bundle/Contents/Resources/StdExclusions.pl ist, but nothing seemed to point to the video files I have saved. So I'm still at a loss with this part of the backup.
You might want to look at the log of that backup
I looked at the log - thank you for the link on how to see it - but the entries show that the size of the backup was even less than I thought - It seems I am actually missing 0.2 GB from the HD2 partition, 6 GB from the iMac HD, and 14.4 GB from the Video partition. And since it shows the exclusion amounts, I'm really at a loss for the iMac HD now. Here's what the Console listed for this backup:
Aug 29 00:55:54 paul-imac-5 /System/Library/CoreServices/backupd[567]: Backup content size: 174.7 GB excluded items size: 0 bytes for volume HD2
Aug 29 00:55:54 paul-imac-5 /System/Library/CoreServices/backupd[567]: Backup content size: 355.7 GB excluded items size: 0 bytes for volume Video
Aug 29 00:55:54 paul-imac-5 /System/Library/CoreServices/backupd[567]: Backup content size: 116.3 GB excluded items size: 30.5 MB for volume Macintosh HD
Aug 29 00:55:54 paul-imac-5 /System/Library/CoreServices/backupd[567]: No pre-backup thinning needed: 776.02 GB requested (including padding), 1.82 TB available
Aug 29 00:55:54 paul-imac-5 /System/Library/CoreServices/backupd[567]: Waiting for index to be ready (909 > 0)
Aug 29 02:37:30 paul-imac-5 /System/Library/CoreServices/backupd[567]: Copied 3275 files (174.5 GB) from volume HD2.
Aug 29 05:49:40 paul-imac-5 /System/Library/CoreServices/backupd[567]: Copied 5412 files (515.9 GB) from volume Video.
Aug 29 19:18:46 paul-imac-5 /System/Library/CoreServices/backupd[567]: Copied 146976 files (626.2 GB) from volume Macintosh HD.
Is it possible to see how many files are in each drive that I was backing up? If I could match the file count, it might give me a better idea. I used Finder, but it only gives me the GB Capacity, Used and Free. For example, if I could see if the LaCie Video partition has exactly 5412 files (or 2137, if the file count above is a running total), I will believe that all the files backed up but may have been truncated. If the partition shows more than 5412 files, then I'll know that not all files were backed up. So at least I can start looking manually.
It will be much faster and easier to erase the partition with Disk Utility.
Thank you for this advice. This should save lots of time. I won't erase my other partitions when I do this, right? Also, will it leave a blank partition there so I regain my space?
I'm really bummed out by this backup. I haven't used my iMac for anything except Safari since this happened, because I do not want to start working again until I know that I have a safe backup, and I don't want to make any new files until I can resolve this. I thought of just reformatting the Seagate and starting over, but I have a feeling it may do the same thing. So at this point, I don't know if the Seagate is faulty, if the TM is not working properly, if I am making a dumb user error, or if this is perfectly normal. The worst thing that could happen is that my iMac HD or Lacie HD fails and I try to restore from my Seagate TM backup, only to find out that my TM backup is incomplete or corrupt.
So I really do appreciate your help and any additional insight you or anyone else might have. Thanks.

HT1391 I had all of my music on an external hard drive that failed. I have iTunes Match so all of my music was synced with the "cloud". How do I now download and save all of my music back down on a new external hard drive?

I had all of my music on an external hard drive that crashed. I have iTunes Match so all of my music was synced in the cloud. How do I now re-load my music back down onto a new external hard drive?

Hey Rbe58!
I believe this question can be answered by the information in the following article:
iTunes 11 for Windows: Access all your music anytime, anywhere with iTunes Match
http://support.apple.com/kb/ph12492
Play or download songs from iCloud
You can play songs directly from iCloud, or you can download songs so you can play them when you’re not connected to the Internet.
If a song is available in iCloud, it has a Download button next to it.
To play the song, double-click it.
To download the song, click the Download button.
After you download a song to a computer, it remains in the computer’s iTunes library, even if you turn off iTunes Match.
To only display downloaded songs in your iTunes library, choose View > Hide Music in the Cloud. This also hides any previous iTunes Store purchases you haven’t downloaded.
For information about downloading and playing songs on an iOS device, see the documentation for the device.
Thanks for using the Apple Support Communities!
Cheers,
Braden

Installing Leopard and new internal hard drive at same time, best plan?

Ok so basically the title explains what I need to do. I am currently travelling in Europe, and returning home to New York on Tuesday night. I have a new hitachi 250gb HD and will have Leopard waiting for me at home when I arrive, and will get right to doing this installation. I am writing on the discussion boards here because I am hoping the users here can give me their opinions on what is the best plan of action to do this whole install?
So what I was thinking was, I should remove the hard drive that's already inside, put it into an external enclosure. Then, put my new blank 250gb hard drive into the macbook pro, close up the computer, then put the Leopard OSX install disk, and do a completely fresh install of Leopard. Then, after installing (or during installing?) I should run the migration assistant program to get all my files and settings etc. transferred over to the new internal hard drive with Leopard on it, from the old hard drive that will be plugged in from an enclosure as an external drive.
Will this plan have any problems that I am not aware of? Is there a better process for doing this task? Any advice will be greatly appreciated! I am anxious to get my new hard drive into the computer because my 160gb is filling up, and dying so badly to use the new Leopard!!

You could also put the new disk in the external enclosure, partition it using disk utility. Then make a clone of your current hard disk to the new external one using the restore feature in disk utility. Boot from the external disk and Install Leopard as an upgrade keeping all your files and setting. check everything is all running how I should and swap drives over. That's another option for you.

I have lost my info for my ipod due to hard drive problem. Can I upload the info on my ipod to my computer. I don't want to lose what is on my ipod.

Lost ipod info on computer due to hard drive problem. Can I upload info on ipod back to my computer and how do i do it.

- Transfer iTunes purchases by:
iTunes Store: Transferring purchases from your iPhone, iPad, or iPod to a computer
- Transfer othe music by using a third-party program like one of those discussed here:
Best iPod to PC
- Create a backup of the iPod by connecting the iPod to the computer. Right click on the iPod under Devices in iTunes and select Back Up.
- Restore the iPod from thzt backup and sync a necessary.

I need a new external hard drive for my iMac8,1

I need a new external hard drive for my :
Model Name:    iMac
Model Identifier:    iMac8,1
Processor Name:    Intel Core 2 Duo
Processor Speed:    3.06 GHz
Number Of Processors:    1
Total Number Of Cores:    2
L2 Cache:    6 MB
Memory:    4 GB
Bus Speed:    1.07 GHz
Boot ROM Version:    IM81.00C1.B00
SMC Version (system):    1.30f1
Serial Number (system):    YD8520CD0N4
Hardware UUID:    073B29AD-6FFB-5E64-A52C-BF19A054F363
I do not have Thunderbolt on this and when I look up the specs for USB I get
USB Bus:
Host Controller Location:    Built-in USB
Host Controller Driver:    AppleUSBUHCI
PCI Device ID:    0x2835
PCI Revision ID:    0x0004
PCI Vendor ID:    0x8086
Bus Number:    0x3a
Don't know if this is USB 3.0 or USB 2.0
All the new drives seem to use either Thunderbolt or USB 3.0

I have a Western Digital 2 Terabyte USB External Hard Drive and it works like a charm and it costed me $129.00. My opinion is you can't go wrong with this brand and size for home use.
Cheers
Don

New SCSI hard drive problem: Device busy too long

Similar Messages

Maybe you are looking for