New server in my network list replacing my server

Recently a new unprotected server appeared in my home server list which I noted my iPad was trying to use instead of my regular home one it always uses.
On the ipad I went to Settings and selected this server, pressed blue arrow on right to get more info and saw Forget this server" which I pressed, but the sever persists in my fairly long list being in an apartment building.
This morning I was connected to the rogue server again.
Is there a way to permanently delete it and block any of my devices from using it?

Good morning.. Oh.. so turn it back on. Got it.
My evidence is that I couldn't get to any websites on my iPad. I checked Settings and saw it was connected to the unprotected one. Which I realize now is problably my fault.
A week ago when I first noticed the server, I dumbly, I clicked it just to see if it worked. I have a 30Mbps account and have no interest in stealing someone's connection.
I'm thinking that my network must have crashed and then the iPad chose the other network.
So hopefully "forgetting it" will end this. I can test by powering down my modem and see if it selects the other again.

Similar Messages

How do I best integrate existing laptops for a new server? Can I use the existing home folders on the laptops and make them into Network Users?

How do I best integrate existing laptops for a new server? Can I use the existing home folders on the laptops and make them into Network Users?

Yes it will work. I've done it for a few users in my small office. As with anything, there are quirks that you may or may not experience. Most quirks are app-related, due to app developers hard-coding absolute paths into their apps for things like temp files (Photoshop). Strategies for resolving these sorts of quirks can be found via google. You would probably have seen these quirks already when using server-based home folders for your kids. If you haven't noticed them, then you're probably fine.
The tech note you cited should be fine. It doesn't explicitly say so, but you'll need to enable ssh on your server, at least temporarily, so you can upload your home folder to the server using scp, rsync, etc. Don't try to copy the files up to the server via Finder.
Once all your files are transferred to the server and in the right place, make sure to chown them on the server, so they are owned by the userID you created for yourself on the server.
As with anything this involved, make a good backup of your laptop first.
Note I have one user that isn't too happy with the responsiveness of the periodic mobile home syncing. She has about a decade of e-mail in her home folder, probably 50 to 100 emails per day, many with attachments. Mobile home syncing takes a long time to check and sync this huge tree of itty-bitty files, eevn with server-side file tracking turned on. The other users are happy.
The nice thing about mobile home syncing is that when a user "graduates" to an age where they've earned their own laptop, you can change them from a server home user to a mobile home user, with a minimum of fuss. Also, if you lose or break a laptop, you can add a new replacement laptop to your network, and pull-down a replica of the home folder from the server, with almost no downtime.

"Unable to load network list" on new sim card overseas on unlocked iphone 4

I recently bought an Iphone4 (unlocked) from australia. While traveling overseas I inserted a new sim and got the message "unable to load network list", and could not activate my new sim card. Could not find the answer on the discussion board here but got in touch with my provider back in oz who helped me.
Solution: You need your laptop with Itunes on it. Turn the phone off, then connect to your laptop with Itunes already running and then turn the phone on. When you click on your phone icon in Itunes it will say "Congratulation, your iphone is unlocked". You can then eject your phone and your new sim is activated.
Hope this helps

Sorry not sure why your new sim card isn't supported...not sure if it helps but I had my laptop connected to wifi at the time also, but I don't think it should matter. Its worth a try connecting to internet with ITunes on, connect your phone and then turn it on and see what happens.

Replacing Exchange 2007 with another server with new server name

I am working with a client to move Exchange from the server it is on now to another server. This will be new hardware and new name. The current server Exchange is on will still exist by I want to move Exchange completely off of that server.
Current Network Setup:
Server 1: 1 SBS 2003 server is Domain Controller, Runs AD, DNS, DHCP, File Sharing, SharePoint 2003 and Remote Desktop
Server 2: Server 2008 running Exchange 2007, Backup Domain Controller, File Sharing, SharePoint 2007, Terminal Services.
Current Plan:
Introduce Server 3 to run just Exchange 2007. I would like to completely over a short period of time move exchange from Server 2 to Server 3. I have searched over the internet and found several articles but still have a few questions. There are roughly 75
mailboxes with 50 actual users. Some users are using Outlook 2003 that came with the SBS 2003 and others are using Later versions of office. Server 3 will be a Server 2008 R2 system.
1. What is the best method to perform this transfer. I found article TechNet
Article that explains with 2 remote offices how to do this but not sure if the same will apply.
2. Since I am not immediately decommissioning Server 2 how can I safely remove all the roles and add them to Server 3?
3. For the end user impact. Will the change make Outlook automatically pickup the new server name or will each user need to reconfigure their outlook profiles?
4. I will be moving OWA since there are several Remote and Terminal Service users that use OWA for email. I would like to keep the same certificate and domain name setup if possible.

Hi,
According to your description, I recommend you install another exchange 2007 on server 3, the exchange server role as the same as server 2.
And then, transfer all mailboxes and configurations(OWA,DNS..) from server 2 to server 3.
Finally, decommission the server 2 .
Thanks.
Niko Cheng
TechNet Community Support

Replace existing server with new server

Good Day Guys,
Could you please throw some light on the issue below,
Our QAS is down for more than a month and we are having problems with the server on hardware side,so our company has decided to scrap up the old server and bring a new server in its place.
Could you please share your ideas as of how to proceed from having new server.My concerns.
Installing sap and Mssql from scratch naming same as our old server.Here im stuck.......whether to install a new database and do DB refresh from the production database.
Please post me all the activities to considered for a new installation and to have a copy of production installed on it.
thanks in advance,

Hi,
This is how you should proceed.
1. Take a full backup of your production - make sure it is successful.
As you cannot use the sql server detach/attach from production - you will have to do a backup and restore.
2. Uninstall your quality - the uninstall steps are there in the installation guide.
3. Install your QAS using SAPINST as per the homogeneous system copy installation guide. And select the option db using "backup/restore" when SAPINST asks for it.
4. Restore the database using the production backup and logs via the SQL Server Enterprise Manager.
5. You will have to change your schema names by following the sap note 551915 - this is only needed if your SAP system uses the MCOD convention of the form SAP<SID>.
Also, check these SAP Notes 151603, 193816for a SQL Server Copy.
Hope this helps.
Reg, Dibya

Possible to make clients sharepoint alias direct to new server sharepoint?

I'm replacing a Mac OS 10.2 server with a 10.6 server. Ideally, the (approximately 100) client machines' network aliases would, somehow, find the shared folders on the new server. "Somehow" in my mind, would be for the new server to assume the IP of the old one, and if necessary replicate the path to the shared folder(s).
My experimentation tells me this is not possible*, but I don't want to believe it.
Background - I have no DNS on the LAN; the aliases were setup using the 'Connect to Server' command with the (static) IP of the server.
* I renamed the new server, could no longer authenticate to it, and had to erase the HD and re-install and re-setup. hrmph!

It's clean enough, although if I remember correctly you can't bulk upload the data to an external list. If bulk upload isn't available, writing a little script that syncs the data is probably the easiest way to do it, and then delete the old list.
Kind regards,
Margriet Bruggeman
Lois & Clark IT Services
web site: http://www.loisandclark.eu
blog: http://www.sharepointdragons.com

IPad 1 3G in India - Unable to load network list

I am using iPad 1 - 3G in India (Pune) for past a few months. It was working properly using a cropped BSNL 3G sim. Even in roaming I had no issues.
A few days back it first started showing only EDGE instead of 3G and now it has stopped communicating using cellular network. I get the error that "Unable to load network list". WiFi works fine. Now I have upgraded to iOS 4.3.5 (that is after the 3G stopped working).
I was under the impression that iPads are not bound to any cellular provider but there seems to be something that I do not know about Apple devices. I am new to Apple devices and have not used any before this iPad.
Any help will be appreciated.

Hi there,
I had kind of the same thing where i would arrive abroad or back in the UK after being abroad and my iPhone would take 20-30 minutes to get a signal and when loading up network selection would always get unable to display message.
Had phone replaced by apple and the issue hasnt occured in the once ive been abroad since - connected pretty much straight away.
Just wondering if you are having the issue of delayed text messages where people text you and sometimes it takes 30mins-few hours to get delivered to your phone. Or the issue of people sometimes call you and you good signal and it goes straight to voicemail??

HT1937 iPhone 4 display "unable to load network list"

Hi Guys,
I have a iPhone 4 from Singapore and it was working perfectly fine. I came to US few days ago and get a SIM card from T-mobile. My phone can't seems to detect any network with the new SIM card. I went down to T-mobile and they replace a new SIM for me but the problem still persist. The top left corner of the phone display "No service", then I went into Settings>Carrier I tried to turn off the automatic Network selection and a prompt "Unable to load network list" appear, after I select "OK" the automatic setting switch back to ON.
I look around on this site and tried a few recommendation, none work so far. Things I tried:
- Restore to the phone via iTunes and restore back up
- Restore to the phone via iTunes and set up as new phone
- Settings>General>Reset>Reset Network Settings
- Switched off the phone and connect to my laptop with iTunes already running
- With my phone connected to iTunes, I switched it off and on
My wifi connection is fine, and I tested my SIM card in my friend's phone it works fine too.
My phone profiles under About:
- Network: Not available
- Version: 5.1.1 (9B208)
- Carrier: Carrier 12.0
- Modem Firmware: 04.12.01
Anyone can give me advices on how to get my network connection back?
Thank you!
PS: I had never jailbreak my phone before.

I would try reseating the SIM and if that does not work, replace the SIM.

Adding a new server in the menu of SAP GUI 640

Hello Everybody,
While adding a new server to the menu of SAP GUI 640 using Server Tab after entering all details like :
1] SAP System ID
2] Hostname where message server is running
3] SAP ROUTER :None
After filling all the above details and after pressing the Generate List Button I am getting the following error .Please help me to know why this error is coming and suggest a solutio for adding a new server to my SAP GUI 640.But I am able to add a new server using User defined tab but I want to add a new server using Server tab.
Below is error details which I am getting:
Error:service'sapmsSBX'unknown
Wed Jan 09 06:41:13 2008
Release 640
Component NI(network interface),version 37
rc=-3,module ninti.c,line 463
Detail NiPGetServByName: service 'sapmsSBX' not found.
Thanks and Regards,
Ashish Thakkar.

Hi,
check etc/services for sapmsSBX entry. If missing - add it (i.e. sapmsSBX 36XX/tcp - where XX is your instance no.)
Add an extra [Enter] after last line of etc/services.
Regs,
FS

Advice on RAID and backup of new server in CAD office

Hi, I work for an architects firm and we're looking to purchase a new server.
Our current situation:
• Dozen workstations running Leopard, on a gigabit network
• Server running Leopard Server (Standard setup), with one 250GB ATA hard drive (17GB space spare)
• Data files are backed up and taken off site each day with a triple rotation of external hard drives, using Retrospect.
• The server hard drive is cloned to an external drive each week, which stays on site, using SuperDuper.
• User accounts from workstations are all backed up to an external drive, which also stays on site, using Retrospect.
• And I've been trialing Time Machine, backing up the data to an external hard drive, but I can't see this replacing Restrospect backup as Time Machine doesn't compress the files.
To the future:
• What sort of RAID setup should we go for in a new Mac Pro server?
• I'd like to throw it all into performance but I'm thinking we should probably use a RAID to replace our SuperDuper clone from above.
• When you have mirrored drives presumably if one fails the other one just carries on doing all the work by itself?
• Should we run the system on two mirrored drives and the data on the other two? Or if I'm looking for more performance would I be better having 3 mirrored drives for the data and one for the system? Is this even possible?
• Is it possible to get the smaller 73GB SAS drives for the Mac Pros? It seems you can only get the 300GB ones, which are £500 a pop!

Keep in mind that mirrored RAIDs require two similar drives preferably the same make and model. A mirrored RAID only provides drive failure protection, it does not provide data redundancy. If you need a backup then you need two mirrored RAIDs using one to backup the other. This is also true of striped RAIDs which only provide increased storage but provide no protection against drive failure nor provide data redundancy.
These factors should be taken into account when planning your setup.
Personally, I would not recommend using Time Machine. Aside from being fairly basic as a backup utility it is not sufficiently reliable in my opinion for your situation. Retrospect is a much better choice.

Installing new server - moving windows machines

I have purchased a new Intel Xserve which is going to replace our current production G5 system.
Our current machine is running DNS, OD and is a PDC.
I will be building the new machine from new and will transfer all the data from the current to the new machine
I have a good number of Windows users who are connected to the current system and who are using local profiles on their systems.
I have been running some testing prior to the move and have the following questions?
When I move a windows machine from one server to another. The windows machine has to be removed from the PDC of one server and added to the PDC of the new.
The windows machine effectively gets a new system ID from the new server.
This in turn causes me to copy the users windows "profile" and copy it back once the windows system has been joined to the new PDC.
How can I avoid doing this?
How can I make the windows machine continue without any changes and make it think it is still connected to the original server??

Hi
You should be able to do this by editing the records directly in Workgroup Manager. Enable the 'show all tabs and Inspector' option under the WGM Menu. You should now notice a new icon appear by the side of the Computer List, it will look a bit like a bullseye. Select this and select from the list of Records below. You should be able to edit the SID for Users or for the Group that the Users belong to.
Hope this helps, Tony

7.5 SP3 New Server - Runtime Error on Web Page

Hi experts
I have added a new web server to an existing BPC installation.
The environment is load-balanced, 7.5 SP3, built on windows server 2003 SP2, with SQL 2008 SP1
I used the prerequisites:
Xceed v6.5
Antixscript v3
However, when I try to open the /osoft page directly on the new server, I see the error shown at the bottom of this page.
I checked the DLLs against those on the 2 working servers, and they are the same.
I have copied the antixscript dll from system32 to websvr\bin, as I have seen similar problems before and this has resolved it.
Unfortunately, it hasn't worked this time.
I have also checked that I can log my PC (windows 7, IE8) into either of the existing web servers, and they work fine
I have also opened the web site directly on the new server and that works fine (although it offers nothing but Web and Admin, as Excel is not installed)
I really need to get this server up for user testing first thing in the morning (UK time)
Does anyone have any suggestions?
Thanks
ERROR DETAILS:
Server Error in '/OSoft' Application.
Runtime Error
Description: An application error occurred on the server. The current custom error settings for this application prevent the details of the application error from being viewed remotely (for security reasons). It could, however, be viewed by browsers running on the local server machine.
Details: To enable the details of this specific error message to be viewable on remote machines, please create a <customErrors> tag within a "web.config" configuration file located in the root directory of the current web application. This <customErrors> tag should then have its "mode" attribute set to "Off".

<configuration>
    <system.web>
        <customErrors mode="Off"/>
    </system.web>
</configuration>
Notes: The current error page you are seeing can be replaced by a custom error page by modifying the "defaultRedirect" attribute of the application's <customErrors> configuration tag to point to a custom error page URL.

<configuration>
    <system.web>
        <customErrors mode="RemoteOnly" defaultRedirect="mycustompage.htm"/>
    </system.web>
</configuration>

Quick update:
I'm removing BPC and reinstalling, as the issue definitely lies within BPC and/or its associated Web Site.
I know this as I am able to successfully connect from a client PC to to Reporting Services website.
If anyone has any suggestions, now would be a great time to make them known.
Thanks again

"Unable to load network list" instead of "Hello..."

I am using my 3G iPhone for more than 6 months.
Latest OS 2.2.1, and previous versions are causing a lot of headaches when I switching my iPhone upon arrival.
I am travelling a lot in Europe, every day; I have a Company phone, old Nokia 6300 and my private iPhone 3G.
Nokia connects network in one minute (average), but iPhone...
Instead of "Hello" I am getting always "Unable to load network list" when I switching OFF Airplane mode. There is only one button active: "Automatic" mode of network browsing. When "Automatic" is pressed, iPhone searches network for 3 to 5 minutes and lists the networks available in that specific region.
There are no automatic attempts to connect to any of these listed networks, so I need to select one of the listed networks manually, tap it again, and after some minute or two I am getting service...
I was trying different combinations of 3G and Roaming modes, but did not have any success...
All these headaches started when I performed first OS update.
I am not sure the factory OS version (probably 2.0.2) when I bought it, but only that one was free of the Carrier network browsing bugs.
I am becoming tired of tapping and tapping trying to force to connect to network my iPhone… I tried numerous times OS Restore with iTunes, but no help…
I found a topic in forum: http://discussions.apple.com/thread.jspa?threadID=1671274&tstart=270
But his topic has been archived - replies are not allowed, This question is not answered.
Any ideas?- and does anybody have this or similar problem like mine?
Jonas Jonikas
Vilnius,
Lithuania

Hi there,
I had kind of the same thing where i would arrive abroad or back in the UK after being abroad and my iPhone would take 20-30 minutes to get a signal and when loading up network selection would always get unable to display message.
Had phone replaced by apple and the issue hasnt occured in the once ive been abroad since - connected pretty much straight away.
Just wondering if you are having the issue of delayed text messages where people text you and sometimes it takes 30mins-few hours to get delivered to your phone. Or the issue of people sometimes call you and you good signal and it goes straight to voicemail??

IPhone 4 Unable to Load Network List & No SIM Connectivity Problems

Hi,
I have an iPhone 4. It has been working fine. Only recently, the phone goes off network giving an error message saying that the phone has lost the network. When trying to update the carrier list, the message "Unable to Load Network List" pops up. A while later, the phone sometimes gives a message: No SIM.
I tried restoring the phone's original settings and the problem is still there.
Any recommendations?
Thanks

I would try reseating the SIM and if that does not work, replace the SIM.

Help "unable to load network list"?

After updating my iphone 3gs to ios 4.3.3 my phone's cellular serice does'nt work anymore, when I go to Setting>Carrier it say's "Unable to load network list". But anything else works fine.
Please guysss if someone knows how to fix this please let me know..

Sorry not sure why your new sim card isn't supported...not sure if it helps but I had my laptop connected to wifi at the time also, but I don't think it should matter. Its worth a try connecting to internet with ITunes on, connect your phone and then turn it on and see what happens.

New server in my network list replacing my server

Similar Messages

Maybe you are looking for