New SF300-24P 10/100 POE Switch effecting Sybase App

I recently moved my office. I am running a small Network on Windows 8.1. The main program for my Business no longer has tech support. The program uses sybase sql anywhere 9.0 to network. When I moved from one location to another the only thing that changed is that I started using the above 24 port switch. I have a static IP with my Comcast Internet provider too. Now this program no longer works over the network. I can't seem to establish the ASA Sybase connection anymore. Is there anything in this switch that would be preventing this from happening. I have other network programs that are running properly, it's just this one. I have all the sharing on and security through Windows has all been configured. Any help would be greatly appreciated. 

Hi Jose, please upgrade software of the switch to 1.3.5.58 then factory default it. I recommend do not use a back up config, config from scratch. This should resolve that.
-Tom
Please mark answered for helpful posts

Similar Messages

  • I had my Itunes account disabled due to fraud, if i create a new itunes account how can i switch purchases and apps to the new ID?

    i had my Itunes account disabled due to fraud, if i create a new itunes account how can i switch purchases and apps to the new ID?

    Hi ...
    Just be cause the account was disabled (Apple ID) doesn't mean you can't reset the password and have access to your iTunes purchases.
    Use the iforgot link to reset your password > Apple ID: "This Apple ID has been disabled for security reasons" alert appears
    If you have problems resetting, use the email form here >   Apple - Support - iTunes Store - Contact Us
    edited by:  cs

  • VoIp settings for replacing a Cisco 3550 switch with a SF300-24P

    I am adding the SF300-24P to an existing set of switches.  My backbone switch is a 3560.
    The 3550 I am replacing has this config for each port that supports a Shoretel phone
    switchport trunk encapsulation dot1q
    switchport mode trunk
    mls qos trust dscp
    global settings include
    spaning-tree mode pvst
    spanning-tree extend system-id
    spanning-tree vlan 1,200 priority 28762
    vlan internal allocation policy ascending
    all other settings are at default
    Any ideas how to replicate this on this new switch?  I added the Shoretel mac address range (00-10-49) into the Telephone OUI.  The phone gets power, I think it gets a 192.168.6.x address (local subnet), but then it should get an IP 10.6.0.xx on its VLAN - but it doesn't.
    Some configs from the backbone are attached.  I did not need to configure any of this in the 3550.
    Any ideas?
    Fred

    Hi fred,
    The shoretel phone sounds like it is not attaching to tagged  vlan 200 on my switch, the shortel voice vlan as per your screen captures.
    The Voice VLAN should be tagged on my switch so that phones attach to a Voice VLAN and PC's connected on the back of the VoIP phones attach to  the Data Vlan .
    I scoped out, excuse the pun, the shoretel site and have attached a white paper on setting vlans and shoretel.
    They mention setting option 156 on the DHCP server, so the phone can get vendor specific information etc...  But the phones are not attached to the voice vlan , but the untagged data vlan.  You gotta figure how to get the shortel phones to attach to vlan 200, or if you are not daisy chaining PC on the back of the phone, make vlan 200 untagged on these FastEthernet switch ports..
    I have attached my SF300-48P version of my configuration and some configuration screen shots i took along the way.
    Please review carefully that attached shortel document and my screen  shots and a real configuration done on my SF300-48P.  The configuration should be almost identical to your configuration.
    I added vlan 200. and made sure that all ports were in trunk mode, even the Gigabit uplink ports.
    All ports by default are in VLAN1  as you can see below
    I then added all ports as tagged ports to vlan 200 as you can see below.
    For the sake of Spanning tree, I then made all fast ethernet (phone or PC) ports  fastports except for the uplink Gigabit ports.
    If you are not sure what portfast does , here's a little tutorial I grabbed from cisco.com
    Spanning-tree PortFast causes a port to enter the spanning-tree forwarding state immediately, bypassing the listening and learning states. You can use PortFast on switch ports connected to a single workstation or server to allow those devices to connect to the network immediately, instead of waiting for the port to transition from the listening and learning states to the forwarding state.
    Caution PortFast should be used only when connecting a single end station to a switch port. If you enable PortFast on a port connected to another networking device, such as a switch, you can create network loops.
    When the switch powers up, or when a device is connected to a port, the port normally enters the spanning-tree listening state. When the forward delay timer expires, the port enters the learning state. When the forward delay timer expires a second time, the port is transitioned to the forwarding or blocking state.
    When you enable PortFast on a port, the port is immediately and permanently transitioned to the spanning-tree forwarding state.
    Your tasks I guess should be , making sure that vendor specific options for the shoretel phones are included in the DHCP configuration and that you somehow attach the shortel phones (even manually) to vlan 200.
    For some reason this site adds a zip extension to the end of my running configuration.  I used wordpad to look at the file 
    I am using firmware version 1.0.0.27 on my unit and the userid=admin  password i used was admin
    I hope this helps.
    regards Dave

  • Sf300-24P connected to 2960s

    Hi,
    I have a new small business connect SF300-24P switch which I would like to designate to the core of the network since this has 4 gigabit ports and I also have 2 2960 switches which i would like to dedicate as access switched connect to sf300 core via ether/port channel.
    I have enountered unexpected behaviour when configuring LAG with/witout LACP ?
    Has anyone some experience on setting up this type of configuration.
    Many Thanks,
    Shawn

    conf t
    int range gi1/0/x - x
    channel-group 1 mode auto
    Don't know the SG300 if they have a CLI, perhaps it's the same syntax
    On Catalyst:
    sh lacp 1 neighbor
    sh int gi10/x etherchannel
    Enable debug:
    deb etherchannel all
    deb lacp all
    ter mon
    Michael
    Please rate all helpful posts

  • Need help InterVlan Routing on SF300-24P? .

    Hello
    I really need help with Inter vlan routing via Kerio Controll 7.4.1.
    I have several SF300-24P switches (IOS 1.3.0.62) and i have created a several VLAN's.
    Vlans: Vlan 10, 100, 200 and interface vlan 213 (for management).
    I can ping hosts in the same Vlan via this switches. From switch to host, port is in access mode and between switches ports is in Trunk mode
    (also i had a problem here, trunk wasn't working untill i used command: switchport trunk allowed vlan add all).
    Also port is in Trunk mode between KERIO and SW1 (switch). interface is in TRUNK mode from switch's side because i don't know how configure interface TRUNK mode on kerio.
    On kerio i have configed one physical interface with IP - 172.16.0.1 255.255.255.0 and on the same interface i have created
    VLAN 10, VLAN 100 and VLAN 200.
    static IP's for this interfaces:
    10.0.0.1 255.255.255.0 VLAN 10
    192.168.100.1 255.255.255.0 VLAN 100
    192.168.200.1 255.255.255.0 VLAN 200
    On KERIO i have created DHCP Lease for each VLAN, but i cannot get IP's from DHCP. So i assigned static IP's  to computers
    (for example for VLAN100 PC, VLAN 200 PC and so on) but they cannot ping each other when they are in different vlans, so inter vlan routing itsnot working. but with static IP on the PC, i can ping every VLAN's IP address on KERIO.
    so pls tell me how i must configure inter vlan routing on kerio, is it possible?
    or what must i do? where is my mistake? maybe when i put IP on pysical interface?
    here is my configs and pls help and give me config example.
    config-file-header
    SW1
    v1.3.0.62 / R750_NIK_1_3_647_260
    CLI v1.0
    set system mode switch
    file SSD indicator plaintext
    vlan database
    vlan 10,100,200,213
    exit
    voice vlan oui-table add 0001e3 Siemens_AG_phone________
    voice vlan oui-table add 00036b Cisco_phone_____________
    voice vlan oui-table add 00096e Avaya___________________
    voice vlan oui-table add 000fe2 H3C_Aolynk______________
    voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone
    voice vlan oui-table add 00d01e Pingtel_phone___________
    voice vlan oui-table add 00e075 Polycom/Veritel_phone___
    voice vlan oui-table add 00e0bb 3Com_phone______________
    hostname SW1
    username administrator password encrypted 7fc3774d79570c81cda124d5dcf80b8ae0fcdd6c privilege 15
    username cisco password encrypted 1defefd1f4a214009775b2c2b6b961a77da384b5 privilege 15
    interface vlan 10
    name Staff
    interface vlan 100
    name Cards
    interface vlan 200
    name AP's
    interface vlan 213
    name Management
    ip address 172.16.213.1 255.255.255.0
    no ip address dhcp
    interface fastethernet1
    description MANAGEMENT-VLAN
    spanning-tree disable
    switchport mode access
    switchport access vlan 213
    interface fastethernet2
    spanning-tree disable
    switchport mode general
    switchport general acceptable-frame-type untagged-only
    interface fastethernet3
    spanning-tree disable
    switchport mode general
    switchport general acceptable-frame-type untagged-only
    interface fastethernet4
    spanning-tree disable
    switchport mode access
    switchport access vlan 200
    interface fastethernet5
    spanning-tree disable
    switchport mode access
    switchport access vlan 200
    interface fastethernet6
    spanning-tree disable
    switchport mode access
    switchport access vlan 100
    interface fastethernet7
    spanning-tree disable
    switchport mode access
    switchport access vlan 100
    interface gigabitethernet1
    description Direction-To-SW2       <--- This port is Trunk, but its not showing here for some reason.
    spanning-tree disable
    interface gigabitethernet2
    description Direction-To-KERIO  <--- This port is Trunk also.   i used: switchport mode trunk on both interfaces
    spanning-tree disable
    exit
    banner login 
    SW1
    config-file-header
    SW2
    v1.3.0.62 / R750_NIK_1_3_647_260
    CLI v1.0
    set system mode switch
    file SSD indicator encrypted
    ssd-control-start
    ssd config
    ssd file passphrase control unrestricted
    no ssd file integrity control
    ssd-control-end cb0a3fdb1f3a1af4e4430033719968c0
    vlan database
    vlan 10,100,200,213
    exit
    voice vlan oui-table add 0001e3 Siemens_AG_phone________
    voice vlan oui-table add 00036b Cisco_phone_____________
    voice vlan oui-table add 00096e Avaya___________________
    voice vlan oui-table add 000fe2 H3C_Aolynk______________
    voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone
    voice vlan oui-table add 00d01e Pingtel_phone___________
    voice vlan oui-table add 00e075 Polycom/Veritel_phone___
    voice vlan oui-table add 00e0bb 3Com_phone______________
    hostname SW2
    username administrator password encrypted 7fc3774d79570c81cda124d5dcf80b8ae0fcdd6c privilege 15
    username cisco password encrypted 1defefd1f4a214009775b2c2b6b961a77da384b5 privilege 15
    interface vlan 10
    name Staff
    interface vlan 100
    name Cards
    interface vlan 200
    name AP's
    interface vlan 213
    name Management
    ip address 172.16.213.2 255.255.255.0
    no ip address dhcp
    interface fastethernet1
    description MANAGEMENT-VLAN
    spanning-tree disable
    switchport mode access
    switchport access vlan 213
    interface fastethernet2
    spanning-tree disable
    switchport mode general
    switchport general acceptable-frame-type untagged-only
    interface fastethernet3
    spanning-tree disable
    switchport mode general
    switchport general acceptable-frame-type untagged-only
    interface fastethernet4
    spanning-tree disable
    switchport mode access
    switchport access vlan 200
    interface fastethernet5
    spanning-tree disable
    switchport mode access
    switchport access vlan 200
    interface fastethernet6
    spanning-tree disable
    switchport mode access
    switchport access vlan 100
    interface fastethernet7
    spanning-tree disable
    switchport mode access
    switchport access vlan 100
    interface fastethernet8
    spanning-tree disable
    switchport mode access
    switchport access vlan 100
    interface gigabitethernet1
    description Direction-To-SW1    <--- This port is Trunk also.   i used: switchport mode trunk
    exit
    banner login 
    SW2
    i have excluded many interfaces because hey have same configs.

    Yes Kerio is capable for routing. i wanted to make InterVlan routing via kerio Ccontroll, but i can't and that's i asked here, i need to know reason.
    I have modified 1 switch to L3, and inter vlan routing its now working (without Kerio) and i hope this switches dont have problem when they are DHCP server also.
    thanx for help. I Hope i didnot have much mistakes in config.

  • TROUBLE with SF300-24P

    Hi
    Actually we have the follow diagrame:
    When put the SF300-24P on the remote node we have troubles with pass the vlan tag from voice and data on the same port but when put on access port to the vlan voice and data the dispositives have the correct funtion.
    someone have something about of this trouble?
    the firmeware actually on the switch es 1.2
    Best Regards

    Hi,
    We follow the procedure as You said Us, and now the CP3905 learned the vlan correctly through CDP.
    This is the Show Run now:
    #sh run
    interface  gi1
    spanning-tree link-type point-to-point
    exit
    vlan database
    vlan 320-322
    exit
    voice vlan oui-table add 0001e3 Siemens_AG_phone________
    voice vlan oui-table add 00036b Cisco_phone_____________
    voice vlan oui-table add 00096e Avaya___________________
    voice vlan oui-table add 000fe2 H3C_Aolynk______________
    voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone
    voice vlan oui-table add 00d01e Pingtel_phone___________
    voice vlan oui-table add 00e075 Polycom/Veritel_phone___
    voice vlan oui-table add 00e0bb 3Com_phone______________
    no lldp run
    interface fastethernet2
    lldp med disable
    exit
    interface vlan 322
    ip address 10.1.208.100 255.255.240.0
    exit
    ip route 0.0.0.0 0.0.0.0 10.1.208.1
    [0mMore: ,  Quit: q or CTRL+Z, One line:
    bonjour interface range vlan 1
    hostname switch06e3d7
    ip ssh server
    no snmp-server server
    ip telnet server
    interface fastethernet2
    macro description "ip_phone_desktop | no_ip_phone_desktop"
    exit
    interface fastethernet3
    macro description "ip_phone_desktop | no_ip_phone_desktop"
    exit
    interface gigabitethernet1
    macro description "switch | no_switch | switch"
    exit
    interface fastethernet2
    no macro auto smartport
    switchport trunk allowed vlan add 321
    switchport trunk native vlan 320
    exit
    interface gigabitethernet1
    !next command is internal.
    macro auto smartport dynamic_type switch
    [0mMore: ,  Quit: q or CTRL+Z, One line:
    switchport trunk allowed vlan add 320-322
    exit
    Thanks for Your support
    Best Regards,
    AJ

  • SF300-24P VLAN Confusion - autosmartport not being too smart?

    Hi Everyone, first question i've posted, i'll try and give as much information as possible, i'm an extremely quick learner as well and have been around networking for nearly 20 years but this is my first outing into the medium sized VoIP deployment with prioritised LAN traffic and a client that is itching to say "told you so" about using IP phones.
    I have 4 x SF300-24P switches in a network i'm deploying, 1 will be adjacent to the router (a draytek Vigor 3200 - 4xWAN Gigabit) and the other 3 will be trunked using the GE/01-GE/03 ports to the main switch and will then distribute through a patch panel to give me 96 network ports with PoE capability where required.  There will be 30+ IP Phones on the network, all of which are Yealink T38G SIP handsets.
    I want to have two VLAN's - one for regular workstations, and one for IP Phones with the IP Phone VLAN getting high prority for its traffic on the LAN - all documentation makes it sound simple but it doesn't seem to be working the way I think I expect it to.  I don't mind the two VLAN's sharing the same IP address space at this time and currently all occupy 10.0.0.0/24 internally.
    So, I have 2 questions and a problem.
    First, from the factory, the switches are configured that VLAN1 is the default VLAN and that auto-voice VLAN is also VLAN1?  Is this right?
    Second, i'm having trouble determining the difference in terminology for port types between general, access, trunk etc - obviously trunk is between switches and carries VLAN information through to the next segment of the network.
    My main problem seems to be with auto-voice VLAN and smartport.  If I enable smartport, the switch figures out through LLDP that the port is used by an IP Phone + Desktop (excellent, this is what I want it to do) so then puts the handsets in VLAN1 but then the handsets start to become invisible on the network after 2-3 minutes, the handsets then reboot because they've detected a network drop out and then reconnect, re-register at the voice server and are visible and contactable for 2-3 minutes then the loop begins again.
    If I disable smartport, the problem goes away.
    Am I unreasonably expecting that any user can unpack an IP phone and (subject to provisioning on the server), plug it into any port on the network and it will figure out that it's a phone, not a PC and then prioritise its traffic?
    What I want to avoid is the possibility of internal bandwidth lag if someone copies a large file over the network and people are using the phones that the phone users don't get packet loss or audio instability because of the file copy.  The internet side will be fine, the Vigor3200 has QoS facilities built in and i've had good success on smaller networks with these routers.
    Ideally I need a semi-planned network setup where people with WiFi SIP clients will also get some priority.
    I have set QoS on the handsets to match DSCP46 from the switches - can the traffic be manipulated this way or does it already do that in the DSCP to Queue setup which automatically puts anything above 40 in Queue 4 (high priority).
    All help very greatfully received.
    James

    Hello James,
    Welcome to the forums!
    About the default settings. The switch comes with vlan1 as the default vlan for all traffic.
    Here is a quick overview of the port settings
    access - one vlan
    trunk - multiple vlans
    general - multiple vlans (had additional options)
    When using the auto voice-vlan, you can have your port set as access for vlan 1 and when the switch see a phone connected, it will join the voice vlan also. This allow the ports to be dynamic. It is not necessary to do this. You can create all ports as trunk ports that are part of both your default vlan and your voice vlan.
    The benifits of auto-voice vlan
    -phones are discovered and joined to the vlan dynamically
    -predetermined QoS settings
    -security in that you can have your port set to access
    This is a relatively basic overview.
    As for the problem you are seeing. I would recommend that you check the firmware of the switch and upgrade if needed. While it may not have anything to do with the problem at hand, it will help prevent any future issues.
    I would suggest disabling the Green Ethernet, which can be found under the port management section. If you continue to see the problem after that, I would recommend giving us a call at the support center. We will be able to look a little closer to what is happening.
    http://www.cisco.com/en/US/support/tsd_cisco_small_business_support_center_contacts.html

  • 2960S PoE switch into a non-PoE stack

    I have two 2960 Stacks
    Stack # 1 is a PoE stack with two WS-C2960S-48FPD-L with TenGig uplinks running c2960s-universalk9-mz.152-1.E.bin.
    Stack #2 is Non PoE stack with three WS-C2960S-48TS-L running c2960s-universalk9-mz.150-2.SE2.bin.
    I need to add an WS-C2960S-24PS-L for additional PoE port capacity. If I add it to Stack #1 I will have three switches in both stacks, and all PoE switches will be part of the same stack. I am just wondering If I can have disparate switch models in the same stack running the same IOS? If I add the new WS-C2960S-24PS-L to Stack #2 I will end up making this stack a 4 switch stack with three non-PoE switches and one PoE switch. If I add the PoE switch to this stack will I have access to the PoE capabilities of that one switch. Again with the question can I have disparate switch models in the same stack running the same IOS?

    I am just wondering If I can have disparate switch models in the same stack running the same IOS
    Yes.  You can have a different models of 2960S in a single stack.  The main important thing is all members of the stack should have the same IOS version.

  • Problem with SF300-24P

    hi I  Have been facing a problem, like when  we are connecting the Aironet LWAPP  indoor  Accesspoint to Cisco SF300-24P Switch, we are getting some error like LOW POWER...means accesspoint not recieving enough  power from POE Switch.
    As per Cisco Datasheet for 300 series Switch the model number is  SF300-24P and power dedicated to POE is 180 W and all 24ports do support POE at 7.5Wand 12 portsSupport Maximum Power at 15.0W.Required  Power for Aironet Accesspoint through POE Switch maximum is 12.4W is Enough.So can anyone please suggest what to do now.

    Hi Nenad, if you administratively remove auto smart port, auto voice vlan will also be shut down.
    Your original post consists of some important details-
    IP phones are directly connected on the switch and PC's are connected on  the phone, so the PC's get IP's through the phone. FE ports are  configured vlan 10 untagged vlan 20 tagged.
    This is expected and good
    Some PC's can't get IP's,for  example client turn the computer on and can't get IP, sometimes  ipconfig /release, ipconfig /renew on cmd helps sometimes I just unplug  network cable from pc and plug it again and it works, I tried to replace  the IP phone i didn't help.
    When this happens, it usually indicates a convergence issue with spanning tree. If portfast (edge port) does not negotiate, the port will progress through the spanning-tree states, listening, learning forwarding, which can make a long time to receive DHCP / LAN connectivity.
    Sometimes that issue change configuration  on switch port for example client announce that he have a problem, I  connect to switch via the web and see that port on witch is client  connected have configuration vlan 10 data tagged vlan 20 voice tagged  instead of vlan 10 untagged vlan 20 tagged...very strange.
    This statement indicates a macro issue. The macro detects connection types through LLDP and CDP advertisements. If the switch is dynamically assigning vlan id or vlan tag, it means the macro is writing that configuration. Most likely, you will need to go to the macro and re-write the macro to show the native vlan to be 10.
    So, I would recommend to do this- Go to the smart port built-in macro, edit all of the macro like this example
    -Tom
    Please rate helpful posts

  • HT5621 When I got my new iPhone and was trying to switch everything over I accidentally set up a new icloud account with one email and had one on my old iphone with another account. Does anyone know how I can merge the two accounts?

    When I got my new iPhone and was trying to switch everything over I accidentally set up a new icloud account with one email and had one on my old iphone with another account. Does anyone know how I can merge the two accounts?

    You cannot merge Apple IDs but you can go to Settings > iCloud and 'Delete Account'.  When prompted to turn off documents and data, choose the only option which is Delete from my iPhone, but on the other prompt for Contacts, Calendars, etc you can choose 'Keep on my iPhone'  Then once the Account is Deleted form the iPhone, log back in with the correct Apple ID and choose Merge when prompted.  This will merge your data from this iPhone with that iCloud account effectively putting your devices on the same account.

  • RADIUS authentication SF300-24P

    RADIUS authentication SF300-24P
    We have just purchased 20x SF300-24P switches to be installed at our remote offices and we are unable to get RADIUS authentication to work. We already use RADIUS on all our primary network CISCO switches (e.g. 4506s¸ 3560s, 3750s, AP1231Gs,etc) and these work fine so we know the RADIUS server is working.
    We are trying to use RADIUS authentication to gain management access onto these switches. Quite simply although we can see that the RADIUS server is accepting the username and password being sent, however the switch says “authentication failed” when to receives the response. We are using Microsoft NPS RADIUS Clients for authentication purposes.
    We have upgrade the switches to the latest firmware 1.1.2.0, via the console it seems to have a very cut down IOS version so we cannot use the typical CISCO command set to configure the RADIUS as we normally would. Looking at the web GUI there seems to be a number of options missing including the Accounting port. When debugging is switch on there is no indication to say that any of the settings have been misconfigured.
    Any advice you could offer would be gratefully received.
    Mike Lewis

    Here is the documentation excerpt-
    For the RADIUS server to grant access to the web-based switch configuration
    utility, the RADIUS server must return cisco-avpair = shell:priv-lvl=15.
    User authentication occurs in the order that the authentication methods are
    selected. If the first authentication method is not available, the next selected
    method is used. For example, if the selected authentication methods are RADIUS
    and Local, and all configured RADIUS servers are queried in priority order and do
    not reply, the user is authenticated locally.
    If an authentication method fails or the user has insufficient privilege level, the user
    is denied access to the switch. In other words, if authentication fails at an
    authentication method, the switch stops the authentication attempt; it does not
    continue and does not attempt to use the next authentication method.
    Of course the point of interest here is the second paragraph. The initial wording is the behavior you want. The second portion is very open for interpretation (I do agree it is somewhat ambiguous but consistent with the switch behavior). When I read the example and it says the Radius is busy or not responding then you will authenticate locally. Which seems fair enough. But what it doesn't say, is if you can use one or the other, but instead it seems based on preference failure.
    -Tom
    Please rate helpful posts

  • Need to access settings of SF300-24p

    Hi I was just recently hired in my company, we have an sf300-24p switch but I cant find the console cable for it, I think it needs a female to female db9 serial cable, all I have is  a DB9 serial to rj45 console cable for the 2801 router, also I cant find the IP address of the sf300 switch, it is directly connected to the 2801 router, I issued a show arp to the router but didnt find the switch's IP add for web access, to sum it up I have no way of configuring the switch, is there any way to find the IP address of the switch? It also dosnt show on show cdp neighbors, thanks!

    Daniele,
    You would be able to do something similar, password recovery, if you had the serial cable.
    I'll update this post with instructions in a minute. I don't know if this is a project you need to get done today, but it sounds like that serial cable will make your life a heck of a lot simpler. If you can't wait to order one, is there somewhere you can get one locally?
    Best,
    David
    Password recovery steps:
    You'll need a serial connection to the switch with the following serial connections settings (I'm using Putty in the screenshot):
    You will see a prompt during boot right after the cisco logo made out  of #s that says "Autoboot in 2 seconds - press RETURN or Esc. to abort  and enter prom." 
    Hit return, and you will get the following startup menu:
    You'll want  [3] Password Recovery Procedure  and follow the prompts to reset the password without erasing your config file.

  • There is no "Switchport Voice Vlan" command on SF300-24P !!!

    Hello everyone
    I am in an urgent problem :S
    I have a Small Business SF300-24P
    I have created two vlans one data and one voice
    but i have not assigned them to the ports and I am not sure how to do so since there's no "switchport voice vlan" command under the interface !!
    here are the configurations
    btw the switchport mode is still trunk as it is by default
    Thanks in advance
    switch0a1172#
    switch0a1172#
    switch0a1172#sho run
    config-file-header
    switch0a1172
    v1.2.9.44 / R750_NIK_1_2_584_002
    CLI v1.0
    file SSD indicator encrypted
    ssd-control-start
    ssd config
    ssd file passphrase control unrestricted
    no ssd file integrity control
    ssd-control-end cb0a3fdb1f3a1af4e4430033719968c0
    vlan database
    vlan 13,20
    exit
    voice vlan id 20
    voice vlan oui-table add 0001e3 Siemens_AG_phone________
    voice vlan oui-table add 00036b Cisco_phone_____________
    voice vlan oui-table add 00096e Avaya___________________
    voice vlan oui-table add 000fe2 H3C_Aolynk______________
    voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone
    voice vlan oui-table add 00d01e Pingtel_phone___________
    voice vlan oui-table add 00e075 Polycom/Veritel_phone___
    voice vlan oui-table add 00e0bb 3Com_phone______________
    hostname switch0a1172
    username cisco password encrypted c8e383b1dd7be99f878a387d87766e875404e0b3 priv
    lege 15
    ip telnet server
    interface vlan 13
    name "VLAN13"
    interface vlan 20
    name VOICE
    switch0a1172#

    Hi Sandy,
    You need:
    switchxxxxxx(config)# voice vlan id 20
    and smart ports should do the rest.
    for your reference: http://www.cisco.com/c/dam/en/us/td/docs/switches/lan/csbms/sf30x_sg30x/administration_guide/CLI_300.pdf?mdfid=283019666
    Regards,
    Aleksandra

  • UTP Cable Length for AP connect to POE Switch

    Dear All,
    What is the limitiation on the length of UTP Cable for connect AP to POE Switch.
    Thanks.
    C.K.

    I believe it's consistent with the limits for structured cabling: 100 meters end-to-end, assuming the cabling system is compliant with EIA/TIA sandards.
    Good Luck
    Scott

  • Connecting Rv180w and D-Link 5-Port 10/100/1000 Switch DGS-1005G

    This simple exercise has become a pain. I have a D-Link 5-Port 10/100/1000 Switch DGS-1005G connected to an old (10 years old) linksys 4 port router and it works fine. When I try to connect the switch to my new RV180W it appears dead...no connectivity lights at all. I cannot see an uplink port on the RV180w.....I have tried crossover cable still no joy. Am I missing something?

    Hi Tom,
    Yes i am pretty sure, i have called 3S vision and confirmed it, also i conducted 3 test in 3 different switches last week and the camera worked just like that " Plug & Play ".
    I have tested out 3 switches and they are :
    Cisco Switch 16 Port 10/100
    Netgear 8 port 10/100
    Cisco Switch 8 Port 10/100
    I was able to view the camera and modify the settings, upgrade the firmware, etc. all worked, except this model !!!!
    I am losing hope on this and we are considering buying another switch which would be a waste of money.
    Is there is any possible way to enforce the port to read it?
    Also i have noticed one thing, whenver i plug the Camera to SG300-28P switch, the camera has a small led in the motherboard which keeps blinking red when its connected. It is like its trying to boot but not able too.
    I have until the end of the week, if this issue is not sorted out with this switch model, i will have to buy another one

Maybe you are looking for