New System Cause of Stress lol

Hi Everyone
I have read through these and many other forums, but have not found a fix for my issues as of yet.
Here is my history with this pc. About 2 months ago I bought everything listed in my sig and assembled. From day one, this system had the same problem. Freezing up in any graphic intense games.
It started with BF2, then I tried Everquest, then Everquest 2. All with the same problem. Random freezing, no BSOD, no exact time. Could happen 30 minutes in, or 5 minutes.
Now I've been a tech for many years, and it always seems I can never figure out my own pc. So I did the same troubleshooting steps anyone would do.
First problem was 1 defective piece of ram. It was only running at 333 instead of 400. So I decided to run without it to see if that was the problem. It wasn't. Then I noticed in one crash the sound stayed on, so I figured let's try without the SBAudigy. Still the same. I then tried my buddies Ram. Still nothing. Well then I start thinking video card. So I tried playing with onboard video. Seemed to work. So I thought video card. I then RMA'd my video card, the 7800GTX and FINALLY got it back a few days ago. Still the same problem. While it was gone, I decided to try the onboard video again, and it did crash on me.
Ran memtest386, no problems. Running Prime95 right now, and so far no errors.
So last night I decided to reformat my system and start from scratch without loading anything else but the bare essentials, and a game.
I loaded the following:
Flashed the Bios to 3.8
Windows XP Pro
Nvidia's Forceware 78.01 Video Drivers (I had previously tried 4 different versions)
MSI's ATI System Drivers for RS480/RS482
Disabled the onboard video and audio
Loaded Everquest 2
and Crash
So then I got drastic and ripped out the power supply and replaced it with a known good PSU. Still the same story. Ripped the SB Audigy 2 back out, and tried both sticks of ram seperately. Same thing. unplugged the DVD, and still the same.
The last thing I'm about to try is disabling the network card and putting in another to see if that helps. Other than that I'm lost lol.
Any suggestions would be greatly appreciated.
I will check the temperatures for you all as well. Last time I check CPU was running in the 40s so I know it's cool enough, and it hasn't run with a case on in God knows when lol.
Thank You
EDIT: Swapped the NIC and no change. The CPU temp is at 59 Deg Celcius and the system is at 38 Deg Celcius.

Quote from: philbury on 30-September-05, 01:50:28
Hi -
Have you tried lowering the AGP rate or changing the bios settings for copying video bios to RAM?
Phil
Which setting adjusts copying video bios to ram?

Similar Messages

The installation of the new system caused the heating equipment and also heating the charger that tease your burning it. and only now discovered that the source of this 60w no longer being sold in BRAZIL had to buy a power 85w.

The installation of the new system caused the heating equipment and also warming the bellman who tease her and burning so now discovered that the source of this 60w no longer being sold in BRAZIL had to buy a power 85w.

The installation of the new system caused the heating equipment and also warming the bellman who tease her and burning so now discovered that the source of this 60w no longer being sold in BRAZIL had to buy a power 85w.

Hello there, am new here and very stressed, i have an Imac core i3 which is logging off itself after a few seconds of login, it goes back to the login menu where i put the password. I have tried to repair the os but my pioneer rom is not reading the disk.

Hello there, am new here and very stressed, i have an Imac core i3 which is logging off itself after a few seconds of login, it goes back to the login menu where i put the password. I have tried to repair the os but my pioneer rom is not reading the disk. I press the :c" button on startup but its not picking up the disk in the rom, i have tried to put the disk in an external rom but same answer, am starting to think that my os disk is bad. Please help me.

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of this exercise is to determine whether the problem is caused by third-party system modifications that load automatically at startup or login. Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode* and log in to the account with the problem. The instructions provided by Apple are as follows:
Be sure your Mac is shut down.
Press the power button.
Immediately after you hear the startup tone, hold the Shift key. The Shift key should be held as soon as possible after the startup tone, but not before the tone.
Release the Shift key when you see the gray Apple icon and the progress indicator (looks like a spinning gear).
*Note: If FileVault is enabled under Mac OS X 10.7 or later, or if a firmware password is set, you can’t boot in safe mode.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem(s)?
After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of the test.

New system will not boot up.

I am in the process of building a new system and it will not boot to the post. The power gets to the cpu fan and case fan for about 5 seconds then shguts off. I have to clear cmos to get the same response. Please help, I have pulled everything from the case and tried to boot with just the cpu and memory. Same result.

Quote
Originally posted by FastEddie
The Antec Bug involves their True Power line of psu's and involves a problem with the +5vsb. It's caused quite a few problems with many different boards, from stability issues, to boot issues, to freezing in cmos setup issues. Here's a couple links:
Antec Problems with Neo 2 Platinum
Antec RMA
Read these through.
Would be nice if you guys had different psu's to try.
I recently had the "reboot loop during startup" problem with an Abit AI7 and the Antec TruePower 480. However, the problem didn't start to occur until several months after it was new. After replacing the PS with a 430 amp Enermax the problem went away.

Can't get XP or Win 2K to load on new system

Greetings and Help!
I'm putting together a new system and cannot get XP or 2K to load.
The load begins as normal but about 40% through the file copies, the windows loader starts giving errors that files (on the CD) are 'corrupted' and do I want to try again or skip files (yea...like system32.dll ..... sure I can leave that one out).
I have the system down to KVM. I have tried turbo mode - default mode, hyper-threading on and off. Just about bios option I can try.
I don't know what the bios version is because the board is at home and I am at work (shhhhh). My guess is that it's 1.3 (I bought the board about 2 weeks ago from newegg).
Any ideas or solutions (other than a 357 port in my forehead)?
Thanks

I have had this happen to me in the past when trying to load Win 98. It was caused by the CD ROM having difficulties reading the installation cd which was brand new MS issue. I had to use another cd reader to do the installation. There was nothing wrong with the cd or the original reader, just slight incompatibility. The thing that puzzled me for so long was that the installation would halt at a different point every time with different files being indicated as corrupt. But I also would make sure my memory is securely installed and not faulty and that the CPU is not overheating.

Fine tuning my new system

I have a G4 duel with lots of 3rd party software installed and that has caused all kinds of issues with final cut express HD.
As a result I have just purchased an end of line G5 17" imac at a good discount, it shipped with Panther OSX(10.3.5) Superdrive, 1.8g processor, but alas it only has a 80 gig hard drive. the good news is the company have thrown in an extra gig of ram. and a boxed edition of Tiger.
What would be the best way to set up my new system, the only software i want to use is Final Cut Express, I have the 1.0 version, 1.01 upgrade and the HD upgrade.
1. What system would you use
2. What version of final cut would you load
3. How much of the system do i need to install.
Thanks Mike Hooley.

1. Tiger. I would erase the hard drive and install the OS.
2. FCE3.
3. ???? I usually don't install foreign languages in the OS. Is that what you mean?

SMSY generating runtime error on adding new system

In our solution manager system, while trying to add a new system details
via SMSY transaction we are getting the Runtime Errors
OBJECTS_OBJREF_NOT_ASSIGNED.
Please find the dump details.
Runtime Errors         OBJECTS_OBJREF_NOT_ASSIGNED
Exception              CX_SY_REF_IS_INITIAL
Date and Time          29.05.2008 10:47:54
Short text
    Access via 'NULL' object reference not possible.
What happened?
    Error in the ABAP Application Program
    The current ABAP program "SAPLSMSY_ACTUALIZE_DATA" had to be terminated because
     it has
    come across a statement that unfortunately cannot be executed.
Error analysis
    An exception occurred that is explained in detail below.
    The exception, which is assigned to class 'CX_SY_REF_IS_INITIAL', was not
     caught in
    procedure "UPDATE_HOST_LCR" "(FORM)", nor was it propagated by a RAISING
     clause.
    Since the caller of the procedure could not have anticipated that the
    exception would occur, the current program is terminated.
    The reason for the exception is:
    You attempted to use a 'NULL' object reference (points to 'nothing')
    access a component (variable: "ACCESSOR").
    An object reference must point to an object (an instance of a class)
    before it can be used to access components.
    Either the reference was never set or it was set to 'NULL' using the
    CLEAR statement.
Information on where terminated
    Termination occurred in the ABAP program "SAPLSMSY_ACTUALIZE_DATA" - in
     "UPDATE_HOST_LCR".
    The main program was "SAPLSMSY_MAIN ".
    In the source code you have the termination point in line 2013
    of the (Include) program "LSMSY_ACTUALIZE_DATAF01".
    The termination is caused because exception "CX_SY_REF_IS_INITIAL" occurred in
    procedure "UPDATE_HOST_LCR" "(FORM)", but it was neither handled locally nor
     declared
    in the RAISING clause of its signature.
    The procedure is in program "SAPLSMSY_ACTUALIZE_DATA "; its source code begins
     in line
    1983 of the (Include program "LSMSY_ACTUALIZE_DATAF01 ".
Source Code Extract
Line SourceCde
1983 FORM UPDATE_HOST_LCR USING    IV_HOST STRUCTURE SMSY_HOST.
1984
1985   DATA:
1986         ACCESSOR        TYPE REF TO CL_SLD_ACCESSOR,
1987         VALUE           TYPE STRING,
1988         VALUE1          TYPE STRING,
1989         EX              TYPE REF TO CX_SLD_API_EXCEPTION,
1990         T_INAMES        TYPE SLD_T_STRING,
1991         INSTREF         TYPE REF TO CL_SLD_CIM_INSTANCE,
1992         SYSTREF         TYPE REF TO CL_SLD_CIM_INSTANCE,
1993         CLNTREF         TYPE REF TO CL_SLD_CIM_INSTANCE,
1994         LINKREF         TYPE REF TO CL_SLD_CIM_INSTANCE,
1995         INSTHANDLE      TYPE STRING,
1996         SYSTHANDLE      TYPE STRING,
1997         CLNTHANDLE      TYPE STRING,
1998         LINKHANDLE      TYPE STRING,
1999         T_KEYPROP       TYPE SLD_T_VALUELIST,
2000         I               TYPE I,
2001         PROPLIST        TYPE SLD_T_VALUELIST,
2002         PROPERTY        TYPE SLD_S_VALUELIST,
2003         FILTER          TYPE REF TO CL_SLD_FILTER.
2004
2005   DATA STRING          TYPE STRING.
2006   DATA IV_SYSTEM       TYPE SMSY_SYSTEM_SAP.
2007
2008   GET_SLD_TOP_INFO.
2009
2010 * Test the connection to the SLD server:
2011   TRY.
2012
>>>>>       ACCESSOR->PING( ).
2014
2015     CATCH CX_SLD_API_EXCEPTION INTO EX.
2016       VALUE = EX->GET_TEXT( ).
2017       MSGMACRO 'SCDT_LIS_IF' 'E' 11 'LCR_ERROR'.
2018   ENDTRY.
2019
2020
2021 * Catch all exceptions potentially triggered by the API:
2022   TRY.
2023
2024
2025 *   Create a new instance representation object for class SAP_BCSystem.
2026 *   If an accessor object is supplied in the constructor, the object
2027 *   reference of the representation can be used in other accessor
2028 *   methods.
2029       CREATE OBJECT SYSTREF
2030         EXPORTING
2031           CLASSNAME      = 'SAP_ComputerSystem'
2032           ACCESSOR       = ACCESSOR.
I am already at the latest support package i.e13
Regards
Anthony

Hi Anthony
Is your problem solved . I M facing the same problem . I found another thread which is suggesting to follow SAP note 1042815. But it seems that we need to change Some standard include to get it fixed .
Does SAP suggest to change their own program .
Waiting for your reply .

Acer aspire 5733 windows 7 intel core 13 inside, setupwas unable to create a new system partition orlocate an .......

i woke up today to see my laptop asking for a current password i entered
then it was asking
please input password for st9500325as
and nothing seems to be working
i tried to reboot the system and then the error message displayed in the title comes when i click next screen asking fro where do you want to install windows, i havent connected anything on the laptop and just
1 disc0 unallocated space 465.8gb
and i cant partition it also
i clicked on drive option and clicked on new( thets the only one i can click from the options) and it waited for some time as it is trying to do something and telling me failed to create new partition, what can i do. [laese explain in astep bt step
procedure,
i am not a genius on laptops or computer

Hi,
Quote: setup was unable to create a new system partition or locate an existing system partition.
It can be caused by corrupt partition table.
Boot from Windows installation media, press Shift + F10 at setup screen, and run chkdsk command to fix drive error.
http://technet.microsoft.com/en-us/magazine/dd637756.aspx
Also, please remmember to mark your system partition as active using diskpart command, if you do not have a system reserved partition.
http://www.sevenforums.com/tutorials/71432-partition-mark-active.html
NOTE This response contains a reference to a third
party World Wide Web site. Microsoft is providing this information as a convenience to you. Microsoft does not control these sites and has not tested any software or information found on these sites.
Andy Altmann
TechNet Community Support

Premiere Pro CS3 Not Responding on new System

Can someone please help me out here?!?!? I just bought a brand new laptop. It haves an i7 processor, 8gb of ram, 1 tb of hard drive space, as well as runs on 64 bit with Windows vista 8.1 I believe. As we all may know Adobe Premiere Pro CS3 runs as a 32 bit program. Every time I try and open up a project I have already been working on prior to my new system and try to locate where the specific files are for it to link/synchronize, the Adobe Premiere Pro CS3 program freezes up and "Not Responding" appears causing me to press "ctrl, alt, and delete" to end the program using the task manager every time. Shouldn't I be able to run a 32 bit program on a 64 bit system? What can I do? Please help me!!! Thank you in advance!!!
[Text formatting corrected.]
Message was edited by: Jim Simon

2 things to try
Right click the program icon and, if available, select running in WinXP mode from the pop-up option window
Right click the program icon and, if available, select run as administrator from the pop-up option window
>Windows vista 8.1 I believe
As far as I know, that does not exist... current is Windows 8.1 (Vista is OLD and discontinuted)

Going to build a new system, is this gonna work ?

I'm going to build a new system with a msi k8n neo4 platinum motherboard,
but i'm not sure, that all the parts i have chosen will work with this motherboard.
So if you can help me.. u huge thanx !
AMD Athlon 64 3500+, 2.2Ghz, 512Kb cache,S-939,Box
Chieftec Mesh Long MidiTower, Zw/Zlv (LCX-01B-B-SL)
Creative SoundBlaster Audigy 2 ZS, oem
Kingston Dual-Channel 1Gb Kit, 2x512Mb, PC3200 (KVR400X64C3AK2/1G)
Lite-On DVD-Rom 16x48x IDE black, oem
MSI K8N Neo4 Platinum, S939, nForce4, ATX
Maxtor DiamondMax 10, 200Gb, 7200rpm, 8Mb SATA150 (2x)
Maxtor DiamondMax Plus 9, 120Gb,7200rpm,8M,SATA150 (1x)
NEC 3.5" Floppy Diskdrive 1.44Mb black
Zalman CNPS7700-Cu CPU Cooler S478/775/754/939
Papst Fan 4412FGL(E) 12x12cm, 1600rpm
XFX GeForce 6600 GT 128Mb,2xDVI, TVo,PCI-E, Retail
and i wanted one of these power supply's
Tagan TG480 Silent Power Supply 480 Watt
Enermax EG495AX-VE SFMA 485W Noisetaker PSU,ATX2.0

The chip works great with the board. The Tagan 480W PSU also works great with it.
I know the Zalman 7700 cpu cooler is bigger so may block the first two ram slots as it's tight with a 7000.
The rest of the hardware looks great though I know there's threads on choosing the right ram for the neo 4 in the stickies so check that out. Also the maxtor D-Max 10 might cause a problem not sure. I know people with the Neo 2 had problems.
Good Luck

Do search folders automatically include new system archive folders

Do search folders automatically include new system archive folders as they are created each year.
I decided to create filters and use these to keep track of various types of email, eg wife, mistress1, Mistress2 etc, friends, stamp collecting society, train spotting, bank etc
I can then just archive them all and see them in search folders.
Looks like I will have to go through each property to choose folders each year.
I need to know is this the case before I create 50 odd search folders for mistresses plus the others? :)

Hi Matt
Thanks for the reply but I'm not sure it answers the point I wanted to clarify
I can see your option creates a substructure in line with the original source email but does it also update a "saved search" folder criteria that this folder should be searched.
I am just working from my inbox and previously I would move emails to subfolders (basic filing) but this is a bit tedious dragging or selecting to the right destination. I just want to hit delete or archive then allow the "saved search" folder to work its magic with a filter.
Including a folder does not automatically cause sub folders to be searched so it seemed unlikely that come next year when a 2016 folder is created that the "saved search" folder will see the new folder.
My option still seems best for what I want even if I have to update 20 or so searches each January.
If any developers are watching the option to "include subfolders" in the criteria would get round the problem.

How do I prepare my iMac for sale? And best practice for transferring media to a new system.

This is my first time posting in a forum, so I will apologize in advance if I'm doing something wrong. I've tried to search for a very clear answer to my questions in the existing discussions, but have not had much luck.
I ordered a Macbook Pro today and would like to sell my current iMac to supplement some of the cost. I purchased my iMac in March of 2011 with OS X Snow Leopard preinstalled. I've since updated to Mountain Lion. When my computer came in it did not have OS DVDs, so I am not sure exactly how to take it back to factory default and remove ALL of my information safely in order to prepare it for sale. I'm afraid to tell it to format if I am going to need a boot disc/drive to reinstall the OS. I've been trying to research all day and have learned that I will not be able to sell it with the current OS, only the one that came with the computer at the time of purchase (to the best of my understanding).
Secondary to all of this, I have a question about backing up info and porting it to my new system. I have run the Time Machine backup to my external hard drive. However, I DO NOT want to port it to my new MBP as an image of my past machine. I did that when I got my iMac from my old MBP and my iMac thinks it is a MBP (MBP EFI/SMC Firmware Update Icons in my system utilities folder as well as identified as a Macbook Pro on my network). I've never been able to get all of these things to go away and I feel like it's chewing up hard drive space for no purpose whatsoever. I also worry that it could create system issues that I'm just not savy enough to catch before they are beyond control. That being said, I'd like to begin fresh with my new MBP. What is the best method of bringing my photos from iPhoto and music/movies/books/etc from iTunes to my new system? My word documents are easy enough...I keep 3 flash drives updated with them at all times.
Thanks in advance!

Whoever said you can't sell you iMac with the current Mac OS X is wrong, I believe.
Unfortunately, it is not wrong.
Any OS purchased/obtained at the app store - as is the case here - is not transferable. The license is tied forever to the Apple ID used to obtain it. The SLA states that the seller needs to erase the drive and reinstall the original system.
@ Kamikazwe:
You can call Apple and give them your serial number and they will send you copies of your original disks at a nominal charge.
You do need to use your original Snow Leopard disk, boot from it, erase the drive, and reinstall Snow Leopard. The buyer of the machine will need to purchase his/her own copy of Lion or Mountain Lion with their own Apple ID or they will never be able to reinstall or update the OS.
SLA Excerpt:
3. Transfer.
A. If you obtained the Apple Software preinstalled on Apple-branded hardware, you may make a one-time permanent transfer of all of your license rights to the Apple Software (in its original form as provided by Apple) to another party, provided that: the Apple Software is transferred
together with your Apple-branded hardware; (ii) the transfer must include all of the Apple Software, including all its component parts, printed materials and this License; (iii) you do not retain any copies of the Apple Software, full or partial, including copies stored on a computer or
other storage device; and (iv) the party receiving the Apple Software accepts the terms andcconditions of this License. For purposes of this License, if Apple provides an update (e.g., version 10.8 to 10.8.1) to the Apple Software, the update is considered part of the Apple
Software and may not be transferred separately from the pre-update version of the Apple Software.
B. If you obtained your license to the Apple Software from the Mac App Store, it is not transferable. If you sell your Apple-branded hardware to a third party, you must remove the Apple Software from the Apple-branded hardware before doing so, and you may restore your system to the version of the Apple operating system software that originally came with your Apple hardware (the “Original Apple OS”) and permanently transfer the Original Apple OS together with your Apple hardware, provided that: the transfer must include all of the Original
Apple OS, including all its component parts, printed materials and its license; (ii) you do not retain any copies of the Original Apple OS, full or partial, including copies stored on a computer or other storage device; and (iii) the party receiving the Original Apple OS reads and agrees to
accept the terms and conditions of the Original Apple OS license.

Portal Runtime Error while creating new system in portal content

Hi
Can anyone solve my problem, i am geting error while creating new system in p ortal content
Portal Runtime Error
An exception occurred while processing a request for :
iView : pcd:portal_content/com.sap.pct/admin.templates/iviews/editors/com.sap.portal.templateSelection
Component Name : com.sap.portal.admin.templateselectionwizard.default
com/sap/portal/iviewserver/cache/OClass.
Exception id: 11:29_26/12/06_0014_5891950
See the details for the exception ID in the log file

Hi,
Check this link for creating system object
http://help.sap.com/bp_epv260/EP_EN/documentation/EP/N03_BB_InstallGuide_EN_US.doc
Regards
Arun

Setting up a new system

Hello everyone,
I'm setting up a new system and would appreciate any comments on the components I've selected:
(the idea is to have a mid-range system, with room for upgrades in the future). thanks!
CPU
Overclocked Intel® Quad Core i7-3820 (3.6GHz @ max 4.4GHz)
Motherboard
ASUS® P9X79 PRO: INTEL® SOCKET LG2011
Memory (RAM)
32GB KINGSTON HYPERX GENESIS QUAD-DDR3 1600MHz X.M.P( 4 x 8GB KIT)
Graphics Card
2GB NVIDIA GEFORCE GTX 650Ti BOOST- 2 x DVI, HDMI, - 3D Vision Ready
1st Hard Disk
120GB KINGSTON HYPERX 3K SSD, SATA 6 Gb/s (upto 555MB/sR | 510MB/sW)
2nd Hard Disk
1TB WD CAVIAR BLACK WD1002FAEX, SATA 6 Gb/s, 64MB CACHE (7200rpm)
3rd Hard Disk
1TB WD CAVIAR BLACK WD1002FAEX, SATA 6 Gb/s, 64MB CACHE (7200rpm)
4th Hard Disk
2TB WD CAVIAR BLACK WD2002FAEX, SATA 6 Gb/s, 64MB CACHE (7200rpm)
Power Supply
CORSAIR 850W PRO SERIES™ HX850-80 PLUS® GOLD MODULAR
Processor Cooling
Corsair H80i Hydro Series High Performance CPU Cooler
Case
COOLERMASTER CM690 MKII ADVANCED CASE

I would not suggest raising the base clock to OC on that CPU. You may want to stop at 4.3GHz. That base clock frequency effects more than just the CPU.
Eric
ADK

New System - No POST, No Beep Codes

Hey guys,
So I built a new system last night, powered everything on and everything seemed to come on as expected but there was absolutely nothing on the screen. The system MIGHT be posting properly because I see the keyboard lights flash when I first turn it on, then the Numlock light stays on as normal. Also, when I press the numlock key it toggles the light as it should, and a ctrl-alt-del on the keyboard seems to reset the system as well (fan speeds change and lights blink just as they do when pressing the actual reset button on the case). Additionally, when I had the drives connected it sounded like it was checking them looking for something to boot (even though the hard drive is blank right now). However, I'm not sure that they're just making noise simply because they have power and are doing things like spinning down after not being used for a minute or two.
There are no beeps or alerts coming from the motherboard that I can see/hear. I also disconnected all the drives to see if that helped, but it was still the same thing. I have not yet tried to take the mainboard out of the case and running it with only CPU/RAM/video; I plan to try that tonight as a next step.
I'm guessing that this means there is something wrong with the video card, but I'm not 100% sure, and wanted to see if others had ideas before I try exchanging the video card. Unfortunately I don't have another PCI-E system that I can simply test the video card in.
This motherboard should beep if it detects a problem, correct?
Are there any LEDs on the board that could help me diagnose something? I don't think it came with a D-bracket. There are the 4 CPU_Phase LEDs on the board, and I believe two of them are lit up while it's running, but I'm not sure how to interpret those LEDS. Anyone know what exactly they indicate (more than what the manual says, which is just that 2, 3, or 4 lights indicates that the CPU is in 2-phase 3-phase, or 4-phase power modes).
Am I correct in assuming that since the lights on the keyboard seem to behave as normal and that ctrl-alt-del works as normal that the motherboard is probably okay?
Any other ideas or suggestions?
Thanks!

You can try to clear CMOS and try out with another video card.

New System Cause of Stress lol

Similar Messages

Maybe you are looking for