New Time Capsule 2nd generation keeps slowing down internet. Firmware 7.6.3
Both ethernet and wireless connections, my time capsul ( 2nd gen, 7.6.3) slows down to 20 Mbits after a day or so. I then plug the Modem directly into my laptop, and the speed is 90+ Mbits. I then remove the cable and plug it back into the TC, and the speed jumps back up to 60+ Mbits. 24 hours later, I am back down to 20 Mbts. Ideas anyone? How to I get closer to the 90 Mbits? I'd even be happy with the 60+ Mbits, but why the contant drop down to 20?
The OP does not have a modem router so this advice doesn't apply.
Similar Messages
-
My Time Capsule 2nd generation is the main accesspoint in my house. It resides on the second floor in our living room. On the first floor in our kitchen I have an fairly new Airport Express that extends my network on the 5 GHz band and allows me to stream music via Airplay. I had to choose 5 GHz since the 2,4 GHz band is interfered when using the microwave oven. However, we have a rather old house with loads of metal in the concrete walls and therefore the 2,4 GHz signal from the second floor proivded by the Time Capsule is hardly available on the first floor. Since all our iDevices (iPhones and iPods) operate at the 2,4 GHz band we sometimes don't have a proper wi-fi connection. I had tried before with another (older) Airport Express that only operated at the 2,4 Ghz band, but I could get a proper connection between the Time Capsule and the Airport Express. Therefore I think it would be the best solution if the new Airport Express would provide both bands simultaneously.
If I replace my existing Airport Express with the new one, will I be able to extend my network on both bands?It sounds like you may have configured your Time Capsule to use a separate name for the 5 GHz network and then setup the Express to extend that specific band.
In order to extend both bands, the Time Capsule setup will need to be changed so that both bands are using the same name. In other words, you would uncheck the option for the 5 Ghz name.
Then, setup the new Express to extend the Time Capsule network.
This is the only way that they Express can extend both bands. It cannot extend both bands if you have assigned a separate name to the 5 GHz network since you will be forced to choose either the 5 GHz band or the 2.4 GHz band for the Express to extend.
How the microwave oven will affect this is not known. This will one of those things that you have to try in your home to know if it will work well, so it might be a good idea to understand the store's return policy before you buy....in case things do not work out as hoped. -
Just installed new Time Capsule, wifi now very slow, what amI doing wrong?
Just installed new Time Capsule, wifi now very slow, what am I doing wrong?
It's possible the reason it seems so slow, is that a backup might be in progress - and since it's the first backup everything on the disk is something that Time Machine is backing up and is being transferred across the WiFi at the same time as you're trying to use your Internet. So you're competing with Time Machine data flying across your WiFi along with your internet stuff. So if this is indeed what is happening (look at Time Machine to see if a backup is in progress), either pause the backup to a more convienent time or live with the slowness till the backup is done this first time, and after that you probably will not notice the "competition" on your WiFi. I like to schedule the Time Machine backups to late at night rather than once an hour (the default), but that schedule should be whatever you feel most comfortable with.
There is a handy free utility called "TimeMachine Editor" that you can get from http://timesoftware.free.fr/timemachineeditor/ that lets you create your own customized backup schedule. You can create several schedules to fit your working conditions. I've used it for several years with never a problem. I don't have anything to do with the company - just a happy user.
Good luck... -
Using two Time Capsules - 2nd as backup drive without internet
Let me explain the setup first:
I have Motorola SurfBoard SBG6580 <-> to this is connected my NEW Time Capsule 3TB via Ethernet
This new 3TB TC provides internet and Time Machine back ups to my iMac and Macbook.
So far everything is good!
Now, I have my older 500GB TC.
I want to use this TC merely as a wireless harddrive for secondary backup (maybe using Time Machine or maybe just as wireless drive where I can manually move files to and from whenever needed).
What I want to do is quite simple. I want to be able to plug this TC into a power source and connect wirelessly to my iMac and Macbook.
Since It was previously being used on the SB6580, I had though that that I would be able to do this painlessly! Simply remove the ethernet cable from the SB6580 and I would have the new TC 3TB provide internet and TM backups and the older 500GB TC as secondary backup device. But once disconnected from SB6580, I can't "see" this old 500GB TC. What am not doing right?
Help is much appreciated.
ThanksTemporarily, move the old TC to the same room or close proximity to the new TC
Power up the old TC for a few minutes, then hold in the reset button on the back of the device for 8-10 seconds and release. Allow a full minute for the TC to restart to a slow, blinking amber light
Open up AirPort Utility on the Mac
Click on Other WiFi Devices
Click on Time Capsule
The utility will open up and take a minute to analyze things, then announce that the old TC will be configured to extend the new TC network
Enter a name that you want to use for the old TC.....you can use the same device name that you used before if you wish.....and click Next
The utility will set up everything for you. When you see the message of Setup Complete, click Done
Move the old TC to a location where it can pick up a good quality wireless signal from the new TC. -
Slow transfer rate to time capsule - 2nd generation - mb pro 5ghz
alright
have time capsule with dual networks, macbook pro with n enabled connected to 5ghz network with full bars, yet while copying files to the time capsule, it seems slow
500kbs per second
about 7 min to copy a 744mb file to time capsule (according to finder)
time capsule connected via ethernet to 2wire 2701hg modem + wireless router ( wireless turned off )
configure ipv4 using : dhcp
ethernet wan port: automatic
connection sharing : share a public ip adress
ipv6 : link local only
wireless options
country - mexico
multicast rate - high
transmit power - 100%
use wide channels
any ideas?
thanks in advanceHi,
In the Manual Setup->Advanced->Logs and Statistics page of Airport Utility you'll find information on wireless signal quality for each client connected. Primarily, signal quality will determine the connection speed of your file transfers, the best you can do to improve things is to find a wireless channel with the least interference, Manual Setup->Wireless.
My Macbook Air connection is showing -66 Signal, -89 Noise, 122 Rate which gives me a wireless file transfer rate in bursts from 500kbps to 22Mbps. Time Capsule is not the fastest combo device, even file transfers over LAN Ethernet are around 50% slower than a regular Airport Extreme and I've found transfers to the disk from a GigE connected Mac Pro top out at around 60Mbps.
The Time Capsule is more useful as a convenience tool than speed I think so just be patient. -
My 1st Generation time capsule won't connect to the internet thru a new motorola sb6121 - get continuously flashing yellow light. Using a router in between the modem and capsule yields good but slower connection to internet. Any thoughts?
Thanks for your response
Let me give the history - I started with an Apple Express being fed thru a D-Link EBTR 2310 cable Router from an RCA DCM315 Modem (Pure). Comcast service all the way.
Got the 1st generation TC in 2008 and merely replaced the Airport Express with the TC. Worked ok
A year or two ago I did try removing the modem and feeding the TC directly from the modem. Resulted in the same condition I have now - Continuous flashing amber on the TC. So I put the router back in the chain.
Some time later, at the recommendation of a Comcast rep, I replaced the router with (a Belkin F5D 5231) to see if speed and dropout problems would be improved. I thought it helped some at the time but now I am not so sure.
Last week I decided to see if a new modem would help with download speeds. So I got another pure cable modem (Motorola SB 6121- high on the Comcast recommended list).
Got up and running easily with Comcast help and with the modem connected directly to a computer.
Next I put the TC in the link and again could not get past the TC continuing to flash amber. Although I did get connected to the internet with this configuration I lost connection two both of my printers - one connected by USB and the other wirelessly to the TC. Again everything works fine when I put the Belkin router back in the system.
However with the router in there, the modem shows the downstream connection to be 10/100 ethernet speed. (Modem light changes color for indicating speeds.}
I have gone thru all of the combinations of powering down/ up, but all stays the same.
I can live with what I have but something still doesn’t seem right.
Thanks again -
I have working Netgear N600 dual band router network. The existing network has an XP netbook PC, canon printer, 2 Iphones, Epson Air printer, an Ipad, 3 roku boxes, backup drive. Just bought a new Apple TV box, and time capsule 2T. I have an IMac on order but don't have it here yet.
My goal is to add new Time Capsule and create 2nd "apple" network for new apple TV, Iphones, Ipad, Epson Air printer and new Imac, and keep the netgear network for my PC, Roku TV boxes, and Canon printer and backup drive.
The Netgear router, the time capsule and new IMac will be on the same desktop, I dont need to backup my netbook PC to time capsule.
Where do I start?
Which device connects to my modem first, the TC2 or the Netgear?
Is it best wait for the Imac before starting or can the TC2 be set up from my Ipad or PC?
Thanks.It is pretty simple..
Setup the TC in bridge and plug it into the Netgear.. I would leave the netgear as the main router for now, although in the future you can swap things around. The netgear firmware may have issues with bonjour and airplay/airprint?? Does your ipad print ok now?
You can setup the TC using Mac, PC (at least up to win7) or iOS.. they all have airport utility available.
Bridge mode is set differently depending on the version of the utility. This is v5 and how the windows one will look (at least similar to).
v6 will be as
With the TC in bridge you will still create a wireless network.. and give it a different name from the netgear.. then all the apple devices can connect to it. Use ethernet rather than wireless if the imac is on the desktop with it. Much faster and better for using Time Machine backups.
If you run into any issues.. just post the particular issue. It will take a bit of getting used to, but isn't hard. -
my ipod touch 2nd generation keeps taking screen shots by itself and turning off. This is a 'NEW' replacement and is less than 12 months old. Any ideas?
Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar -
Problem with new Time Capsule w/ 7.5 Firmware Slow Speeds on 802.11b/g
I purchased a new 1TB Time Capsule with v. 7.5 Firmware last week. This Time Capsule is replacing a first gen 500GB TC with Firmware v. 7.4.2. I have 2 Macbook Pros connecting to the new Time Capsule via 802.11n at 5Ghz and 2 iPhones and 1 first gen Mac Pro connecting to it via 802.11b/g at 2.4Ghz. The Macbook Pros connecting at 5Ghz move data fine. The connection is very fast. Speedtest.net average about 20Mbps down and 2Mbps up. The devices connecting on the 2.4Ghz radio are slow as molasses. They test at less than 30k down and 30k up. Beyond that they have trouble moving data around the LAN as well. There are no sources of major interference near the TC. In fact the TC is in the same location as the old unit which was also running at 2.4Ghz with no problems. I contacted Apple tech support and then went to a local Apple store for an exchange. They gave me another new TC but the problem persists with the new units as well. This evening I took the new Time Capsule into the basement and isolated from any kind of interference with no success. I plugged in the old TC and the 802.11g devices were back up to speed.
Has anyone had any similar issues with the new AE or Time Capsule? I'm sure it's not unheard of to get two defective units but it's not likely. So I am thinking there may be an issue with the new firmware. I tried to downgrade to 7.4.2 but the new units require 7.5. Any suggestions? All network settings are the same as they were with the previous Time Capsule. The only thing that's changed is that both the 2.4Ghz and 5Ghz radios are active.Hi there,
got some problems with Time Capsule and 7.5 Firmware as well. Since it is my first device, I have no experience with older firmwares or models though.
It is impossible to connect to the 5GHz network. Neither when I have 5GHz and 2.4Ghz in one network or when I set a separate network for the 5GHz.
I always get a timeout message, I also tried deactivating the guest network and I also tried without any password, just would not connect to the 5GHz. By the way, I am sitting 50cm away from the TC and of course, I do have a MacBook Pro that supports 802.11n standard, a brand new MacBook Pro 13.
So, any ideas? I'm going to call Apple on Monday, can't check if it's the notebook, cause I do not have a second device to test ist. My iPhone works fine (802.11g), the 2.4Ghz also works fine with rates around 130-145 usually when close to the TC.
I also noticed that my MacBook Pro won't connect to the 802.11n when compatibility with 802.11b/g is activated. Then it runs with 802.11g instead....
pretty annoying, thought this would work right away?! -
I recently purchased a brand new Airport Time Capsule 2TB. I already am using the previous generation time capsule to back up all my computers data. May I ask how can I complement the usage with my new time capsule?
By default your new Time Capsule will broadcast an unsecured wireless network with a network name of something like: Apple Network NNNNNN
Most likely your iMacs will be connected to the wireless network created by the Virgin Media router. However, both should see the Apple Network under the AirPort icon's drop-down menu as another wireless network that they can connect to. Is this not the case? -
My new Time capsule 802.11n (4th generation) remains saving after a long time (3 weeks) but there is no backups files in time machine. It seems that it is working without results. What should I do?
Hello, no experience with TC, but...
Have you looked through Pondini's extensive TM help site?
http://Pondini.org/TM/FAQ.html
http://pondini.org/TM/Troubleshooting.html
Can't imaging something not being covered there. -
The new Time Capsule is amazing
I just got my new Time Capsule with 2TB storage. It replaced the previous generation Time Capsule, again with 2TB of storage.
In my network I have a Retina Macbook Pro (early 2013 model) and a 11" Macbook Air (mid 2013). My internet connection is 150Mbit/sec download and 5Mbit/Upload.
With the previous Time Capsule my rMBP would achieve a maximum of 15MB/sec download and my MBA 16,5/sec.
Now, with the new Time Capsule, my rMBP achieved a whopping 17MB/sec!!! I still haven't tested the MBA, but I am confident it can achieve up to 18MB/sec (my maximum download speed).
I can only say that I am amazed how good the new Time Capsule is. Kudos to Apple!The Gen1 hard disk was a noisy beast although you would have to be up close to hear it still. Modern slow green drives are much better and run cooler.
The new TC runs the standard WD green drive.
See the review here which has a tear down included.
http://www.anandtech.com/show/4577/airport-extreme-5th-gen-and-time-capsule-4th- gen-review-faster-wifi-/4
The problem in Gen1 was a philosophy and a take over by the Interior Decorators at Apple rather than the Engineers. The excellent fan control built into the unit was dismissed as Overheated Engineer Imagination.. OEI for short. The fact that they stuffed a hard disk and power supply into a box slightly bigger than the Extreme.. had nothing to do with subsequent problems.. gollum.. gollum.. according to the Interior Decorator department. Engineers did actually calculate the reactor melt down temperature and turned on the fan to prevent said event.. they turned it on at 100% speed and 100% noise. Because it was seconds away from disaster..
Gen4 the design finally used the fan properly and offers some proportional control.. but you cannot expect no noise out of a plastic box dissipating 30W when it is doing the full job, backups, routing, wireless, gigabit. It still fails in having no fresh air inlet. So stand it on feet to stop the heat build up underneath.
During normal duties though and in normal weather.. you will hardly ever hear it. -
New Time Capsule does not see Airport express
Hi
We purchased A new Time Capsule but are not able to get the existing Airport Expresses to work with it. I tried looking for the AE with AIrport Utility and cant see them.
Any idea how to get these to work with our new Time Capsule 3 TB? My Airpot Utility is Version 6.2
Thanks
JennyI've reset one of them. no luck
Suggest that you try the following if you have not already done so.
Power down the AirPort Express (AX) for a few moments
Hold in the reset button and keep holding it in for 10-12 seconds while you plug the AX back in to power
Release the reset button and allow 40-45 seconds for the AX to restart to a slow, blinking amber light
Move the AX near your Time Capsule and computer
Temporarily, connect a spare Ethernet cable from your computer to the AX
Open AirPort Utility to configure the AX
If you do not have a spare Ethernet cable handy, the AX is broadcasting a wireless signal with a name like Apple Network xxxxxx. You must first connect to this network from your computer.
Then, open AirPort Utility. You may be asked to "switch" networks so that AirPort Utility can connect
If you use the recommended Ethernet cable method, you can disconnect the Ethernet cable once the AX has been Updated. Then, move the AX to the desired location.
Configure the second AX like you did the first.
If you have the older "b/g" version of the Express devices, unfortunately you will need to configure the Time Capsule and Express devices to Participate in a WDS network if you need to enable the Ethernet ports on the AX devices.
This will result in the Time Capsule being changed to a "g" wireless router, since WDS will only operate at "g" wireless speeds. -
WiFi no longer working with new Time Capsule-can you help please?
Hi all,
Just received my new Time Capsule (TC). It was a little problematic setting up, but probably due to my now choosing to increase my security from WEP to WPA as the TC set-up assistant suggests. Since then, I have had numerous problems getting my other computers and now my iPhone to connect with WiFi.
The problem is that despite entering all the new settings and WPA passwords for my connection with the TC, the iPhone will either momentarily recognize and go to wifi or simply stay on Edge.
On the former, with wifi active, as soon as I go to iTunes, Safari or check email, it reverts to Edge. On the latter, despite resetting, entering password, or tapping Settings and selecting my wifi connection, it will NOT connect and stays on Edge.
(Now, I'm on Edge! I'm bummed that with new hardware I have new problems that didn't exist before!)
Can someone who had this same problem tell me how they resolved it.
Here's the one clue I have, but would rather not resort to: When I first set up the TC, I had it on WEP with a WDS Network, and everything was working great and FAST! Now that I have increased the security—I will be backing up 3 computers to the TC—my iPhone and other computers seem to have intermittent or no wifi connection as a result.)Irving Gonzales,
If your computers are 802.11N capable, you might want to try an advanced setup that might help your Time Machine speeds some. I have not personally tested it, so it is just a personal theory at this point.
First, in a mixed environment the 802.11N clients all get slowed down.
First, configure the TC for 802.11N only.
Second, connect the Airport Express via ethernet to the Time Capsule
Third, configure the Airport Express for bridged mode (doesn't give out IP addresses), and for its own wireless network with a different name than the Time Capsule.
Have any 802.11b/g clients like the iPhone join the Airport Express' network.
Thank you,
Nathan C. -
Setting up Air play with new time capsule and newer airport express?
I just recently purchased a new time capsule, and I'd like to use my current generation airport express to stream music from my apple devices. I just was wondering what I had to do in airport utility to set this up? I was also wondering how to transition the network over from the old express to the new time capsule as far software settings go. I really appreciate the help and assistance. Thanks folks. I'm really looking forward to setting up the network for our new iMac.
Your setup is very easy..
This is how I would do it.
Remove the express from the network.. ie just unplug it but do not change anything in it. Keep the configuration as is until the TC is working.
Power off the cable modem.. this is requirement.. at least 20min is usually needed, dependining on your ISP.
Go into the airport utility and setup the TC as router for your network .. it is a simple setup.. but I would do as stated.. all short names, no spaces pure alphanumeric rather than accept Apple's names. That is for TC and wireless.
After 20min power up the cable modem. Once it is running and you have internet access. you can proceed to setup the express to do the airplay. If the internet still doesn't work, power off the cable modem overnight..
Do not lose that express setup so if you absolutely have to, you can at any time substitute it back and have internet again.
So everything is working properly TC in place as full router.. now hard reset the express.. and simply use the airport utility to put it in extend wireless .. or plug in by ethernet if you are going to hard wire it.
The extend wireless setup is all done straight from the existing setup.
Now you can plug your express audio port into your speaker.. and setup the airplay via the itunes.
I will get Bob to give you his way of doing it.. There is no one RIGHT way .. but he can give you more info if you want a particular method.
Maybe you are looking for
-
Can I use the new Time Capsule to backup my mid 2010 Macbook Pro? Also can I want to free up my hard disk, can I save my photos and files on the time capsule and later access through wifi?
-
Cannot use create purchase order in SRM 7.01
Hello, We are upgrading from SRM 5.0 to SRM 7.0.Classic scenario. In the workset purchasing of the role operational purchasing you can use Create Documents -> purchase order. if I click on it I recieve the following message: The table does not conta
-
Cant preorder destiny the taken king digital download
The bonus items only unlock once taken king is released, if you go to the pre order in store you should see the list of time locked content.
-
I cannot install adobe reader on window XP
-
Having edited photographs in editor and saving the edited photograph, it says processing but does not save the edited version and i am left with the original. Forgive me if i have filled out the questionaire wrongly as i am new to this kind of thing?