New WRT-160 V2 firmware posted

New WRT-160N V2 firmware (build 15) is posted.
http://www.linksysbycisco.com/US/en/support/WRT160N/download
I have had it up (as a beta) for three week, no problems
I used Firefox to install / flash instead of Safari///

when you connect your com to the modem the speed got to be faster
because your are getting direct connection with the modem.
when you use the router the speed gets slow because it handles multiple devices at the same time
however as you mentioned that it is reducing your speed to 1-2meg download and 1 meg upload.
that seems to be really bad .try to hard reset the router for 1 minute then reconfigure your router from the scratch
after that upgrade the firmware on the router and power cycle the entire network.and set the wireless security as WPA2 personal that would give you good speed on the wireless computers. also try to reduced the MTU to 1364....
once you are done with these troubleshooting then you would Definitely get the better speed .

Similar Messages

New 5800 RM 356 firmware 52.0.007 is released..!!

new 5800 RM 356 firmware 52.0.007 is released..!! check out for new fixers..

ok guys this is what i found till now:
The browser has been updated.
Nokia maps has been updated.
The QWERTY has changed a bit.. There's a gap between the zxcvbn line and space bar line..
The 3D effect on the ringtones are working now.
RDS is working properly..
Ammm.. Well this is what i'v discovered as yet.. Will keep posting..
Regards,
Dr. Shoubhik

What is new in Nokia 6300 firmware v07.00

Hi I have just upgraded my Nokia 6300 to firmware v07.00. I can't notice any visible change with this new firmware. Can anyone put some light on what is new in Nokia 6300 firmware v07.00
Hyp3rion

After updating mine yesterday...da screen refreshes or so flickers every say 5 seconds...plz any help
i have reinstalled it three times... ..still no solution
Message Edited by prubyholl on 04-Dec-2008 07:20 PM

HT1414 I dont know why bt ever since I updated my iphone 3gs 16GB to the new 5.1.1 firmware I am unable to activate it with my any sim card, so is there any way to fix this. Im from India

I dont know why but ever since I updated my iphone 3gs 16GB to the new 5.1.1 firmware I am unable to activate it with any sim, so is there any way to fix this please? Is there a solution to activating my Iphone 3gs on this firmware? I purchase this iPhone from USA and Im using it in India. Please help me...

This means the iPhone was hacked to be unlocked. The 3GS was not sold in the US as officially unlocked.
Restoring an iPhone with iTunes that was hacked to be unlocked or installing a firmware update on an iPhone that was hacked to be unlocked re-locks the iPhone to the carrier the iPhone was sold as carrier locked when new. In this case, re-locked with ATT.

New transaction key with the posting key 24 and 34

Hi,
i want to create a new transaction key with the posting key 24 and 34.
the corresponding table is T030B.
but what is the Tcode/ IMG path to create it?
Regards,
Swetha

Hi,
Go to FBKP. Click on Automatic Postings.
Suppose you want to see the Exchange Rate diff. then click on it. You will see the transaction. Suppose KDB. Then double click on it. Now click on posting keys. The same will be defined in the table which is given by you.
Regards,
Jigar

Help very Need WRT 54G V7, firmware 7.00.6

Help very Need WRT 54G V7, firmware 7.00.6
I updated to 7.00.8 and now device work not stable
WhenI have 7.00.6 firmware it work not bad.

Well its not possible to restore the earlier firmware back on your Router. Since you have already upgraded the firmware on your Router, Have you resetted your Router and re-configured all the settings on it again? Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...

WRT 160 N compatible with vista

I am thinking of buying this but I need to know if the WRT 160 N vista compatible thought I read it was not compatible.

It will work, router is independent of the operating system used.

Any News of update of Firmware for N95-3??

Hi
Any One know about News of update of Firmware for N95-3 ?? When a version V.30 for n95-3?
Sorry for my broken english.

It may be next week, next month, next year or never.
It's impossible to answer that question here as nokia never announce new firmware until it's available.

New ZEN(8GB) showing FIRMWARE PROBLEM after first connection to

New ZEN(8GB) showing FIRMWARE PROBLEM after first connection to PC?I havn't even use it?Can someone help me ?Message Edited by chrisstrong on 0-07-200707:50 AM

tell me about it. I've rebooted it then left it for a few minutes. after that it seems to start. I also used another usb cable which seems to have helped (weird i know!)

Wrt 160 NL storage access from internet

Hi,
I would like to ask if there is a way how to access my HDD connected to USB on wrt 160 NL router via the internet (I have external IP adress)
I know its possible with routers which have FTP.

@ dibbler:
Seems that your statement doesn´t match at all to what is written in the product sheet of WRT160NL, look at this screenshot of the document.
If your statement is true, then I guess we should claim our money back, I don´t think that Linksys / Cisco are missleading customers to buy products that doesn´t perform as advertised. And this feature is the one that drove my decision to buy the product
By the way, I got to this thread precisely because I haven´t been able to access the storage link over the internet
and I really believe that Cisco should be doing something to explain how to accomplish it, there´s no instructions at all about this feature.

WRT 160 NL Storage acces from wireless

Hy,
Please help me with on issue regarding conection from wireless network to usb storage device. With the device from wireless I don't see the storage atach on the router WRT 160 NL, if you have any idea please tell me
Have a nice day,
Mihai

I have encountered a problem about that. Linksys has an article that shows the step by step instructions on how to access the storage on your router. Here's the link. Hope this helps!!

Bought a new computer, and new ipod 160 GB. I went to sync all my music and it's telling me that the computer isn't authorized. I authorize it and it still won't let me syn these songs

Bought a new computer, and new ipod 160 GB. I went to sync all my music and it's telling me that the computer isn't authorized. I authorize it, by going to store and authorize this computer, and it still won't let me sync these songs

Think you got to reboot or relaunch iTunes after the Authorization.
but here is the Apple support Article on Authorization and sync to iPod
http://support.apple.com/kb/TS1420
http://support.apple.com/kb/HT1420
Good luck!

New rig 990fxa-gd80v2 wont post debug code 19

I am building a new rig for my gf's brother and i can not get my new mobo to post. I am getting debug code 19. I couldn't find a lot of info on what the code means but from what I have seen its apparently a problem with the BIOS not being updated for my new CPU. I have tried all of my current working components from my rig on the board as well and it still showed code 19. Here are the specs on the rig.
MOBO 990fxa-gd80v2
CPU AMD FX-8320
PSU 500W RAIDMAX
GPU EVGA GeForce GTX 560 Ti (Fermi) 1GB
RAM G.SKILL Ripjaws X Series 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 1600
Like I said however I took apart my rig completely and switch all my known working parts onto the new MOBO and got the same error code. So I am not sure if the issue is really an outdated BIOS because it wouldnt post with my AMD Phenom II X6 1100T Black Edition. Any help would be greatly appreciated.

ok so it has been a few days since I last posted because I have been busy but I just finally had time to work on it. I essentially took out my mobo and replaced it with the new one that had been posting code 19. Using all my known working components from my computer including my PCU I am still recieving the same error code, even after moving my known working RAM into each different slot.I'm getting quite desperate here now and just am plain lost in trying to understand what seems to be the issue. I'd be very grateful for anyadditional information/tips here. Thanks.

New to the WRT300N - Firmware & help needed

Hi. First off, I apologize that this is going to be very long. I really hope someone will take the time to read it all and give me some help.
I posted about a week ago about problems with my WRT54GS. All of a sudden with no changes, the wireless stopped working. I tried for a few days to fix it with no luck. I decided to order the WRT300N (I figured if I was going to buy a new one, I'd upgrade and this is the one that Linksys recommended).
I should mention that after ordering the new router, the wireless on the old one started working again but it wasn't working normal. The signal quality had always pretty much been excellent and now it started going up & down but at least it was staying connected.
The new router came today. I disconnected the old one and connected the new one and everything went smoothly. Both my wired & wireless computers worked great. Less than an hour later, the wireless disconnected. I went to view available networks and my network (I use our last name) was gone. I shut off the laptop and it still didn't see the network. So I started looking at the router settings just to be sure that nothing had changed. About 15 minutes later, the laptop found the network and connected again. The signal quality dropped to good and has stayed there ever since.
Just for information, when the laptop is on the desk (which it is 90% of the time), it's only about 5 feet away from the router. I have not tried to take the laptop out of the room yet. Also more information if it helps. I have a large "U" shaped desk. My monitor for my desktop sits in the middle. On either side are the speakers. To my left (in front of me) is a UPS (plugged into this UPS is the tower, monitor, speakers, cradle for my mouse, modem & router), then the tower (I can't put it on the floor because I have physical issues that would prevent me from accessing it there). Now if I turn my chair to the left, the desk has an upper level. This is where my DSL modem & the router are. They are on the end near where the computer is on the lower level. This is the same setup we were using before. Old router worked great for almost 2 years with signal strength at excellant on the laptop. It just started acting up all of a sudden. If I go back to facing center and then turn to the right, that's where my husband's laptop sits. The only other equipment there is a calculator and a lamp and on the floor is another UPS which has his laptop (which has an Intel wireless G card in it), a laser printer, and the above mentioned calculator & lamp plugged in.
Prior to today, I had the Logitech MX3100 keyboard & mouse set. I had purchased a new mouse (Logitech MX Revolution). So I was using the keyboard from the MX3100 with the new mouse and everything was fine running that way for weeks before the problem kicked in. So I don't think it's got anything to do with the mouse. Today's setup is a little different. I am no longer using the MX3100 keyboard. I am using Logitech DiNovo Edge, which uses a bluetooth dongle. I also don't think it's any interference from this keyboard since this is a pre-existing problem.
I do have a cordless phone in the room (it's on the left hand side of the desk from where I sit at the opposite end from the modem & router...also it's one of those that doesn't need a phone line)but it's a 5.8 ghz.
The old router had the option to change the channel, etc. This one has auto for standard channel & wide channel & there's no way to change it that I can see. Radio band is also set to auto but does have 2 choices under it (standard & wide). As I said before, I use our last name for our SSID. It's the same one I've been using for years. There is no one else around here with that SSID. Network mode is mixed.
Concerning the firmware....the information for mine is WRT300N V1.1 firmware v1.51.2. I tried to look for an update but the only one in the list is the WRT300N V1.0. I did click on that but the firmware version is lower and I don't want to screw anything up. Is there a firmware update for me or not? If so, please point me in the right direction as I can't find it.
Concerning the signal strength....would it help to buy a new wireless card for the laptop? The Intel card has been updated with the newest software. The card is internal and to my knowledge can only be replaced with the same card or a bluetooth card. (Computer is a Dell XPS M140.) I do have a card slot but I'm confused because I think Dell called it an Express Card slot and I don't know whether or not the Linksys notebook card that is recommended for this router would work in this slot. If the card would work, is it worth the expense?
What else can I try. I thought about moving the router furthur to the left but it would require moving a few other items and I'm not sure if the cords are long enough. Would it help if the router & modem were not plugged into the same UPS? I do have a regular surge protecter near where my phone is. I would really rather leave them plugged into the UPS though for obvious reasons.
Also if it helps, I have the router on it's side with the 2 antennas on the end pointing straight up and the flat one in the middle I have angled this way.
I hope I have given enough information for some suggestions.
Thanks,
Lisa

Thanks for the response. I was wondering if anyone would take the time to read such a long post. I wanted to be sure to try to give as much information as possible.
My desktop (Dell XPS400) tower is made out of metal...but the router is actually not sitting on it. There is a shelf to the left of my tower (when I'm facing it, otherwise it's to the right of it). That's where the modem & router sit. The shelf sits about 3" over from the edge of the computer and it's about 7" above it.
As far as the wireless card for my husband's laptop...I'm still thinking about it. I'm wondering if there would be any improvement in speed or the quality of the connection with the N card.
Now I just went into the router's settings and tried to make the changes you suggested. I was able to change the radio band from auto to wide BUT once I do that, I loose the ability to leave the wide channel & standard channels on auto. The options for the wide channel are 3-9 and the standard are 1 & 5. I don't know which ones are best to pick so for now I'm not changing anything. I didn't change the advanced settings either as I wasn't sure if I could do that without changing the other settings first.
My husband has noted that he does see the quality of the connection occasionally jump to excellant. For the most part it's staying on good in here. We haven't brought it out into the living room yet to see what it does out there. He hasn't needed to. He has had it disconnect on him a couple of times as well.
I did forgot to mention in that book I wrote that we do live in an apartment building. We are on the 1st floor in the back of the building. Our office is between our living room & another bedroom. There is an apartment above us. There is another apartment on the other side of the other bedroom. Our bathroom is across the hall from this room, other side of that is the kitchen and then there is an apartment in the front of the building. Our front door is off the living room, a hallway seperates our apartment from another one. There are 4 apartments on each floor. Laundry (directly under us) & storage in basement.
I give all these details to try to get the best help. I don't know if all this extra info is helpful or not. We have been using Linksys routers for quite a few years now. This is our 3rd one and our 2nd wireless one. We have been in this apartment for a year now and had no trouble until a few weeks ago. Previously lived in another apartment of the same floor plan in the same complex but on the 3rd floor (boy did we hate walking up those stairs!) with no trouble.
Looking forward to hearing back from you so I can try to make the changes you suggested.
Thanks,
Lisa

Comcast new customer screen after firmware update

Every time I try to update my Airport Extreme's firmware, I get the Comcast new customer screen on my browser and can't access any pages other than that. I've had Comcast come out and they it is a problem with my router and not with them since I can surf the internet when my computer is hooked up directly to the modem. I've tried everything including resetting the Airport and cycling the power and nothing works. The only way I can continue to access the internet is when I upload the factory firmware version to the Airport. Has anyone had this problem before or have any suggestions on how to remedy this?

yeah I recall that pain in the butt problem. You probably had them(Comcast) install their so called mac software which you should not have done .
When my memory comes back I'll post the counter measure.
Although try this in the meantime;
ethernet from Comcast modem to wan port of apple router. ethernet from your Mac to lan port of Apple router. Power off the modem and the router. Bring the modem up first then the router. Place the router using DHCP and set your wireless config if need be. Should work.

New WRT-160 V2 firmware posted

Similar Messages

Maybe you are looking for