Newbie: 7210 style and 9914A style controller ??
I'm new to GPIB, and am considering implementing Labview or HP VEE.
I'm in the stages of identifying a controller that supports both
packages. I've seen some references to 7210 style and 9914A style
cards. Is there a significant difference, or is this transparent to my
application? Is it dependant on the software application, or the
equipment I am interfacing with?
Also, where's a good place to get GPIB cables? Controller (preferably
PCI)?
Thanks.
Sent via Deja.com http://www.deja.com/
Before you buy.
[email protected] wrote:
> I'm new to GPIB, and am considering implementing Labview or HP VEE.
> I'm in the stages of identifying a controller that supports both
> packages. I've seen some references to 7210 style and 9914A style
> cards.
Unless you are designing equipment that uses these ICs there is no need
to worry about it.
FYI the 9914A (from TI) is no longer available
The 7210 (from NEC) is only marginally superior.
National Instruments makes replacements that are supersets of these old
ones.
They also make one that is much better than either.
> Is there a significant difference, or is this transparent to my
> application? Is it dependant on the software application, or the
> equipment I am interfacing with?
It makes no difference
>
>
> Also, where's
a good place to get GPIB cables? Controller (preferably
> PCI)?
>
Since I like NI (National Instruments) I sould say you can buy everything
you need from them.
I will say that their cables are a little less rugged than those available
from HP
(Hewlett-Packard or is it Agilent now ??).
Some GPIB caveats:
No more than 15 devices can be connected to the same controller.
At least half of these must be powered up.
Maximum cable length is 15m (you can usually get more at lower speeds).
No more than 2-3 m between each device.
None of these are hard and fast rules but if you follow them there should be
no problems.
Shameless plug GO WITH LABVIEW !!
Kevin Kent
Similar Messages
-
I am a newbie...and I think I did a big no-no as my Ipad isn't working. I synced it to a second computer at work which is a new Imac after already syncing to my pc at home with Itunes. Now it says it can't restore and can't get it to open, getting error messages but can't fix myself. Can anyone help??
iPad can connect only in one iTunes Library. If you want to connect it to a iTunes Library then you have to erase it. You can erase it from iTunes. Make sure you iPad doesn't have a password, or if it has a password make sure that you connect to the computer and enter the password of your iPad
-
Z600 workstation missing pci data acquisition and signal processing controller driver
I just installed Win7 Pro x86 on my Z600 workstation. It was an upgrade from WinXP Pro. In Device Manager I am missing the driver for the PCI Data Acquisition and Signal Processing Controller and Hardlock USB 1.02. Can someone assist me in finding these drivers. I looked on the Support/Drivers page for this model but couldn't find anything.
This question was solved.
View Solution.Hi,
You might get better assistance on the HP Enterprise Business Forum since you have a professional worktsation.
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT -
PCI Data Acquisition and Signal Processing Controller driver
I've installed win 8.1x64 on my HP Probook 450 G2 but I am missing the PCI Data Acquisition and Signal Processing Controller driver.
Can you please help?
Thanks,
Leontina
This question was solved.
View Solution.Hi:
Please see if installing the Intel Chipset driver installs that device.
https://downloadcenter.intel.com/Detail_Desc.aspx?DwnldID=20775&lang=eng&ProdId=816 -
Pci data acquisition and signal processing controller -Device software not installed
My pc shows me ,the driver software for pci data acquisition and signal processing controller is not installed on my Device manager.
Please suggest me a suitable solution.No its not working , Give me an alternate solution.
-
How to install the driver of the 'SCSI and RAID Host Controller'
Hi,
I have two Windows XP(32Bit) installations:
•Windows XP SP2(32Bit) which is old and it seems as if it is infected by some viruses.
•I have installed another fresh clean Windows XP(32Bit) SP3. However, I have found that there is no category named with ''SCSI and RAID Host Controller'. However, when checking out the old version of Windows XP, I found 'SCSI and RAID Host Controller'
is there. (Screen shot below)
The new Windows XP(32Bit) SP3, there is no 'SCSI and RAID Host Controller'
My motherboard is:
My Desktop Computer(Intel P 4, 512MB of RAM, and Graphics Card with 256MB of RAM.
]I am seeing that most computer doesn't has the scsi / raid controller . in the old Windows XP on my computer that SCSI and RAID controller exists, and it it has not a yellow mark on it.
When I installed a new windwos XP 32Bit SP3, no SCSI/RAID in divice manager .
My computer sound on new Windows XP doesn't work , however, on old Windows XP SP2 works well. I have a buitl-in sound card. SCSI and RAID controller category in the device manager on the old Windows xp SP2 is realted to sound card,I don't think.
Thus, What drivers would let the 'SCSI and RAID Host Controller' added in the device manager?
A man should convert his anger and sadness into strength to continue living in this life.If you open the case and shine a light on the motherboard you can usually see both the manufacturers name and the model printed on the pcb somewhere. You should also normally see this information on the first POST screen when you turn on the PC.
Otherwise Google "775i65G" like I did.
Here are the driver downloads (assuming it is an Asrock 775i65G R2.0 and not an R3.0)
http://www.asrock.com/mb/Intel/775i65G%20R2.0/?cat=Download&os=XP
You should install the inf driver first. Hopefully after you do that you will see your desired listing in Device Manager.
With regard to the AMR driver and the HDMR driver, you can find some information about these here :
http://en.wikipedia.org/wiki/Audio/modem_riser
Unless you actually have something plugged into these risers, it is probably not necessary to install the drivers.
However, the drivers for the integrated C-Media audio chip and the Realtek Lan chip may prove useful.
It looks like the motherboard has integrated video but if you are using a graphics card it will not normally be necessary to install the VGA driver.
You can download both the manual and the installation guide here
http://www.asrock.com/mb/Intel/775i65G/?cat=Manual
And if "SCSI and RAID Host Controller" is still not shown in Device Manager, don't worry - because these functions are not supported by your motherboard (again assuming it is an Asrock 775i65G)
Thanks a lot,
First of all, when saying that I have multi-operationgs systems, I mean there are two operating systems installed on my PC(SP2, SP3) both are 32Bit. The first Windows SP2(NOT installed by me) has all multimedia audio card installed
well, and has SCSI and RAID Host Controller shown the device manager. However, only the VGA is not installed on Windows SP2. However, the second one Windows SP3(Installed by me) has VGA not installed, Multimedia audio NOT installed, and there is no SCSI and
RAID Host Controller in device manager.
First: Why did the CPUz, specy didn't detect motherboard name, and only detect the model. IF I need to open the case and shine a light on the motherboard you can usually see both the manufacturers name and the model printed on
the pcb somewhere, then what benfit would be there from hardware detection software?
Second: Yes, my motherboard has integrated video, and integrated audio card
However, this doesn't mean that I don't need to install them since the Vidoe controller is not properly installed (it is a default VGA ) Also, Multimedia audio controller is not functiong at all.
Finally: if And if "SCSI and RAID Host Controller" is still not shown in Device Manager in Windows XP SP3, because these functions are not supported by my motherboard, then why is 'SCSI and RAID Host
Controller' installed/shown in the device manger in Windows XP SP2 on the same PC???
A man should convert his anger and sadness into strength to continue living in this life. -
Satellite P10-504 WXP driver for video, modem and SM bus controller
I have just had to replace the hard disk in my P10-504 and I now have lots of problems!
1 - I used the retore disks and XP home is installed BUT the video, modem and SM bus controller all all flagged in Control Panel and not having drivers installed! The modem I can live without but I would like the video to work properly and the SM bus controller is also pretty essentil. Guess what, I can't
a) find my model listed on the Toshiba website and
b) I can't find drivers for either the video or SM bus controller.
I have downloaded the 'universal' Nvidia driver but it doesn't work! As for the SM bus controller, I've no idea where to look!
Any ideas please?
Thanks
TimHi
Your posting is a little surprise because all XP drivers for your notebook must be available on the Toshiba driver page.
Did you choose the right notebook series and did you download and install all necessary drivers???
As first its important to install the chipset utility and depending on installed graphic card
You have to choose and to install the right display driver!
Again! The drivers are on the page!
http://eu.computers.toshiba-europe.com -> Support & Downloads -> Support page -> driver download -
802.1x and Windows Domain Controller with ACS
Wow, I am having a tough time getting my ACS and the Domain controller to work with 802.1x PEAP. Can somebody explane to me how to set up the domain controller (Active directry) to get a PEAP cert? Some other questions. If I am using PEAP and 802.1x how does my computer get a cert. from the CA if the port is disabled by 802.1x? And How do I set up my domain controller to work with ACS to authenticate users. I have been beating my self to death to figure this out. Any help would be ausome. I am really stuck on trying to make this work.
Thanks a ton in advance
JustinI as a Cisco customer would like to see answers to our questions based on some real world experience or something you've noticed in a lab environment.
By simply posting links is not very helpful. The reason most of us come to this site and post our questions, is because we already went to the Cisco website and found the explanation to be vague. In the future, please post answers to our question, intead of referring us to a link.
Thank you,
John... -
Can we run domain controller windows 2008 32 bit and additional domain controller on 2003 server
im my environment we are trying to upgrade from server 2k3 to 2k8, out testing done on server 2k3 to 2k8, but can we run domain controller windows 2008 32 bit and additional domain controller on 2003 server ...kindly suggest
Nitin Gaurav
[email protected]Yes you can. If you have two 2003 AD servers currently and upgrade one of them to 2008 AD then they'll continue to be able to work together. The domains functional level will remain as 2003 across both servers so at this stage you won't get any benefit from
the new AD functionality available in 2008.
Once you've then upgraded the second 2003 server to 2008 you can then upgrade the functionality levels in AD to make it 2008. It's been a while, but I believe it doesn't happen automatically, so once all AD servers have been upgraded you have to go into
AD and upgrade the functionality levels yourself. -
Disabling Mirrored cache AND/OR Redundant Controller in STK 2540
Hi,
We have a dual controller STK 2540. Wanted to know if there is a way to disable cache mirroring (also called cache synchronization)? This is to test the impact of 1/3 loss of performance when cache is mirrored to protect cached data in the event of controller failure in a dual-active controller configuration.
I searched thorugh entire CAM and could not find an option.
Also would like to know how to confirm whether the controller is in redundant mode or Active-Passive mode. CAM does not show this as well.
Is CLI the only option to view/modify the above mentioned configuration? If so, please let me know what command should we use to view and modify the same.
Thanks.RW_DB_Arch wrote:
Thanks nwi.
I have seen the 'Active' status for both controllers from the CAM interface as well from the sscs output. That is fine, but I think I did not put across my question very correctly.
According to my understanding, if the cache is mirrored/synchronized then it will impose an approx. 33% of performance degradation. And I want to do away with that. So,
I want to view the redundancy mode of controllers i.e. whether they are running in non-redundant mode or redundant mode. In either mode, both will be active.
I also want to view the mirroring mode of the cache i.e. whether the cache is mirrored or not mirrored. In either mode, full 1Gb cache will be used.
The controller will always be in redundant mode, you cannot change this. They will be active/active, if any controller is passive this means that it doesn't service I/O and the volumes won't failover in case there is a problem with the active one.
You can however disable the cache mirroring between both controllers, that said, this is something we really do not recommend to do. Imagine you disable the mirroring, now one controller reboots (because this is something that may happen as per design to protect the data in specific situations), you will lose the data in the cache for this controller, this is the data which is not flushed to the drives.
And then I want to achieve the foll. configuration:
2 controllers, both active, but in non-redundant mode.You cannot do that. With the ST2500 like the ST6000 the controller are redundant each other.
Which also means that cache mirroring/synchronization is off. So something like this: 2 volumes - vol1 has Controller A as the owning/preferred controller and vol2 has Controller B as the
owning/preferred controller. Since controller redundancy is off, I believe, if 1 of the controller fails then the volume cannot be accessed via the surviving controller (i.e. no failover to the surviving
controller) and I am fine with it. But I will get better performance because of the non-mirroring mode of cache.Such non redundant configuration isn't supported with those arrays.
Regards
>
Pls. advice.
Thanks. -
Satellite L30-114 - Need driver for sound and SM bus controller
Hi, friends
Plz I need your help on my Satellite L30-114. Am having problems with the sound and the SM bus controller, even I have downloaded the sound driver and install it, from my device manager sound is not sick, it always telling me my device is working properly? Plz i need help on that.
Secondly my SM bus controller is sick it has the cormer sign plz how can I rectify it, even my wireless is working fine.
Only the sound and sm bus controller is giving problems.
Thanks will be waiting for your replies.
newtonHi
To be honest I doubt that you have installed all files from the Toshiba website. Normally the Toshiba website contains all drivers and tools that you need to restore factory settings after this there are no more yellow exclamation marks or unknown devices in device manager.
By the way: What installation order you have used?
On the Toshiba website you can find the installation instructions document. This is a list for the recommended driver installation order.
Check this!!! -
Unable to telnet and tftp to controller
hello experts!!!
5508 controller is at the headquarters which can be normally pinged, telnetted, http'd and tftp'ed....
at the remote site, controller can be pinged and http'ed but cannot be telnetted and tftp'ed.
there is a complete tracert from the remote site pc all the way to the controller.
from a switch at a remote site, the controller can be telnetted.
but from a pc on the remote site (which belongs to a remote site vlan), it is unable to telnet and tftp the controller.
all active components can be telnetted from the remote site, such as the core switches and routers at the headquearters, except the controller.
upgraded the controller code to 7.2.xxx in headquarters but still unable to telnet and tftp the controller from remote site.
is there any more settings on the controller for telnet and tftp?
what could be the problem why the controller is not available for telnet and tftp from the remote site?
thank you, experts, in advance for your replies!!!Hello, Leo!
See output of the command:
(Cisco Controller) >show network summary
RF-Network Name............................. GID2012
Web Mode.................................... Enable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Enable
OCSP........................................ Disabled
OCSP responder URL..........................
Secure Shell (ssh).......................... Enable
Telnet...................................... Enable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
AP Multicast/Broadcast Mode................. Unicast
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
IGMP Query Interval......................... 20 seconds
MLD snooping................................ Disabled
MLD timeout................................. 60 seconds
MLD query interval.......................... 20 seconds
User Idle Timeout........................... 28800 seconds
ARP Idle Timeout............................ 300 seconds
Cisco AP Default Master..................... Enabled
--More-- or (q)uit
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Enable
Mgmt Via Dynamic Interface.................. Enable
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
AP Fallback ................................ Enable
Web Auth Redirect Ports .................... 80
Web Auth Proxy Redirect ................... Disable
Web Auth Captive-Bypass .................. Disable
Web Auth Secure Web ....................... Enable
Fast SSID Change ........................... Disabled
AP Discovery - NAT IP Only ................. Enabled
IP/MAC Addr Binding Check .................. Enabled
CCX-lite status ............................ Disable
oeap-600 dual-rlan-ports ................... Disable
oeap-600 local-network ..................... Enable -
Satellite c885d-s5202 Laptop Device USB2.0-CRW AND MS Bus Controller
I need how for issued my Satellite c885d-s5202 Laptop Device Usb2.0-CRW AND MS Bus Controller Troubleshoothing update error massage displayed : Windown could not fin driver software for device. Also I tried download Toshiba driver update ready install but not working correctly....error massage Deteted Incampable ..Please help me ...thank you ...Have a nice day!
If you can't solve your issue and no one in the community can help, contact support to speak with a tech support agent at (800) 457-7777.
- Peter -
[915 Series] Ethernet Controller and SM Bus Controller Drivers
I have a 915P Neo2 Platinum Motherboard.
I recently built a computer. When I put the driver CD in my computer freezes on loading. I have trieed finding the source of that problem. Now I am trying to Download the drivers. I have downloaded most but the two Question mark thingos it says on my device manager list are "Ethernet Controller" and "SM Bus controller". I have searched on the driver download list. I can find the right ethernet controller but when I download the zipped folder and unzip it, it just has a few random files that I cant open. No setup files. How do i use these files?Hi Adams.. first we need your sys specsQuote
-CPU speed, FSB speed and OC speed which you always run if you OC, also include whether HT is enabled or not.
-RAM, the timing and the OC timing which you always run,
-exact motherboard model,
-display card, if u OC include the info as well
-PSU, power supply unit, brand and model, even better to include the exact wattage of all +3.3V, +5V and 12V rails
-HDDs, CDROMs and which ports you plug them in
-other PCI cards and which slots you plug them in
-other peripherals like USB, 1394 devices which you plug them in and create the issue
-BIOS settings which you changed from the default values, such as enable/disable some built-in devices, ACPI, etc
-OS, with service pack -
Driver needed for PCI Data Acquisition and Signal Processing Controller of HP 15- r247tu
Install the Windows 10 Intel IMEI Intel Management Engine Interface (MEI) Driverhttp://ftp.hp.com/pub/softpaq/sp69501-70000/sp69593.exe The latest version of the Intel chipset driverhttp://ftp.hp.com/pub/softpaq/sp69501-70000/sp69575.exe All Windows 10 drivers available from HP are at the following link.http://support.hp.com/us-en/drivers/selfservice/HP-15-Notebook-PC-series/7486447/model/7693973#Z7_3054ICK0KGTE30AQO5O3KA30R1
Hi: Try the chipset driver directly from Intel...the second file is the auto install file. https://downloadcenter.intel.com/download/20775/Intel-Chipset-Device-Software-INF-Update-Utility- If that driver does not install the PCI Data Acquisition and Signal Processing Controller, which the chipset driver should install, download the first file listed above (zip file). Unzip and extract the contents to its folder. Go to the device manager and click on the above device needing the driver. Click on the driver tab. Click on Update driver. Select the Browse my computer for driver software option, and browse to the unzipped driver folder. Make sure the Include Subfolders box is checked, and see if the driver installs that way. Then reboot.
Maybe you are looking for
-
Iphone 5 went black. Tried pushing on/off and circle at the same time. Worked yesterday and then did it again today. Can't get it to work.
-
Problem starting weblogic server
Can I use third party libraries with the evaluation copy of the weblogic server? I am having problems starting the weblogic server with third party libraries (i.e. oralce's sqlj's translator.zip, runtime.zip and classes2.zip). The following exception
-
My phone is stuck in headphone mode! how to fix this?
-
hi all how to use existing purchase order smart form...whats the name and whats the print program for that. rgds anu
-
Safari New Tabs vs. New Window
when i use safari on any computer weather it be a Mac or a PC, Safari doesn't allow me to click on a link and it open in a new tab. I know that you can go into preferences/general tab, and at the bottom select open links in new tab or window. I've do