Newbie Help with N8 Gps

hi guys. first post....
I bought a nokia n8 from a local store. it is a second hand unit. i am from south africa.
So, when i turned on the phone, i saw the operator logo "3" So I assume the phone was bought outside my country.. Anyway, the phone works fine.... Then i tried the gps functionlity of the phone.
i cannot get a lock on my position. I tried a few things suggested on this site. I tried: soft reset, changed the position server form "supl.nokia.com" to "supl.google.com", deleted "supl.nokia.com" access point, switched off agps, network and switched it back on and also i downloaded an app "legps" but my gps still don't function.
Here's the deal. When I switch on the internal gps, agps, then i get no lock. it searches forever. When I select "network" only, I get the message "My position within 300m" But when I turn on the intergrated, apgps with network, then i get the message "My position within 300m" So I assume when "network" is selected, my cell phone operator assist in getting my position. But my internal gps is not working... So I think it could be the fact that it it's not accessing the correct server? Cause I deleted the supl.nokia.com server. Tried to add it again but couldnt add an access point in the positioning server. Shouldnt of deleted it in the first place.....
The only thing I can think of is changing the server. Here's another thing. When I set the phone to ofline mode, and then go to position server settings, I see another server appearing with the this line:
h slp mnc001.mcc655.pub.3gppnetwork.org. But when I activate "general" profile again, then that server disappear. I guess it has something to do with the country server settings?
I don't know what to do. please help.
Regards

hi. sorry for the delayed reply.... timezones.. anyway i tried downloading the software to reinstall on my phone but couldnt cause of internet problems.. So i searched the net and i came across this:
This is really great news for those with NOKIA 5800.
I have no idea if it works at all locations / country / are, but does not prevent you to try.
As we all know GPS on our phones is a tragedy at the time of the hooks on the TV, I personally wanted to disengage while hooked and want out.
And now I've found that in my opinion, really:
Go to: Settings / Phone / Application / Settings / Positioning / Positioning Server / Server Address
and the possibility that the "Positioning Server" - "supl.nokia.com"
with this: "h-slp.mnc015.mcc234.pub.3gppnetwork.org"
MCC MNC
214 01 Vodafone Vodafone Spain Operational GSM 900 / GSM 1800 / UMTS 2100
"H-slp.mnc001.mcc214.pub.3gppnetwork.org"
214 03 Orange France Telecom Spain SA Operational GSM 900 / GSM 1800 / UMTS 2100
"H-slp.mnc003.mcc214.pub.3gppnetwork.org"
214 04 Telstra Xfera Moviles SA Operational UMTS 2100
"H-slp.mnc004.mcc214.pub.3gppnetwork.org"
214 TME 05 Telefónica Móviles Spain Operational GSM 900 / GSM 1800 / UMTS 2100 Used by resellers
"H-slp.mnc005.mcc214.pub.3gppnetwork.org"
214 06 Vodafone Vodafone Spain Operational GSM 900 / GSM 1800 / UMTS 2100 Used by resellers
"H-slp.mnc006.mcc214.pub.3gppnetwork.org"
214 07 movistar Telefónica Móviles Spain Operational GSM 900 / GSM 1800 / UMTS 2100
"H-slp.mnc007.mcc214.pub.3gppnetwork.org"
Then restart your phone, it is desirable.
We also advise you to copy the old / supl.nokia.com / note address somewhere to have it in your phone
It is copied from a site which was translated through google...I think if i can add a south african server in server settings then maybe it can work? regards

Similar Messages

I need urgent help with the GPS

i've ask my family to buy Nokia n 97 from syria,while i live in cyprus,how ever i got the phone with a card inside the box says:
this nokia device has been specially designed and manufactured for this market.the satandard GPS features have been disabled in accordance with market regulations.
im using this mobile for the second day,i can't send it back to syria and i don't know what to do,i can't connect with the gps system in cyprus and i can't connect with the internet,please help me to find a way to enable the GPS system in my phone.
THanks a lot

As I explained in an earlier post, you WILL NOT be able to do it yourself.
If the hardware is just disabled (the error message may be misleading), a Nokia service point may be able to reactivate it, though you'd have to pay because the phone only has warranty in Syria and because this wouldn't be a warranty fix anyway.
If the hardware is removed, then you are more than likely stuck.

Newbie - help with homework.

Create a procedure to insert a record into the Bill_Items table. All the fields in the Bill_Items table will be specified as para with the exception of the Selling_Price, which will be the Current_Price, retrieved from the Menu_Items table. Do not allow the insert to finish unless there are enough of all ingredients on hand. If the insert is successfull, the quantity field in the Ingredient table will need to be updated accordingly.
Tables are below.
Thanks,
CREATE TABLE Bill_Items
Bill_Number NUMBER(6,0)
CONSTRAINT FK_Bill_Items_Bill_Number REFERENCES Bills(Bill_Number)
CONSTRAINT NN_Bill_Items_Bill_Number NOT NULL,
Menu_Item_Number NUMBER(5,0)
CONSTRAINT FK_Menu_Item_Num REFERENCES Menu_Items(Menu_Item_Number)
CONSTRAINT NN_Bill_Items_Menu_Item_Num NOT NULL,
Discount NUMBER(5,2)
CONSTRAINT N_Bill_Items_Discount NULL,
Quantity NUMBER(3,0) DEFAULT 1
CONSTRAINT Bills_Items_Quanity_CC CHECK(Quantity > 0)
CONSTRAINT NN_Bill_Items_Quantity NOT NULL,
Selling_Price NUMBER(6,2) DEFAULT 0
CONSTRAINT Bills_Items_SellingPrice_CC CHECK(Selling_Price >= 0)
CONSTRAINT NN_Bill_Items_Selling_Price NOT NULL,
CONSTRAINT PK_Bill_Items PRIMARY KEY(Bill_Number,Menu_Item_Number)
CREATE TABLE Menu_Item_Ingredients
Menu_Item_Number NUMBER(5,0)
CONSTRAINT FK_Menu_Item_Ing_Menu_Item_Num REFERENCES Menu_Items(Menu_Item_Number)
CONSTRAINT NN_Menu_Item_Ing_Meun_Item_Num NOT NULL,
Ingredient_Number NUMBER(5,0)
CONSTRAINT FK_Menu_Item_Ing_IngredientNo REFERENCES Ingredients(Ingredient_Number)
CONSTRAINT NN_Menu_Item_Ing_IngredientNo NOT NULL,
Quantity NUMBER(5,2) DEFAULT 1
CONSTRAINT Menu_Item_Ing_Quanity_CC CHECK(Quantity > 0)
CONSTRAINT NN_Menu_Item_Ing_Quanity NOT NULL,
Constraint PK_Menu_Item_Ing PRIMARY KEY(Menu_Item_Number, Ingredient_Number)
CREATE TABLE Ingredients
Ingredient_Number Number(5,0)
CONSTRAINT PK_Ingredients_IngredientNo PRIMARY KEY
CONSTRAINT NN_Ingredients_IngredientNo NOT NULL,
Ingredient_Name VarChar2(35)
CONSTRAINT NN_Ingredients_Ingredient_Name NOT NULL,
Portion_Code CHAR(2)
CONSTRAINT FK_Ingredients_PortionCode REFERENCES Portions(Portion_Code)
CONSTRAINT NN_Ingredients_PortionCode NOT NULL
REFERENCES Portions(Portion_Code),
On_Hand NUMBER(6,2) DEFAULT 1
CONSTRAINT Ingredients_OnHand_CC CHECK(On_Hand > 0)
CONSTRAINT NN_Ingredients_On_Hand NOT NULL,
Reorder_Point NUMBER(6,2) DEFAULT 1
CONSTRAINT Ingredients_Reorder_Point CHECK(Reorder_Point > 0)
CONSTRAINT NN_Ingredients_Reorder_Point NOT NULL,
Current_Cost NUMBER(5,2) DEFAULT 0
CONSTRAINT Ingredients_CurrentCost_CC CHECK(Current_Cost >= 0)
CONSTRAINT NN_Ingredients_Current_Cost NOT NULL
CREATE TABLE Menu_Items
Menu_Item_Number NUMBER(5,0)
CONSTRAINT PK_Menu_Items_MenuItemsNo PRIMARY KEY
CONSTRAINT NN_Menu_Items_MenuItemsNo NOT NULL,
Menu_Item_Name VARCHAR2(50)
CONSTRAINT NN_Menu_Items_Menu_Item_Name NOT NULL,
Current_Price NUMBER(6,2) DEFAULT 0
CONSTRAINT Menu_Items_CurrentPrice CHECK(Current_Price >=0)
CONSTRAINT NN_Menu_Items_Current_Price NOT NULL,
Production_Cost NUMBER(6,2) DEFAULT 0
CONSTRAINT Menu_Items_ProdCost CHECK(Production_Cost >=0)
CONSTRAINT NN_Menu_Items_Production_Cost NOT NULL
);

Newbie to oracle - help with homework.. Letting others do your work is called cheating, where I live.
C.

Newbie: help with join in a select query

Hi: I need some help with creating a select statement.
I have two tables t1 (fields: id, time, cost, t2id) and t2 (fields: id, time, cost). t2id from t1 is the primary key in t2. I want a single select statement to list all time and cost from both t1 and t2. I think I need to use join but can't seem to figure it out even after going through some tutorials.
Thanks in advance.
Ray

t1 has following records
pkid, time, cost,product
1,123456,34,801
2,123457,20,802
3,345678,40,801
t2 has the following records
id,productid,time,cost
1,801,4356789,12
2,801,4356790,1
3,802,9845679,100
4,801,9345614,12
I want a query that will print following from t1 (time and cost for records that have product=801)
123456,34
345678,40
followed by following from t2 (time and cost for records that have productid=801)
4356789,12
4356790,1
9345614,12
Is this possible?
Thanks
ray

Newbie - Help With templates

I am fairly new to dreamweaver. Looking to put together a
basic site for a holiday home for rent. Would like to include
photos of the house and surrounding area, travel details, details
of things to do and see, calendar, temeperature charts etc. Can
anyone suggest where I can get my hands on templates that would
help with this?
Many thanks

The best I've seen are from ProjectSeven -
http://www.projectseven.com/
They are commercial (look at the Page Packs) and they are
excellent.
Murray --- ICQ 71997575
Adobe Community Expert
(If you *MUST* email me, don't LAUGH when you do so!)
==================
http://www.projectseven.com/go
- DW FAQs, Tutorials & Resources
http://www.dwfaq.com - DW FAQs,
Tutorials & Resources
==================
"Gusley5" <[email protected]> wrote in
message
news:[email protected]...
>I guess sources for templates is what I'm looking for.
I've little
>knowledge
> of writing code so was looking for a draft template
which would have a
> professional look to it with regard to font, layout,
colours, buttons to
> use
> for links etc. I suppose some sort of table layout for
including photos
> with
> related text may be best place to start.
>
> Code below is from a starter page available from
dreamweaver. Any other
> suggestions for templates gratefully received.
>
> Thanks
>
> <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0
Transitional//EN"
> "
http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd">
> <html xmlns="
http://www.w3.org/1999/xhtml">
> 
> <head>
> 
> <title>Lodging - Catalog</title>
> <meta http-equiv="Content-Type" content="text/html;
charset=iso-8859-1" />
> <link rel="stylesheet"
>
href="file:///C|/Program%20Files/Macromedia/Dreamweaver%208/Configuration/BuiltI
> n/StarterPages/mm_lodging1.css" type="text/css" />
> </head>
> <body bgcolor="#999966">
> <table width="100%" border="0" cellspacing="0"
cellpadding="0">
> <tr>
> <td width="15"
nowrap="nowrap"> </td>
> <td height="60" colspan="2" class="logo"
nowrap="nowrap"><br />
> WEBSITE NAME HERE</td>
> <td width="100%"> </td>
> </tr>
>
> <tr bgcolor="#ffffff">
> <td colspan="4"><img
>
src="file:///C|/Program%20Files/Macromedia/Dreamweaver%208/Configuration/BuiltIn
> /StarterPages/mm_spacer.gif" alt="" width="1" height="1"
border="0"
> /></td>
> </tr>
>
> <tr bgcolor="#a4c2c2">
> <td width="15"
nowrap="nowrap"> </td>
> <td height="36" id="navigation"
class="navText"><a
> href="javascript:;">HOME</a></td>
> <td> </td>
> <td width="100%"> </td>
> </tr>
>
> <tr bgcolor="#ffffff">
> <td colspan="4"><img
>
src="file:///C|/Program%20Files/Macromedia/Dreamweaver%208/Configuration/BuiltIn
> /StarterPages/mm_spacer.gif" alt="" width="1" height="1"
border="0"
> /></td>
> </tr>
>
> <tr bgcolor="#ffffff">
> <td valign="top" width="15"><img
>
src="file:///C|/Program%20Files/Macromedia/Dreamweaver%208/Configuration/BuiltIn
> /StarterPages/mm_spacer.gif" alt="" width="15"
height="1" border="0"
> /></td>
> <td valign="top" width="35"><img
>
src="file:///C|/Program%20Files/Macromedia/Dreamweaver%208/Configuration/BuiltIn
> /StarterPages/mm_spacer.gif" alt="" width="35"
height="1" border="0"
> /></td>
> <td width="710" valign="top"><br />
> <table border="0" cellspacing="0" cellpadding="2"
width="610">
> <tr>
> <td colspan="7" class="pageName">Page Name
Here</td>
> </tr>
> <tr>
> <td width="22%" height="110"><img
>
src="file:///C|/Program%20Files/Macromedia/Dreamweaver%208/Configuration/BuiltIn
> /StarterPages/mm_product_sm.gif" alt="small product
photo" width="110"
> height="110" border="0" /></td>
> <td> </td>
> <td width="22%" height="110"><img
>
src="file:///C|/Program%20Files/Macromedia/Dreamweaver%208/Configuration/BuiltIn
> /StarterPages/mm_product_sm.gif" alt="small product
photo" width="110"
> height="110" border="0" /></td>
> <td> </td>
> <td width="22%" height="110"><img
>
src="file:///C|/Program%20Files/Macromedia/Dreamweaver%208/Configuration/BuiltIn
> /StarterPages/mm_product_sm.gif" alt="small product
photo" width="110"
> height="110" border="0" /></td>
> <td> </td>
> <td width="22%" height="110"><img
>
src="file:///C|/Program%20Files/Macromedia/Dreamweaver%208/Configuration/BuiltIn
> /StarterPages/mm_product_sm.gif" alt="small product
photo" width="110"
> height="110" border="0" /></td>
> </tr>
> <tr>
> <td valign="top" class="calendarText"
nowrap="nowrap"><a
> href="javascript:;">Product Name</a><br
/>
> Price: $0.00</td>
> <td> </td>
> <td valign="top" class="calendarText"
nowrap="nowrap"><a
> href="javascript:;">Product Name</a><br
/>
> Price: $0.00</td>
> <td> </td>
> <td valign="top" class="calendarText"
nowrap="nowrap"><a
> href="javascript:;">Product Name</a><br
/>
> Price: $0.00</td>
> <td> </td>
> <td valign="top" class="calendarText"
nowrap="nowrap"><a
> href="javascript:;">Product Name</a><br
/>
> Price: $0.00</td>
> </tr>
> <tr>
> <td colspan="7"> </td>
> </tr>
> <tr>
> <td height="110"><img
>
src="file:///C|/Program%20Files/Macromedia/Dreamweaver%208/Configuration/BuiltIn
> /StarterPages/mm_product_sm.gif" alt="small product
photo" width="110"
> height="110" border="0" /></td>
> <td> </td>
> <td height="110"><img
>
src="file:///C|/Program%20Files/Macromedia/Dreamweaver%208/Configuration/BuiltIn
> /StarterPages/mm_product_sm.gif" alt="small product
photo" width="110"
> height="110" border="0" /></td>
> <td> </td>
> <td height="110"><img
>
src="file:///C|/Program%20Files/Macromedia/Dreamweaver%208/Configuration/BuiltIn
> /StarterPages/mm_product_sm.gif" alt="small product
photo" width="110"
> height="110" border="0" /></td>
> <td> </td>
> <td height="110"><img
>
src="file:///C|/Program%20Files/Macromedia/Dreamweaver%208/Configuration/BuiltIn
> /StarterPages/mm_product_sm.gif" alt="small product
photo" width="110"
> height="110" border="0" /></td>
> </tr>
> <tr>
> <td valign="top" class="calendarText"
nowrap="nowrap"><a
> href="javascript:;">Product Name</a><br
/>
> Price: $0.00</td>
> <td> </td>
> <td valign="top" class="calendarText"
nowrap="nowrap"><a
> href="javascript:;">Product Name</a><br
/>
> Price: $0.00</td>
> <td> </td>
> <td valign="top" class="calendarText"
nowrap="nowrap"><a
> href="javascript:;">Product Name</a><br
/>
> Price: $0.00</td>
> <td> </td>
> <td valign="top" class="calendarText"
nowrap="nowrap"><a
> href="javascript:;">Product Name</a><br
/>
> Price: $0.00</td>
> </tr>
> <tr>
> <td colspan="7"> </td>
> </tr>
> </table> </td>
> <td> </td>
> </tr>
>
> <tr>
> <td width="15"> </td>
> <td width="35"> </td>
> <td width="710"> </td>
> <td width="100%"> </td>
> </tr>
> </table>
> </body>
> </html>
>

Newbie - Help with Fireworks CS5 nav bar

I am new to Fireworks. I am using Fireworks CS5. I need help with creating navigation bars and menu. Any tutorial or tips is greatly appreciated.
Thank you.

You'll find a tutorial named "Create a basic navigation bar" in the Fireworks help files.

Help with superstar2 GPS receiver

hello every1,
I have a superstar2 gps receiver...I am trying to get the binary data
into LABVIEW 8...but I get only junk characters(encoded binary) into
labview..when I run the simple read and write binary.vi file....But if
I rightclick on the read binary file then I get to choose the
hexadecimal option...the readings are in hex form ..but how do I get
binary format...

hello every1,
Thanx for replying...I tried using the below attached files which were found on that particular link..and it worked fine...but I want to get this data into graph plotting format(i.e in the form of X,Y and Z format).It would be great if some1 could help me out with this issue..
-thanx
innovator81
Attachments:
GPS.llb ‏488 KB
Garmin Comms.llb ‏140 KB
Get RMC_GGA.llb ‏164 KB

I need some help with my GPS issue

I'm writing to ask you if You could somehow help me solve my GPS issue. I own Nokia 5800 XpressMusic. I've recently updated it's software and installed the new OVI Maps. I know that there is an option to use it offline which means without an Internet connection. When I start the Maps application and choose the offline mode, the only thing that appears at the top of the screen is "Searching position". The map is available but my position can't be specified without Internet on. When I turn my wireless router on, even though my maps are set in offline mode, it automatically connects to the Internet and spends something like 5KB download. If I keep navigating it spends even more. I've left my mobile phone offline to search for my position for an about half an hour but nothing happened. So, my question is, could you tell me what to do and how to use OVI Maps offline?

Assuming you are useing Maps 3.06 from beta labs and the map data is the latest compatible maps installed through ovi suite, then all should work well provided you followed the installation instructions correctly. If you don't use assisted gps or any other method of positioning except integrated Gps then you need to be in an open space with clear view of the sky to allow the GPS antenna to get a lock, this can take 10 to 30 minutes (the first time you try for a lock, shouldn't take that long again) and once you have a lock the location should work fine. The reason the other methods are available is thet they speed up the whole process and also work when in built up areas where buildings can block thre satelite view from the gps antenna. The amount of data used to lock your position is minimal and unless you have zero data allowance I suggest using all the positioning methods. If using the navigation abroad, you can disable evrything and simply use integrated GPS as long as you've loaded the local map data to your phone previously.
Good Luck
If I have helped at all, a click on the White Star is always appreciated :
you can also help others by marking 'accept as solution'

Newbie Help with videocameras and editing software

I am a third grade teacher who can whip around in imovie pretty well, but I want to expand and post training videos to the web. I also want to vodcast. I need a relatively easy videocamera, and of course, reasonably priced. I don't understand all the mumbo jumbo about the dvd, tape, flash videocameras except to know that some are not compatible with osx.
Also would I be better off with Final Cut Pro Express?
Help to a newbie...

susannamessier wrote:
OK now I am looking and I want this camera to be compatible with imovie also. On the Apple support page along side the Canon's I am looking at I see:
Video stabilization limitations more...
Filming in Cinema or 24p mode more...
What? Goodness could this be anymore complicated?
It's very intimidating at first. The short answer is that all this is compatible with iMovie.
The longer one is:
The number refers to frames per second (frame rate, in the jargon). Cine cameras run at 24 frames per second, so 24 fps is considered to give a look to moving objects similar to what you'd see in a filmed movie (think wagon wheels appearing to go backwards in old westerns).
p refers to progressive, and means that you're getting 24 complete frames each second - again like film (this idea of mimicking film is the holy grail to some video makers - I say video is video, and should be treated like video). The opposite of progressive is i, for interlaced. Interlacing is a technique used in television since the early days as a way of giving you a better looking TV picture; in interlacing, instead of looking at each frame as a whole, you split it into very narrow lines, then scan al the odd ones, followed by all the even ones. In the old days, the scanning had to be linked to the way in which the electricity supply worked, so scanning was based on a frequency of 60 cycles per second (in the USA).
So in video, you will see camcorders offering a frame rate of 60i as standard - i.e. 60 interlaced frames in one second.. They usually also offer 30p (which combines the results of 2 60i scans to give you 30 complete frames. And then as you've seen, 24p so you can make it look like film.
You can shoot good movies in any of those frame rates; which ones you choose are up to you, but they're all used by many people for many different purposes. Some people will tell you you must use frame rate x for subject y. Listen, but don't follow blindly - try it out and see what works for you.
The issue you will sometimes here debated about iMovie is how to take video you have shot interlaced, and get iMovie to export it as progressive, but still in high quality. Don't worry about that right now.
Just get a camcorder you like, and make some movies. First feel really proud of them, then learn some more, and feel embarrassed by them (this is what we all do!).
Hope that helps.

Newbie help with editing files in DW CS3

I am new to using Dreamweaver, and I am having trouble with
trying to edit existing files using DW CS3. When I open an existing
file on my local site, DW converts some of the code using &.
This is a problem because I need to edit the file just as it was
originally written, so I can save it after editing and upload to my
website.
In my Preferences, I have Code Rewriting set to:
-Rewrite Code: Fix invalidly nexted and unclosed tags
[Unchecked]
-Rewrite Code: Rename form items when posting [Checked]
-Rewrite Code: Remove extra closing tags [Unchecked]
-Never rewrite code: In files with extensions .as .asr .asc
.asp .ascx .asmx .aspx .cfc .cfm .cfml .config .cs .ihtml .js .jsp
.php .php3 .vb .xml .xsl .xslt .xul
-Special characters: Encode <, >, &, and " in
attribute values using & [Unchecked]
-URL encoding: Do not encode special characters
-Active Content: Insert using browser-safe scripts [Checked
by default]
-Active Content: Convert tags to scripts on file open
[Unchecked]
Today, I opened a file with an .xml extension, and DW rewrote
the special characters > and '. Since I have in my preferences
to Never rewrite code in .xml, I don't understand why DW is
rewriting the code. Also, in my preferences I have unchecked the
Special Characters, so why is DW still rewriting the code?
Do I have some of the Code Rewriting preferences set wrong?
Is there another place I need to tell DW not to rewrite
existing code?
Thanks for your help!
Cyndi

It imported both, but only shows you the raw file. Ever. What you see and what you edit will only be the raw file. The associated JPG file will follow the raw file around if you move it or rename it using Lightroom, but other than that, Lightroom will ignore it. You could safely delete the JPG, and Lightroom wouldn't complain--probably wouldn't even notice.
There's a preference you can set that will cause JPGs to be imported as separate images. Then you'd be able to see both of them and edit them separately. That preference won't take effect on images that are already in the catalogue, but will affect all future imports.
Hal

JSF Newbie: help with forms & drop-downs

Hi,
I've managed to get a few simple things working with JSF using Netbeans & Visual Web pack. This is pretty sexy stuff for a grizzled old perl programmer. However, there are still a few things I'm having trouble getting through my thick head -- maybe some kind soul could point me in the right direction.
I would like to have a couple of cascading data-bound drop-downs: dd1 provides a selection list for dd2, and the combination of dd1 and dd2, when selected, provides enough data to populate a webuijsf:table.
The desired behaviour is that a change in dd1 repopulates the selection list for dd2 and furthermore, repopulates the table based on the selected value in dd1 plus the first value in the selection list of dd2. A change of selection in dd2 repopulates the table accordingly.
My prerender() for the page checks if dd1.getSelected == null, and if so, sets the cursor to the first row in the bound data provider. Furthermore, it primes the rowset for dd2 with some rows from dd2's data provider based on the values in the first row for dd1.
The first time through, everything is peachy: dd1 has the appropriate selection list, as does dd2. my webuijsf:table also has the appropriate rows (selected in the prerender()).
My problem seems to be that when a new value is selected in dd2, dd1.getSelected == null at the next prerender(). This, of course, re-primes dd2, wiping out its selection.
So, obviously, I don't really understand what I'm doing well enough to see how to do this. The visual web pack tutorials, where I started, really don't provide adequate explanation of what's going on, and the chapter on JSF in the J2EE tutorial is still a little abstract for me.
I would be forever indebted if somebody could please provide a pointer to a resource (preferably something a perl programmer can afford ;-) that could help me understand, in concrete terms, how a form, and the elements on the form (and their events), are processed.
Also, and as an aside, am I alone in thinking the whole Java thing is tremendously complex? I'm not talking about the Java language, which I find pretty intuitive, but the zillions of J* stuff around it, which seems somewhat dense. I really do want to learn this stuff, but it's pretty bewildering!
Thanks!
Regards,
Mike

Normally I would tell you to inject the PersonController bean into the PersonSelectionListener bean as a managed property. Then drill into the bean to get the data you need.
However, in this case you are dealing with a value change listener. Value change events are fired at the end of the Process Validations phase, before the Update Model Values phase. So in this case, the PersonController bean will not contain the selected person from the request. This is not a problem however, since the new value is passed via the ValueChangeEvent object.

Newbie - help with a SQL query for a bar chart - Originally posted in APEX

I originally posted this in the APEX forum but someone there suggested this is more of a SQL question. Anyone out there who can provide some assistance?
Hi,
I'm a new user on APEX with no real SQL knowledge and I'm trying to build a dashboard with charts into an existing APEX application. Based on another application, I have come up with the following SQL code:
select null link
, CATEGORY label
, count (decode(PROJECT_STATUS,'1',PROJECT_ID))"Active"
, count (decode(PROJECT_STATUS,'2',PROJECT_ID))"Complete"
, count (decode(PROJECT_STATUS,'3',PROJECT_ID))"On Hold"
, count (decode(PROJECT_STATUS,'4',PROJECT_ID))"Pipeline"
, count (decode(PROJECT_STATUS,'5',PROJECT_ID))"Pending Review"
from GRAPO_PROHEADTRK
where (PROJECT_STATUS='1' or PROJECT_STATUS='2' or PROJECT_STATUS='3' or PROJECT_STATUS='4' or PROJECT_STATUS='5' or PROJECT_STATUS='6')
group by CATEGORY
Order by COUNT(PROJECT_ID) DESC
The code from the other app was:
select null link
, FUNCTIONAL_AREA label
, count (decode(PROJECT_STATUS,'Active',PROJECT_ID))"Active"
, count (decode(PROJECT_STATUS,'Complete',PROJECT_ID))"Complete"
, count (decode(PROJECT_STATUS,'On Hold',PROJECT_ID)) "On Hold"
, count (decode(PROJECT_STATUS,'Recurring',PROJECT_ID))"Recurring"
, count (decode(PROJECT_STATUS,'Pipeline',PROJECT_ID))"Pipeline"
, count (decode(PROJECT_STATUS,'Not Approved',PROJECT_ID))"Not Approved"
from PM_V2
where LOB='S2S' and (FUNCTIONAL_AREA='Accounts Payable' or FUNCTIONAL_AREA='Expense' or FUNCTIONAL_AREA='Procurement' or FUNCTIONAL_AREA='Fixed Assets')
group by FUNCTIONAL_AREA
Order by COUNT(PROJECT_ID) DESC
I'm getting a "Failed to parse SQL query!" error when I try to run validation.
Is this enough info for some assistance? Any help would really be appreciated.
Thanks,
Rachel

Hi, Rachel,
user10774102 wrote:
I originally posted this in the APEX forum but someone there suggested this is more of a SQL question. Anyone out there who can provide some assistance?
Hi,
I'm a new user on APEX with no real SQL knowledge and I'm trying to build a dashboard with charts into an existing APEX application. Based on another application, I have come up with the following SQL code:
select null link
, CATEGORY label
, count (decode(PROJECT_STATUS,'1',PROJECT_ID))"Active"
, count (decode(PROJECT_STATUS,'2',PROJECT_ID))"Complete"
, count (decode(PROJECT_STATUS,'3',PROJECT_ID))"On Hold"
, count (decode(PROJECT_STATUS,'4',PROJECT_ID))"Pipeline"
, count (decode(PROJECT_STATUS,'5',PROJECT_ID))"Pending Review"
from GRAPO_PROHEADTRK
where (PROJECT_STATUS='1' or PROJECT_STATUS='2' or PROJECT_STATUS='3' or PROJECT_STATUS='4' or PROJECT_STATUS='5' or PROJECT_STATUS='6')
group by CATEGORY
Order by COUNT(PROJECT_ID) DESCIs there a problem with the code above?
It's curious that the WHERE clause includes "PROJECT_STATUS='6'", but there is no pivoted column for project_status='6', like there is for '1' through '5'. That's not necessarily a mistake, and it wouldn't raise an error in any case.
Instead of
where (PROJECT_STATUS='1' or PROJECT_STATUS='2' or PROJECT_STATUS='3' or PROJECT_STATUS='4' or PROJECT_STATUS='5' or PROJECT_STATUS='6')you could say
where PROJECT_STATUS IN ('1', '2', '3', '4', '5', '6')but that probably has nothing to do with your current problem.
The code from the other app was:
select null link
, FUNCTIONAL_AREA label
, count (decode(PROJECT_STATUS,'Active',PROJECT_ID))"Active"
, count (decode(PROJECT_STATUS,'Complete',PROJECT_ID))"Complete"
, count (decode(PROJECT_STATUS,'On Hold',PROJECT_ID)) "On Hold"
, count (decode(PROJECT_STATUS,'Recurring',PROJECT_ID))"Recurring"
, count (decode(PROJECT_STATUS,'Pipeline',PROJECT_ID))"Pipeline"
, count (decode(PROJECT_STATUS,'Not Approved',PROJECT_ID))"Not Approved"
from PM_V2
where LOB='S2S' and (FUNCTIONAL_AREA='Accounts Payable' or FUNCTIONAL_AREA='Expense' or FUNCTIONAL_AREA='Procurement' or FUNCTIONAL_AREA='Fixed Assets')
group by FUNCTIONAL_AREA
Order by COUNT(PROJECT_ID) DESC
I'm getting a "Failed to parse SQL query!" error when I try to run validation.Is that an Apex error message? Sorry, I don't know anything about Apex.
If you can't get a more specific error message from Apex, then try debugging this statement in SQL*Plus. When you get it fixed, then you can copy it back into Apex.
If this is a SQL problem, then you should be able to re-create the problem in pure SQL.
If you can't re-create the problem in pure SQL, then it's probably an Apex problem, and belongs in the Apex forum, not here.
I don't see anything obviously wrong with your code, but I can't tell if, for example, you spelled a column name wrong, or if something has the wrong data type
Is this enough info for some assistance? Any help would really be appreciated.It wiould be better if you posted a completE script that people could run to re-create the problem, and to test their ideas.
Whenever you have a problem, please post a little sample data (CREATE TABLE and INSERT statements, relevant columns only) from all tables involved.
Also post the results you want from that data, and an explanation of how you get those results from that data, with specific examples.
Always say which version of Oracle (and any other software, such as Apex) you're using.

Newbie, help with timesten 6.0.2

hi guys, i'm trying to install and configure timesten 6.0.2, in the same PC (it's name is demoserver) i have installed oracle 10g 10.2.0.1, the client tools for oracle 10g 10.2.0.0
i'm reading a document called cacheconnect.pdf it is installed with timesten documentation, i have tried to install timesten with and without Access Control, and in the same case is the same error, the user i logged on windows is 'ricardo', it's password is 'verde13' i'm doing the follow steps agreed the pdf file:
sqlplus system/passwordr@system1 system1 is the oracle service
SQL> CREATE USER testuser IDENTIFIED BY mypsswrd
DEFAULT TABLESPACE users;
SQL> GRANT connect, resource, create any trigger TO testuser;
SQL> COMMIT;
SQL> EXIT
then
Create a TimesTen DSN
Create a simple TimesTen system data source (System DSN), named cgDSN, as
described in Chapter 2, Creating TimesTen Data Stores of Oracle TimesTen In-
Memory Database Operations Guide.
For cgDSN, set:
Data Store Path and Name: c:\temp\cgds
Permanent Data Sz (MB): 16
Temporary Data Sz (MB): 16
User ID: testuser (this ID is also used as the Oracle User ID)
Oracle ID: system1
Oracle Password: mypsswrd
Use defaults for all other settings.
in this case i'm trying without Access Control so i skip this
Create an account on TimesTen
Note: You need to create an account on TimesTen only if you have Access
Control enabled on your TimesTen data store.
Use the ttIsql utility to connect to the cgDSN data store. Then use the CREATE
USER and GRANT statements to create a user, named testuser, with ADMIN
and DDL privileges:
ttIsql cgDSN
Command> CREATE USER testuser IDENTIFIED BY mypsswrd
Command> GRANT ADMIN, DDL TO testuser
skip end
Connect to your new Oracle account and create a table:
sqlplus testuser/mypsswrd@system1
SQL> CREATE TABLE readtab (a NUMBER(10,0) NOT NULL PRIMARY KEY,
b CHAR(31));
Then insert some rows and commit the changes:
SQL> INSERT INTO readtab VALUES (1, 'hello');
SQL> INSERT INTO readtab VALUES (2, 'world');
SQL> COMMIT;
Use the ttIsql utility to connect to the cgDSN data store. At the command prompt,
use the ttCacheUidPwdSet procedure to pass the cache administration user ID
and password as parameters.Then call the ttCacheStart procedure to start the
cache agent for the data store. In this example, the cache administration user ID
is testuser and the password is mypsswrd:
ttIsql cgDSNCommand> call ttCacheUidPwdSet('testuser','mypsswrd');
Command> call ttCacheStart();
here is my problem without Access Control i dont have an adminstrator, the error is:
Previous attempt resulted in the following:
Backend failed with exit status 1:
C:\TimesTen\tt60\srv\info\ws\cgi-bin\cache/ttBackEnd.exe -connStr "DSN=CGDSN" -user "RICARDO" -oraclepwd [Omitted] -oralogin
ERROR in ttBackEnd.c, line 864: prepare failed
ODBC Error/Warning = S1000, Additional Error/Warning = 5107
TT5107: Oracle(OCI) error in OCIServerAttach(): ORA-12154: TNS:could not resolve the connect identifier specified rc = -1 -- file "bdbConnect.c", lineno 1381, procedure "ttBDbConnect()"
ODBC Error/Warning = S1000, Additional Error/Warning = 5131
TT5131: Cannot connect to Oracle database: connect_string = "orcl", uid = "RICARDO", pwd is hidden -- file "bdbConnect
and with Access Control enabled is the same, how can i fix it?? i dont think is the TNS because from another client PC i can connect to Oracle using SQLPlus o VS.Net
i hope you can help me.
Regards.

With 6.0.3 I overcome this problem. But before installation make sure that ORACLE_HOME is set correctly as an environment parameter. And if it is not set, after setting you should reboot your computer.
Cheers
Gokben

I need some help with my GPS

I'm writing to ask you if You could somehow help me solve my GPS issue. I own Nokia 5800 XpressMusic. I've recently updated it's software and installed the new OVI Maps. I know that there is an option to use it offline which means without an Internet connection. When I start the Maps application and choose the offline mode, the only thing that appears at the top of the screen is "Searching position". The map is available but my position can't be specified without Internet on. When I turn my wireless router on, even though my maps are set in offline mode, it automatically connects to the Internet and spends something like 5KB download. If I keep navigating it spends even more. I've left my mobile phone offline to search for my position for an about half an hour but nothing happened. So, my question is, could you tell me what to do and how to use OVI Maps offline?
Solved!
Go to Solution.

Those are the only two sets of settings you need to change to use Ovi Maps without incurring network charges. There is no other setting. Try checking them again.
Start Ovi Maps, click on the Spanner icon>Internet>Connection>Offline
Exit to the main phone menu, then Menu>settings>Phone>Application settigs>Positioning>Positioning methods>make sure only Integrated Gps is ticked.

Newbie - HELP WITH CODE PLEASE!

Hi guys,
I have recently started using flash as some of the guys i work with suggested that it would be useful...
I am currently designing a basic site in AS3 and am stuck with a bit of coding. I keep getting the error message:
TypeError: Error #1009: Cannot access a property or method of a null object reference.
    at new_web_v1_fla::MainTimeline/frame141()
and having searched the net i cant find a solution. Here's my code:
stop();
function gohome(e:MouseEvent):void {
    gotoAndStop("home");
back_btn1.addEventListener(MouseEvent.CLICK, gohome);
function goit(e:MouseEvent):void {
    gotoAndStop("it");
it_btn.addEventListener(MouseEvent.CLICK, goit);
next_btn1.addEventListener(MouseEvent.CLICK, goit);
back_btn2.addEventListener(MouseEvent.CLICK, goit);
function goom(e:MouseEvent):void {
    gotoAndStop("om");
om_btn.addEventListener(MouseEvent.CLICK, goom);
next_btn2.addEventListener(MouseEvent.CLICK, goom);
back_btn3.addEventListener(MouseEvent.CLICK, goom);
function gogd(e:MouseEvent):void {
    gotoAndStop("gd");
gd_btn.addEventListener(MouseEvent.CLICK, gogd);
next_btn3.addEventListener(MouseEvent.CLICK, gogd);
back_btn4.addEventListener(MouseEvent.CLICK, gogd);
function gocu(e:MouseEvent):void {
    gotoAndStop("cu");
cu_btn.addEventListener(MouseEvent.CLICK, gocu);
next_btn4.addEventListener(MouseEvent.CLICK, gocu);
I hope someone can help me out!
Thanks
Jon

Thanks again for the advice, following your instructions i did use the // infornt of various bits of script.
My AS now looks like this and the buttons that have the as left in the script without // before them work fine, no errors:
stop();
function gohome(e:MouseEvent):void {
    gotoAndStop("home");
//back_btn1.addEventListener(MouseEvent.CLICK, gohome);
function goit(e:MouseEvent):void {
    gotoAndStop("it");
it_btn.addEventListener(MouseEvent.CLICK, goit);
next_btn1.addEventListener(MouseEvent.CLICK, goit);
//back_btn2.addEventListener(MouseEvent.CLICK, goit);
function goom(e:MouseEvent):void {
    gotoAndStop("om");
om_btn.addEventListener(MouseEvent.CLICK, goom);
//next_btn2.addEventListener(MouseEvent.CLICK, goom);
//back_btn3.addEventListener(MouseEvent.CLICK, goom);
function gogd(e:MouseEvent):void {
    gotoAndStop("gd");
gd_btn.addEventListener(MouseEvent.CLICK, gogd);
//next_btn3.addEventListener(MouseEvent.CLICK, gogd);
//back_btn4.addEventListener(MouseEvent.CLICK, gogd);
function gocu(e:MouseEvent):void {
    gotoAndStop("cu");
cu_btn.addEventListener(MouseEvent.CLICK, gocu);
//next_btn4.addEventListener(MouseEvent.CLICK, gocu);
the question now is how do i get my other buttons back into the script and get the bloody thing to work?
ARRRGGGHHH! i am beginning to wish that i had never started! lol
Thanks
Jon

Newbie Help with N8 Gps

Similar Messages

Maybe you are looking for