Nexus 1010 - Issue copying s/w onto device using SCP.

Hi
I'm trying to copy the new version of s/w ( nexus-1000v.4.2.1.SV1.4.iso) onto a Nexus 1010 switch using the command:
copy scp: bootflash:repository
The software starts to copy but unfortunately only gets to around 10% complete before failing. It's almost like it's getting stuck for some reason?
The file is quite large (163Mb), however, there is plenty of space on the disk (see below) so I cannot understand while this is happening.
switch# dir bootflash:repository
      16384     Nov 05 17:48:52 2010 lost+found/
156403712     Nov 05 17:52:02 2010 nam-4-2-1.iso
133965824     Nov 05 17:53:02 2010 nexus-1000v.4.0.4.SV1.3b.iso
Usage for bootflash://sup-local
305950720 bytes used
3685429248 bytes free
3991379968 bytes total
Does anyone have any suggestions as to why this is happening? Below is the exact output from the box:
switch# copy scp: bootflash:repository
Enter source filename: nexus-1000v.4.2.1.SV1.4.iso
Enter vrf (If no input, current vrf 'default' is considered):
Enter hostname for the scp server: 10.214.30.56
Enter username: 00000001
[email protected]'s
password:
nexus-1000v.4.2.1.SV1.4.iso                     9%   15MB   0.0KB/s - stalled -Read from remote host 10.214.30.56: Connection reset by peer
lost connection

Hi guys,
Any ideas on this?

Similar Messages

Syncing Podcasts onto devices using iTunes 11

I have several podcasts where i have over 70 episodes stored in iTunes11. When i connect any device e.g. iPod or iPad or iPhone to my Mac and try to sync some of the earliest of these Podcasts I cannot seem to scroll further down than about the first 40 or so episodes of these particular podcasts. I try and scroll down using the mouse and although I can briefly see some earlier episodes, it bounces back to just show as I say the latest 40 or so.
anyone else experiencing this?

I have solved my own question. You have to scroll down OUTSIDE the podcasts box. In case anyone has the same question.

Nexus 1010 + 1000v control vlan issue

Hi,
I have Nexus 1000v installed on nexus 1010. The nexus 1010 is in cluster and working fine. I have made network uplink option 3.
My VSM is configured to be on L3 mode. Hence I set control and packet vlan to 1 (on vsm). while creating the VSB too I have choosen control and packet vlan to be 1 (keeping in mind my mode will be L3).
Now The vsm is not coming up in HA. The redandancy log says degraded mode is true.
Is it because, the control packet coming from VSM after reaching the N1010, the packets are getting tagged with vlan 1. Since I have not set any native vlan on 1010, might be control vlan 1 is also tagged one. Is it this the case ?
help needed on this issue.
regards
Prasad K

Control vlan is a totally seperate VLAN then your System Console. The VLAN just needs to be available to the ESX host through the upstream physical switch and then make sure the VLAN is passed on the uplink port-profile that you assign the ESX host to.
We only need an interface on the ESX host if you decide to use L3 control. In that instance you would create or use an existing VMK interface on the ESX host.

Help with the error message that ADE is not allowed to copy a book onto my Nook. I have tried authorizing and unauthorizing many times--at wits end with this issue.

Help with the error message that ADE is not allowed to copy a book onto my Nook. I have tried authorizing and unauthorizing many times--at wits end with this issue.

I too am having the same problem. I have a new hard drive that was imaged from the old one and I'm trying to side load a book to my Nook Simple Touch.. I first installed ADE 4 then borrowed and downloaded a book from Overdrive. I tried a few times to delete and reauthorize both the computer and the Nook and each time I get an authorization error when I try to side load the book. I then found on the Nook forum that the Simple Touch and ADE 4 don't get along. So I uninstalled ADE 4 and installed ADE 3.
I then followed this recommended procedure found on the forum: I deleted the Digital Editions folder from my Nook, launched ADE 3 and authorized the computer, then connected the Nook. For a few seconds, hovering the mouse over the setting icon for the Nook displayed everything on the context menu grayed out. But then it showed the context menu and I was able to display the Nook's authorization, which was the same as the computer's. Still get the same error side loading the book. Deleting and reauthorizing doesn't help. And the Digital Editions folder is still missing from the Nook.

Nexus 1010 HA Active with warm standby

I have deployed two 1010 appliances, the upstream switches are two 6509 wihtout VSS.
I cannot get the HA up.
Output of show module is:
Mod Ports Module-Type                       Model               Status
1    0      Nexus 1010 (Virtual Services App Nexus1010           active *
2    0      Virtual Supervisor Module                             powered-up
Mod Sw                Hw
1    4.2(1)SP1(3)      0.0
Mod MAC-Address(es)                         Serial-Num
1    00-19-07-6c-5a-a8 to 00-19-07-6c-62-a8 NA
Mod Server-IP        Server-UUID                           Server-Name
1    10.146.102.10    NA                                    NA
Output of show system redundancy status is :
Redundancy role
      administrative:   primary
         operational:   primary
Redundancy mode
      administrative:   HA
         operational:   None
This supervisor (sup-1)
    Redundancy state:   Active
    Supervisor state:   Active
      Internal state:   Active with warm standby
Other supervisor (sup-2)
    Redundancy state:   Standby
Error in getting supervisor and internal state of other supervisor.
and the output of show system internal redundancy info is:
My CP:
slot: 0
domain: 25
role:   primary
status: RDN_ST_AC
state: RDN_DRV_ST_AC_SB
intr:   enabled
power_off_reqs: 0
reset_reqs:     9
Other CP:
slot: 1
status: RDN_ST_SB
active: true
ver_rcvd: true
degraded_mode: true
Redun Device 0:
name: ha0
pdev: f37e8640
alarm: true
mac: ff:ff:ff:ff:ff:ff
tx_set_ver_req_pkts:   319
tx_set_ver_rsp_pkts:   0
tx_heartbeat_req_pkts: 61193
tx_heartbeat_rsp_pkts: 0
rx_set_ver_req_pkts:   0
rx_set_ver_rsp_pkts:   0
rx_heartbeat_req_pkts: 0
rx_heartbeat_rsp_pkts: 0
rx_drops_wrong_domain: 0
rx_drops_wrong_slot:   0
rx_drops_short_pkt:    0
rx_drops_queue_full:   0
rx_drops_inactive_cp: 0
rx_drops_bad_src:      0
rx_drops_not_ready:    0
rx_drops_wrong_ver:    0
rx_unknown_pkts:       0
Redun Device 1:
name: ha1
pdev: f37e8240
alarm: false
mac: 00:02:3d:70:19:81
tx_set_ver_req_pkts:   314
tx_set_ver_rsp_pkts:   0
tx_heartbeat_req_pkts: 61193
tx_heartbeat_rsp_pkts: 0
rx_set_ver_req_pkts:   0
rx_set_ver_rsp_pkts:   5
rx_heartbeat_req_pkts: 0
rx_heartbeat_rsp_pkts: 61165
rx_drops_wrong_domain: 0
rx_drops_wrong_slot:   0
rx_drops_short_pkt:    0
rx_drops_queue_full:   0
rx_drops_inactive_cp: 0
rx_drops_bad_src:      0
rx_drops_not_ready:    0
rx_drops_wrong_ver:    0
rx_unknown_pkts:       0
Can anyone please help in resolving this issue.
Regards,
Sabih

Hi Sabih,
For a Nexus 1010 pair to form HA redundancy, the communicate with each other via the Control VLAN. You would have specified this during your installation.
Can you verify that they are both utilizing the same Control VLAN.
n1010# show svs domain
Furthermore, ensure that this vlan is defined and forwarding, on the relevant ports, on the upstream 6509s.
Thanks,
Michael

Nexus 1010 can not erase export-import folder

Hi Expert,
After we import the backup vsb. We try to erase the export-import folder. But system show "Device or resource busy". So we can not execute more export or import command. Please reference the below image and help us to fix this issue.
Ps. The Nexus 1010 version is "4.2.1.SP1.4"

Hello Meng,
I was able to recreate this problem in the lab. It appears it only occurs when importing a secondary VSB. A 'system switchover' of the N1010s frees the NFS locks. Not an ideal workaround, but a workaround.
CSCtz44247 has been opened for this problem.
Matthew

Need quick reply 4.2(1)SP1(5.1) on Nexus 1010?

We have most likely run into CSCtz74514 in 4.2(1)SP1(3) in a HA Nexus 1010 setup and need to upgrade. In the downloads I can find 4.1(1)SP1(5.1) for Nexus 1010. I have read through the release notes for 4.2(1)SP1(5.1). The only VSAs talked about are Nexus 1110-S and 1110-X
Is 4.2(1)SP1(5.1) really supported on a classic Nexus 1010 with 16GB ram or should we go for 4.2(1)SP1(4a)?
NTM-DC-VSA-01# show inventory
NAME: "Chassis", DESCR: "Nexus 1010 (Virtual Services Appliance) 2 slot Chassis "
PID: N1K-C1010           , VID: A   , SN: 1610440479132074267
NAME: "Slot 1", DESCR: "Nexus 1010 (Virtual Services Appliance)"
PID: N1K-C1010           , VID: A   , SN: QCI1533A662
NAME: "Slot 2", DESCR: "Nexus 1010 (Virtual Services Appliance)"
PID: N1K-C1010           , VID: A   , SN: QCI1533A7Q3
NTM-DC-VSA-01# show ver
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (c) 2002-2011, Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained herein are owned by
other third parties and are used and distributed under license.
Some parts of this software are covered under the GNU Public
License. A copy of the license is available at
http://www.gnu.org/licenses/gpl.html.
Software
loader:    version unavailable [last: loader version not available]
kickstart: version 4.2(1)SP1(3)
system:    version 4.2(1)SP1(3)
kickstart image file is: bootflash:/nexus-1010-kickstart-mz.4.2.1.SP1.3.bin
kickstart compile time: 7/8/2011 18:00:00 [07/09/2011 04:51:59]
system image file is:    bootflash:/nexus-1010-mz.4.2.1.SP1.3.bin
system compile time:     7/8/2011 18:00:00 [07/09/2011 05:16:25]
Hardware
cisco Nexus 1010 (Virtual Services Appliance) 2 slot Chassis ("Nexus 1010 (Virtual Services Appliance)")
   with 14304256 kB of memory.
Processor Board ID T023D701401
Device name: NTM-DC-VSA-01
bootflash:    3897832 kB
Disk Storage capacity for VM virtual disks: 346264 MB
Number of physical 1Gbps ethernet ports: 6

Thanks a lot Mathew! Would be nice if someone could update the install and upgrade guides so it's clear 1010 and 1010-X are supported as well as the 1110-S and 1110-X.

Can't copy any files onto phone, but have plenty of memory

My blackberry is only a few months old and a few days ago I tried to copy a podcast onto it and the following message came up:
The item “...” can’t be copied because there isn’t enough free space.
I then deleted a file the same size and tried again, but the same message came up. I then deleted all of the 1 album and two podcasts I had on it, and got the same message. I then went on to delete everything else, inbox, photos, videos, etc. I have no games or anything installed, and if I checked available space and it says I have 130215377 Bytes file free.
Is my Blackberry just broken or am I doing something wrong?
Solved!
Go to Solution.

Try doing a battery pull. While the device is on, remove the battery for 15-30 seconds, reinsert and wait for the device to reboot. Does this help? If not, can you try using a microSD card in your device?
If none of that helps, there are some other things that we can try in escalation. To do that, just let me know if you do have a microSD card installed on the device or if you are just using the internal memory on the device, etc.
Good luck!
If you want to thank someone for their comment, do so by clicking the Thumbs Up icon.
If your issue is resolved, don't forget to click the Solution button on the resolution!

Nexus 1010 - No MGMT0 Access?

Hi all, I hope someone here can help!
I am setting up a Cisco Nexus 1010 appliance, but cannot access it through the MGMT0 interface!
What I am trying to do is copy over the 1000V .iso file to install a vsm, but I can not even ping the mgmt0 interface.
I have booted from the 4.2(1)SP1(3) iso, ran through the initial setup where I set the uplink type, domain id, vlan id and mgmt0 ip details.
Current config and sh tech attached
Let me know what other information I should post!
Kind regards, Ash.

Hi everyone,
I have a problem, similar to Ashley's in regards to reachability of N1010 in my lab...
I'm using network-uplink type 1 as it would be more than enough for my lab deployment. I have configured the CIMC and can reach/configure the device from there pretty easily. But, no matter how I try, I can't seem to get management access.
The N1010 is connected via it's Lom0 port to a Catalyst (at Fa0/10), which is configured as a trunk port. I'm using Vlan10 for all purposes...
The uplink switch has a configuration like this:
interface VLAN10
ip address 10.2.1.66 255.255.255.128
no ip directed-broadcast
no ip route-cache
interface FastEthernet0/10
description NEXUS_1010_TEST-LOM0
switchport trunk encapsulation dot1q
switchport trunk native vlan 10
switchport mode trunk
And the show running-config output from the Nexus1010 shows this:
!Command: show running-config
!Time: Tue Jun 5 21:21:59 2012
version 4.2(1)SP1(4)
no feature telnet
username admin password 5 $1$GW2TtGHE$oHUMu5em2..2XvSqJDlMb. role network-admin
banner motd #Nexus 1010#
ip domain-lookup
ip domain-lookup
switchname N1010-ANK
snmp-server user admin network-admin auth md5 0xbc6feda9b778b02e324d11adda844e5c
priv 0xbc6feda9b778b02e324d11adda844e5c localizedkey
vrf context management
ip route 0.0.0.0/0 10.2.1.126
vlan 1,10
port-channel load-balance ethernet source-mac
port-profile default max-ports 32
vdc N1010-ANK id 1
limit-resource vlan minimum 16 maximum 2049
limit-resource monitor-session minimum 0 maximum 2
limit-resource vrf minimum 16 maximum 8192
limit-resource port-channel minimum 0 maximum 768
limit-resource u4route-mem minimum 32 maximum 32
limit-resource u6route-mem minimum 16 maximum 16
limit-resource m4route-mem minimum 58 maximum 58
limit-resource m6route-mem minimum 8 maximum 8
network-uplink type 1
interface GigabitEthernet1
interface GigabitEthernet2
interface GigabitEthernet3
interface GigabitEthernet4
interface GigabitEthernet5
interface GigabitEthernet6
interface PortChannel1
interface mgmt0
ip address 10.2.1.40/25
interface control0
line console
boot kickstart bootflash:/nexus-1010-kickstart-mz.4.2.1.SP1.4.bin
boot system bootflash:/nexus-1010-mz.4.2.1.SP1.4.bin
boot kickstart bootflash:/nexus-1010-kickstart-mz.4.2.1.SP1.4.bin
boot system bootflash:/nexus-1010-mz.4.2.1.SP1.4.bin
svs-domain
domain id 200
control vlan 10
management vlan 10
svs mode L2
vnm-policy-agent
registration-ip 0.0.0.0
shared-secret **********
log-level info
In no way I can access the mgmt0 interface IP from the network, or vice-versa.
The weird part is, I can see the Nexus in CDP neighbours, and I also can see the mac address of the mgmt0 interface on the switch (along with a correct IP assignment in arp table).
DemoSW#sh cdp nei
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
                  S - Switch, H - Host, I - IGMP, r - Repeater
Device ID        Local Intrfce     Holdtme    Capability Platform Port ID
N1010-ANK(1157310Fas 0/10           126         S I       Nexus1010 control0
N1010-ANK(1157310Fas 0/10           126         S I       Nexus1010 mgmt0
N1010-ANK(QCI1614Fas 0/10           126          H        Nexus1010 eth0
DemoSW#
DemoSW#sh mac-address-table interface fa0/10
Non-static Address Table:
Destination Address Address Type VLAN Destination Port
0002.3d70.c800       Dynamic         10 FastEthernet0/10
0002.3d70.c801       Dynamic         10 FastEthernet0/10
0010.18cf.7886       Dynamic         10 FastEthernet0/10
36ce.bc88.c2d9       Dynamic         10 FastEthernet0/10
DemoSW#sh arp | incl 0002.3d70.c801
Internet 10.2.1.40               0   0002.3d70.c801 ARPA   VLAN10
DemoSW#ping 10.2.1.40
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.2.1.40, timeout is 2 seconds:
Success rate is 0 percent (0/5)
DemoSW#
Any ideas???

To upload photos from my pc onto my ipad using a usb stick. I bought a camera connector kit and tried placing the usb stick onto one of the white square adaptors, stuck it into the ipad2 and I got 'the device uses too much power'' message. Pls help.

I am not very familiar with the ipad2. I wished to transfer some photos from my pc (not an apple pc but that is the only one I have) to my ipad2 as I thought it would be easier to cull them, edit, crop etc to create albums for our recent trip (the photos are already on the pc and no longer on the camera memory card). When I place the usb stick on the adaptor and stick it onto the Ipad2 I keep getting 'device uses too much power/ requires too much power' message. I read somewhere on the internet that a usb hub could be used to solve the issue but that did not work either. What am I doing wrong? Is there actually a way around this problem. If not why does apple sell this product for Ipad users at all?
Thank you for any help/ solution you can offer.
Regards

I'd ask that on the iPad forum.
https://discussions.apple.com/community/ipad

How do I copy MP4 files onto my IPad while travelling?

Hello all
I picked up my first IPad through work last week, and am still familiarising myself with the device. What I did manage to do is connect it to ITunes on my home computer and copy all of our childrens TV shows onto the device for our daughter to watch, and it all went smoothly.
I have a question regarding this process however. I tend to watch a lot of TV shows, and in most cases I wait until after the season is finished and pick up the boxed set, so that I can watch it when I want, without commercials. What I then do is convert them to (unprotected) MP4 files that I then usually copy to my PS3 to watch them on our TV. Just as a test, I copied a few onto the IPad and they look great, I could easily see myself using this device to watch shows while travelling.
However, our IPad is only 16 gigs, and in longer trips I would probably want to take more shows than that would allow. I also have a 1 Terrabyte portable harddrive though, that I can fit ample amount of shows on.
At the moment I have only connected the IPad to one computer running ITunes, which is my PC at home. However lets assume I was travelling, and had both my external hard drive and IPad. What would be the best solution for copying movies from that external harddrive to the IPad to allow me to watch additional shows? Unless I'm mistaken, I can have up to 5 computers authorised with my account. Would it in theory be possible to find a PC, authorise it to my Ipad, copy the files over and then deauthorise that PC? Or if not, what is the recommended solution?
Apologies if this is common knowledge, I'm still a newbie.

Even though you can have your iTunes account authorized on 5 computers your iPad can only be linked to one computer. If you used another computer to copy your content from your external drive you would have to Restore the iPad with the computer erasing all other data. The process will allow you to backup then Restore to that back up but it will not contain any of the media files you wish to keep on the iPad. This is why it is important to get the most storage on an iOS device you can afford.
You might want to look at something like Kingston's Wi-Drive which is an external drive your iPad can access through wifi. http://www.kingston.com/us/usb/wireless#wid I don't think it has any integration with iTunes but you could put a copy of the videos you wish to take with you then play them on it it's app.

Nexus 1010 HA

Hello
I have a problem with Nexus 1010 HA.
I have two Nexus 1010. One is configured as Primary and the other as Secondary.
I have a VSB (VSM type) created on both, enabled as Primary and Secondary respectively.
HA between VSMs works fine. But HA between Nexus is not working. Something is missed. Any ideas? Thank you!!!
Nexus 1010 - Primary
NX-1010-TB# sh system red status
Redundancy role
      administrative:   primary
         operational:   primary
Redundancy mode
      administrative:   HA
         operational:   None
This supervisor (sup-1)
    Redundancy state:   Active
    Supervisor state:   Active
      Internal state:   Active with no standby
NX-1010-TB# sh mo
Mod Ports Module-Type                       Model               Status
1    0      Cisco Nexus1010 Chassis           Nexus1010           active *
Mod Sw                Hw
1    4.2(1)SP1(2)      0.0
Mod MAC-Address(es)                         Serial-Num
1    00-19-07-6c-5a-a8 to 00-19-07-6c-62-a8 NA
Mod Server-IP        Server-UUID                           Server-Name
1    10.1.30.53       NA                                    NA
Nexus 1010 - Secondary
switch# sh sys red st
Redundancy role
      administrative:   secondary
         operational:   secondary
Redundancy mode
      administrative:   HA
         operational:   None
This supervisor (sup-2)
    Redundancy state:   Active
    Supervisor state:   Active
      Internal state:   Active with no standby
Other supervisor (sup-1)
    Redundancy state:   Not present
switch# sh module
Mod Ports Module-Type                       Model               Status
2    0      Cisco Nexus1010 Chassis           Nexus1010           active *
Mod Sw                Hw
2    4.2(1)SP1(2)      0.0
Mod MAC-Address(es)                         Serial-Num
2    00-19-07-6c-5a-a8 to 00-19-07-6c-62-a8 NA
Mod Server-IP        Server-UUID                           Server-Name
2    0.0.0.0          NA                                    NA
* this terminal session

Prasad,
This means that there is some sort of a communication issue between the two Nexus 1010 switches in the control VLAN. You should probably check the upstream configuration on the ports that connect to the 1010 links carrying the control traffic and also the links involved in the control path.
Thanks,
Shankar

Nexus 1010 HA Error

              Hi,
While I bring Up Secondary Nexus 1010 I am getting this error on primary
Error in getting supervisor and internal state of other supervisor.
sh redundancy status
Redundancy role
      administrative:   primary
         operational:   primary
Redundancy mode
      administrative:   HA
         operational:   None
This supervisor (sup-1)
    Redundancy state:   Active
    Supervisor state:   Active
      Internal state:   Active with warm standby
Other supervisor (sup-2)
    Redundancy state:   Standby
Error in getting supervisor and internal state of other supervisor.
On the redundant (standy ) unit I am getting this message
%SYSLOG-2-SYSTEM_MSG: Did not receive supstate notification in 180 seconds. Still waiting
What could be possible reason ? can this be a firmware mismatch ? Both are having same configuration for management control and packet vlan. Both are on same L2 network. If I disconnect the standby unit management cable, it will boot. But if management cable is connected, it will be stuck in the above phase.
regards
Prasad K

Prasad,
This means that there is some sort of a communication issue between the two Nexus 1010 switches in the control VLAN. You should probably check the upstream configuration on the ports that connect to the 1010 links carrying the control traffic and also the links involved in the control path.
Thanks,
Shankar

ADE crashing when opening library ebook or copying it to a device

Adobe Digital Editions keeps crashing every time I try to open a borrowed library book (epub) and every time I try to copy it to my device.
I'm using as macbook air and the device is a Kobo Aura. My computer is authorized with my Adobe ID, I have tried restarting the program and the computer and the device connection, and I have tried adding the epub file directly from my computer to my device file, but of course my device tells me it is not viewable because it is DRM protected.
I've seen a few other people having this exact problem (but with different devices or computers, so it appears to truly be an ADE issue), but with no answers! Please help!

Never mind, I got it to work. I erased ADE 4 and installed ADE 3 (Adobe Digital Editions downloads) and then I unauthorized the computer and the device and reauthorized them with the Overdrive ID (which I had to create at Overdrive.com) instead of the Adobe ID.

How to copy printed information onto party invitations that has a colorful bordered paper.

I have a party invitation that has a colorful border with a blank white area in the middle for text. There are two invitations on a single sheet of paper that is a standard letter size of 8-1/2 by 11. I have double printed the text I want on a standard letter size piece of paper and tried to copy the text onto the invitation without success. When trying to print, I keep getting an error message that says "paper detected does not match paper size or type selected. I need help in setting up the printer to allow me to copy. Help please!!

Thank you Sukrit for responding.
The computer I am using is controlled by a government agency. They do not allow users to install or modify any software. The file I am using, though a public document, may not be advisable to be posted online.
However, my solution to the issue was to reprint the document that I was pasting into and modifying the print settings to rotate the PDF image. First, I had to change the size of the PDF beyond the original full size dimensions to account for the scale change. Then change the print settings to print landscape while telling adobe's advanced settings to print portrait. After some finesse with other settings for scale, I was able to copy and paste the polygon without loosing the scale. This took me a week to figure out. An extreme waste of time for such a simple issue that should not occur in such a popular software.

Nexus 1010 - Issue copying s/w onto device using SCP.

Similar Messages

Maybe you are looking for