Nexus 1010, out of band

We are installing Nexus 1010 using the topology 3 connection and we will configure VSB DCNM.
1st Question
Topology 3, use the interfaces 1 and 2 for traffic management vlan and I want to know if I can connect these interfaces to my segment from out of band or needs to go connected on the segment from server.
2nd Question
we are going to configure DCNM on Nexus 1010 which must have comunication with the management interfaces from the other nexus switch through of the network out of band. Management interfaces of VSMS should be on the same network OOB? or must be on another network?
Thanks in advance

Hi,
Yes, it is possible. When you login as admin and you want to get to another vdc, you just use this command:
switchto vdc
This will take to the that vdc. If you want to switch back to the admin vdc, you just type "switchback"
HTH

Similar Messages

Nexus 7K out of band Management interface

Dears,
regarding to the out of band Management interface , if I configured an intervace vlan to be as a managment interface for one vdc ( the default vdc )
, when I connected to this vdc via telnet , can I switch to any other vdc ? ( suppose that I have the Admin role which allows me to enter and config all the vdc's )
If that is possible so that I dont have to make a dedicated managment ip for each VDC
I need to do that only if I want to make vdc admin's account to allow some users to access specific vlans only , is that true ?

Hi,
Yes, it is possible. When you login as admin and you want to get to another vdc, you just use this command:
switchto vdc
This will take to the that vdc. If you want to switch back to the admin vdc, you just type "switchback"
HTH

Nexus 5500 - inband via default vrf and out-of-band via management vrf

Nexus 5548 with no layer 3 module. Want to manage the device via 10.122.122.5 9 (inband) and 10.122.123.58 (out-of-band)
Currently i can get to the device using 10.122.123.58 via management vrf but can't get to 10.122.122.5 via default vrf.
A couple of questions please:
1) Is this design support? or do i need a layer 3 module + licensing to use the default vrf?
2) What does "pending" in the default vrf routing table indicate?
interface Vlan12
no shutdown
ip address 10.122.122.5/25
ip route 0.0.0.0/0 10.122.122.1
interface mgmt0
vrf member management
ip address 10.122.123.58/26
vrf context management
ip route 0.0.0.0/0 10.122.123.1
sh ip route vrf all
IP Route Table for VRF "default"
'*' denotes best ucast next-hop
'**' denotes best mcast next-hop
'[x/y]' denotes [preference/metric]
'%<string>' in via output denotes VRF <string>
0.0.0.0/0, ubest/mbest: 1/0, pending
*via 10.122.122.1, [1/0], 3w1d, static
10.122.122.0/25, ubest/mbest: 1/0, attached, pending
*via 10.122.122.5, Vlan12, [0/0], 3w1d, direct
10.122.122.5/32, ubest/mbest: 1/0, attached, pending
*via 10.122.122.5, Vlan12, [0/0], 3w1d, local
IP Route Table for VRF "management"
'*' denotes best ucast next-hop
'**' denotes best mcast next-hop
'[x/y]' denotes [preference/metric]
'%<string>' in via output denotes VRF <string>
0.0.0.0/0, ubest/mbest: 1/0
*via 10.122.123.1, [1/0], 3w1d, static
10.122.123.0/26, ubest/mbest: 1/0, attached
*via 10.122.123.58, mgmt0, [0/0], 3w1d, direct
10.122.123.58/32, ubest/mbest: 1/0, attached
*via 10.122.123.58, mgmt0, [0/0], 3w1d, local

Hi,
Yes, it is possible. When you login as admin and you want to get to another vdc, you just use this command:
switchto vdc
This will take to the that vdc. If you want to switch back to the admin vdc, you just type "switchback"
HTH

Nexus 1010 weird HA mechanism

Hello guys,
We are in the middle of the installation of 2 Nexus 1010 appliances.
the two appliances have a failover mechanism where you have only one address for the cluster of appliance. I don't think that it is a good idea because the Vsm on the appliance already has its own HA mechanism. on the contrary, the appliance HA mechanism is confusing because you can only access by telnet the primary appliance. What if your active VSM is running on the secondary appliance? how to access Out of band to this one?
It would make more sense to me if each appliance 1010 would be standalone?
am I missing something here? any ideas on why we use Ha for the Nexus 1010?
Thank you
laurent
Sent from Cisco Technical Support iPad App

First of all. According to the documentation Nexus 1010 is not supported in standalone scenario.
• The HA standalone role is not supported for the Cisco Nexus 1010.
• Cisco Nexus 1010 is not supported in the non HA mode.
http://www.cisco.com/en/US/partner/docs/switches/datacenter/nexus1000/sw/4_2_1_s_p_1_4_a/install_upgrade/guide/n1010_installupgrade_install.html#wp1065391
I see the HA mechanism between N1010 as a way how to manage them. Nothing more, nothing less. N1000V on top of them do have their HA mechanism. I am able to reach standby N1010 VSM either by:
ssh to the LOM port of the standby N1010, then connect host and then login virtual-service-blade or
ssh to the N1010 cluster address and then login virtual-service-blade secondary
Petr
Message was edited by: Petr Mojzisek

Prime Infrastructure Out of band

Hi
What is the meaning of the term "out of band". You will find this term under operation -->device workcenter-->config archive, it is separate column.
regards
Hansruedi

Out-of-band simply refers to communications which occur outside of a previously established communications method or channel. In the case of cisco prime and being part of the config archive I suspect it is refering to out-of-band management ports which are now part of all new cisco switches (2960S, 3750X, Nexus 7K and 5K, etc). The out-of-band port is designed to continue to provide console access even in the even of a primary network subsystem failure. Hence in a properly designed network there would exist a entirely seperate out-of-band network which relies on none of the hardware or software forming part of the primary production network.
In the case of being part of the config archive I would then conclude that the out of band column simply relates to all the config for out of band managment and the associated port, so all the config for any fa0 Layer 3 OOB Management port that exists on a switch/router would appear here, as might any vrf config that seperates the OOB port from the rest of the network.

Vdc out of band management

I saw this digram from Cisco,but no configuration example. Right now I have nexus 7010 with sup 2 version 6.2.2. I could not assign the interface mgmt 0 to the different VDC. Do anyone do out of band management for VDCs? or can anyone let me know how could I configure the out of band management for vdc?
Thanks a lot.
Regards

Hi Pille,
Thanks for your reply. I switch to the vdc and I did not find the "int mgmt0" in these VDCs, the mgmt0 only exists in the system VDC. In this case, I do not know how to configure the seperatt IP for every context. Could you share with me more details for the configuration?
Thanks
Regards
Ying Wang

Problem with Out of Band Discovery resulting with Out of Band features not available in SCCM console for computers with provisioned AMT device

Hi,
We configured the Out of Band component, but are using Intel SCS RCS to provision AMT devices remotely. The remote configuration process with Intel SCS works fine; we are able to connect to the AMT web UI and we can use a free KVM tool to manage the computer
remotely.
The AMT devices are configured with AD integration, so an object is created for each of them in a specific OU. Also, an AD group is added to the AMT devices so remote PT Administration permission is granted to it. This group includes the ConfigMgr Site
Server account, the account of the server running the Out of Band Service Point and my own user account.
This configuration seems OK since when connecting to the AMT web UI, I use Windows Integrated authentication with my user account and can manage the device successfully.
So the only step remaining is running the OOB discovery to enable Out of Band features for the computers in the SCCM console. We want to use the ConfigMgr OOB console. I right-click a computer or a collection and launch the AMT discovery. I check the OOB
server log, I don't see errors; the OOB service point connects to the AMT device and discover a status of 4, which is Externally provisioned, as expected. The problem is the AMT Status, AMT Version and Provisioned AMT fields for the computer in the ConfigMgr
console doesn't get updated, even after doing display refresh.
Here's the amtopmgr.log (I changed computer name and IP address information to protect client privacy) :
General Worker Thread Pool: Work thread 364 started SMS_AMT_OPERATION_MANAGER 2014-06-16 15:16:25 364 (0x016C)
Discover COMPUTERA using IP address 192.168.12.7 SMS_AMT_OPERATION_MANAGER 2014-06-16 15:16:25 364 (0x016C)
AMT Discovery Worker: There are 1 tasks in pending list SMS_AMT_OPERATION_MANAGER 2014-06-16 15:16:25 2792 (0x0AE8)
AMT Discovery Worker: Wait 20 seconds... SMS_AMT_OPERATION_MANAGER 2014-06-16 15:16:25 2792 (0x0AE8)
AMT Discovery Worker: Wakes up to process instruction files SMS_AMT_OPERATION_MANAGER 2014-06-16 15:16:25 2792 (0x0AE8)
AMT Discovery Worker: There are 1 tasks in pending list SMS_AMT_OPERATION_MANAGER 2014-06-16 15:16:25 2792 (0x0AE8)
AMT Discovery Worker: Wait 20 seconds... SMS_AMT_OPERATION_MANAGER 2014-06-16 15:16:25 2792 (0x0AE8)
DoPingDiscoveryForAMTDevice succeeded. SMS_AMT_OPERATION_MANAGER 2014-06-16 15:16:25 364 (0x016C)
Flag iWSManFlagSkipRevocationCheck is not set. SMS_AMT_OPERATION_MANAGER 2014-06-16 15:16:25 364 (0x016C)
session params : https://COMPUTERA.contoso.com:16993 , 11001 SMS_AMT_OPERATION_MANAGER 2014-06-16 15:16:25 364 (0x016C)
DoWSManDiscovery succeeded with user name: admin. AMTStatus = 1. SMS_AMT_OPERATION_MANAGER 2014-06-16 15:16:32 364 (0x016C)
Start Kerberos Discovery SMS_AMT_OPERATION_MANAGER 2014-06-16 15:16:32 364 (0x016C)
Flag iWSManFlagSkipRevocationCheck is not set. SMS_AMT_OPERATION_MANAGER 2014-06-16 15:16:32 364 (0x016C)
session params : https://COMPUTERA.contoso.com:16993 , 484001 SMS_AMT_OPERATION_MANAGER 2014-06-16 15:16:32 364 (0x016C)
DoKerberosWSManDiscovery succeeded. AMTStatus = 4. SMS_AMT_OPERATION_MANAGER 2014-06-16 15:16:32 364 (0x016C)
Discovery to IP address 192.168.12.7 16 15:16:32 364 (0x016C)
CSMSAMTDiscoveryTask::Execute, discovery to STI17259CPCO succeed. AMT status is 4. SMS_AMT_OPERATION_MANAGER 2014-06-16 15:16:32 364 (0x016C)
CSMSAMTDiscoveryTask::Execute - DDR written to E:\SMS\MP\OUTBOXES\ddr.box SMS_AMT_OPERATION_MANAGER 2014-06-16 15:16:32 364 (0x016C)
CStateMsgReporter::DeliverMessages - Queued message: TT=1201 TIDT=0 TID='Fill Machine Property' SID=1 MUF=0 PCNT=5, P1='COMPUTERA' P2='' P3='COMPUTERA.contoso.com' P4='' P5='' SMS_AMT_OPERATION_MANAGER 2014-06-16 15:16:32 364 (0x016C)
CStateMsgReporter::DeliverMessages - Created state message file: E:\SMS\MP\OUTBOXES\StateMsg.box\6heghx71.SMX SMS_AMT_OPERATION_MANAGER 2014-06-16 15:16:32 364 (0x016C)
CStateMsgReporter::DeliverMessages - Queued message: TT=1201 TIDT=0 TID='Unspecified' SID=10 MUF=0 PCNT=1, P1='COMPUTERA.contoso.com' 16 15:16:32 364 (0x016C)
CStateMsgReporter::DeliverMessages - Created state message file: E:\SMS\MP\OUTBOXES\StateMsg.box\rmit91js.SMX SMS_AMT_OPERATION_MANAGER 2014-06-16 15:16:32 364 (0x016C)
General Worker Thread Pool: Succeed to run the task COMPUTERA.contoso.com 16 15:16:32 364 (0x016C)
General Worker Thread Pool: Work thread 364 has been requested to shut down. SMS_AMT_OPERATION_MANAGER 2014-06-16 15:16:32 364 (0x016C)
General Worker Thread Pool: Work thread 364 exiting. SMS_AMT_OPERATION_MANAGER 2014-06-16 15:16:32 364 (0x016C)
The Management Point is up and running.
Any suggestion or advice is welcomed!
Thank you
Patrick

I found something interesting on this problem, it seems the OOB discovery process is working fine, but for an unknown reason, the site server is not receiving the information from the OOB Service Point to update the AMT Status of the client in the SCCM
database.
The log tells me that a DDR file is created to be sent to the site server. When looking into the SMS\MP\Outboxes\ddr.box folder, I see about 50 DDR files, the oldest one is dated when I started testing OOB discovery.
So the server is unable to send the files to the site server.
Also, since I started this thread, I noticed another issue that could be related to this problem. The same server is also holding the State Migration Point role, it is working fine, but when doing USMT operations, the status of the computer association is
not updated in the console (In Progress, Completed, missing USMT store path, etc.). When looking into the SMS folder on the server, I see a big backlog of SVF files containing information related to the SMP.
I looked into the log files, but didn't find the errors yet to explain this.
The computer account of the server is a member of the SMS_SiteSystemToSiteServerConnection_Stat_XXX group on the site server.
Note that status messages are being sent successfully, I see them in the Monitoring node of the console under Component State, and there is no backlog in the SMS\MP\Outboxes\statemsg.box folder.
Tnx for your help
Patrick

Nexus 1010 HA Active with warm standby

I have deployed two 1010 appliances, the upstream switches are two 6509 wihtout VSS.
I cannot get the HA up.
Output of show module is:
Mod Ports Module-Type                       Model               Status
1    0      Nexus 1010 (Virtual Services App Nexus1010           active *
2    0      Virtual Supervisor Module                             powered-up
Mod Sw                Hw
1    4.2(1)SP1(3)      0.0
Mod MAC-Address(es)                         Serial-Num
1    00-19-07-6c-5a-a8 to 00-19-07-6c-62-a8 NA
Mod Server-IP        Server-UUID                           Server-Name
1    10.146.102.10    NA                                    NA
Output of show system redundancy status is :
Redundancy role
      administrative:   primary
         operational:   primary
Redundancy mode
      administrative:   HA
         operational:   None
This supervisor (sup-1)
    Redundancy state:   Active
    Supervisor state:   Active
      Internal state:   Active with warm standby
Other supervisor (sup-2)
    Redundancy state:   Standby
Error in getting supervisor and internal state of other supervisor.
and the output of show system internal redundancy info is:
My CP:
slot: 0
domain: 25
role:   primary
status: RDN_ST_AC
state: RDN_DRV_ST_AC_SB
intr:   enabled
power_off_reqs: 0
reset_reqs:     9
Other CP:
slot: 1
status: RDN_ST_SB
active: true
ver_rcvd: true
degraded_mode: true
Redun Device 0:
name: ha0
pdev: f37e8640
alarm: true
mac: ff:ff:ff:ff:ff:ff
tx_set_ver_req_pkts:   319
tx_set_ver_rsp_pkts:   0
tx_heartbeat_req_pkts: 61193
tx_heartbeat_rsp_pkts: 0
rx_set_ver_req_pkts:   0
rx_set_ver_rsp_pkts:   0
rx_heartbeat_req_pkts: 0
rx_heartbeat_rsp_pkts: 0
rx_drops_wrong_domain: 0
rx_drops_wrong_slot:   0
rx_drops_short_pkt:    0
rx_drops_queue_full:   0
rx_drops_inactive_cp: 0
rx_drops_bad_src:      0
rx_drops_not_ready:    0
rx_drops_wrong_ver:    0
rx_unknown_pkts:       0
Redun Device 1:
name: ha1
pdev: f37e8240
alarm: false
mac: 00:02:3d:70:19:81
tx_set_ver_req_pkts:   314
tx_set_ver_rsp_pkts:   0
tx_heartbeat_req_pkts: 61193
tx_heartbeat_rsp_pkts: 0
rx_set_ver_req_pkts:   0
rx_set_ver_rsp_pkts:   5
rx_heartbeat_req_pkts: 0
rx_heartbeat_rsp_pkts: 61165
rx_drops_wrong_domain: 0
rx_drops_wrong_slot:   0
rx_drops_short_pkt:    0
rx_drops_queue_full:   0
rx_drops_inactive_cp: 0
rx_drops_bad_src:      0
rx_drops_not_ready:    0
rx_drops_wrong_ver:    0
rx_unknown_pkts:       0
Can anyone please help in resolving this issue.
Regards,
Sabih

Hi Sabih,
For a Nexus 1010 pair to form HA redundancy, the communicate with each other via the Control VLAN. You would have specified this during your installation.
Can you verify that they are both utilizing the same Control VLAN.
n1010# show svs domain
Furthermore, ensure that this vlan is defined and forwarding, on the relevant ports, on the upstream 6509s.
Thanks,
Michael

Out of band Clocking between MWR-2941

Good morning I'm having problems configuring out
of band clocking between two MWR-2941
I have configured one MWR-2941 to
Remote
recovered-clock slave
interface Virtual-Cem 0/24
cem 0
xconnect 10.10.10.2 7600 encapsulation mpls
network-clock select 1 PACKET-TIMING
network-clock-select hold-timeout 900
the Master Router is getting it clock signal from an E1/T1 interface
MASTER
controller E1 0/0
clock source internal
cem-group 0 unframed
description Clocking-Signal
controller E1 0/13
clock source line
cem-group 0 unframed
interface CEM0/0
description Clocking-Signal
no ip address
cem 0
xconnect 172.16.20.26 7600 encapsulation mpls
interface CEM0/13
no ip address
cem 0
xconnect 172.16.20.26 11591 encapsulation mpls
with this configuration i can't get any clocking at the remote site. I have configured this between a Cisco 7609 and the MWR-2941 without problem, but in the Cisco 7609 I can create another virtual-cem interface. But I can't find a way to create a virtual-cem in the MWR-2941 that should be working as the clock master.
Any help will be greatly appreciated.
Thank you very mucy.

Thank you for your attention ,
I did not see such out put of my sho mac add command ,
I sent a image of my current topology , it may be useful , please find it.
I used router instead of cisco layer 3 switches (SVI for user access vlan is configured on router as sub interfaces) , and On my NAC Server I created a vlan mapping rule that map unauthenticated vlan to one of my access vlan ,
I have a problem with my Managed subnet !! I have to put my Managed Subnet as default gateway for my client because if I put the router SVI cisco nac agent client does not pop up at all !!!
I read different documents about that and all of them said that your client default gateway must be SVI , but it does not work,
best regard

Nexus 1010 - Issue copying s/w onto device using SCP.

Hi
I'm trying to copy the new version of s/w ( nexus-1000v.4.2.1.SV1.4.iso) onto a Nexus 1010 switch using the command:
copy scp: bootflash:repository
The software starts to copy but unfortunately only gets to around 10% complete before failing. It's almost like it's getting stuck for some reason?
The file is quite large (163Mb), however, there is plenty of space on the disk (see below) so I cannot understand while this is happening.
switch# dir bootflash:repository
      16384     Nov 05 17:48:52 2010 lost+found/
156403712     Nov 05 17:52:02 2010 nam-4-2-1.iso
133965824     Nov 05 17:53:02 2010 nexus-1000v.4.0.4.SV1.3b.iso
Usage for bootflash://sup-local
305950720 bytes used
3685429248 bytes free
3991379968 bytes total
Does anyone have any suggestions as to why this is happening? Below is the exact output from the box:
switch# copy scp: bootflash:repository
Enter source filename: nexus-1000v.4.2.1.SV1.4.iso
Enter vrf (If no input, current vrf 'default' is considered):
Enter hostname for the scp server: 10.214.30.56
Enter username: 00000001
[email protected]'s
password:
nexus-1000v.4.2.1.SV1.4.iso                     9%   15MB   0.0KB/s - stalled -Read from remote host 10.214.30.56: Connection reset by peer
lost connection

Hi guys,
Any ideas on this?

Nexus 1010 HA

Hello
I have a problem with Nexus 1010 HA.
I have two Nexus 1010. One is configured as Primary and the other as Secondary.
I have a VSB (VSM type) created on both, enabled as Primary and Secondary respectively.
HA between VSMs works fine. But HA between Nexus is not working. Something is missed. Any ideas? Thank you!!!
Nexus 1010 - Primary
NX-1010-TB# sh system red status
Redundancy role
      administrative:   primary
         operational:   primary
Redundancy mode
      administrative:   HA
         operational:   None
This supervisor (sup-1)
    Redundancy state:   Active
    Supervisor state:   Active
      Internal state:   Active with no standby
NX-1010-TB# sh mo
Mod Ports Module-Type                       Model               Status
1    0      Cisco Nexus1010 Chassis           Nexus1010           active *
Mod Sw                Hw
1    4.2(1)SP1(2)      0.0
Mod MAC-Address(es)                         Serial-Num
1    00-19-07-6c-5a-a8 to 00-19-07-6c-62-a8 NA
Mod Server-IP        Server-UUID                           Server-Name
1    10.1.30.53       NA                                    NA
Nexus 1010 - Secondary
switch# sh sys red st
Redundancy role
      administrative:   secondary
         operational:   secondary
Redundancy mode
      administrative:   HA
         operational:   None
This supervisor (sup-2)
    Redundancy state:   Active
    Supervisor state:   Active
      Internal state:   Active with no standby
Other supervisor (sup-1)
    Redundancy state:   Not present
switch# sh module
Mod Ports Module-Type                       Model               Status
2    0      Cisco Nexus1010 Chassis           Nexus1010           active *
Mod Sw                Hw
2    4.2(1)SP1(2)      0.0
Mod MAC-Address(es)                         Serial-Num
2    00-19-07-6c-5a-a8 to 00-19-07-6c-62-a8 NA
Mod Server-IP        Server-UUID                           Server-Name
2    0.0.0.0          NA                                    NA
* this terminal session

Prasad,
This means that there is some sort of a communication issue between the two Nexus 1010 switches in the control VLAN. You should probably check the upstream configuration on the ports that connect to the 1010 links carrying the control traffic and also the links involved in the control path.
Thanks,
Shankar

Out-of-Band provisioning issue

Hi there,
I'm migrating from Configmanager 2007 to 2012 SP1 at a customer.
With CM 2007 I'd succesfully implemented Out-of-band management. Now I'm having some issues with provisioning AMT from CM2012.
The testing machines have never been provisioned with CM2007.
The oobmgmt.log at the client logs succesful activated the device.
At the server in the amtopmgr.log file the follwoing error is logged:
Error: Can NOT get OTP from target device (MachineId = 16777220)
I know this has to do with a one time password that is generated...I dont know where I have to look to resolve this issue.
Part of the amtopmgr logfile:
>>>>>>>>>>>>>>>Provision task (In Band Provision) begin<<<<<<<<<<<<<<<   SMS_AMT_OPERATION_MANAGER   28-10-2013 13:34:23
5268 (0x1494)
Provision target is indicated with SMS resource id. (MachineId = 16777220 DSK-0925.water.intern)   SMS_AMT_OPERATION_MANAGER   28-10-2013 13:34:23   5268 (0x1494)
Found valid basic machine property for machine id = 16777220.   SMS_AMT_OPERATION_MANAGER   28-10-2013 13:34:23   5268 (0x1494)
Warning: Currently we don't support mutual auth. Change to TLS server auth mode.   SMS_AMT_OPERATION_MANAGER   28-10-2013 13:34:23   5268 (0x1494)
The provision mode for device DSK-0925.water.intern is 1.   SMS_AMT_OPERATION_MANAGER   28-10-2013 13:34:23   5268 (0x1494)
The IP addresses of the host DSK-0925.water.intern are 10.10.128.76.   SMS_AMT_OPERATION_MANAGER   28-10-2013 13:34:23   5268 (0x1494)
Root hash of provisioning certificate is 2796BAE63F1801E277261BA0D77770028F20EEE4.   SMS_AMT_OPERATION_MANAGER   28-10-2013 13:34:23   5268 (0x1494)
Attempting to establish connection with target device using SOAP.   SMS_AMT_OPERATION_MANAGER   28-10-2013 13:34:23   5268 (0x1494)
Create provisionHelper with (Hash: FD16D8C6A482C73C12832BC19D5BCABD4460D5A3)   SMS_AMT_OPERATION_MANAGER   28-10-2013 13:34:23   5268 (0x1494)
Set credential on provisionHelper...   SMS_AMT_OPERATION_MANAGER   28-10-2013 13:34:23   5268 (0x1494)
Try to use provisioning account to connect target machine 10.10.128.76...   SMS_AMT_OPERATION_MANAGER   28-10-2013 13:34:23   5268 (0x1494)
Core version of target machine 10.10.128.76 is: 9.0.3.   SMS_AMT_OPERATION_MANAGER   28-10-2013 13:34:24   5268 (0x1494)
Succeed to connect target machine 10.10.128.76 using provisioning account #0.   SMS_AMT_OPERATION_MANAGER   28-10-2013 13:34:24   5268 (0x1494)
GeneralInfo.GetProvisioningState finished with HResult = 0x0, status = 0x0, clientErr = 0.   SMS_AMT_OPERATION_MANAGER   28-10-2013 13:34:24   5268 (0x1494)
Get device provisioning state is In Provisioning   SMS_AMT_OPERATION_MANAGER   28-10-2013 13:34:24   5268 (0x1494)
Error: Can NOT get OTP from target device. (MachineId = 16777220)   SMS_AMT_OPERATION_MANAGER   28-10-2013 13:34:25   5268 (0x1494)
CStateMsgReporter::DeliverMessages - Queued message: TT=1201 TIDT=0 TID='Unspecified' SID=13 MUF=0 PCNT=1, P1='DSK-0925.water.intern' P2='' P3='' P4='' P5=''   SMS_AMT_OPERATION_MANAGER   28-10-2013 13:34:25   5268
(0x1494)
CStateMsgReporter::DeliverMessages - Created state message file: C:\Program Files\Microsoft Configuration Manager\inboxes\auth\statesys.box\incoming\ikjsq3c0.SMX   SMS_AMT_OPERATION_MANAGER   28-10-2013 13:34:25
5268 (0x1494)
>>>>>>>>>>>>>>>Provision task (In Band Provision) end<<<<<<<<<<<<<<<   SMS_AMT_OPERATION_MANAGER   28-10-2013 13:34:25
5268 (0x1494)
Anyone has a good idea?
Thanks in advance.
Mark

Hi Mark,
I am experiencing the same issue you are, but only with one machine. I have over 1000 machines that have successfully provisioned, so it's a bit of a mystery at the moment.
I have confirmed that my failing machine does have a OTP in the SCCM database by running the following query:
select MachineID ,OTP from dbo.AMT_MachineProperties where HostName = '<machine name>'
This shows a OTP for each machine, but I'm still having trouble with this one. Did you ever find a solution?
Thanks,
Russel

Out-of-Band SMASH Library Event ID 4509 (SCOM 2012SP1UR3)

Hi!
I´m using the "Microsoft System Center Out-of-Band SMASH Library" 7.0.8707.0 found here:
http://blogs.technet.com/b/momteam/archive/2012/04/02/ws-management-smash-device-discovery-template-released.aspx
It is a reqiurement for some of DELLs MP:s.
After creating a working (as it seems) discovery with the template, Event ID 4509 is logged with irregular intervals:
The constructor for the managed module type "Microsoft.EnterpriseManagement.Mom.DatabaseQueryModules.GroupCalculationModule" threw an exception. This module was running in rule "Microsoft.SystemCenter.OOB.2cf63b4c061f4a67bac712ed75a57916.PoolManagesSMASHDevice.Discovery"
running for instance "Network Monitoring Resource Pool" with id:"{E9178425-9B5C-85C1-E1DF-7E440E2E9FBF}" in management group "OMGROUP".
The id “e9178425-9b5c-85c1-e1df-7e440e2e9fbf” is the "Network Monitoring Resource Pool", which is also the pool chosen for the discovery.
I´ve also noticed that the initial discovery is carried out by the "All Management Servers Resource Pool", but then monitoring seem to be done by "Network Monitoring Resource Pool", but I don´t know if that is important:
I don´t know what problems that can arise from this error, but it´s disturbing.
Anyone else using this feature and seen or not seen the same?
Regards
Peter

To fix your issue, refer to below link
http://www.briandeyo.us/brd/wp/index.php/2009/10/08/operations-manager-not-sending-email-after-im-notification-settings-changed-event-id-4509
Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question, please click "Mark As Answer".

Cisco VM server based ISE deployment in out of Band

Hi,
can any one please share the link of Configuration guide for VM based Cisco ISE in out of band deployment model.
Regards,
Awais

Hi,
can any one please share the link of Configuration guide for VM based Cisco ISE in out of band deployment model.
Regards,
Awais

Is it possible to have 2500 series management interface out of band of APs?

I currently have 2500 series WLCs. Our wireless network is completely separate from our internal network, keeping the WLC from talking to any internal servers. The company would like to start using AD(LDAP authentication) for end users while still keeping the APs on a completely separate network. Since the 2500 series does not support a "service port", Is there any way to move the management port out-of-band with no access to APs and just use the other ports for AP management?

I haven't had my morning coffee ... But let me give this a shot..
I am going to say no. The managment interface is needed for APs to join. If you isloate this interface no APs can join. Even if AP managers are used, the AP requries to touch the managment interface when booting up.
"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
‎"I'm in a serious relationship with my Wi-Fi. You could say we have a connection."
"Im like bacon, I make your wireless better"

Nexus 1010, out of band

Similar Messages

Maybe you are looking for