Nexus 5595 7.0(5)N1(1) - Config Sync / CFS Issue

Hello,
Posting this fix as it may help anyone facing the same issue.
We recently installed 2 x Nexus 5596 into our DC with the management connections running across 6500 VSS switches. We have the same setup in another DC and all worked fine. However, with the new installation we upgraded to 7.0(5)N1(1) and hit a problem with the config-sync not working across the mgmt0 interfaces. However, the Peer was reachable over mgmt0 as VPc was up and we could ping / SSH no problem.
We also have the necessary ‘cfs ipv4 distribute’ enabled. Output of issue below:
switch-profile : Tcprofile
Peer-IP-address            : 192.168.1.28
Peer-sync-status           : Not yet merged
Merge Flags: pending_merge:1 rcv_merge:0 pending_validate:0
Peer-status                : Peer not reachable
We tried various things such as removing the ‘cfs ipv4 distribute’ and re-enabling but this didn't fix the problem. So spoke to a Cisco engineer who suggested the 6500 could be blocking multicast and therefore stoppping CFS traffic across our management Vlan. Apparently there have been some changes to CFS in the latest NXOS.
So the fix was simple in the end. We just enabled PIM on our 6500 SVI and Config Sync sprang into life. See below:
interface vlan x
description Management Vlan
ip pim sparse-dense-mode
Hope this helps

Hi, I have upgraded from 5.2.1.N1.4 to 7.1.0.N1.1b.
There were many bugs.
I found we can't upgraded to 7.1.0 from NX-OS prior to 7.0 in Cisco official.
So, I have upgraded to 7.0.5N1.1 then to 7.1.0N1.1b.
In result, some part of startup-config such as logging server is lost.
I'm going to try to upgrade in same process a few times.
Sincerery

Similar Messages

Config-sync on Nexus 7k?

I'm using configuration synchronization on my Nexus 5k pair. But I've got a couple of Nexus 7k switches on the horizon.
But I can't seem to find anything about config-sync being supported on the 7k platform. Is anyone using config-sync on the Nexus 7k platform??
Thanks.

I don't think this is a supported feature on the Nexus 7000's.
HTH,
Manny.

Nexus 5K Config-Sync : Things to look out for

I've looked through the Cisco config guides for setting up Config sync and have successfully used it to configure dual-homed FEX's ports.
Is there anything I should be aware of that can cause issues?
I enabled config sync on an existing pair of 5Ks. In other words, the 5Ks already have existing configurations on them before I enabled config sync.

Hi,
According to the this link, you still have to configure the single port in switch profile. Config sync is used when your devices are connected to both 5ks, so you don't have configure the same thing twice. If your device is going to be singly attached, there is no need for config sync.
Guidelines and Limitations
The guidelines for configuration synchronization are as follows:
•You must configure the following interfaces in a switch profile:
–Port-channel interfaces
–Ports that are not channel-group members
•You must configure all port-channel members outside the switch profile in configuration terminal mode.
•You must follow configurations in a specified order.
•Depending on the type of vPC topology (active/active or straight-through) and the type of configuration that is needed (port channel, nonport channel, FEX, QoS, and so on), you must use the switch profile mode or the configuration terminal mode. See the "At-A-Glance Configuration Modes" section to identify what mode is used for different types of configurations.
Configuration synchronization has the following configuration limitations:
•FCoE in vPC Topologies—FCoE configurations are not supported in switch profiles because configurations are typically different on peer switches. If you enable FCoE on a vPC peer switch, you must not configure the port channel in the switch profile.
• Feature Commands—The feature feature name commands that enable a conditional feature are not supported in switch profiles. You should independently configure these commands on each peer switch in configuration terminal mode.
•Configuration Rollback and Conditional Features—With configuration synchronization, when a conditional feature is present in a checkpoint and not in the running configuration, a configuration rollback to that checkpoint fails. The workaround is to reconfigure the conditional feature ("feature xyz") before the configuration rollback is executed. This workaround also applies to the vpc domain command and the peer-keepalive command in vpc-domain mode.
link:
http://www.cisco.com/en/US/docs/switches/datacenter/nexus5000/sw/operations/n5k_config_sync_ops.html#wp1035414
HTH

Nexus 5548 acl in config sync

Hello, I have a following problem. When configuring ip acl in config-sync mode I get following message: "Error: Cannot configure acl rule without seq no." Is this a bug or a feature? I'm running 5.1(3)N1(1)

sounds more like a bug. i see a bug being filed on it internally (not customer viewable yet). CSCtz27923. I will make it customer viewable shortly.
thanks, vinayak

Config-sync issue in Nexus5K

Hello
I am trying to add a vlan to my pair of Nexus 5K with the confi-sync, but I recieve a really strange error comming from the peer switch
switch-profile : S1-S2
Peer-IP-address            : x.x.x.2
Peer-sync-status           : In sync
Peer-status                : Commit Failure
Peer-error(s)              : Invalid username: user does not exist
Does anybody know what does it mean ?
Thank you in advance
Regards
Lucas

My guess is that on the other Nexus switch the username/password/privilege information is different. Check out this document that has a lot of details on config-sync and the ways it can go wrong...
http://www.cisco.com/en/US/docs/switches/datacenter/nexus5000/sw/operations/n5k_config_sync_ops.html#wp1051910
Hope it helps
Peter

Is anyone else having Config error 16 issue when trying to start PSE 12 or Premier Elements after Mac upgrade to Yosemite 10.10 on iMac

Is anyone else having Config error 16 issue when trying to start PSE 12 or Premier Elements 12 after the Mac upgrade to OS X Yosemite 10.10 on iMac. I have had a number of issues with software and things after upgrading to OS X Yosemite 10.10 and even 10.10.1. I have uninstalled and reinstalled both PSE 12 and Premier Elements 12 a number of times and everything goes fine until its ready to launch and then you get an error message. Numerous uninstalled and reinstalls don't removing the problem. Strangely enough PSE 11 still appears to boot up and I never owned Premier Elements 11 so I don't know if it will start. I thought with Apple dropping its Apeture software and greater integration of iPhoto and Apeture files into Lightroom 5.7 all would be harmonious between these two players. Im not sure where Adobe wants us to go it recently removed the plugin to allow you to update files from LR to Adobe Revel, whats up with that. I now own two version of Adobe software that no longer work with my Mac and now way of uploading pictures from Lightroom to Revel. Needless to say I am pretty reluctant to sign on to a subscription of Creative Cloud with long term financial obligations when I can't even get my current Adobe software to work independently much less integrate with Lightroom. Frustrated with it all!

Get rid of 'put disks to sleep when possible' and you may see a dramatic improvement (not necessarily a cure).
That specific problem is a multiple-Processor (including graphics processor) problem, where one of the processors lost track of whether it should be responding to interrupts. You may have a Hardware problem.

ACE Switchover and Config Sync

Hi
I'm new to the ACE modul and trying to set up some szenarios and i run already into some troubles.
Question 1)
I configured redundancy to another module - virtulised mode. Config sync between the context worked fine. If i change s'thing in the activ context it was copied to the standby context. But if i changed something in the active Admin context it was not copied to the standby Admin context.
Question 2)
FT Switchover in the Admin context is not possible returns the following fault:
ACE_Switch08/Admin# ft switchover
This command will cause card to switchover (yes/no)? [no] yes
Invalid FT group. FT switchover command will be ignored.
ACE_Switch08/Admin#
If I switch a single FT group it works. But how is it possible to switch all FT groups a the same time? Do i have to switch each context by itself?
Question 3)
After i have switched the active context to the standby context, the ft group x command shows both peers as active. After i take the standby ft group no inservice and back inservice it shows correctly Active and standby_HOT.
The configuration:
hostname ACE_Switch08
boot system image:c6ace-t1k9-mz.3.0.0_A1_4a.bin
resource-class RC1
limit-resource all minimum 10.00 maximum equal-to-min
class-map type management match-any REMOTE_ACCESS
description -- Remote Access traffic match --
2 match protocol telnet any
3 match protocol ssh any
4 match protocol icmp any
policy-map type management first-match REMOTE_MGMT_ALLOW_POLICY
class REMOTE_ACCESS
permit
interface vlan 2100
ip address 172.29.190.16 255.255.255.0
service-policy input REMOTE_MGMT_ALLOW_POLICY
no shutdown
ft interface vlan 2020
ip address 192.168.100.1 255.255.255.0
peer ip address 192.168.100.2 255.255.255.0
no shutdown
ft peer 1
heartbeat interval 200
heartbeat count 20
ft-interface vlan 2020
ip route 0.0.0.0 0.0.0.0 172.29.190.1
context sf0-2200
allocate-interface vlan 2201
allocate-interface vlan 2207
member RC1
context sf0-2220
allocate-interface vlan 2221
allocate-interface vlan 2227
member RC1
ft group 1
peer 1
no preempt
priority 200
peer priority 150
associate-context sf0-2200
inservice
ft group 2
peer 1
no preempt
priority 200
peer priority 150
associate-context sf0-2220
inservice
username admin password xxx role Admin domain
default-domain
username www password xxx role Admin domain de
fault-domain
Any help is appreciated
pat

Hi Pat,
1)
for my config i just put the "user" or "backend" contexts into ft groups. I don't sync the admin contexts on both aces. I am not even sure if that makes sense or is "best practicse".
So if you don't put the admin context into an extra ft group it won't be synced. you have to configure the admin contexts on each physical ace separately.
Putting the contexts sf0-2200 & sf0-2220 into an ft group and not having an ft group for admin is the way to go IMHO.
2)
If you do a switchover you always have to specify which context you want to switchover. I don't think that you can actually switchover a whole bunch of contexts with this command. If you want to do that a reload is the only way AFAIK.
Try:
ft switchover 1
ft switchover 2
3)
This could be because you have not configured the other ACE's admin context to participate in the ft properly.
My configs looke like this.
ACE01:
ft interface vlan 777
ip address 172.16.99.1 255.255.255.252
peer ip address 172.16.99.2 255.255.255.252
no shutdown
ft peer 1
heartbeat interval 200
heartbeat count 20
ft-interface vlan 777
query-interface vlan 444
ft group 3
peer 1
priority 150
peer priority 110
associate-context FOO
inservice
ft group 4
peer 1
priority 150
peer priority 110
associate-context BAR
inservice
ft group 2
peer 1
priority 150
peer priority 110
associate-context FOO-BAR
inservice
ACE02:
ft interface vlan 777
ip address 172.16.99.2 255.255.255.252
peer ip address 172.16.99.1 255.255.255.252
no shutdown
ft peer 1
heartbeat interval 200
heartbeat count 20
ft-interface vlan 777
query-interface vlan 444
ft group 2
peer 1
no preempt
priority 110
peer priority 150
associate-context FOO
inservice
ft group 3
peer 1
no preempt
priority 110
peer priority 150
associate-context BAR
inservice
ft group 4
peer 1
no preempt
priority 110
peer priority 150
associate-context FOO-BAR
inservice
Hope that helps
Roble

Problem with config sync between two CSM-S modules

Hi everybody,
I have a problem with config sync between two CSM-S modules.
I am using CSM-S software version 2.1(8).
The acitve module is used in a 6509 with WS-SUP720-BASE supervisor running software version 12.2(18)SXF12a.
The standby module is used in a 6509-V with VS-S720-10G supervisor (no VSS setup) running software version 12.2(33)SXI3.
Failover seems to work fine:
switch-active#sh modu csm 2 ft
FT group 1, vlan 398
This box is active
Configuration is out-of-sync
priority 150, heartbeat 3, failover 40, preemption is on
switch-standby# sh modu csm 2 ft
FT group 1, vlan 398
This box is in standby state
Configuration is out-of-sync
priority 80, heartbeat 3, failover 40, preemption is on
The command (on active side) "hw-module contentSwitchingModule 2 standby config-sync" leads to following result:
switch-active:
2010-04-14T16:21:45+02:00 srz16-1b.net.dsh.at/srz16-1b.net.dsh.at 56042: Apr 14 16:21:44.223: %CSM_SLB-6-REDUNDANCY_INFO: Module 2 FT info: Active: Bulk sync started
2010-04-14T16:21:45+02:00 srz16-1b.net.dsh.at/srz16-1b.net.dsh.at 56043: Apr 14 16:21:44.251: %CSM_SLB-6-REDUNDANCY_INFO: Module 2 FT info: Active: Sending configurations to Standby CSM, this may take several minutes!
2010-04-14T16:21:46+02:00 srz16-1b.net.dsh.at/srz16-1b.net.dsh.at 56044: Apr 14 16:21:45.995: %CSM_SLB-6-REDUNDANCY_INFO: Module 2 FT info: Active: Sending configuration to Standby CSM
2010-04-14T16:21:51+02:00 srz16-1b.net.dsh.at/srz16-1b.net.dsh.at 56045: Apr 14 16:21:50.831: %CSM_SLB-6-REDUNDANCY_INFO: Module 2 FT info: Active: Sending configuration to Standby CSM
2010-04-14T16:21:57+02:00 srz16-1b.net.dsh.at/srz16-1b.net.dsh.at 56046: Apr 14 16:21:56.151: %CSM_SLB-6-REDUNDANCY_INFO: Module 2 FT info: Active: Sending configuration to Standby CSM
2010-04-14T16:22:59+02:00 srz16-1b.net.dsh.at/srz16-1b.net.dsh.at 56047: Apr 14 16:22:58.791: %CSM_SLB-3-REDUNDANCY: Module 2 FT error: Active: Manual bulk sync timed out
2010-04-14T16:22:59+02:00 srz16-1b.net.dsh.at/srz16-1b.net.dsh.at 56048: Apr 14 16:22:58.803: %CSM_SLB-3-REDUNDANCY: Module 2 FT error:
2010-04-14T16:22:59+02:00 srz16-1b.net.dsh.at/srz16-1b.net.dsh.at 56049: FT CONFIG SYNC: Failed config sync entity send
switch-standby:
2010-04-14T16:21:45+02:00 srz31-5a.net.dsh.at/srz31-5a.net.dsh.at 2475: Apr 14 16:21:44.232: %CSM_SLB-6-REDUNDANCY_INFO: Module 2 FT info: Standby: Bulk sync started
2010-04-14T16:21:45+02:00 srz31-5a.net.dsh.at/srz31-5a.net.dsh.at 2476:
2010-04-14T16:21:45+02:00 srz31-5a.net.dsh.at/srz31-5a.net.dsh.at 2477: Apr 14 16:21:44.240: %CSM_SLB-6-REDUNDANCY_INFO: Module 2 FT info: STANDBY:Configuration is being received, This may take several minutes!
2010-04-14T16:21:49+02:00 srz31-5a.net.dsh.at/srz31-5a.net.dsh.at 2478: Apr 14 16:21:48.824: %CSM_SLB-6-REDUNDANCY_INFO: Module 2 FT info: Standby: Receiving configuration from Active CSM
2010-04-14T16:21:54+02:00 srz31-5a.net.dsh.at/srz31-5a.net.dsh.at 2479: Apr 14 16:21:53.964: %CSM_SLB-6-REDUNDANCY_INFO: Module 2 FT info: Standby: Receiving configuration from Active CSM
2010-04-14T16:21:59+02:00 srz31-5a.net.dsh.at/srz31-5a.net.dsh.at 2480: Apr 14 16:21:58.852: %CSM_SLB-6-REDUNDANCY_INFO: Module 2 FT info: Standby: Started clearing configuration
2010-04-14T16:21:59+02:00 srz31-5a.net.dsh.at/srz31-5a.net.dsh.at 2481: Apr 14 16:21:59.400: %CSM_SLB-4-REDUNDANCY_WARN: Module 2 FT warning: Standby: Config Sync does not save running-config to startup-config
2010-04-14T16:22:00+02:00 srz31-5a.net.dsh.at/srz31-5a.net.dsh.at 2482: Apr 14 16:21:59.400: %CSM_SLB-6-REDUNDANCY_INFO: Module 2 FT info: Standby: Previous configuration are being deleted from supervisor
The last log message on standby device seems to be correct - there is no CSM configuration after the attempted config sync.
Our configuration includes about 3500 lines and it is really uncomfortable to keep in sync manually.
Maybe someone has the same problem?
kind regards,
Christoph

Hi Christoph,
I am running into the exact same issue. Upon further investigation I've discovered that this is a known bug, CSCtd09117. You can read more about it here: http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCtd09117 . Apparently this is fixed in ver 12.2(32.8.11)SX323 .
I haven't had a chance to upgrade yet, so I can't verify the fix, but if it works for you please let me know.
Regards,
Brandon

CSM config-sync in bridge mode?

We are planning to upgrade our CSM from 4.1.6 to 4.2.6 and wanted to be able to utilize the config-sync capabilites in the new code. First, is config-sync supported in bridge mode and has anyone had much success or problems? We weren't able to find documentation on this? Please help!

config-sync works with bridge mode and routing mode.
You might want to go to 4.2.7 due to this ddts :
CSCse65938: CSM config-sync causes standby csm to core dump
Also, make sure your IOS version is at the right level due to this
CSCej00341: CSM Configuartion Sync timing out for large configurations
Gilles.

Getting "File copy Config Sync Failed. Commit unsuccessful! " on CSS-11155

Getting a strange error "FILE copy Config Sync Failed. Commit unsuccessful!" from the following and I am not sure what it exactly means:
cce01-c35-in# sh app
APP CONFIGURATION:
Enabled PortNumber: 5001 MaxFrameSize: 10240
cce01-c35-in# sh app session
App Session Information 'no hostname':
Session ID: 839f0990 IP Address: 10.10.10.2 State: APP_SESSION_UP
css-c09-nz# commit_redundConfig "10.10.10.2"
Verifying app and redundancy configs ... -
Checking local and remote switch versions ...|
Checking Backup app session up.... \
Checking redundancy state.... -
Working /
Waiting for completion signal from remote switch .../
Verifying running-config copy success ...-
File copy Config Sync Failed. Commit unsuccessful!
localconfig: 6238 bytes
remoteconfig : 6150 bytes
css-c09-nz#

there is at least one know bug :
CSCdx89818 - config sync fails
I could not check if this applies to you since you did not provide your version.
This bug was fixed in the following release :
006.010(000.004) 05.3(00.18)S 05.0(00.54)S 05.10(01.03)S
Gilles.

DHCP Failover Auto Config Sync

Downloaded most current version of script and set it up in lab. It works but the log file (.\dhcpautosynclogfile.txt) is growing at a fast rate. Entries for sync complete and automatically sync again are being posted at rate of 3 or 4
times per second.

Script is the DHCP Failover Auto Config Sync script.
Questions is - why is log file filling at such an alarming rate ?
And what script is that? Who wrote it? Have you contacted the author?
Believe it or not, we haven't heard of every script ever written. =]
EDIT: Is this what you're referring to?
http://gallery.technet.microsoft.com/scriptcenter/Auto-syncing-of-configurati-6eb54fb0
If so, post your question on the QandA tab so the author will see it.
Don't retire TechNet! -
(Don't give up yet - 12,830+ strong and growing)

CSM-S SSL daughtercard config sync

Hi there,
First Question
Is it possible to do a config sync for the CMS-S SSL daughtercard ?? On the SSL daughtercard of the standby CSM is no config _
Second Question
How can we built up an redundent configuration (FT) with the CSM-S SSL daughtercard ??
In our actual configuration the CSM works in active - standby mode.
Thanks a lot
Dirk Barnekow

No, you cannot config sync for the CMS-S SSL daughtercard

5548 Config Sync issue - Suspended by vPC

I have 2 UCS 6120 fabric interconnects which both have VPCs to 2 x 5548s. First fabric interconnect uses Po260 & vPC 260 and second fabric interconnect uses Po261 & vPC 261.  I used config sync to add "spanning-tree port type edge trunk" to int po 260 & 261. The commit worked properly, peers are in sync, etc. The problem is when I committed the command, int po 260 & 261 on the secondary 5548 went into "suspended by vPC". I can't figure out why they did this, the configurations are the same and all vPC consistency checks pass. To fix the issue, all I had to do was bounce the port-channel on the secondary 5548 (shut/no shut) after which it came back online. I only did this to Po260 so Po261 is still down so that I can troubleshoot further. Please see below:
vPC domain id                     : 70
Peer status                       : peer adjacency formed ok
vPC keep-alive status             : peer is alive
Configuration consistency status : success
Per-vlan consistency status       : success
Type-2 consistency status         : success
vPC role                          : secondary
Number of vPCs configured         : 7
Peer Gateway                      : Disabled
Dual-active excluded VLANs        : -
Graceful Consistency Check        : Enabled
Auto-recovery status              : Disabled
vPC Peer-link status
id   Port   Status Active vlans
1    Po255 up     1,10-13,26-29,151-156,180-181,200,318,331,399-417,
                   419-422,424-431,433-436,438-443,446-448,450,452-45
                   3,455-458,460-465,467-471,480-494,498-499,503,602-
                   633,644-657,659,663-664,698-701,800,805,850-851,89
                   0-891,899-904,906,908,912-950,952-958,975,987-988,    ....
vPC status
id     Port        Status Consistency Reason                     Active vlans
171    Po171       up     success     success                    1,10-13,26-
                                                                 29,151-156,
                                                                 180-181,200
                                                                 ,318,331,39
                                                                 9-417,41....
260    Po260       up     success     success                    10-13,26-29
                                                                 ,663-664,89
                                                                 0-891
261    Po261       down* success     success                    -
sh int po 261
port-channel261 is down (suspended by vpc)
Any help would be appreciated

Yes, I did check that and all parameters match as follows:
5548-2# sh vpc consistency-parameters int po 261
    Legend:
        Type 1 : vPC will be suspended in case of mismatch
Name                        Type Local Value            Peer Value
Shut Lan                    1     No                     No
STP Port Type               1     Edge Trunk Port        Edge Trunk Port
STP Port Guard              1     None                   None
STP MST Simulate PVST       1     Default                Default
lag-id                      1     [(7f9b,                [(7f9b,
                                  0-23-4-ee-be-46, 8105, 0-23-4-ee-be-46, 8105,
                                   0, 0), (8000,          0, 0), (8000,
                                  0-5-73-d4-d5-fc, 1, 0, 0-5-73-d4-d5-fc, 1, 0,
                                   0)]                    0)]
mode                        1     active                 active
Speed                       1     10 Gb/s                10 Gb/s
Duplex                      1     full                   full
Port Mode                   1     trunk                  trunk
Native Vlan                 1     10                     10
MTU                         1     1500                   1500
Admin port mode             1
Allowed VLANs               -     10-13,26-29,663-664,89 10-13,26-29,663-664,89
                                  0-891                  0-891
Local suspended VLANs       -     -                      -

CSS11501 Hangs during Config Sync

We have CSS11501 boxes in redundancy mode. Until now, the config sync process happened without any issues. For the last two occassions, the CSS hangs completely during manually initiated config sync thereby bringing down all active connections..After the sync is completed, the box returns back to normal.
The only changes made in recent time is the Redundancy config (failover from master to backup forcefully)..
Any know issues on the following bundle:-
Version: sg0810002 (08.10.0.02)
Flash (Locked): 07.40.0.04
Flash (Operational): 08.10.0.02
Type: PRIMARY
Licensed Cmd Set(s): Standard Feature Set

Hi, I will check to see if your are hitting any know issue but let me tell you that 8.10.002 is the first release of 8.10 code and we have 8.10.301 already which would be the best way to go at this point.
I will update you with any know issue. It would be useful to see the showtechs when the issue is showing u.
Also when you say that hangs completely:
would no respond to ping to the VLAN IP?
is it accesible via telnet or ssh?
is it accesible via console?
What kind of redundancy are you using? do you see any failover at the time of the problem?
Can you show me the syntax you are using to sync the config?.

7940 Config and flash issues

Hi, i'm hoping somebody can please help me.
I have been using VOIP via a softphone for a couple of years now, I decided that I wanted to have a go at setting up a Cisco phone. So I have got a 7940G second hand which works fine. I am a home user trying to learn so I am using a BT Homehub with dynamic IP and SIP on voip-talk.org
The phone was still configured form the previous owner with subnet, DNS, FTP, VLAN etc. I couldn't find a how to edit these settings, so I thought if I set it back to factory defaults, told it to delete network cfg. I thought on restarting it might ask me to input the detail? but it showing "configuring VLAN" and then constantly stays on "configuring IP"
although it stills picks up an IP via DHCP and I can ping it ok, I can also browse on to the web interface which show the following info
DEVICE INFO:
MAC Address 00137FA9D10B
Host Name SEP00137FA9D10B
Phone DN
App Load ID P00307020400
Boot Load ID PC0303010100
Version 7.2(4.0)
Expansion Module 1
Expansion Module 2
Hardware Revision 4.4
Serial Number INM09101LK3
Model Number CP-7940G
Codec ADLCodec
Amps 5V Amp
C3PO Revision 2
Message Waiting NO
NETWORK CONFIG:
DHCP Server 192.168.1.254
BOOTP Server Yes
MAC Address 00137FA9D10B
Host Name SEP00137FA9D10B
Domain Name home
IP Address 192.168.1.68
Subnet Mask 255.255.255.0
TFTP Server 1
Default Router 1 192.168.1.254
Default Router 2
Default Router 3
Default Router 4
Default Router 5
DNS Server 1 192.168.1.254
DNS Server 2
DNS Server 3
DNS Server 4
DNS Server 5
Operational VLAN Id
Admin. VLAN Id
CallManager 1
CallManager 2
CallManager 3
CallManager 4
CallManager 5
Information URL
Directories URL
Messages URL
Services URL
DHCP Enabled No
DHCP Address Released Yes
Alternate TFTP Yes
Erase Configuration NO
Forwarding Delay YES
Idle URL
Idle URL Timer 0
Authentication Url
Proxy Server Url
PC Port Disabled YES
SW Port Configuration AUTO
PC Port Configuration AUTO
TFTP Server 2
User Locale
Network Locale
Handset Only Mode No
User Locale Version
Network Locale Version
GARP Enabled Yes
Voice VLAN Enabled Yes
Auto Line Select Enabled No
Video Capability Enabled No
DSCP For Call Control default
DSCP For Configuration default
DSCP For Services default
Security Mode Non Secure
Web Access Enabled
Connection Monitor Duration 0
PC VLAN
Basically I need to know first all how to at least change the settings, as I don't have access via the phone itself or the web interface. And I will probibly also need to reflash the firmware with something that will do SIP.
Thanks for looking and your help

Hi
I think the main issue you have with this phone is that its not picking up a TFTP server IP address and therefore cannot download any configuration details.
As a start i'd check that the IP address range that it has got via DHCP has an option 150 setup to your CUCM TFTP server.
Once its got this, if you have auto registration setup if should at least boot up
Hope this helps
PKS

Nexus 5595 7.0(5)N1(1) - Config Sync / CFS Issue

Similar Messages

Maybe you are looking for