Nexus 7010 Loses Config after power off

Recently we installed a pair of Nexus 7010's and we recently moved them to an APC rack better suited for their size. Upon powering them up we found out that the VDC's lost their configurations. The VDC's and the alloated resources were still there as well as the default VDC configuration but the other 2 we have configured had their configurations missing. We have been observing best practices and saving the configuration to NVRAM with the copy run start comand as well as the copy run start vdc-all commands yet the configurations were still lost.
Can anyone shed some light on what the problem may be?
Thank you in advance for your help!

We had the same issue TAC told us to reset the supv
,,,,, you might want to save your config ;-) it worked for us

Similar Messages

C871 default config after power off - bad nvram?

Hello,
I have new C871 with default configuration. after reconfiguring and reload, my config is loaded from nvram. But after power off, is there default configuration. What's wrong? config register is set to 0x2102 (that's ok).
any ideas?
thanks, 
martin

I found the reason - construction 'bug'. reset button was always presset.

RV042 v3 (v4.2.2.08) loses config after power loss

I have two RV042 units - both v3 hardware and both with firmware 4.2.2.08.
Both units lose thier configuration and return to factory default after a power loss.
I've tried re-flashing the firmware in both units - no change.
I have the configuration backed up for both units, so it only takes me a few moments to restore them after a power loss, but shouldn't the units hold their configuration in NVRAM or some such?
Any ideas as to what I'm missing?
Thanks for any replies...
-- Ray --

Well the date set back to 1969 is a classic sign of a dead battery.
Check out things in Texas Mac Man's Battery, PRAM, PMU tutorial on the subject. His tutorial is a little dated (don't believe it even mentions G5's, or Intel Macs) but the info in it, except SMU and SMC not being included, still applies. Luck ! DALE

IPad WEP password required after power off.

Hi,
On my ipad mini I am required to re-enter my WEP password after power off.
Why is this and how do I prevent it from happening?
This does not occur on my mbp or iphone 4s.
Thanks,
Rob.

Although it should work flawlessly, for some reason mobile devices don't always play nice with WEP. You're far better off with WPA2 (security-wise) anyway. If you have the ability to change your network's security, it might be easier to just get away from WEP than to try to make your mini work with it.

HT4623 Hello! Answer Why do not open pictures after power-off at iphone 3? Thank you!

Hello! Answer Why do not open pictures after power-off at iphone 3G? Thank you!

This problem is already two years.

Linksys SGE2010P resets after power off

Hello,
i got a linksys SGE2010P and when i configure it and save it works fine but after a power off the settings are back to default. someone an idea ?
Rensk,
Solved!
Go to Solution.

i used to have the same problem in my SFE2000 until I have learned that you need to do the following steps to permanently save your settings
go to Admin > File Management > Copy Files
click on Copy Configuration button
set Source File Name as Running Config
set Destination File Name as Startup Config
click Apply

LAP1142 looses config after power cycle

We have some 1242 LAPs in a two 5508 controller setup working fine. All LAP are configured to obtain address from DHCP. After first join we usually change some configs like HOSTNAME, AP GROUP, PRIMARY AND SECONDARY WLC. After a software restart or a complete power off/power on the LAPs joins the primary controller and all configuration still there. We now add a 1142 LAP and is does not retain the configuration after a power off/power on cycle, but after a software restart there is no problem. The only way to retain the config is setting the AP with a static IP address.
We use WLC 7.0.116 and we see no errors in the LAP console.
Best Regards,
Augusto

I would just open a tac case as it might be an issue with the APs itself.
Sent from Cisco Technical Support iPad App

Lose settings after power cycle.

I noticed the iPhone (firmware 1.1.1) will occassionally lose internet WAP settings for my carrier after power cycling (turning off then back on). The top left menu displays the correct wireless carrier and has the "E" for EDGE coverage but fails to access the network via EDGE for email/internet browsing due to the WAP settings are erased. I have to then enter the WAP settings again. Has anyone else experienced this?

I reinstalled my firmware but couldn't find a solution to this. After installing the latest firmware 1.1.2 I no longer experience the issue with the reset settings.

Resume music playlist after power off?

Just graduated from a 3G iPod to a 32gb 2nd gen iTouch. On my old iPod, I could listen to a playlist, power off in the middle, and the iPod would resume playback from that exact point.
This isn't happening with the iTouch.
Am I missing a setting? I've seen the threads about "resume playback" checkbox in iTunes, but that doesn's seem to work for related iTouch questions...
thx
barry

This is how the Zen operates, more or less. Under the current firmware, your place will be saved if you turned the Zen off for less than about an hour or two. This is because the Zen goes into a "sleep" mode. You can tell the Zen was in sleep mode if, when you turn it on, all you see is "Zen" and the player turns on in a second or two.
If the Zen has been off for more than an hour or two, it turns off completely. You can tell this because the screen shows "Creative", then "Zen", and takes about 5-7 seconds to boot up. In this case, the Zen will lose your place.
I agree that this is far from ideal, to say the least. I find myself having to navigate back to the right folder to get to the next track in my audio book all the time.
I understand that things were different with earlier firmwares, before they had the "sleep" mode. Hopefully they can fix this problem in a future firmware release.

Bad vi after power off

sometimes LV can't open VI if system crushed (power off) when this VI is opened by LV
this trouble appear not every time.
I had experimented with this trouble and not found any rule (about dozen attempts and no problem with vi)
But yesterday I was on customer object and system crushed (power off) twice. After second crush I had found that can't open main VI (attached).
This error was in LV6 (my first version), in LV7 fnd now in LV8 (8.3)
I'm not sure, but may by bad file is smaller than correct file (from backup).
Why this happen and how can I avoid this error?
Attachments:
data_processing.vi ‏231 KB

Hi Artem,
I would not call it a LV-error when you switch-off (or crash) your pc while working... How should LV prevent from crashing?
There is no other answer than 'save early and often'! And starting from LV8 there is an auto-save option similar to MS Office (save every x mins)!
Best regards,
GerdW
CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
Kudos are welcome

Lumia 625 wont start after power off!

I bought a lumia 625 5 months ago and it worked fine. but recently when i switch off power it wont turn back on. So i had do keep it in air plane mode at night. After like one hour it switches on back. I tried resetting and restarting. Phone only vibrates after i release power key ( in all resetting methods), but does not show anything in the display. How can i fix this. help would be appreciated

I'm going to suggest a hard reset of the phone. Do a backup first, then either go to Settings/About and select Reset my Phone, or for the 625:
Warning! All data will be lost!
1.Power off your phone
2.Press power button and after phone vibrates once press volume down until you will see exclamation sign on the screen
3.Press in this order:volume up
volume down
power
volume down
4.Wait until format ends and the phone restarts
I'm thinking that something with the sleep mode has gotten corrupted in memory. If this doesn't clear the problem, then you likely have a hardware/firmware fault and the phone should be taken in for repair or replacement.
/drt

Cannot establish wireless connection with WRT54G after power-off

My WRT54G (firmware v7.00.0) is connected to cable TV modem and
usually the wireless connection works fine, but after swiching off and later
on the power to WRT54G a laptop cannot establish WiFi connection to internet.
I can see in Odyssey software (for wireless communication) that my laptop
found the right network (SSID) but in status it says 'waiting for keys'.
I use WPA2 (TKIP). The laptop does not connect to internet.
When I connect it by cable (ethernet) the internet works fine, I have noticed
that by accessing the web-page utility of the router and simply clicking
save changes on wireless-settings page (without making any changes in
the settings) my laptop instantly establishes wireles connection and
everything works fine till next power swich-off.

Thanks for reply! I have my network in preffered, and the software/laptop locks on
the network (see it, says it have excellent signal strenght) and gives note
'waiting for keys' (the WPA2 encription key is in the settings - both of router and laptop client - Odyssey).
I've got firmware ver.7 so it is probably the latest.

E1000 won't reboot after power off

I have an E1000 installed. When I'm away for a while, I turn the power off to my modem and router to reduce electicity use. When I turn the power back on after returning, the E1000 will not reboot automatically. It will only reboot after I physically remove the power adapter cord from the E1000 body and reinsert it. Why doesn't it reboot automatically?

While turning on the devices, turn on the modem first. Wait for 1 minute and then turn on the router.
The router should reboot automatically when you turn it ON. However your router is not doing it automatically.

Reconfig required after power off

A week ago I changed my previous router by a new WRT54G. Old problems are gone, but unfortunately I got a new problem:
Each time the router is restarted (power off), I'm no longer able to connectwireless (Authorization, using WPA2 personal).
It needs always a wired connection first, then connect to the router setup:
Wireless - Wireless Security - Save Settings (without change). It looks like some settings are not saved correctly!!
Any help is highly appreciated.

Return the router. The new WRT54G hardware versions (v5, v6, v7, v8) are known for their various issues they have. Replace it with a WRT54GL which is the old hardware platform they have used for the first versions which work far more reliable.

Satellite P300 156 PSPC4E - White Media LEDs stay on after power-off

HI
I have a Toshiba Notebook Satellite P Series P300 156 (PSPC4E) which has just developed a problem
When I power off, the laptop shuts down normally and power button itself goes off, but the 6 white media LED's to the right of the power button remain on constantly. The only way to get these to turn themselves off is to disconnect the battery.
Can anyone please advise
Many thanks

Thanks for the replies
I tried altering the BOIS, but that only affects the illuminated strip along the top of the mouse touch pad.
I cant remember which version of BIOS that I got (I'm at work at the moment) but I tried downloading the latest from here (dated 18/03/10), and it made no difference.
Its a strange one. The lights stay on even if the laptop is closed for long periods. They just never go off, unless I take the battery out.
Message was edited by: hawkerpaul

Nexus 7010 Loses Config after power off

Similar Messages

Maybe you are looking for