Nexus 9 tablet looses microphone during call

Hi Just got this new nexus 9 tablet and during Skype calls, a few minutes in, my callers suddenly can't hear me. It's as if the microphone stops working. Everything else in the call is OK. If I hang up and redial its okay again for a few minutes. Any suggestions? George

I have been using Skype on my nexus 7 ever since it came out and have never had any problems. Sad to say this is not the case with nexus 9. Skype is my lifeline with all my family in Australia. I tried connecting and it was OK for about 30mins then off went the sound, redialled got only a few minutes, had to revert to using phone.
Found the following nexus forum site - product forum.google.com
There is a forum under "google hangouts" reporting on Skype sound problems.Please read it.
I am a silver surfer not a new age techy and only use Skype, if another integral programme works with safe mode then the problem must be with the third party product not syncing with the new nexus 9 lollipop system.

Similar Messages

IPhone 5s - Microphone During Calls

I received my new iPhone 5s today and have encountered an issue. When in the phone app, no one is able to hear me during calls. If I switch to speaker mode however, my voice will be picked up. I've also tested with Siri, and my voice is being picked up there without issue. There was also no issue with my voice being detected in Facetime. As far as I can tell this issue only exists during phone calls without the speaker on.
- I've upgraded to the latest version of iOS hoping that might resolve it, but no luck.
- Also, I've tried turning off the noise cancelation feature, but again with no luck.
Has anyone encountered this issue before? What steps would you recommend for resolving this?
Thanks!

Hey MKick,
I have found something that may help you fix this problem:
http://forums.macrumors.com/showthread.php?t=1483567
Hope it helps

Iphone 4. Microphone fails during calls

Iphone 4. Microphone fails during calls

Yeah -- I'm getting this myself. Did you ever find a solution?
Here's some more information:
Microphone DOES NOT work when:
I make a call via carrier (typical method)
I receive a call via carrier (typical method)
Microphone SOMETIMES works when:
I make a call via carrier (typical method), and then cuts out a few minutes during the call
I receive a call via carrier (typical method), and then cuts out a few minutes during the call
Microphone DOES work when:
Using recording apps (voice memos)
Make calls via data apps like: Skype, MagicJack. I can use these apps to call/communicate with the person on the other end of the call without ANY issues. Microphone does not cut out at all. Works perfectly.
Tried To Solve Using The Following (To no avail):
Plug in / out headphones/mic. This is functioning properly. When I take out headphones/mic, and use the volume toggle, it does not show headphones as being plugged in. Looks typical, and I can hear sound coming out of the speakers.
Tried using the external "speaker" option during calls. This had no effect. The speaker icon highlights, and appears as normal, but they still cannot hear me talking into the mic.
Switching Carriers in Settings > Carriers. I tried hopping onto another carrier (by disabling Auto), then moving back to my own Carrier. Something to note... THe other carrier didn't allow me to fully connect to it. I was not able to make a call on another carrier (I suspect this is normal). I then re-enabled Auto. Nothing helps.
Reboot, Toggle Airplane-mode
Latest Update (5.0.1)
Sync with iTunes
Summary Of Problem:
This is seemingly an issue while making / receiving calls through the carrier., but I've seen this problem a lot in other forums. They've tried different SIM, and carriers, and nothing's helped. I'll try a new SIM card next, though I don't see it as being a coverage thing what-so-ever. My data works, and my mic WORKS --- just not during phone calls.

Microphone not working on my iphone 4s unless i'm on speaker or using headphones during calls both incoming and outgoing?

During calls incoming and outgoing I can hear the other person but they cannot hear me unless I am on speaker phone or am using headphones?

Basic troubleshooting steps clearly outlined in the User Guide are restart, resest, restore from backup, restore as new.
If you still have problems after going through ALL the recommended troubleshooting steps, then you likely have a hardware issue. You'll need to bring your phone into Apple for evaluation.

IPhone 5c IOS7.0.3, other people can no longer hear me during calls unless I tap into speaker mode and back?

Hi,
I'm currently using an iPhone 4S, but my partner has just bought an iPhone 5c. A while ago, before the IOS7 upgrade, my phone would for some reason act as if I had clicked mute during calls. Nobody would hear me, but I could hear them perfectly. The only fixes were to hang up and recall them back, or to switch it to speaker mode and back again. Very annoying. However, after updating my IOS, it suddenly stopped doing this. It was fixed, I was happy, game on.
But recently, my partners phone which was working perfectly fine before the new IOS7.0.3 update, has developed this problem. Exact same issue, exact same solution. I wouldn't mind so much, but shes bought this phone in the last month, its a brand new phone, new software, new model... It shouldn't still be doing this! Whats worse is that when driving, its very dangerous for her to have to keep switching between speaker and not just to get her phone working. (She drivers with the phone in a cradle with hands free on).
This issue is... Annoying. I've found that its not exactly a rare thing, and that a lot of people have had it for quite a while, but the only solution I've seen is to open the back of your phone and cover a certain part with paper/cardboard... Not exactly what we want to do is it.
Does anybody have any advice or a solution to this, as I'm going a little crazy trying to reset everything and fix it!
Thanks in advance!

Same issues here. Sometimes during outgoing calls, people cannot hear me at all, even when the signal strength is good. Only solution is to soft reset the phone. A couple of times the person could hear me for the first few seconds of the call then it dropped completely.
I also experience the issue with the 3G data as you described (I think they are related... i.e., when the 3G data isn't working, the issues with outgoing calls exists too). The phone will just randomly seem to lose it's internet connection, even with full signal strength. Soft reset/toggling airplane mode fixes this.
I called Apple support; they asked if I was covering the microphone during outgoing calls (as if I'm that stupid). Come on Apple, I have a University degree in Computer Engineering, don't insult my intelligence! They then asked me to restore the phone (which I already did). Next solution they offered me was to replace the phone by sending me a new one first (at a cost of $35), or I could send it back and be phoneless for a week while they send a new one (which is not an option for me). I also put on a $30 Invisibile Sheild so if I exchange it, I already lose that. I believe the issue is not with the hardware, since the microphone seems to work just fine. Given that it is intermittent like this, it seems there's a software/firmware error somewhere that gets the phone into a bad state.
Very disappointed that the $800 phone I just bought functions worse for phone calls than the Nokia brick I had 8 years ago.
If anyone has a permanent solution for this that doesn't involve exchanging the phone, please let me know.

Issue with Proximity Sensor during calls - Continued v2

This thread is a continuation of Issue with Proximity Sensor during calls - Continued. which was getting too long and causing some browsers to time out. That thread has been locked and the last post links to this thread.
See also the initial thread Issue with Proximity Sensor during calls
Thank you.
Apple Discussions Hosts

rbrylawski wrote:
Goflying wrote:
mbassoc2003 wrote:
I wish that were so. Then they would probably be taking prompter action. But the return rate three weeks in was substantially lower than most handsets at launch and only a quarter that of the 3GS. I suspect the return rate has remained incredibly low and the figures are further slewed down the way by the worldwide distribution that is now in the tens of millions.
At 5% return rate on a product I understand that becomes a 'significant event' that becomes declarable to shareholders, so we know they haven't reached that milestone yet.
a disclosable event is not triggered by a specific stock return level unless apple has entered into covenants re same. Suggest you take a look at sec rules for more info
Still, unless you have insider knowledge, you don't know Apple's buying them back at record numbers. You may be guessing, but you likely don't have proof....
agree. I don't have any proof whatsoever, just a strong gut feeling that all is very much not as rosy in cupertino as it might seem.
For a company whose culture is steeped in phreakery, apple is showing an amazing inability to exert control.
too many screw ups, too many loose ends, too many whacky hires, too many media backlashes - maybe the senior staff went into dumb-mode while steve was away for so long
null

No sounds during call

hello i have iphone 4s wth 8.1.1 and its working fine but problem is neither i hear someone nor someone hear me during calls wat can i do plzzzz help

The resource below will provide some steps to address the issue you are having hearing conversations on the iPhone 4s:
If your voice is too faint or sounds unclear using iPhone, or iPod touch - Apple Support
http://support.apple.com/en-us/HT203792
Test the microphone
To find out if there is an issue with the microphone itself—and not the app you're using or your cellular connection—test the microphone with the built-in Voice Memos app. Speak into the microphone and then play back the recording. You should be able to hear your voice clearly.
Fix common issues
Follow these steps, testing after each with Voice Memos.
Unplug anything plugged into the headset jack.
If you're on a call and holding your phone next to your ear, speak into the microphone and make sure you don't block it with your fingers or shoulder.
If you're using a screen protector or case that covers the microphone, remove it. Clear any debris from the microphones.
Restart your device.
Update to the latest version of iOS.
If you've tried these steps and people still can't hear you well on calls, contact Apple Support.
If you can't hear a person on a call or voicemail or if the sound quality is poor on iPhone - Apple Support
http://support.apple.com/en-us/HT203800
While you're on a call, make sure that you can see the volume indicator on the screen when you press the volume buttons:
Check the connections
If your iPhone is connected to a headset, you won't be able to hear through the iPhone receiver or using speakerphone. Follow these steps, testing after each.
Make sure that you don't have anything plugged in to the headphone jack or the dock connector.
Go to Settings > Bluetooth and turn off Bluetooth.
Clear the receiver
The iPhone receiver won't work properly if it's blocked or dirty. Here's where the receiver is:
Follow these steps, testing after each:
Make sure nothing is blocking the receiver, such as a case or film.
If you have a new iPhone, remove the plastic film on the front and back of the device.
Check the receiver opening to see if it's blocked or dirty. If necessary, clean the receiver opening with a clean, small, dry, soft-bristled brush.
While you're on a call, turn on speakerphone. If you still can't hear, then your network or reception could be the issue. Try calling again later or from a different location.
Restart and update
Restart your iPhone and test again.
If there's still no sound or poor sound quality, update to the latest version of iOS.
I hope this information helps ....
- Judy

Crackle, pop, static disturbance during call.

Hello,
As many others have reported, during calls only, there is a constant static disturbance that makes conversation so uncomfortable.
Disabled noise supression and slow talk, no change.
Not changed sim card yet, will do this soon and report if there has been a difference.
Will also attempt to use the pc companion repair tool.
Please share any fixes or work arounds that you may know of.
This is a major inconvenience, im not sure i would buy a sony phone again.

If disabling microphone noise suppression did not change anything,try to boot in safe mode,see if the same occurs:
http://talk.sonymobile.com/t5/FAQ/How-to-boot-your-phone-into-safe-mode/m-p/348008
All we have to decide is what to do with the time that is given to us - J.R.R. Tolkien

Nokia N70 Buzzing fault during calls

Purchased N70 yesterday and noticed during calls there was a buzzing sound. Will be returning for a replacement. Has anyone else had this problem? Only happens when the backlight is on. Any ideas how to fix this

I think this has been mentioned here before... as you're both within the return period - get them back and see if a replacement model will sort the problem.
If you were outside the return period, I would suggest taking it to a Nokia Service Centres as I don't think there was a solution mentioned.
I've noticed some interference when I'm on the o2 3G band with a poor signal - Is this when you're on dual mode? Maybe you could try switching it to GSM and see if you're still affected? Not that it's a great solution - but could provide better feedback to the suppliers.
Nokia History: 3110, 5110, 7110, 7110, 3510i, 6210, 6310i, 5210, 6100, 6610, 7250, 7250i, 6650, 6230, 6230i, 6260, N70, N70, 5300, N95, N95, E71, E72
Android History: HTC Desire, SE Xperia Arc, HTC Sensation, Sensation XE, One X+, Google Nexus 5

6 plus turns off during calls

i am on my second 6plus and having the same issue. My issue is that the phone shuts off 20% of the time during calls. The phone will be dark for 20 seconds and then the apple logo appears to start back up, like it is rebooting. After the logo reappears the phone home screen comes back up and the caller is still there. So I don't ever loose the call, I just loose the ability to hear or saying anything. Plus the phone is dark like it is completely turned off. I know another phone will not fix this, anyone know the software issue? sprint is the carrier

Hello Mwcourter,
Having your device replaced multiple times can certainly be frustrating. After reviewing your post, it sounds as though your device is resetting during use. I have located an article that can help with software issues. Have you attempted to restore the device to factory settings without restoring from a backup? Test the issue on a new installation, and make sure that it works. Then use the same article to restore from your backup to either verify it still works, or isolate the issue to the backup itself.
How to erase your iOS device and then set it up as a new device or restore it from backups
Thank you for contributing to Apple Support Communities.
Cheers,
BobbyD

IPhone 4s earpiece very quiet during calls, but normal in Voice Memos.

My iPhones earpiece is really quiet during calls, but I'm loud and clear on the other end. It's also weird because if I record a message in Voice Memos, and I play it through the earpiece, it sounds fine. I'm in 5.1.1, Jailbroken (shouldn't make a difference) and I even poked a hole in the little earpiece grill, which didn't help and didn't hurt. And yes, the plastic piece is gone, I've had this phone for close to 5 months.

Mine also has this issue. Its the 64GB version. It's happened twice now. After about 5 mintues the call quality degragates and it sounds like i'm in a wind tunnel. The person on the other end also hears this and it is no longer possible to hear each other. Both times i've been using the new headphones provided with the 4s. I've done lots of searching on this issue and only found your thread which leads me to believe its not a common problem. I'm just not sure whether its a firmware or hardware issue but as nobody else has this issue its more than likely a hardware issue! :-(

IPhone 4 Mic & Speaker not Working during Call

Hello All,
I have iphone 4 and it was locked on at&t and was running ios 5.0.1, now i have unlocked my iphone and now i am using ios 5.1.1. But i have a problem, when i call someone i cant hear anything "no dial tone sound and no sound during call" & speaker mode is also not working and nor the person cant hear my voice. I also tested on my another phone but same problem.....
So can you tell me is this a hardware problem or software problem ?? and yeah i can record voice memos and i can listen my memos with speaker on and off
Waiting for reply....

Do the basic troubleshooting steps described in the User Guide:
1. Reset iPhone (no data loss): Press both home and power buttons for at least 10 seconds, releasing when the Apple logo appears.
2. Restore in iTunes using a backup
3. Restore in iTunes as new, without using a backup.
If restoring as new doesn't help, there is a hardware failure.

Low quality sound during call

Hello,
Since the iOS 7 update that I've been noticed that the sound quality during calls is very poor to others, almost like I speaking away from the iphone without speaker, regardeless I keep earing everything loud and clear!
I've already tested with other iphone 4/4S/5 iOS 7 users, and also running different iOS versions, as well as other phone brands, and the problem maintains!
Upgraded to 7.0.3 today, despite the improvement/enhancements/bug corrections list dont mention any issue addressed to this problem, hoping to solve the problem, but nothing change, its pretty much the same as before!
All settings are at the max, and also perform some tasks as suggested on apple support forums like tweaking the accessability options, by turning noise reduction off, but still the same!!
My S/N is C34JPLSTDTWF.
Hope I had described accuarately, in order to you perform the correct troubleshoot for this, this if you ain't already done it!
Best regards,
Pedro Sousa

This happened to me as well and I confirmed others are experiencing same speaker/mic/bluetooth issues with both 4S and iPad 2, 3. Applied the updated patch yesterday, things are worse because now I have NO sound via the speaker. What's the FIX?!

System failure, during call of function module RSWR_RFC_SERVICE_TEST

Hi Team,
     I am working with BW and Portal Integration, with the Netweaver
2004s SP 11 version. I have a issue when i run the RSPOR_SETUP program
to test the configuration.
The error is on status 5 and 12, i get the following error:
System failure, during call of function module RSWR_RFC_SERVICE_TEST,
and when i enter at the dev_jrfc.trc log file, i have the following
error:
Exception thrown [Tue Jul 10 16:12:16,687]:Exception thrown by
application running in JCo Server
java.lang.RuntimeException: call FM RSWR_RFC_SERVICE_TEST to ProgId
smxpedvc_PORTAL_EPD on host smxpedvc.grupoempresarialangeles.com.mx
with SSO not authorized: No login module succeeded.
        at
com.sap.engine.services.rfcengine.RFCDefaultRequestHandler.handleRequest
(RFCDefaultRequestHandler.java:79)
        at com.sap.engine.services.rfcengine.RFCJCOServer.handleRequest
(RFCJCOServer.java:156)
        at com.sap.mw.jco.JCO$Server.dispatchRequest(JCO.java:7785)
        at com.sap.mw.jco.MiddlewareJRfc$Server.dispatchRequest
(MiddlewareJRfc.java:2405)
        at com.sap.mw.jco.MiddlewareJRfc$Server.listen
(MiddlewareJRfc.java:1728)
        at com.sap.mw.jco.JCO$Server.listen(JCO.java:8145)
        at com.sap.mw.jco.JCO$Server.work(JCO.java:8265)
        at com.sap.mw.jco.JCO$Server.loop(JCO.java:8212)
        at com.sap.mw.jco.JCO$Server.run(JCO.java:8128)
        at com.sap.engine.core.thread.impl3.ActionObject.run
(ActionObject.java:37)
        at java.security.AccessController.doPrivileged(Native Method)
        at com.sap.engine.core.thread.impl3.SingleThread.execute
(SingleThread.java:100)
        at com.sap.engine.core.thread.impl3.SingleThread.run
(SingleThread.java:170)
Could you help me to solve this issue.
Thanks so much.

Have you checked the user that is used to connect from J2EE back to ABAP?
I had a similar problem, went into the Visual Administrator and found the incorrect password (or possibly outdated password) was being used to communicate back to ABAP, and updating that sorted out my problem.
Hope this helps.
Cheers,
Andrew

Errors occurred during call of function module BUPR_EMPLO_DELETE

when distributing employee data from (HCM) to (CRM) there is an error that appears in relation with the settings for the Business Parner:
"Errors occurred during call of function module BUPR_EMPLO_DELETE
Message no. R11335
Diagnosis
The business partner BAPIs were called up incorrectly. The indicator IV_X_SAVE was given differing settings when the modules were called.
Within a LUW, the indicator must be consistently set or not set.
System Response
The indicator IV_X_SAVE should be set or not set once off. Up to COMMIT WORK the content of the field may not be changed, as problems will otherwise occur with the internal memory, thus leading to runtime errors."
This prevents CRM to be updated with the changes. Kindly help me on the same.

Hi Sai,
This is too late to reply this post, but to let everyone know about the issue I am posting here.
Start new UI session and put breakpoint at BUPR_EMPLO_DELETE and check parameter IV_X_SAVE everytime, till you get the error message. The parameter IV_X_SAVE should be same/consistent (either ' ' or 'X') in whole Logical Unit of Work. It should not change in between.
I faced the same kind of problem and found that standard was passing IV_X_SAVE = ' ' and in our custom code we were passing IV_X_SAVE = 'X'. I changed it to IV_X_SAVE = ' ' and my problem got resolved.
You can try the same. Please post the alternate solution if you find it.
Best Regards,
Rahul Koshti

Nexus 9 tablet looses microphone during call

Similar Messages

Maybe you are looking for