Nexus 9500 : DAI is not supported
Hello
I have DCI network which has double-side vPC configured
so I want filtering for HSRP localization between DCI such as followed configuration
ip access-list HSRP_IP_filter
10 deny udp any 224.0.0.2/32 eq 1985
20 deny udp any 224.0.0.102/32 eq 1985
30 permit ip any any
mac access-list HSRP_MAC_filter
10 deny 0000.0c07.ac00 0000.0000.00ff any
20 deny 0000.0c9f.f000 0000.0000.0fff any
30 permit any any
interface Po4
ip port access-group HSRP_IP_filter in
mac port access-group HSRP_MAC_filter
but DAI is supported in this NX-OS 6.1(2)I3(1)
Do I need to apply DAI ? or if DAI needs, Do you have alternative way instead of DAI?
Seems to be an error on the Nexus 3k product page. We had a customer who purchased these for VPC support.
http://www.cisco.com/en/US/products/ps11541/index.html
Nexus 3500 Features
Ultra-Low Latency
Line-rate layer 2 and 3 switching at ultra-low latencies
Ideal for high-performance trading workloads
Mission-Critical Features
Network Address Translation (NAT)
Virtual Port Channel
IEEE-1588 PTP
Similar Messages
-
Cisco Nexus and 10GbE Autonegotiation not supported?
Hi,
I'm currently reading through the Interfaces Config Guide for Nexus 5600 NX-OS 7.x and have found the following statement:
Autonegotiation configuration is not applicable on 10-Gigabit Ethernet ports. When autonegotiation is
configured on a 10-Gigabit port the following error message is displayed:
ERROR: Ethernet1/40: Configuration does not match the port capability
Is it true that autonegotiation is not supported for 10GbE Interfaces on Cisco Nexus? I thought autonegotation was supported by 10GbE?! So would it be best practice so set a fixed speed on all Interfaces (servers, other switches) connected to the 10GbE ports on the Nexus switches?
Thanks,
MichaelHi Bilal,
thanks. Yes, I know that 10GbE can run over both media types, the problem here is that the documentation starts with stating that auto negotiation is not supported for 10GbE in beneral but later references only 10-GBASE-T, so I was not sure what is true - whether auto-negotiation only not works with copper or with all ports.
But I guess then it is true for all 10GbE ports, no matter what media-type. It's somewhat stange however, since I have read that auto-negotiation is generally supported for 10GbE (according to Wikipedia, at least). Maybe only Cisco doesn't supported auto-negotiation for 10GbE.
Thank you again,
Michael -
9500 Communicator lack of support - USA
I purchased the 9500 Communicator from Dubai back in Nov 2004 while stationed overseas with the US military, when the 9500 first came out. I have been using the phone in the US without any real major issues. Being the clumsy person that I am, I have dropped the phone on several occasions. On one of those occasions the phone fell and the front face came off and so did the keypad. It was windy and the keypad flew away why it was not attached as one with the face place I have no clue, what was Nokia thinking? Still I was able to use the phone since I remembered where the numbers were on the blank keypad.
My issue with Nokia is:
I have been trying for over two weeks to get some one in Nokia (USA, Middle East and UK) to give me a Repair Service Center's address where I can mail my communicator. I need to replace the worn/scratched/broke front and back cover as well as getting the firmware upgrade [current version I have is: 4.44(1) ] and yes, my front cover has started to flop as well.
1) I do NOT care WHERE I have to send it, just give me an address!
2) Yes I know that it is out of warranty and that I WILL have to pay for the service and parts, FINE I will PAY, JUST GIVE ME A PLACE TO MAIL IT TO! This is the question I have been asking for ever it seems! What part of this request is not comprehend able?
3) Nokia’s customer support is so pathetic! All you get is the run around! Everyone is just trying to point the finger to someone else. I even tried to order just the keypad from the US and I was told there might be a difference between the US keypad and the UK version - I DO NOT THINK SO! I have been in the telecom & computer industry in both commercial & government/military for almost 15 years. It's not like the US/UK keypad is in any other language than English! The number 1 will always look like the number 1 in the UK and the US! What a lame excuse! It is like Nokia can not communicate with each other at a Global Enterprise level! Is this NOT a Global company? What type of message are you sending your customers and your investors? I mean just because there are regional subsidiaries should not mean that there is NO communications between other regions, or wait are Nokia's products NOT communications equipment? If they can sell communication equipment and can NOT communicate amongst themselves that's pretty pathetic! It is pretty sad that one customer service center has no access to the other. Have you not heard of the software like the Remedy ticketing system? It is great for supporting things like customer support even on a Global scale!
What should have been a mundane task of giving me an address has turned into a praying for a miracle to happen request! Why did this happen? Why should it go so far up to the next level? What type of changes in training is Nokia implementing if that?
Why doesn’t the Executive branch review the Operations & Maintenance (O&M) procedures to make Nokia more efficient? Do they not listen to what their customers and industry want/ need? There are so many websites that do reviews on products like Nokia phones, is there no group in Nokia that takes heed to what others think of their product and review them and if possible send those changes down to the research and development and production departments? I know I am not the smartest guy, but I think I have been around to know better on what things companies can do to create and sell their product and thus make a name and PROFIT for themselves! Currently in the US, Nokia's stock price is ONLY $4.00 (USD). I'll bet if they actually made better products, see where industry is headed, actually listened to their customers and did some really good predictive analyses in marketing they would be an even better company producing a much better product that would create a frenzy of people all over the world wanting to buy their products like the Motorola Razr mobile phone when it first came out!
It seems that everyone I have spoken to says the same thing: Nokia products are nice but they lacks features, standard operating system, availability of software, looks, and support!
Nokia is suppose to be a Global company trying to sell its products to people and companies on a Global scale. If you can NOT support your own product then how in the hell are you suppose to support your customers? I always thought that the 9500 Communicator was Nokia's top of the line product? Well if that being the case then Nokia SHOULD have top notch support for this product! If Nokia is suppose to be the Mercedes of mobile phones well act like it then! If you can not support your high end system then why produce it in the first place? There should be tons of competent technical support professionals, options, upgrades and accessories etc... if you want to make Nokia into an industry leader then you need to have a product that works well and is sought after not only by customers but also by your OWN employees and is supported well and get some real talented minds to think of some newer things to integrate in your phone lines. Basically the Communicator series should have EVERYTHING that the mobile business customer needs on the road without having to carry around a laptop!
Maybe on the NEXT version/ generation of Communicators they would have:
Vibrate mode
Voice recognition
Operating system should be Microsoft windows mobile based
More local storage especially for MP3s
Use ring tones
2.0 or greater Mega pixel camera
Mini USB connector
USB 2.0
Programmable soft keys
Newer Bluetooth for stereo headsets
A lit keypad for when the cover is open
An external keyboard that folds and you can use for emails/ SMS
802.11 (b/g/n) support with WAP/ WEP encryption
Colored face and back plates that are interchangeable
Touch screen would be an improvement
Larger capacity internal memory
Ability to block calls that were Unknown, or originate from blocked numbers, certain numbers/ certain area codes etc...Hi
http://www.apps.nokia.co.uk/clubnokiaservice/
If you key in 'London' into the search box, you should get a list of Nokia service companies who should be able to help.
Although I'm not in London I have used similar 3rd party companies to do chargable repairs (eg when hinges broke!)
You could try calling some of the them to see how they might be able to help.
Good luck!!
Rich -
Maven giving "annotations are not supported in -source 1.3" for @Entity
I m using maven for spring, hibernate with jpa . When i m running comman "mvn clean install" ,it is giving error in compilation of a bean class which is using jpa annotations.The error is :
annotations are not supported in -source 1.3
(use -source 5 or higher to enable annotations)
@Entity
Pom.xml is as below :
<project xmlns="http://maven.apache.org/POM/4.0.0" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="http://maven.apache.org/POM/4.0.0 http://maven.apache.org/maven-v4_0_0.xsd">
<modelVersion>4.0.0</modelVersion>
<groupId>com.niit.core</groupId>
<artifactId>Spring3Example</artifactId>
<packaging>jar</packaging>
<version>1.0-SNAPSHOT</version>
<name>Spring3Example</name>
<url>http://maven.apache.org</url>
<properties>
<org.springframework-version>3.1.2.RELEASE</org.springframework-version>
</properties>
<repositories>
<repository>
<id>JBoss Repo</id>
<url>https://repository.jboss.org/nexus/content/repositories/thirdparty-releases</url>
</repository>
</repositories>
<build>
<plugins>
<plugin>
<artifactId>maven-war-plugin</artifactId>
<version>2.0</version>
</plugin>
</plugins>
</build>
<dependencies>
<dependency>
<groupId>org.springframework</groupId>
<artifactId>spring-context</artifactId>
<version>${org.springframework-version}</version>
</dependency>
<!-- <dependency>
<groupId>hsqldb</groupId>
<artifactId>hsqldb</artifactId>
<version>1.8.0.2</version>
</dependency>
-->
<dependency>
<groupId>org.springframework</groupId>
<artifactId>spring-core</artifactId>
<version>${org.springframework-version}</version>
</dependency>
<dependency>
<groupId>junit</groupId>
<artifactId>junit</artifactId>
<version>3.8.1</version>
<scope>test</scope>
</dependency>
<dependency>
<groupId>javax</groupId>
<artifactId>javaee-api</artifactId>
<version>6.0</version>
<scope>provided</scope>
</dependency>
<dependency>
<groupId>org.hibernate</groupId>
<artifactId>hibernate-core</artifactId>
<version>3.6.10.Final</version>
</dependency>
<dependency>
<groupId>org.hibernate.java-persistence</groupId>
<artifactId>jpa-api</artifactId>
<version>2.0-cr-1</version>
</dependency>
<dependency>
<groupId>org.hibernate</groupId>
<artifactId>hibernate-entitymanager</artifactId>
<version>3.5.0-Beta-2</version>
</dependency>
<dependency>
<groupId>javax.servlet</groupId>
<artifactId>servlet-api</artifactId>
<version>2.5</version>
</dependency>
</dependencies>
</project>
And class is as below :
package com.niit.form;
import javax.persistence.Column;
import javax.persistence.Entity;
import javax.persistence.GeneratedValue;
import javax.persistence.Id;
import javax.persistence.Table;
@Entity
@Table(name="CONTACTS")
public class Contact {
@Id
@Column(name="ID")
@GeneratedValue
private Integer id;
@Column(name="FIRSTNAME")
private String firstname;
public String getFirstname() {
return firstname;
public void setFirstname(String firstname) {
this.firstname = firstname;
public void setLastname(String lastname) {
this.lastname = lastname;
public Integer getId() {
return id;
public void setId(Integer id) {
this.id = id;
}java version is 1.6.0_24
There is no settings.xml in users/.m2
I think , maven is using default settings.xml which is in M2_HOME\conf which has everything commented as below:
<?xml version="1.0" encoding="UTF-8"?>
<!--
Licensed to the Apache Software Foundation (ASF) under one
or more contributor license agreements. See the NOTICE file
distributed with this work for additional information
regarding copyright ownership. The ASF licenses this file
to you under the Apache License, Version 2.0 (the
"License"); you may not use this file except in compliance
with the License. You may obtain a copy of the License at
http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing,
software distributed under the License is distributed on an
"AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY
KIND, either express or implied. See the License for the
specific language governing permissions and limitations
under the License.
-->
<!--
| This is the configuration file for Maven. It can be specified at two levels:
|
| 1. User Level. This settings.xml file provides configuration for a single user,
| and is normally provided in $HOME/.m2/settings.xml.
|
| NOTE: This location can be overridden with the system property:
|
| -Dorg.apache.maven.user-settings=/path/to/user/settings.xml
|
| 2. Global Level. This settings.xml file provides configuration for all maven
| users on a machine (assuming they're all using the same maven
| installation). It's normally provided in
| ${maven.home}/conf/settings.xml.
|
| NOTE: This location can be overridden with the system property:
|
| -Dorg.apache.maven.global-settings=/path/to/global/settings.xml
|
| The sections in this sample file are intended to give you a running start at
| getting the most out of your Maven installation. Where appropriate, the default
| values (values used when the setting is not specified) are provided.
|
|-->
<settings xmlns="http://maven.apache.org/SETTINGS/1.0.0"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xsi:schemaLocation="http://maven.apache.org/SETTINGS/1.0.0 http://maven.apache.org/xsd/settings-1.0.0.xsd">
<!-- localRepository
| The path to the local repository maven will use to store artifacts.
|
| Default: ~/.m2/repository
<localRepository>/path/to/local/repo</localRepository>
-->
<!-- interactiveMode
| This will determine whether maven prompts you when it needs input. If set to false,
| maven will use a sensible default value, perhaps based on some other setting, for
| the parameter in question.
|
| Default: true
<interactiveMode>true</interactiveMode>
-->
<!-- offline
| Determines whether maven should attempt to connect to the network when executing a build.
| This will have an effect on artifact downloads, artifact deployment, and others.
|
| Default: false
<offline>false</offline>
-->
<!-- pluginGroups
| This is a list of additional group identifiers that will be searched when resolving plugins by their prefix, i.e.
| when invoking a command line like "mvn prefix:goal". Maven will automatically add the group identifiers
| "org.apache.maven.plugins" and "org.codehaus.mojo" if these are not already contained in the list.
|-->
<pluginGroups>
<!-- pluginGroup
| Specifies a further group identifier to use for plugin lookup.
<pluginGroup>com.your.plugins</pluginGroup>
-->
</pluginGroups>
<!-- proxies
| This is a list of proxies which can be used on this machine to connect to the network.
| Unless otherwise specified (by system property or command-line switch), the first proxy
| specification in this list marked as active will be used.
|-->
<proxies>
<!-- proxy
| Specification for one proxy, to be used in connecting to the network.
|
<proxy>
<id>optional</id>
<active>true</active>
<protocol>http</protocol>
<username>proxyuser</username>
<password>proxypass</password>
<host>proxy.host.net</host>
<port>80</port>
<nonProxyHosts>local.net|some.host.com</nonProxyHosts>
</proxy>
-->
</proxies>
<!-- servers
| This is a list of authentication profiles, keyed by the server-id used within the system.
| Authentication profiles can be used whenever maven must make a connection to a remote server.
|-->
<servers>
<!-- server
| Specifies the authentication information to use when connecting to a particular server, identified by
| a unique name within the system (referred to by the 'id' attribute below).
|
| NOTE: You should either specify username/password OR privateKey/passphrase, since these pairings are
| used together.
|
<server>
<id>deploymentRepo</id>
<username>repouser</username>
<password>repopwd</password>
</server>
-->
<!-- Another sample, using keys to authenticate.
<server>
<id>siteServer</id>
<privateKey>/path/to/private/key</privateKey>
<passphrase>optional; leave empty if not used.</passphrase>
</server>
-->
</servers>
<!-- mirrors
| This is a list of mirrors to be used in downloading artifacts from remote repositories.
|
| It works like this: a POM may declare a repository to use in resolving certain artifacts.
| However, this repository may have problems with heavy traffic at times, so people have mirrored
| it to several places.
|
| That repository definition will have a unique id, so we can create a mirror reference for that
| repository, to be used as an alternate download site. The mirror site will be the preferred
| server for that repository.
|-->
<mirrors>
<!-- mirror
| Specifies a repository mirror site to use instead of a given repository. The repository that
| this mirror serves has an ID that matches the mirrorOf element of this mirror. IDs are used
| for inheritance and direct lookup purposes, and must be unique across the set of mirrors.
|
<mirror>
<id>mirrorId</id>
<mirrorOf>repositoryId</mirrorOf>
<name>Human Readable Name for this Mirror.</name>
<url>http://my.repository.com/repo/path</url>
</mirror>
-->
</mirrors>
<!-- profiles
| This is a list of profiles which can be activated in a variety of ways, and which can modify
| the build process. Profiles provided in the settings.xml are intended to provide local machine-
| specific paths and repository locations which allow the build to work in the local environment.
|
| For example, if you have an integration testing plugin - like cactus - that needs to know where
| your Tomcat instance is installed, you can provide a variable here such that the variable is
| dereferenced during the build process to configure the cactus plugin.
|
| As noted above, profiles can be activated in a variety of ways. One way - the activeProfiles
| section of this document (settings.xml) - will be discussed later. Another way essentially
| relies on the detection of a system property, either matching a particular value for the property,
| or merely testing its existence. Profiles can also be activated by JDK version prefix, where a
| value of '1.4' might activate a profile when the build is executed on a JDK version of '1.4.2_07'.
| Finally, the list of active profiles can be specified directly from the command line.
|
| NOTE: For profiles defined in the settings.xml, you are restricted to specifying only artifact
| repositories, plugin repositories, and free-form properties to be used as configuration
| variables for plugins in the POM.
|
|-->
<profiles>
<!-- profile
| Specifies a set of introductions to the build process, to be activated using one or more of the
| mechanisms described above. For inheritance purposes, and to activate profiles via <activatedProfiles/>
| or the command line, profiles have to have an ID that is unique.
|
| An encouraged best practice for profile identification is to use a consistent naming convention
| for profiles, such as 'env-dev', 'env-test', 'env-production', 'user-jdcasey', 'user-brett', etc.
| This will make it more intuitive to understand what the set of introduced profiles is attempting
| to accomplish, particularly when you only have a list of profile id's for debug.
|
| This profile example uses the JDK version to trigger activation, and provides a JDK-specific repo.
<profile>
<id>jdk-1.4</id>
<activation>
<jdk>1.4</jdk>
</activation>
<repositories>
<repository>
<id>jdk14</id>
<name>Repository for JDK 1.4 builds</name>
<url>http://www.myhost.com/maven/jdk14</url>
<layout>default</layout>
<snapshotPolicy>always</snapshotPolicy>
</repository>
</repositories>
</profile>
-->
<!--
| Here is another profile, activated by the system property 'target-env' with a value of 'dev',
| which provides a specific path to the Tomcat instance. To use this, your plugin configuration
| might hypothetically look like:
|
| ...
| <plugin>
| <groupId>org.myco.myplugins</groupId>
| <artifactId>myplugin</artifactId>
|
| <configuration>
| <tomcatLocation>${tomcatPath}</tomcatLocation>
| </configuration>
| </plugin>
| ...
|
| NOTE: If you just wanted to inject this configuration whenever someone set 'target-env' to
| anything, you could just leave off the <value/> inside the activation-property.
|
<profile>
<id>env-dev</id>
<activation>
<property>
<name>target-env</name>
<value>dev</value>
</property>
</activation>
<properties>
<tomcatPath>/path/to/tomcat/instance</tomcatPath>
</properties>
</profile>
-->
</profiles>
<!-- activeProfiles
| List of profiles that are active for all builds.
|
<activeProfiles>
<activeProfile>alwaysActiveProfile</activeProfile>
<activeProfile>anotherAlwaysActiveProfile</activeProfile>
</activeProfiles>
-->
</settings> -
E63 file format not supported error message.
I have recently purchased a E63 in India.
My earlier model was 9500 Communicator. I have transferred all the data from 9500 to E63 and all files etc. are opening properly, except files in the folder 'My Documents' which are 'Word' or 'Excel' files.
Whenever I try to open the file it says "File Format Not Supported".
Kindly help.Is QuickOffice installed and activated?
‡Thank you for hitting the Blue/Green Star button‡
N8-00 RM 596 V:111.030.0609; E71-1(05) RM 346 V: 500.21.009 -
How to reboot Nexi using SNMP (tsMsgSend not supported)
How does one reboot Nexus using SNMP?'
Normally, I reboot IOS gear using:
snmpset -c {private} {switch|router|whatever} tsMsgSend.0 i 2
tsMsgSend OBJECT-TYPE
SYNTAX INTEGER {
nothing(1),
reload(2),
messagedone(3),
abort(4)
ACCESS read-write
STATUS mandatory
DESCRIPTION
"Sends the message. The value determines what
to do after the message has completed."
::= { lts 9 }
But our new Nexi (5000 and 7500) don't support tsMsgSend in various ways:
N5K
Reason: notWritable (That object does not support modification)
Failed object: OLD-CISCO-TS-MIB::tsMsgSend.0
N7K
Reason: wrongValue (The set value is illegal or unsupported in some way)
Failed object: OLD-CISCO-TS-MIB::tsMsgSend.0
Yes, I have the following in the Nexi config files:
snmp-server system-shutdown
How does one reboot a Nexus using SNMP?
--sk
Stuart Kendrick
FHCRCHi,
The only way that a device can be reloaded using SNMP is with the SNMP object tsMsgSend
(1.3.6.1.4.1.9.2.9.9).
As per the official Nexus MIB support list, the OID is not supported in NX-OS
Thanks-
Afroz
[Do rate the useful posts] -
Power Mac 7200/120 won't boot off new hard drive. Says HD "not supported"
I just recently came into possession of a PowerMac 7200/120. The only thing it came with is a boot cd with Mac OS 8.1. It booted fine off the cd with only the date/time issues of a dead PRAM battery, but when I tried to boot the internal HD on its own, it was a no-go. Flashing ?. When I tried to verify the HD, the software would not even find the HD. Not even listed on the program. You can't initialize what isn't there, so I ordered a new HD from an online vendor. I replaced it according to the directions on the Apple .pdf file I googled. I also reset the logic board and replaced the PRAM battery. Upon booting after all this ... still flashing ?. I run the same verification process as before and I actually DO see this HD listed, but it says it is "not supported" and doesn't allow me to initialize it. It's virtually the same quantum fireball HD with the Apple logo as the old one I just took out, just a different GB size. Connections and slots are all the same. Is this just not the right HD for my computer? Is there something I need to download? I just rebuilt a Performa 6300cd with ZERO issues.
Ok ... a couple of mistakes on my part which of course could change EVERYTHING. I'm embarassed with the amount of mistakes in my own question. A couple of forgetful omissions on my part ...
#1. The drive DID start up just fine upon first switching out the HD. Original software on HD was 8.1, but as I needed to run older programs not compatible with 8.1, I initialized and installed 7.5.3 clean. (I know ... HUGE omission here, but be kind as I've been working on multiple computers and it has been a couple months since I did this). It worked fine after download. After coming back to this computer a couple of months later, I get the flashing ? again (like before the HD switch).
#2.The HD the online vendor sent me was not the one I ordered, but ended up being a carbon copy of the one I took out except the GB size (which was actually larger than the one I ordered). Didn't physically count the pins, but it plugged in fine. Everything fit.
#3. I also forgot to mention that while the CD drive worked, the floppy either spat my disks out at me or asked to initialize them. These were the same floppies that I took out of my Performa literally a minute earlier (which worked).
#4. The 8.1 cd is a mistake on my part again. Turns out it's the black-faced 7.5.3 cd (7200, 7500, 7600, 8500, and 9500 series). Got confused with the 8.1 drive.
UPDATE
The strangest thing ... I just booted up off the cd and it's now reading the HD. I ejected the cd and booted it up on its own ... and it works just fine. I did NOTHING since I asked the question. In fact, I just booted the computer back up in response to your response.
Before I delved into these boards and bothered to ask for help ... I had opened it up, cleared out a TON of dust bunnies with my can o' air, pressed the CUDA? chip, and then replaced the PRAM battery. Restarted holding down cmd-opt-p-r until it chimed again and it was still a flashing ?. You could hear it clicking as if trying to start the drive up at regular intervals. I restarted the computer well over 10 times hoping it was just something jammed up in the HD (though just bought) and it was the same flashing ?. And now today ... did nothing and it boots up just fine. I check the drive setup lite and it now shows macintoshHD there (instead of unsupported drive - original showed nothing at all).
Does it take time for the PRAM battery or logic board to reset? Did it just needed a thorough internal cleaning? Or should I chalk this up as just being a really old comp?
I really don't want to go delving back into it now that it's working to check the SCSI terminations, jumpers, etc. I'm going to assume those are ok now it's booting. -
Cisco DCNM 6.2 does not support most of the switches in my network
Hi All,
I have just installed Cisco DCNM 6.2. I have run a discovery using SNMP v1 my core switch which is a 3750G stack. DCNM discovers all my switches but does not support the 2960 and 3750 switches. The only switches I can select to manage and are supported are a 4510 and 3550. I have also run another discovery using SNMPv3 on a different core switch (Nexus 3K) at one of our remote sites. DCNM found all the other 2960s in that network but I can only select the two Nexus switches in the core to manage. What do I need to do to be able to manage all my switches switch?
Thank you in advance.Hello,
DCNM is meant for data centre network management and as such only supports the MDS, Nexus and the 6500 series switches, see the RN under supported Cisco platforms and software:
http://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/6_x/dcnm/release/notes/dcnm_6_2_5a_relnotes.html#pgfId-314209
For the discovery issue DCNM should 'see' the other devices so you need to have a look at your SNMP and CDP (used for neighbour discovery on a per hop basis) settings on each of the devices.
For an software package to manage LAN/WAN environments you really need to be looking at Cisco Prime LMS.
We are going through the same problem, it would be nice to be able to manage the DC and LAN from DCNM.
Regards
Daniel Hunter -
HT203433 I purchase a game not support by my device
I purchase a game not support by my device
http://www.howtogeek.com/120277/how-to-install-flash-on-the-nexus-7-and-other-jelly-bean-devices/
You do not need a Beta channel build of Firefox (which currently is 32.0b6) to use Flash as the issue was you needed Firefox 27.0 or newer to use the old Flash 11.1 plugin on Android '''4.4'''. after it came out on tablets/phones.
What Nexus 7 version do you have as there was a 2012 and a 2013 model. A easy way to tell if it is a 2013 is it has a camera on each '''back''' and front while 2012 only has one on front.
If it is the 2012 then it has a Nvidia Tegra 3 so the old Flash 11.1 Plugin is disabled.
For reading only as Bugzilla is not a discussion forum or for "me too" comments.
*[https://bugzilla.mozilla.org/show_bug.cgi?id=968219 Bug 968219 - flash does not work on Nexus 7]
*[https://bugzilla.mozilla.org/show_bug.cgi?id=957694 Bug 957694 - Hang/deadlock with Flash on 4.4 on Tegra3] -
Upload Error message: HTTPS protocol is not supported
Hi,
Whenever I do a quick par upload i'm getting an 'Operation failed' message to check sap-plugin.log.
Log says
Upload Error message: HTTPS protocol is not supported, please ensure this server is not using HTTPS. My webdynpro applications are getting deployed without any issues.
How to resolve this?
Thanks
SumathiHi Sumathi,
As there are often problems with the Quick PAR Upload reported, I would suggest to use the "normal" PAR upload from the icon tray (you have to activate the portal icons in the icon tray). That is almost that "quick" (one or two clicks more needed, we don't talk about more than a second) and - it works (it least it should, and at least it works in most cases even if the Quick PAR Upload fails).
Hope it helps
Detlev -
MacBook Mini-DVI to VGA - Samsung 32" LCD - Mode Not Supported
I followed the instructions on Apple's site to use the MacBook with the lid closed and an external LCD. It worked perfectly the first time I tried it. (I believe in 1920 x 1024). It seemed a little hard to read so I changed the Display resolution, then encountered the "Mode Not Supported" on my LCD. I unhooked and used my MacBook to change the settings back, but the MacBook seems to revert to the "Mode Not Supported" resolution when I close the lid. Any suggestions? Can I reset the Display Preferences on my MacBook?
I think this procedure should work, but it requires an external USB keyboard.
- Shut down the Mac.
- Have all the following connected:
- MacBook power supply
- External display
- USB keyboard and mouse
- Open the lid on the MacBook and hit the power button.
- Immediately close the lid on the MacBook and start holding down the Shift key on the USB keyboard.
- Release the Shift key once you see the spinning gear on the gray screen on the external display.
The above procedure should cause the Mac to start in Safe mode and hopefully will finish booting into a useable screen. If that is the case, go into Displays preferences and select a known working resolution different from the one the Mac started up in under Safe mode. Now restart normally. Hopefully the newly selected resolution will persist through the normal restart and you will have a working external screen again. -
I have a late 2009 MacBook which I want to connect to an old LG tv. The tv does not support HDMI it only has the (red, while, and yellow) ports. Sorry I dunno the exact name for it.
So I was thinking of using the Apple Mini DVI to Video Adapter (s-video), link below...
http://store.apple.com/Catalog/dk/Images/M9319_screen.jpg
But I'm afraid that the MacBook might not support the adapter.
Can anyone give me a solution for this? Is there an alternative way of doing this? I'm kinda new to apple display adapters.The Late 2009 model 6,1 has a Mini DisplayPort not the Mini-DVI. To see which model you have go to the Apple in the upper left corner and select About This Mac, then click on More Info. When the System Profiler comes up check the Model Identifier.
Composite is the name for the red, white and yellow RCA plugs on your TV or red, white and S-Video plugs. If you want to use the Composite input on your TV there’s no Mini DisplayPort to Composite. You’ll have to get a Mini DisplayPort to VGA adapter http://www.amazon.com/s/ref=nb_sb_ss_i_1_19?url=search-alias%3Delectronics&field -keywords=mini+displayport+to+vga&sprefix=mini+Displayport+to and a VGA Adapter to TV S-Video RCA Out Cable for PC Video. http://www.amazon.com/VGA-Adapter-S-Video-Cable-Video/dp/B000Y7T5UU/ref=sr_1_7?s =electronics&ie=UTF8&qid=1316369974&sr=1-7
Only the Yellow plug or the S-Video plug for video will work. For sound you'll also need audio cables to the TV using a 3.5mm stereo headphone jack to RCA sound plugs. You attach it from the headphone jack of your MacBook to the appropriate input plugs on your TV http://www.amazon.com/s/ref=nb_sb_noss?url=search-alias%3Daps&field-keywords=min i-dvi&x=9&y=13#/ref=nb_sb_ss_i_2_19?url=search-alias%3Daps&field-keywords=macboo k+audio+cable&sprefix=macbook+audio+cable&rh=i%3Aaps%2Ck%3Amacbook+audio+cable -
iTunes U video files no longer work on my computer since i update to Mavericks. The following message appears on the screen "This movie requires QuickTime, which is not supported by this version of iTunes." I followed a tutorial that suggested to go to Applications/iTunes/Get Info and change to 32 bit. Now my iTunes does not open at all, it says it requires 64 bit. I am a bit confused and disappointed. What should I do to get it fixed? Buy a new MacBook?
Marcello, I am having the same problem. When following the advice of many in the community to start iTunes in 32-bit mode, I get the following error after I have done so:
I am running 10.9.2 on a mac mini.
I am hoping this will be fixed or at least a solid answer could be given that iTunes will no longer support certain types of media going foward. -
Hi guys,
we created a custom WIM Image (Windows 8 Enterprise) with MDT 2012.
Sysprept the Image, Deployed via SCCM 2012 SP1.
Computers are Domainjoined. Error with standard Domain User.
On some computers (not every computer) and not with every user on the first logon following error message arises:
The Group Policy Client service failed the sign-in The universal unique identifier (UUID) type is not supported
It works, when you log in a second time but this error isn't very nice.
Is there a solution for that?
Kind Regards
MartinHi,
The service is responsible for applying settings configured by administrators for the computer and users through the Group Policy component. This issue can be caused by various reasons based on the computer environment.
Can you find any information in event log about this issue?
Here is the related blog in which the steps can solve most of such issues if the issue continuously happen.
http://blogs.msdn.com/b/moiqubal/archive/2012/03/04/how-to-fix-quot-the-group-policy-client-service-failed-the-logon-access-denied-quot-error.aspx
Also, you can refer to the similar thread about this issue:
http://social.technet.microsoft.com/Forums/en-US/4a644219-50ee-494d-b965-e64a8555109e/the-group-policy-client-service-failed-the-signin-the-universal-unique-identifier-uuid-type-is
Since this issue can be related to SCCM, to better help you, please submit a new thread for further help:
https://social.technet.microsoft.com/Forums/en-US/home?category=systemcenter2012configurationmanager
Hope these could be helpful.
Kate Li
TechNet Community Support -
IE11/Win 8.1 error 'Your client does not support opening this list in windows explorer'
I hoping someone might be able to help with this frustrating issue.
I work on a project where we are using various versions of on-line SharePoint (2007/O365). In order to quickly drag and drop folders we need to often open the document libraries by using the 'open in windows explorer view'.
Using the same device, on occassion this works. But often it gives a rather unhelpful message 'Your client does not support opening this list in Windows Explorer'.
I've searched for this issue over the net and confirm that the sites are added to the 'trusted' sites area and that the 'remember you credientials' is checked on logging in.However, the searches do not seem to apply to IE11/Win8.1 or on-line version of sharepoint
(the suggested hot fix is not suitable)
Only this morning, using the same device I was able, for a short while to open in explorer view, and then for no apparent reason, it began to display the error message. I had changed nothing regarding settings or even closed the browser.
Do you have any support/ideas/fixes on how to resolve this.
Many thanks
valHi Val,
sometimes an answer can be found on the internet by typing the error message from your computer into your favourite search engine.
eg.
http://www.bing.com/search?q=your+client+does+not+support+opening+this+list+in+windows+explorer&form=IE10TR&src=IE10TR&pc=HPNTDFJS
see
http://blogs.technet.com/b/asiasupp/archive/2011/06/13/error-message-quot-your-client-does-not-support-opening-this-list-with-windows-explorer-quot-when-you-try-to-quot-open-with-explorer-quot-on-a-sharepoint-document-library-in-office-365-site.aspx
follow the directions given above.... you need to add the domains to your Intranet sites list, not the Trusted sites list.
Perhaps you already have it mapped to your intranet zone....in which case make sure that you have unchecked "Enable Enhance Protected Mode" on the Intranet zone dialog in Internet Options.
If this is happening 'randomly' on client machines, then users are probably changing their internet security settings in Internet Options. Ensure they are accepting the default.... Internet Options>Security tab, click "Reset all zones to default".
Consult with your system administrators to find out if they are applying a custom security template for the Intranet zone... It may be removing the sharepoint domains from the client Intranet zone's domains lists.
HTH.
Rob^_^
Maybe you are looking for
-
SAP query error - 1). [Microsoft][SQL Server Native Client 10.0][SQL Server]Conversion failed when converting date and/or time from character string. 'Received Alerts' (OAIB) SELECT CASE WHEN T0.DocStatus = 'O' THEN 'OPEN' WHEN T0.DocStatus = 'C
-
Where is the Acrobat tab in Word 2013? I checked the Add-in category and it's not disabled. How do I get it back? I am using Acrobat XI Pro.
-
Hi, In F-28 we want system to show invoice w.r.t their age. The more older invoice is the more quickly it should be cleared. How can we achieve it.
-
WebService Publication asks for user and password
Hello, I have a WebService with No Authentication. The problem is that when I try to open the WSDL in the WebBrowser SAP asks for User and Password of the WebAS. I have tried to Consume the WS through a 3rd application and when I try to consume it us
-
Blurry in Bridge, Tack sharp in Photoshop
Huge new issue. Images preview (full rez previews) -- some look blurry in Bridge in the Preview. Then I use magifier or open in PS and it's just fine very sharp. What is this? real drag.