Nexus spanning tree pseudo configuration

Hi
I am trying to understand the pseudo configuration commands in a Nexus hybrid topology.
I have vlans a, b and c only in the vPC side of the topology. I have peer switch configured and the same stp priority on both switches.
In the standard Spaning-tree topology I have completely seperate vlans x, y and z.
What should I be configuring in the pseudo config section ? Do I define a pseudo root priority for all vlans a, b, c and x, y, z or just for the standard spanning tree vlans x, y and z. I need to avoid and, even short, spanning tree outages if I take one Nexus out of service for a short time.
My thinking is that if one Nexus is out of service the physical mac will be used and potentially reduce the root priority of the vPC vlans causing a TCN and STP recalculation in vlans a, b and c. This can be avoided by configuring a pseudo root priority for all Vlans lower than the current spanning tree priority shared by the vPC peers. Is this correct ? However, since I have a shared priority of 8192 on current vPC vlans will configuring, for example, a pseudo root priority of 4096 on those vPC vlans won't this also cause the TCN and recalculation I am trying to avoid ? Is the benefit of the pseudo root config only obtained if it is configured at the start when the vPC is formed and prior to the peer switch command being issued ?
Thanks, Stuart.

Hi Ajay,
It is recommended that switch-to-switch links are configured with the spanning-tree port type normalcommand. The one exception is the vPC peer-link which is recommended to configure with the spanning-tree port type network command.
Take a read of the Best Practices for Spanning Tree Protocol Interoperability from page 56 of the vPC Best Practice Design Guide for further information on this.
Regards

Similar Messages

"Peer-switch" command on vPC domain and spanning-tree priority interaction

Hi guy,
We have 2 N7K (N7KA and N7KB) which will be running vPC in hybird and pure vPC environment.
I have a question about the Hybird and pure vPC environment. With the "peer-switch" command enable, should i tune the spanning-tree priority to be the same for all the vlan running on vPC on both N7KA and N7KB? This way, when i enter the "sh spanning-tree vlan X(vPC vlan) detail" command on N7K, it will list both N7K announc itself as "We are the root of the spanning tree".Also the switch running spanning-tree with N7K vPC vlan (Hybird), will see both N7K has the same priority (4096), and it is not desirable for a spanning-tree environment. Therefore, i used the "spanning-tree pseudo-information" on N7KB to tune the spanning-tree priority to "8192" and the switch running spanning-tree with N7K will list N7KB has a priority of 8192(perfect).
However, I notice some strange "show" output on the switch running Port-channel with the N7KA and N7KB. The "Designated bridge" priority is flapping as show on the switch. It is constantly changing between "4096 and 8192" with the same vPC system wide mac address.
Entering the "sh spanning-tree vlan X detail" command repeatly on switch with port-channel toward N7KA and N7KB.
>>sh spanning-tree vlan 10 detail
Port 65 (Port-channel1) of VLAN10 is root forwarding
Port path cost 3, Port priority 128, Port Identifier 128.65.
Designated root has priority 4106, address 0013.05ee.bac8
Designated bridge has priority 4106, address 0013.05ee.bac8
Designated port id is 144.2999, designated path cost 0
Timers: message age 15, forward delay 0, hold 0
Number of transitions to forwarding state: 1
Link type is point-to-point by default
BPDU: sent 5, received 603
one sec later.
>>sh spanning-tree vlan 10 detail
Port 65 (Port-channel1) of VLAN10 is root forwarding Port path cost 3, Port priority 128, Port Identifier 128.65. Designated root has priority 4106, address 0013.05ee.bac8 Designated bridge has priority 8202, address 0013.05ee.bac8 Designated port id is 144.2999, designated path cost 0 Timers: message age 15, forward delay 0, hold 0 Number of transitions to forwarding state: 1 Link type is point-to-point by default BPDU: sent 5, received 603
Configuration:
N7KA
spanning-tree vlan 1-10 priority 4096
vpc domain 200
peer-switch
N7KB
spanning-tree vlan 1-10 priority 4096spanning-tree pseudo-information vlan 1-10 designated priority 8192
vpc domain 200
peer-switch

We have a issue similar to this in our environment. I am trying to upgrade the existing 3750 stack router with 2 Nexus 5596 running VPC between them. For the transition I have planned to create a channel between 3750 stack and 5596's. Once this environment is set, my plan is to migrate all the access switches to N5k.
The issue is when I connect the 3750 port channel to both N5Ks, all the Vlans on 3750 started to flap. If I connect the port channel to only one N5K everything is normal; but when I connect the port channel to both N5K running VPC, vlans are flapping. Any idea what is going wrong here? Am I missing something?

What is the command to check the changes in the spanning-tree topology?

What is the command to check the changes in the spanning-tree topology?

Hi,
Few commands which would help are:
1- Show spanning-tree detail
2-show spanning-tree detail | in ieee|from|occur|is exec >> This will give from were the changes occuring- Ex:
C6K1#show spanning-tree detail | in ieee|from|occur|is exec
VLAN0001 is executing the rstp compatible Spanning Tree protocol
Number of topology changes 9536 last change occurred 00:00:29 ago
from GigabitEthernet4/6
3- show spanning-tree active *& show spanning-tree root >> Will give you the root information.
4- show spanning-tree inconsistentports >> If there are any port which are inconsistent state due to STP features.
STP running MST:
===============
show spanning-tree mst configuration >> Need to check and match the same outputs with the other switches running in the same MST domain/region.
show spanning-tree mst detail
show spanning-tree mst <name of the region>
Debug on STP:
============
debug spanning-tree events/bpdu >> would be good but to be run with more cautious.
HTH
Inayath
*Plz rate if this info is usefull.

Spanning Tree MST per Vlan, best practice

Hi Community.
I did the following MST Spanning Tree Config
spanning-tree mst configuration
name xxxxxxx
revision1
instance 1 vlan 1, 10-20, 25, 30
So I added every Vlan to the config which we use. But every time when I add one more vlan to the config the whole network get a little outage.
I see lots of MAC Flaps on ports with two Server links and the outage is for some seconds.
Is it a better practice to add all possible Vlans to the config. So I do the config like that:
instance 1 vlan 1-4096
What you think.
Best Regards patrick

Hi,
So I added every Vlan to the config which we use. But every time when I add one more vlan to the config the whole network get a little outage.
Correct, that is normal behavior with MST.
I would just add "instance 1 vlan 1-4094" this way there is no outage when you bring up a new vlan.
HTH

Spanning tree for VLANS

Hi,
I need an answer to this puzzling scenerio i have been asked to work with.I have two vlans with about 10 switches on each end and there is a link switch that has a connection to both sides of the VLAN. I have been asked to create a singular spanning tree for the entire scenerio. how can i go about this.
please i am awaiting the opinions of anyone knowledgable in this line. thanks.

Hi, I agree you can config MST on your router to reduce the number of spanning tree instances runing on the switch from one per vlan. You will have to map your vlan range to the MST, useful CLI commands are
spanning-tree mode mst
spanning-tree mst configuration
name (name)
revision( revision number)
instance (number) vlan (vlan range)
check your config using
show spanning-tree mst configuration.
Hope thsi will hlep you get started.
DW

Spanning-Tree MST

Hi,
we have the following configuration on our switches
spanning-tree mode mst
spanning-tree extend system-id
spanning-tree mst configuration
name test
spanning-tree mst forward-time 4
when we have a failover convergence time was about 8-10 seconds outage is there anything on the above config that suggest's this could be causing the delay? i thought MST was fast convergence times?
Thanks

i will try and you this later on. Not sure it was already in place what are the difference's between them both i thought MST can have multiple vlans per region so better design. Is RSTP not the same as PVST? not done much spanning tree as of yet. so not had chance to look at the differences?
Thanks

Do I configure spanning-tree port type ed trunk on LACP port-channels

Hello,
Can't seem to see a clear answer and wondering if something could offer some advice please?
We are using LACP aggregation across all our 10 gig attached servers and also trunking them. We're running a VPC pair of 5596 Nexus.
For a standard trunk port I always add the spanning-tree port type edge trunk to the interface config.
However I think I should be adding this to the overiding port-channel config. At present a colleague has configured the VPC below omitting the spanning-tree port type config.
interface port-channel100
description a-server
switchport mode trunk
switchport trunk allowed vlan 100
vpc 100
The port member configs are these which do contain the spanning tree port type:
interface Ethernet1/1
description a-server(1)
switchport mode trunk
switchport trunk allowed vlan 100
spanning-tree port type edge trunk
channel-group 100 mode active
I always try to keep the overiding port channel config the same as its members and obviously for most config, you can't have disparate configs anyway.
However for the spanning tree config the NexOS allows you to have the members with spanning tree port types and not have to reflect that in the port-channel.
However I have this issue with STP:
Switch1# show spanning-tree interface po100
Vlan Role Sts Cost Prio.Nbr Type
VLAN0100 Desg BKN*200 128.4996 (vPC) Network P2p *BA_Inc
Is this due to the inconsistency with my port channel to member configs?
Any advice would be gratefully accepted.
Thanks!

Hi Paul, there are some parameters you can define on individual ports and there are some of them that will be inherited from the port-channel configuration no matter what has been configured under the infidividual ports. Spanning-tree configuration is one of the inherited ones. As soon as the port joins into a port-channel, it will start to use spanning-tree settings under the port-channel. When it leaves the channel, then it can continue to use the individual configuration.
There is a nice summary here under NX-OS Interface Conf Guide > Port-Channel Conf:
http://www.cisco.com/en/US/docs/switches/datacenter/sw/6_x/nx-os/interfaces/configuration/guide/if_portchannel.html#wp1798338
Evren

Method-long Spanning-Tree Cost - Nexus and VSS

Hi,
I'have a DC topology with 2x6509 VSS, 2 NX7K, 10xNX5548 and NX2K dual-homed.
My question is about spanning-tree cost in method-long
Between VSS(L2/L3) and NX7Ks(L2) i have 8x10giga links on a crossed VPC, from NX7K point of view, the pathcost to the root (wich is the VSS), is 200.
is this correct ?
what is the cost for 2 and 4x10g links ?
thanks for your replies
Franck

Yes one of the interfaces will be in blocking.

Nexus 5596 Ethernet Port Configuration

I have a Cisco Nexus 5596 with 48 Ethernet Ports (two of which are now configured for Fibre Channel). It has a FEX attached to it as well.
I was able to configure ANY Ethernet port with the typical interface commands when in interface configuration mode. However, I can now only configure existing and new Port Channel interfaces, FEX ports and standard Ethernet ports that have never been configured before.
If I try to configure an Ethernet interface that was configured in the past, I only seem to have access to global interface commands when in interface configuration mode. I can set spanning-tree, duplex, speed or any other interface parameters. The CLI acts like I'm not in interface config mode, but the prompt shows that I am.
Anyone else seen such a thing? I am logged in as admin.

Hi Mark
I suspect the interface in question is configured to be in a channel. Once an ethernet interface is configured to be in a port-channel. most interface commands need to be configured under the port-channel interface
Thanks
-Prashanth

Spanning Tree and Admin mac address issues srw2048

Ok, I have a somewhat complex problem and hopefully someone may shed some light or have an idea as to whats wrong.
First the scenario:
I have two Cisco Cat 6509's etherchanneled to each other via two fiber cables. One of these is the STP/RSTP root. I have two SRW2048's.. one trunked to each of these 6509 switches. There is also a trunk between the SRW2048's. All this is to create a redundant topology so that if one of the switches fail's the others can still forward packets to each other. Of course the scenario described is in fact a loop that should be handled by STP/RSTP. I have RSTP enabled on all the switches in the scenario (PV RSTP on the cisco switches as they only do Cisco's brand of per vlan spanning tree). There are 3 vlan's configured on each of the srw2048's (2,55,96). There are corresponding vlan's also on the 6509's. I have put the srw2048's management interface into vlan 2.
The problem:
I need to forward packets between the srw2048's primarily and only use the 6509 that is not the root when a failure happens. I have configured the non-root 6509's spanning tree cost on the etherchannel to be higher then the alternate path through the srw's to the root. I can hook everything up and view the spanning tree and see that the srw2048's interface that goes to the non-root 6509 is blocked, and all other interfaces on the other switches are forwarding. I can in fact ping and get to the admin interface on all the switches. Then for some strange reason the admin interface of the srw2048 plugged into the non-root 6509 stops responding. If I disable either the interface its plugged into on the 6509 or the other srw2048 everything starts working again. Sometimes it responds after many failures for no apparent reason. I looked into the mac-address table on the 6509's and they are conflicting, pointing to each other for the mac-address of the broken srw2048. When I clear the mac-table the admin port comes back for about 5 seconds then again goes dark. When reviewing mac-table on the 6509's they are back to pointing to each other. The odd thing (although I haven't confirmed this completely) is that hosts placed into vlan 2 on that same srw2048 seem to work fine. If there was an STP loop or something misconfigured, I would expect it to effect any host in vlan 2 or the other vlan's for that matter on the srw2048 that stops responding. Alas, I am stuck because I need to manage this switch remotely. My only thought is that for some reason even when the STP status is blocked the broken srw2048 is still sending out arp's of its admin interface and bypassing the STP protocol. I have no way to confirm this, but maybe someone has an idea as to what I'm doing wrong, or otherwise offer a solution. For now, I simply removed vlan 2 from the 6509 that the broken srw2048 is plugged into and everything seems fine.
My apologies for such a long post, but this is somewhat complicated. Thanks in advance for any info.
-Geoff
Message Edited by gmyers on 08-19-2008 10:35 PM

To follow up, I had a ticket open with Linksys about this for about 3 months with no resolution. I submitted packet captures, stp outputs, etc and no luck. I gave up and basically had to revert to a manual failover for redundancy. It's no perfect or fast, but it works every time.
Unless linksys issues a firmware upgrade with this as a fix, I doubt we will be able to ever resolve this on our own.

ISE - 802.1X - Loop not detected by spanning-tree

Hello,
I have recently implemented the 802.1X on switchs 3750-X running 15.0(2)SE IOS version.
The spanning-tree bpdufilter and bpduguard are globally enabled on the switchs.
A user has created a loop on the network by connecting its Cisco IP-Phone twice on the network : one wire connected normally from switch to the RJ-45 phone connector and the second wire that should be connected to the PC had also been connected to the switch !
The loop created has not been detected by the switch !
I have made several tests and re-created the problem 3 times on 4 (only one time, the loop has been detected by bpduguard 20 seconds after the port up).
Notice that without 802.1X configured on the same switch port, the loop is quickly detected and ports are err-disabled shutdown.
Switch port with 802.1X is following :
interface GigabitEthernet1/0/9
switchport access vlan 950
switchport mode access
switchport nonegotiate
switchport voice vlan 955
no logging event link-status
authentication control-direction in
authentication event fail action next-method
authentication event server dead action reinitialize vlan 950
authentication event server dead action authorize voice
authentication event server alive action reinitialize
authentication host-mode multi-auth
authentication order dot1x mab
authentication priority dot1x mab
authentication port-control auto
authentication periodic
authentication timer reauthenticate server
mab
dot1x pae authenticator
dot1x timeout tx-period 10
storm-control broadcast level 10.00
storm-control multicast level 10.00
spanning-tree portfast
If I change the host-mode to multi-domain, a MAC violation restriction occurs and shutdown the port. But this is not the config I need.
Is there any reason for spanning-tree not works properly with 802.1X ?
Thanks,
Olivier

Hello Olivier
When using bpdufilter, bpduguard and portfast all at the same time there are many things going on which are not well documented. Now when you add 802.1x to the mix then you really have no documentation. I had to do many labs on my own to finally have my configuration, and also discovered some bugs. According to my experience you shouldn't use bpdufilter and you should use bpduguard on the switchport not in the global config.
Please read the following links about the differences between global and port bpdufilter, differences between global and port bpduguard, configuring bpduguard along with portfast , configuring bpdufilter along with portfast, and configuring bpduguard along with bpdufilter.
http://aitaseller.wordpress.com/2010/01/17/bpdu-filter-vs-bpdu-guard-what-is-the-difference/
http://costiser.wordpress.com/2011/05/23/subtle-difference-for-portfast-bpdufilter-used-together-globally-or-at-interface-level/
https://learningnetwork.cisco.com/thread/21103
http://blog.ipexpert.com/2010/12/06/bpdu-filter-and-bpdu-guard/
Please rate if this helps

Switching Best Practice - Spanning Tree andEtherchannel

Dear All,
Regarding best practice related to Spanning Tree and Etherchannel, we have decided to configure following.
1. Manually configure STP Root Bridge.
2. On end ports, enable portfast and bpduguard.
3. On ports connecting to other switches enable root guard.
In etherchannel config, we have kept mode on on both side, need to change to Active and desirable as I have read that mode on may create loops? Please let me know if this is OK and suggest if something missing.
Thank You,
Abhisar.

Hi Abhisar,
Regarding your individual decisions: Manually configuring the Root Bridge is a natural thing to do. You should never leave your network just pick up a root switch based on default switch settings.
On end ports, using PortFast and BPDU Guard is a must especially if you are running Rapid PVST+ or MSTP.
Regarding the Root Guard on ports to other switches - this is something I do not recommend. The Root Guard is a protective mechanism in situations when your network and the network of your customer need to form a single STP domain, yet you want to have the STP Root Bridge in your network part and you do not want your customer to take over this root switch selection. In these cases, you would put the Root Guard on ports toward the customer. However, inside your own network, using Root Guard is a questionable practice. Your network can be considered trustworthy and there is no rogue root switch to protect against. Using Root Guard in your own network could cause your network to be unable to converge on a new workable spanning tree if any of the primary links failed, and it would also prevent your network from converging to a secondary root switch if the primary root switch failed entirely. Therefore, I personally see no reason to use Root Guard inside your own network - on the contrary, I am concerned that it would basically remove the possibility of your network to actually utilize the redundant links and switches.
Regarding EtherChannels - yes, you are right, using the on mode can, under circumstances, lead to permanent switching loops. EtherChannel is one of few technologies in which I wholeheartedly recommend on relying on a signalling protocol to set it up, as opposed to configuring it manually. The active mode is my preferred mode, as it utilizes the open LACP to signal the creation of an EtherChannel, and setting both ends of a link to active helps to bring up the EtherChannel somewhat faster.
If you are using fiber links between switches, I recommend running UDLD on them to be protected against issues caused by uni-directional links. UDLD is not helpful on copper ports and is not recommended to be run on them. However, I strongly recommend running Loop Guard configured globally with the spanning-tree loopguard default. Loop Guard can, and should, be run regardless of UDLD, and they can be used both as they nicely complement each other.
My $0.02...
Best regards,
Peter

SGE2010 switches, VLAN's and a blocked port in spanning-tree

Folks,
I have 2 switch groups.
2 SGE2010's with VLAN's defined as 10,20 and 30
Vlan 10 is the management VLAN, and it uplinks to our border router.
Vlan 20 is the workstation VLAN, and all workstations point to the switch as their default GW
Vlan 30 is the ip phone VLAN, and all phones use this as their gateway.
I would like to put a LAG between said switches, we have some servers on the ip phone switch that need to be accessed by the workstation clients, and the single 100mb link through the router is probably not going to be enough.
As I understand it, because the switches have different networks on them, a simple lag will not work. I did create a lag, and assign ip addresses to each side, however in that mode, it doesn't appear I can block vlan 10 from transiting the LAG, and with out that block I will end up with a logical loop, and spanning-tree will block one of the uplinks, or the LAG itself.
I have attached an image with a diagram of our current set up.
Any help/advice would be much appreciated.

Tom,
I remember our conversation a few weeks ago. I did not get a chance to have a go at MSTP, mainly because I have no expierence with it, and looking at the configuration properities, it looks a little daunting.
It has also been a very busy few weeks with the deployment of 200+ phones across several sites, and the system is functioning great with out the LAG trunk, I am just trying to plan for the future.
I made a few postings a few weeks ago, one here and one on the Cisco forums on reddit, and a user there gave me some advice I have been unable to make work (I think it's just wrong), but I would love to go this route if it is in fact possible.
Here is the thread : http://www.reddit.com/r/Cisco/comments/x91tc/vlan_trunks_spanning_tree_and_a_port_blocked/c5kskch
This user implies it's possible to block a VLAN across the LAG which would end the logical loop problems.
It looks like his advice is to make the LAG into a trunk, and then block specific VLAN's from transiting it, but in trunk mode, I can't assign it an IP, so I am sorta wondering how exactly you transport packets across it.
Can you confirm that his advice is in fact incorrect?
If MSTP is my only route, then I suppose it's time to dig into the docs and see If I cant get it up and running.

Dlsw spanning-tree

Hi, my name is fabio and i´ve a problem with dlsw.
When i´ve configured de dlsw in a router 3600 the router 7206 that has the conection with mainframe, the same lost the comunication e appears the messagem in 3600 router, look at below:
Note: A random Spanning Tree Bridge Identifier address of 0000.0cfe.6628
has been chosen for Bridge Group 50 since there is no mac address
associated with the selected interface.
I´am putting the scheme in .ppt.
Can i sending configurations of 3600 and 7200 to help you.
thanks

Fabio
I'm not sure what the issue is here. The mac-address of the end-stations will not be visible in the 4948 as the SNA traffic is encaps'd in ip. Can you supply sh vers, sh runn, sh dlsw pe, sh dls reach, sh dls circuit, sh bri from the 3640 and the 7206. What is the mac-address of the end-station to which mac-address is it trying to connect ?
Matthew

2950 spanning tree issue

Here is the problem we are having , we have a 2950 hooked to a 6509 hybrid dist box with approx 90 vlans on it . We hook up a new 2950 and we get the following message, Dec 21 19:47:45.116: %SPANTREE_VLAN_SW-2-MAX_INSTANCE: Platform limit of 64 STP instances exceeded. No instance created. Ok , I know about the spanning tree issues with the 2950 only having limited PVST instances . But up at the dist side we have "manually pruned off all but 5 vlans on the trunk feeding this 2950 with the "clear trunk" command . I thought manually pruning off the vlans from the trunk would eliminate this problem , maybe i have a misunderstanding of how this works. Also the message on the 2950 complains about it only having 64 instances of spanning tree yet when you do a "show vtp status it says it supports 250 instances locally so whats up with that , 2950 running 12.1.22EA4 . So I guess I'm asking is there any way around this for the 2950 . Also in client/server mode do you have to manually prune off the vlans on both the server side and the client side ??

Hello Glen,
I guess instead of manually pruning the VLANs off the trunk, you could also try and enable VTP pruning globally on the 6509 (set vtp pruning enable). I assume you have the 6509 configured as the VTP server (set vtp mode server) ?
I am not sure if CatOS and IOS defaults to the same VTP version, can you check this (with 'show vtp domain' for CatOS and 'show vtp status' for the IOS switch) ?
Also, in a purely IOS environment, manually pruning VLANs off a trunk requires doing that only on the server side, but with a mix of CatOS and IOS, it might have to be done on both sides, you might want to give it a try and use the 'switchport trunk allowed' command on the 2950 as well...
Regards,
GP

Nexus spanning tree pseudo configuration

Similar Messages

Maybe you are looking for