[nForce] K7N2 Delta2-FSR and AX-7 Heatsink

Hi, does this heatsink fit on this MB? It looks like the chipset HS & fan are too close. Anyone have this combination? Also is this a good socket a board, there seem to be people with alot of problems? Thanks

Dr Stu, I have'nt bought the board yet, I just want to upgrade my kt3 ultra2 in my sig, want to get dual channel memory, 8X AGP and sata to get the most speed out of my XP2700. I have already bought another 512mb of Crucial Ballistix for the dual channel. I'm looking for a good socket A board before they go away! I know I'm pushiing my PS with only 18amps on the 12v side, but it has the xtra 4 pin connector and it's a good quality. The link Fredrik so kindly provided is what it looks like. It has been a decent sink for me. It is 80 X 80 mm @ the aluminum fins. Actually I had to lap mine to get a shiney surface, it had machine marks on it. Thanks
P.S. The K7N2 looks like it's feature pack, just wondered if it's a good stable board

Similar Messages

K7n2 delta2-fsr and 2600+ Barton o/c problem!

Hi my system consist's of :
Athlon xp 2600+ Barton
k7n2 delta2-fsr ( B3 bios)
2*256 Twin Mos cl 2.5 Dual channel
GForce4 MX 440
ASUS 300w (+3.3V-> 28A, +5V -> 30A, +12V -> 18A)
The problem is that i can't go stable above 178 FSB whatever the Vcore is!
The cpu temperature seems to be low enough ( 38 idle)
With my previous mb i had reached easy 192 with the same processor.
The DOT is disabled!
Any ideas?

Quote from: BOSSKILLER on 27-January-06, 20:01:25
enable acpi.
set dot to default
set nvmm enabled
set fsb:ram 1:1
agp to 68mhz
nv/ati speedup leave auto
cpu interface set to normal
give nesesery CPU Vcore...
set DIMM Vcore at minimum 2.70
leave memory timmings to optimised if you dont know what to set.
start from memtest86 to be sure its memory probs. make sure there is no errors at test number five.
start increase DIMM Vcore if errors is detected till 3.0V its safe mobo is dimm is undervolted after 2.9V isnt give actual core what is suppose to be. let we know how its going.
make sure 1st that you dont have any memory fabric malfuction. this can be done by testing one stick then test other stick with memtest86.
at all i think that your CPU want more Vcore to be stable when you change FSB to higher. set CPU Vcore to 1.85V to be sure.(standart cooler can handle it) or best way is to lower multipler and set FSB to 200FSB to test memory if toyr CPU is unlocked.
First of all i'have already tested my cpu and the rams with my previous mobo,so unless this mb has a problem i should go up to 192fsb without any problem!
Now i can't understand why should i raise the Vdimm since the ram runs at lower frequency than the deefault?
Anyway i'll try all you say above and let's hope that everythimg will go ok!
Thanks

[nForce] K7N2 Delta2-FSR PCI revision Q.

What is the PCI revision for this motherboard?
Can't find it anywhere on official page or somewhere else.
thx in advance

Dr Stu, I have'nt bought the board yet, I just want to upgrade my kt3 ultra2 in my sig, want to get dual channel memory, 8X AGP and sata to get the most speed out of my XP2700. I have already bought another 512mb of Crucial Ballistix for the dual channel. I'm looking for a good socket A board before they go away! I know I'm pushiing my PS with only 18amps on the 12v side, but it has the xtra 4 pin connector and it's a good quality. The link Fredrik so kindly provided is what it looks like. It has been a decent sink for me. It is 80 X 80 mm @ the aluminum fins. Actually I had to lap mine to get a shiney surface, it had machine marks on it. Thanks
P.S. The K7N2 looks like it's feature pack, just wondered if it's a good stable board

Msi k7n2 delta2-FSR and problems with memories(ddr 400);help me!!!

hello!!!!.
I am very frustrated because is imposible that memories work fine to 200*2.I´ve tried twinmos and now ocz premier ddr-400.When i used memtest i have a lot of errors and frozen in windows.
If i choose vdim 3.30 memtest no errors but this is a voltage very high.I don´t now what can I do.
Is a bug of this motherboard?
In other forum tell me that this motherboard don´t work good with memory to 400 but the motherboard has dual channel.
i need help.
thanks!
pos data=sorry for my english

Quote from: Stu on 26-March-06, 01:48:25
how can you have a stable OC if you have memory errors?
i don´t Know but prime no errors.
Quote from: Stu on 26-March-06, 01:48:25
forget about the OC for now, and get it working properly at stock speeds, then you can worry about getting an OC right
I have tell than 166 cpu(default values in bios),there are a lot of errors(more of one hundred and froozen in windows) in memtest.

[nForce] K7N2 Delta2 LSR and XP-M 2600 Help!!!

Hi,
I'm having trouble just getting this board to run stable at any speed.
The orignal idea was to put this system together from spare parts and use it as a second sytem to learn about OCing, but somehow I ended up buying mostly new parts and I can't even get it set up to run stable at BELOW stock speeds.
380W Antec Truepower 24A 12v
Kingston HyperX KHX 3500K2/1g (installed in slots 1&3 - middle slot empty)
Artic Coolling Copper Lite
Thermalrigtht NB-1
XP Home
The problem is Windows just locks up. I don't get a BSOD or error messages.
I've tried different ram voltages from 2.5 thru 2.7
I've tried using Patroit XBL 3200 TCCD
Am I overlooking something obvious?
Thanks,
L.J.

Quote from: DaveR on 28-June-05, 17:29:43
Excellent
download cpu-z
memory tab tells you actual memory timings
spd tab gives you the manuufacturer's programmed timings
I'm still on bios b3 as it is only one that allows me to change memory timings with DOT disabled.
keep us informed as to your progress
Thanks Dave. I don't know why I didn't remember that.
Good Luck
Jeremy

K7n2 delta2 FSR and PENTAGRAM FREEZONE QC-80 Cu, HELP

does anybody here use this fan in k7n2 delta mobo? i wonder if it will fit under the PSU in standard case... please tell me, or give some pictures.

Speak any Polish? Except for that I only find:
http://www.aoaforums.com/forum/showthread.php?t=30318 on the Internet.
On
http://www.cooling.pl/product_info.php?products_id=472
there is a picture you can enlarge.
http://www.in4.pl/recenzje.htm?rec_id=211
http://www.in4.pl/recenzje.htm?rec_id=211&rectr_str_numer=2
have more pictures.
It looks a bit like it would need the 4 holes around the socket, which not many new MSI cards have, but I'm not sure. What makes me thinks it nees the 4 holes is, that it should be able to fit many different processors.
My Polish is a bit rusty , but this seems to be the home page:
http://www.mmv.pl/produkty_new/szczegoly.php?id_grupy=14&grupa=coolery&id_produktu=1

K7n2 delta2-fsr and 2600+ Barton problem!

Hi!I just bought my new msi mobo and i have alraedy problems!The problem is that the mobo dosn't recognize the defult bus of the proc which is 166, but it set's it as 100, and now my proc is running at 1150 instead of 2600!
If i change the bus i can't even log in at windows!
i have the B5 bios.I tried to flash it but i get the message that the "Flash rom is write protected"!
My tempreture is below 40!
Any advice?

Quote from: pigassos on 19-January-06, 22:19:34
Hi!I just bought my new msi mobo and i have alraedy problems!The problem is that the mobo dosn't recognize the defult bus of the proc which is 166, but it set's it as 100, and now my proc is running at 1150 instead of 2600!
If i change the bus i can't even log in at windows!
i have the B5 bios.I tried to flash it but i get the message that the "Flash rom is write protected"!
My tempreture is below 40!
Any advice?
"now my proc is running at 1150 instead of 2600"
Barton 2600+ you wana run at 2600Mhz...???nice overclock you gona make dude..

MSI K7N2 Delta2-FSR & Dual Memory Problems

Just recently I decided to upgrade my girlfriend's computer for her. Upgrade new PROC, MOBO, MEM. The proc is a AMD Athlon BARTON 3000+ OEM, Mobo is the MSI K7N2 Delta2-FSR and MEM is from PQI both are dual channel and in same package (identical) 512MB x 2. I thought it was an easy set up and everything and everything in terms of hook-ups was... I loaded XP and it gave me a crap load of errors, but I manage to load all of XP. Then came installing Adobe softwares, it kept saying "installing...." in an infinte loop and then froze on me. I skipped installing Adobe software and decided to install World of Warcraft Game. When I loaded the game, it popped up with errors installing, but it managed to install. WHen time to play the game; however, it kept crashing, restarting, and freezing. I noticed the system was a little bit laggy even though there was 1 gig of ram. So as a Geek Squad tech I am, I started to tweak and mess with it. I figure it was the MEMORY and I tried it and thought it was bad memory...
Yes it was memory when I tested with MEMTEST86 for dual channel ram, It came up with RED ERRORS all across the screen. So I decided to test each stick individually and each stick PASSED! I even tried each of the different slots on the motherboard and it all passed as SINGLE individual rams. I figure the first test with dual ram was just some mistake, loose RAM or something, so i decided to pop the DUALs right back in, in different combination and I kept seeing Red errors all over as well.
So my conclusion is :: Motherboard is bad. I contacted NEWEGG, but they will not refund my money as it has been over 30 days. I wish I would've known earlier... Anyways, So im stuck with exchanging for same mobo or find answers, but I think doing exchange will not do any good if this is a known problem.

Quote from: DaveR on 28-October-05, 01:38:08
Just to confirm; they are fine together in single channel, slot 1 and slot 2? Dual channel is purple + green slot, i.e slot 1 and 3 or 2 and 3. Or are you saying they can't work together in any combination of slots?
there will be a label on side of your psu stating max amps to +3.3V, +5v and +12v rails, i.e +3.3v = ?A, +5v = ?A, +12v = ?A. For example my psu is: Antec TrueBlue480: 30A/3.3V, 38A/5V, 28A/12V
Maybe your psu is not up to the job
You did load the chipset and graphics drivers didn't you?
You are correct sir... any combination of slots 1&3 or 2&3 will give error.... each as individuals 1,2,or3 will pass. The PSU amps readout are as follow:
+5v 40a Red, +12V1 16A yellow, +3.3v 35A orange, +12v2 18a yellow/black, -5v 0.5a white, -12v 0.5a blue, +5vsb 2.5a purple, pg gray.
I have loaded the chipset drivers from the CD it came with, and the graphics drivers are from ATI.com latest version. I will try and update the Nforce driver from Nvidia's site, but I don't see the chipset as the cause of this problem.
EDIT: In any combination of slots used, the read outof of MEMtest is single channel. Only slots 2&3 will have a read out of DUAL DDR channel 128bits. Slots 2&3 Will still have errors though...

MSI K7N2 Delta2 FSR - memory issue

I've got MSI K7N2 Delta2 FSR and 512mb DDR400 Kingston Value Ram CL3. They work fine when I set them on a optimized settings and 166mhz. If I try any better timings then my pc wont be stable. I tried to set higher voltage, but nothing helps. I thought that I bought shitty memory, but when I set manually the same settins as optimized then my pc crushes. It isn't stable until I set optimized setting. Even if i set manually worse timings than optimized it will crush. I also tried with old TwinMos DDR266, witch was able to run with the best timings on my old MSI K7T266 Pro2(KT266A). I tried any other settings, but only optimized worked fine. So probably it is coused by motherboard, not memory. It has newest avalible bios and I installed newest nvidia drivers (also tried with old one, witch was on a cd bunled with mobo). Does anybody have a solution ??

I could get that RAM to work in Dual channel (even though their weren't matched pairs) at 2.5-4-4-8, synched with CPU FSB (1:1) at 200Mhz ... Like you said, pretty good bang for the buck. Although The Corsair I now have makes a difference (for 100$ more)...
System 1: MSI K7N2 Delta2-ILSR, XP2500 Barton (@2200Mhz)(11*200), Corsair TWINX 1024C2 (@2-3-3-6), XFX TI4200-128M (@300-590), Seagate 120G SATA
Western Digital 200G SATA, Antec Sonata 380W TruePower.
System 2: MSI K7N2 Delta2-LSR, XP2500 Barton (@2343Mhz)(11*213), Platinum 512M (@3-4-4-8), Powercolor 9600 Pro 256M (@550,460) Western Digital 160G SATA, Antec Sonata 380W TruePower.

K7N2 Delta2 FSR - no post

Ok....just got this board two days ago and installed windows xp pro and updates without a glitch. Then, I installed battlefield2 and played off and on for the rest of the day. Everything worked great ...until, right in the middle of battle, I got the blue screen of death but there was no text...just blue. I then restarted the computer and went into bios to check the temperature, which seemed fine. CPU was at 45c. Windows booted then i started the game again. I played for a while then BAM!!! blue screen again. Repeated checking temp and booted windows again. Started the game and as soon as it started, blue screen. So, I rebooted again. This time I got the award screen and it said "Bios Rom Checksum error. Insert system disk. Well, I do not have a system disk, so I turned it off and came to check here. I've read about all the things suggested like taking battery out, unplugging, pressing insert...blah blah blah. I also downloaded the newest bios and was prepared to flash it. But, the next time I turned it on, I got no post. CD drive spins up...hard drive crunches, fans turn on...but no floppy seek, no video, no beeps, keyboard freezes(i check by pressing caps lock and watch for the light). I am at a loss as to what would cause this, and have even submitted a help request, which says I will recieve a reply in the next couple hours...but have yet to receive such reply. I have tried ALL new hardware in this motherboard along with the originals in another motherboard....all hardware is fine...and other hardware makes no difference in this board. Help
Motherboard: K7N2 Delta2 - FSR
Revision: MS - 6570E Ver: 1.0
CPU: AMD Athlon XP 2500+ barton
Heatsink: Thermaltake Copper Plated
Fan: Silent Boost

It's hard to find out things, of course, what it is if one is not allowed to ask what the situation is. The BIOS message checksum error would suggest it returned to basic 100 MHz, which it didn't like. Why did it do that?
The processor is a 166(333) MHz. If you had not so good DDR400 RAM there might be problems, or if it was very fast. What RAM have you got? Or rather, did you have?
If you don't want questions, but something to do, I would suggest you stripped the system of all connected devices - including the power cable and power connections. Also take out the battery and the memory. Please study the memory real close. Go do something else for half a day or so.
Next with only the processor on reconnect only the PSU to the mobo, and have a test run for POST. Hopefully you'll get to BIOS, which will give you all kind of beeps.

MOVED: [K7N2 Delta2-FSR] Unstable when DOT disabled

This topic has been moved to Overclockers & Modding Corner.
[K7N2 Delta2-FSR] Unstable when DOT disabled

Sorry! I've missed this section (overclocking&modding). So, You'll say the problem is probably RAM. I'll try to unplug one stick of mem and i'll see. I'll try flash the B30 BIOS If you say that it's most stable than b40 & b50. BTW. processor easly overclocking at FSB 200 and 1.700V - prime95; 8hour blend test; 0warnings 0errors!
About the PSU: On the beginning I have 400W Megabajt (megash#$) so I was afraid of the future of my device (mean: stuff, comp) and I was change it on ModeCom 350 (GTF). It's most, most, most, most stable than that megash#$.
PZDR [Take Care]

MOVED: [nForce] K7N2 D2-FSR cant get in window after manual setting

This topic has been moved to Overclockers & Modding Corner.
[nForce] K7N2 D2-FSR cant get in window after manual setting

I'm a bit of a noob at o/c so not sure I can give you sound advice.
pci is unlocked I think, though if use core centre then you can control it-I'm not using corecentre.
are you using priority 10 for prime 95 and In-place FFT's torture test? I believe that is most demanding. If you getting reboots then you're overclock is not stable, need to lower fsb and retest. Your psu is probably marginal as well so maybe that isn't quite strong enough to be pushed further. Can you try beefier one?
I don't know how far you can push vcore up; maybe one of our resident experts can advice.
I started out on this journey with exact problem you faced; I couldn't change High Performance mode from optimised to manual. I still haven't found a solution unless I enable DOT. I've tried bios b5, b6.1 and now trying b6.0, without success. O/S fails to load. Did you say b3 allowed you do to that and increase fsb in bios or was it change of memory? I'm thinking my expensive ram is not very flexible and doesn't suit the nforce 2 chipset. At moment with bios b60, high performance manual, memory to manual (2-2-2-11) and DOT enabled-private I passed memtest overnight. I'll try prime95 tonight if I have no issues tday.
Dave

K7N2 Delta2-FSR Won't Boot

Hi everyone,
I was in my bios cell settings and I believe I accidently changed my FSB setting from 166 to 200 with my multiplier set at 12.
My motherboard is a K7N2 Delta2-FSR (601-6570e-020) with a AMD Sempron 2800 and 2x512mb RAM. The system was totally fine before hand and now it won't boot at all. I can switch on the system and all the drives power up but my screen stays black with the amber light on and no post beeping. I have tried removing all my memory modules and when i boot with no memory, i get the long continuous beeps which signal "No Memory Present". When i install 1 module it doesn't post and doesn't beep at all.
I have tried unplugging my power cable from the PSU and tried resetting the clear CMOS Jumper to pins 2-3 for 15-30 seconds and then returning the jumper to pins 1-2. I have then plugged the power cable back into my PSU and then powered on the system but still i get the black screen. I have read on these forums about a "Safe Mode" jumper known as "J10" but my motherboard doesn't have this jumper. It only has the JBAT1 jumper.
Are their any other methods to reset my FSB to default or to reset the bios safely?
Will be grateful & appreciative for any help given,
Many thanks

Quote from: couttsey21 on 20-September-06, 07:43:58
All my fans are spinning, unfortauntely my motherboard didn't come with a D-Bracket so I can't test it out using that.
Any other suggestions?
well you can try without D-bracket also, just wait 5-6 seconds to ensure no boot or boot. ------> https://forum-en.msi.com/index.php?topic=96529.msg697033#msg697033

[nForce] K7N2 Delta2 Platinum w/Version B.5 BIOS, trouble with post and XP install.

I have
K7N2 Delta2 Platinum
MS-6570E Version 1.0 motherboard
AMD Sempron 2600+
Elixir 500MB PC-3200 DDR (3 sticks, total 1.5GB)
eVga Nvidia MX4000 64MB AGP card
Maxtor ATA-100 PCI controller
I pulled everything else out of the box. I've tried the B.3, B.4, and B.5 BIOS and set everything to Optimized Defaults. I created a striped RAID Array of 4 WD 80GB drives on the primary and secondary onboard controller. The CD is on the Maxtor controller.
There are some problems I can't figure out.
1) The mobo identifies the CPU as Athlon XP 1100
2) The POST hangs just before seeking the IDE drives. I have to hit a key for it to continue.
3) The LED's on the D bracket have the top right light dark until the key is hit. Something to do with initializing the floppy controller.
4) The XP install fails to a blue screen just after hitting the F8 key to accept the license. The code is 0x0000007B.
Can someone tell me what these issues have to do with each other and how I can correct them?

Quote from: dmichael34 on 17-September-05, 22:42:56
The Maxtor controller was removed when you originally suggested to do so. The add on controller is an SIL 680 RAID.
I will try reseating the processor next.
I can also attempt a boot through POST without the array, as this shouldn't affect the boot process.
I did notice that the ctrl-alt-del on the LEFT side of the keyboard doesn't work.
However, the ctrl-alt-del on the RIGHT side of the keyboard does work.
Maybe I've been looking for a serious problem and overlooking the obvious.
I do not see how the CPU temp would cause a pause at boot until "any key" is hit... it sounds more to me like the system has paused to either look for a device or boot a BIOS on a device card.
If I am not mistaken, you are using a RAID card to boot windows? Is this correct?
If that is true it is possible the boot sequence is not set correctly in the BIOS such as "BOOT OTHER DEVICE" ( I cannot remember the exact term in the BIOS)
I am not sure about that but you could try changing the boot sequence so your RAID card is above "HARD DISK" on the list

[nForce] has somebody MSI K7N2 Delta2-FSR + barton mobile

I wanted to know if there is a possibility of changing cpu ratio because msi kt4av did't see this cpu as mobile. on epox 8rda3+,8rda3+pro, and abit everything is ok. Has there somebody such mainboard with this cpu? Does mainboard seethis cpu correctly? And does somebody know if how to change the cpu ratio in barton mobile's bios.i wanna buy MSI K7N2 Delta2-FSR

Frequency/Voltage Control in BIOS
"CPU FSB Clock"
"CPU Ratio" (multiplier)
that is from KT4AV manual
mobile CPUs aren't properly identified on most boards, but that is merely a "cosmetic touch"

[nForce] K7N2 Delta2-FSR and AX-7 Heatsink

Similar Messages

Maybe you are looking for