[nForce] new nforce 1 & 2 drivers remix (unofficial)

hey guys, try this new nforce 1 & 2 chipset drivers. its a new set, i ve already tried myself and it even better than the old 6.53 remix drivers from guru3d in my opinion
here is the link http://www.planetnvidia.com/modules.php?name=Downloads&d_op=viewdownload&cid=4
give it a try!!!   

Been running a day  now, no problems with my resurected K7N2-ILSR Delta and using the Nvidia IDE drivers.
Fresh loadup Win 2000 Pro.

Similar Messages

  • NForce 4.27 drivers + SB Audigy 2 ZS Platimun = Windows XP not booting!

    Hi folks,
    I know that I'm not using my MSI K7N2 Delta in my main rig anymore, but I've gotten good help here in the past (you guys rock!), and I *do* have the MSI GeForce 6800GT in my config so I was hoping that you folks might be able to give me some insights.
    I have a system with the following components:
    DFI Ultra Infinity nForce2 Ultra motherboard (latest BIOS)
    2 x 512MB OCZ PC4200
    Mobile Athlon 2500+
    MSI GeForce 6800GT (Forceware 61.77)
    PCI Slot 3 Intel 10/100+ PCI NIC
    PCI Slot 4 (not shared) - SB Audigy 2 ZS Platinum - Assigned IRQ4 manually
    All on-board peripherals disabled except for FDC, IDE1, USB
    After much gnashing of teeth, (and several reinstalls of Windows XP) I narrowed it down to a problem between the nForce drivers and the Audigy 2 ZS drivers.
    I'll tell you what happens:
    When I install Windows XP, everything is great. Everything loads up just fine. I can get Windows installed without a hitch. I then upgrade to SP2. No problems. I then try installing the nForce UDP 4.27 and it works with no issues. I can even install the drivers for my GeForce card and, again, no problems at all.
    However, if I then install the driver software for the Audigy 2 ZS Platinum, the system will no longer boot into Windows XP!
    If I do the reverse, as in install the Audigy 2 ZS Platinum drivers FIRST, the system is fine until I try installing the nForce UDP 4.27, then the same thing happens.
    There is little recourse but to reinstall Windows (I'm not doing an ASR if I can avoid it as they're messy) in either case because I can't even get into SM w/ CP.
    When Safe Mode shows the drivers loading the system hangs at MUP.SYS then never continues.
    I Googled the problem and I found a bunch of suggestions about how to avoid conflicts with the Audigy cards, and I assigned Slot 4 to IRQ4 and no other device is conflict/sharing with it.
    On a note: I actually DID manage to get the Audigy and nForce drivers to work properly to allow me a clean reboot, but that was before I realized that I'd forgotten to power up the Live! Drive. When I shut down and powered up the Live! Drive, the system wanked on startup. Even removing the Audigy 2 card did not allow Windows XP to boot up after this happened.
    I guess my questions are:
    1) Has anyone ever run into this before?
    2) Does this sound like a problem with SP2 acting wanky? Should I just try installing the nForce/Audigy software on the base Windows XP and see what happens?
    3) Do I NEED to install the nForce 4.27 drivers, or is there another version that you can recommend that might be more friendly, or do I even need to install them at all? What parts of the nForce driver do I absolutely need to install if I must do so?
    PLEASE NOTE: This setup worked fine with a SB Live! Platinum 5.1 in the same slot prior to me upgrading to the SB Audigy 2 ZS Platinum (and the old sound card worked great on my old K7N2 delta). However, I was also not trying to run SP2....
    Any help that any of you gurus out there can give me would really be appreciated. I'm at the end of my rope here.
    Thanks

    Quote
    Originally posted by Tango
    APIC on or off?
    When u install the nforce drivers if you havent already done so DO NOT install the ide drivers and see what happens.
    I have APIC on, as well as ACPI. I have also manually assigned IRQ4 to the slot with the Audigy card and it's not shared. I disabled the onboard serial ports, parallel port, firewire, NIC and audio.
    It is worthwhile to note that when I installed the Audigy 2 ZS Platinum drivers FIRST, that all devices in the system functioned properly and without problems. It wasn't until I upgraded the system drivers for the nForce components that it refused to boot. This would seem to indicate a conflict between these sets of drivers, and not an IRQ problem or hardware resource conflict.
    Could it maybe be SP2 doing it? Should I try installing as Wonkanoby suggested below with no service packs or SP1a?
    Quote
    Originally posted by Wonkanoby
    put the drivers in a folder and unrar them
    for starters you can delete the 2x audio folders if not using them
    you have turned the onboard sound of in the bios
    the new installer will also let you install them one at a time
    so you can try and find what ones doing it
    http://forums.pcper.com/forumdisplay.php?f=66
    http://www.nforcershq.com/forum/viewforum.php?f=64
    would be worth a read and an ask as wellQuote
    Thanks Wonkanoby. I appreciate the links, and yes, I'll try to install the nForce drivers one by one. I'll create Restore Points for each one and figure out where it's dying. Someone else on another forum suggested disabling MUP.SYS as it seems to be hanging there, but it could just coincedentally be the last item loading BEFORE it blows up.
    Thanks for everything :D

  • NForce DOS ndis drivers

    Hi,
    I was searching the net to find registry settings for the nForce onboard lan drivers, so far no luck....
    But I did stumble on these:
    DOS NDIS DRIVERS!!!!!
    Download here.
    Or here (mirror).
    I presume they work on all nForce boards.
    There is a description on how to use them.
    Have fun with them.

    i am upgraded my mobo, this is my first time installing the mobo, i'm upgrading from a previous mobo thats why i installed a fresh copy of XP pro.  I haven't checked the bios to see if its enabled, I didn't think there would be a bios setting that wouldn't allow my ethernet controller to function to work properly.

  • New nVidia 6.70 drivers

    Recently i got nVidia nForce 6.53 drivers on my computer installed, they are working well. I would like to install the latest nForce 6.70 from nVidia  and i am not sure how to do it. Do i have to uninstall the old ones first ?
    Thanks in advance.

    1. Yul is not using RAID;
    2. Of course Windows will not see the RAID arrays after uninstalling the drivers ... installing the new drivers will make the array come back again, though - so I do not think that you actually killed your system (the arrays were just temporarily out-of-sight ). I have done this numerous times before I switched to a Promise card;
    3. If the OS is on the array, then of course the situation is a bit more complex, but even then you will not kill your system right away;
    4. it is good advice and generally accepted to remove remainders of old (Nvidia-) drivers, before installing new ones
    Hans

  • NEW VIA Chipset 4in1 Drivers for KT4AV BAD

    Ok heres the problem. I have a KT4AV-L motherboard and I wanted to update the VIA Chipset 4in1 Drivers. While I was installing it and when it reached 100%, the screen went black and wouldn't boot back up. I had to hit the restart button to reboot Windows again. Doesn't anyone also have this problem with the new VIA Chipset 4in1 Drivers V4.51 on the KT4AV motherboard?

    I haven't heard of this, but I know if not installing under Safe Mode the driver install often hang at the last percent.

  • New Sandy Bridge GPU Drivers?

    I saw in an article (and of course now can't find) that Intel had released new Sandy Bridge graphics drivers.  Has anyone seen or tried these, and what did you find out?
    Edit: Found it --- http://news.cnet.com/8301-17938_105-20109037-1/sandy-bridge-driver-update-boosts-windows-game-perfor...
    W520 | FHD | i7-2720QM | 8GB RAM | nVidia Quadro 1000M | Intel 510 120GB SSD | Seagate 7200rpm 500GB HDD
    T510 | 1366x768 | [email protected] | 8GB RAM | nVidia NVS 3100M | Seagate 7200rpm 500GB HDD
    T61p | 1920x1200 | [email protected] | 4gb RAM | nVidia Quadro FX 570M | Hitachi 320GB HDD | (broken frame, now a file server)
    Solved!
    Go to Solution.

    I downloaded the zip file version of the driver then followed the manual installation instruction in the readme file to get it installed.I had a problem using the EXE version because I am always prompted with this message:
    "The driver being installed is not validated for this computer. Please obtain the appropriate driver from the computer manufacturer. Setup will exit."
    whenever I launch the EXE installer.
    Graphics operation feels snappier but I had a problem with color profiles being unstable in Optimus mode. The screen randomly turns bluish or redish despite being calibrated by the color sensor. The WEI graphics score in Intel-only mode is 6.4 as shown in this picture
    http://www.thaithinkpad.com/forum/index.php?action=dlattach;topic=17873.0;attach=31031;image
    Twitter @thitiv | Work | ThinkPad W520 (4270-CTO) Core i7-2960XM 2.7/3.7 GHz | 16GB Kingston HyperX PnP DDR3-1866
    2 x 256GB Crucial M4 & C300 SSDs | Intel Centrino Ultimate-N 6300 | Ericsson F5521gw WWAN | Ultrabay Blu-ray Burner
    NVIDIA Quadro 2000M | 15.6" FHD 1920x1080 | ThinkPad Battery 55++ (9-cell) & Battery 27++ (9-cell slice)

  • NVIDIA nForce 6.14 Drivers

    There are new nForce drivers available, version 6.14, consider this as beta and use at your own risk! Windows XP users must install service pack 1, at a minimum, without you cant use USB2.0. Installation of DirectX 9.0 or higher is required in order to use NVMixer.
    What's New?
    http://www.maksys.biz/comcentral/showindex.php?p=293#post293

    I would like to add that I upgraded to the new Nvidia drivers and it decreased my perfromance from what I had.
    RA 7.9 from 8.0
    CPU - 4% - unchanged
    Avg speed - 101.5 from 112.8
    Burst - 237.3 from 236 (only increase)
    The graph wasnt as straight. Many more peaks and valleys from a very straight graphing of the performance.

  • NVidia nForce 6.67 drivers WHQL

    NForce chipset drivers 6.67 WHQL

    Quote from: crjackson on 29-September-05, 03:50:20
    If you're all through playing hide-and-go-greek, perhaps someone can tell us how well the drivers are working...
    And perhaps I can learn to put all the words in my original post.

  • New NVidia 3.13 drivers now XP Pro Hangs

    I installed the new drivers and now my machine won't boot. It gets to the XP PRO startup screen And Hangs. Anybody have a fix?

    Quote
    Originally posted by Roger Wilco
    Quote
    Originally posted by Dancer
    I installed the new drivers and now my machine won't boot. It gets to the XP PRO startup screen And Hangs. Anybody have a fix?
    See if this works:
    Press F8 repeatedly as your machine boots up, until it comes to a selection screen.
    Choose "Start my computer with last known good configuration" (or something to that effect).
    This should roll back the nForce drivers, and windows should boot normally. One other thing, I'll assume you installed the SW IDE driver? (it asks you during the nForce setup, and you have to choose yes or no).
      If you did install the SW IDE driver, when you get back into windows, reinstall the nForce drivers, but this time choose NO! when it asks to install the SW IDE driver.
    Hope that helps, let me know!
    Roger
    Great Job Roger, that did the trick!
    Thanks so much  

  • New VIA 4in 1 drivers

    I used auto update to download and install the new 4.51 VIA 4in1 drivers and had nothing but issues running them. The system would do a reboot every 30 minutes or so ....I went back to the 4.49 and it all works fine...anyone else have any issues????

    Hi Husker_Faithfull
    I have been running the 4in1 version 4.51 Pro "BETA" package with no issues.
    The alternate site that VIA has listed to get this PRO version is:
    http://www.hardtecs4u.com/files/via/     It's a german site or the direct d/l link is:
    http://www.3dcht4u.de/ht4u/t13fgendz/via/4in1451Pro.zip
    Remember that this version is not MS HQL Certified but others that have installed it that have the same VIA chipsets that we do ...are reporting that it improved game playing frame rates and was a stable build for them.....
    Cheers
    Saphire

  • New Hard Drive and drivers are not installing

    I recently got a new hard drive and now I cannot install drivers from the recovery disk.
    mobile intel 4 series express chipset family
    nuvoton CIR Transceiver
    nuvoton HID CIR Receiver
    Atheros AR8131 PCI-E Gigabit Ethernet Controller (NDIS 6.20)
    Realtek RTL8191SE Wireless LAN 802.11n PCI-E NIC
    INtel High definition Audion HDMI
    I receive device status for each one of:
    Windows cannot verify the digital signature for the drivers required for this device. A recent hardware or software change might have installed a file that is signed incorrectly or damaged or that might be malicious software from an unknown source (code 52)
    HELP

    Which computer? There is a label on the bottom.
    Exactly which hard drive is it? Give us the specific model so we can look it up.
    Windows cannot verify the digital signature for the drivers required for this device.
    If you have restored the hard disk to its original out-of-the-box contents using Toshiba recovery media, that probably means you restored to a drive with the new advanced-format technology.
    Try installing this driver.
       Intel Rapid Storage Technology
    More information in this thread.
       After Restoring to New Hard Disk, No Windows Update - a Fix
    Please let us know how it goes.
    -Jerry

  • New 32bit audigy2 zs drivers today (may 12

    there are new non beta drivers out today for the audigy2 zs line.
    does anyone know why/if...
    . they don't include the EAX 4.0 ADVANCED HD Driver Update (SBA2_EAX4DRV_0303.exe Released on 9 Nov 2003), thats still a seperate download...
    2. they are "newer" than the beta driver released on april 5th? i know they are newer being that they were just released today, but are they the beta's updated to non beta status or an updated older driver?

    so this new package (may 2th 2005) contains the july 29th 2004 update that was a repack of the march 29th 2004 and november 9th 2003 updates, but lists as a requirement the november 9th 2003 update?
    Creative Sound Blaster Audigy2 and Audigy2 ZS Driver Update .84.55
    SBA2-WEBUP-W9-LB
    This web download combines the fixes and enhancements from previous driver updates for your Creative Sound Blaster Audigy?2 and Audigy?2 ZS series internal audio device.
    Fixes:
    SBA2_PCWDRV_LB__84_55.exe (Released on 9 Dec 04)
    * Enables Digital Rights Management support
    EAX4DRV_AUDIGY2__84_50.exe (Released on 29 Jul 2004)
    * Resolves the issue of the computer not responding when the phone cable is disconnected from the modem while an Internet connection is being established
    SBA2_WEBUP_PCWDRV_-84-40.exe (Released on 29 Mar 2004)
    * Ensures THX? Setup Console does not reset to default values when launched
    * Removes noise and distortion when using THX Setup Console
    * Synchronizes settings between EAX? ADVANCED HD? and Creative Graphic Equalizer
    * Enables MIDI device name display in both Windows? Multimedia Device and SoundFont? Bank Manager
    * Enables activation of imported EAX effect presets
    * Resolves the audio mute issue when certain EAX effect presets are activated
    * Restores system functionality when searching backwards or forwards while playing DTS?-encoded audio CDs on an external DVD player, with audio routed through your audio device
    * Enhances the performance of PC games that use nati've OpenAL API extensions
    Requirements:
    * Microsoft? Windows? XP Service Pack 2 (SP2) or Windows 2000 Service Pack 4 (SP4)
    * Creative Sound Blaster Audigy 2 or Audigy 2 ZS series internal audio device
    * EAX 4.0 ADVANCED HD Driver Update (SBA2_EAX4DRV_0303.exe Released on 9 Nov 2003) for Sound Blaster Audigy 2 and Audigy 2 ZS installed
    Note:
    * Do not install this update for Sound Blaster Audigy 2 Value, external USB Sound Blaster? or PCMCIA Sound Blaster audio devices.
    i was confused before, but now i'm MORE confused...

  • New Official Nforce4 Chipset Drivers

    http://www.warp2search.net/modules.php?name=News&file=article&sid=29035
    Manolis aka Markoul

    The only thing newer in these over the Nvidia 6.53 drivers is the IDE driver. Other drivers in the package are, in fact, older than those found in the NVidia 6.53 standalone package.

  • XP new, can't install drivers for vidcard G4ti4400

    I just installed Windows XP Pro, then SP1, on an ASUS P4S533 motherboard.  I have my graphics card (G4 Ti4400) showing as "Unknown VGA controller" under Device Manager. I can't update the drivers by any means without the monitor going black (I can hear sounds in the background if I hit esc though). After a hard re-boot, the monitor goes black when Windows tries to load.
    Could this be a power problem?
    I'm not sure where I should look up the specs on my power supply like in some of the other posts I've read, but pcprobe shows:
    +12V  12.35
    +5V    5.187
    +3.3V 3.168
    VCore 1.6
    I tried to update the drivers before and after the SP1 update.  I didn't have this problem with the card on the previous system (XP too) that I took it from, so I'm assuming that there's a problem with the motherboard or the drivers.
    Help appreciated. Thank you,
    Chris
    p.s. I have the latest bios too.

    Hi, thank you for replying.  I have some news.
    First, the specs are as follows:
    300W
    +3.3V    20A
    +5V       25A
    +12V     10A
    +5VSB   2A
    -5V        0.5A
    -12V      0.8A
    The other news is that I tried setting AGP 4x in the BIOS down to 2x and now the drivers will go through.  Two things about this: 4x was fine for this video card on my previous computer; and I thought a G4ti4400 would be AGP 4x capable.
    If it uses more power when it's in 4x, then these problems would make sense as a psu problem, right?
    Thanks,
    Chris
    Quote
    Originally posted by wonkanoby
    combined watts and amps of psu label 3.3 and 5 v
    http://www.pcreviewspot.com/reviews/misc/coolmax470/wattages.jpg

  • New Audio and IDE drivers

    Having probs installing these drivers. The .exe runs upto the point where the nVidia splash screen comes up and the progress bar goes all the way to the end and then the program vanishes, with out installing the new drivers.
    Yes I did stop my anti-virus running, and I even tried doing it in safe mode!
    Any ideas how I can install the drivers.
    Thanks
    P.S. XP Pro, K7N2 Delta ISLR, 1Gb RAM, XP2800+ Barton, Latest BIOS.

    Hi,
    Did you Uninstall other drivers first - if not do so, use a program like "Driver Cleaner" to remove the bits that are left (after uninstall).
    Link: http://www.majorgeeks.com/download3214.html
    Axel  

Maybe you are looking for