NForce2 and New Athlons and audio drive bay

Read it here
BIM

This was interesting:
Quote
We believe that this will be the best performer in the neighborhood for a while and that’s why AMD was using pre-production Nforce 2 boards from Asus to show the power of their new FSB 333 processors.
We think that Nvidia learned a lot from the original Nforce and that the same mistakes will not be repeated and that the stability of Nforce 2 will be on higher level than original Nforce with of course, more mature drivers.
Motherboards should be available in middle October at the earliest.
Take Care,
Richard

Similar Messages

HP Pavilion g6-1201tx Notebook PC video and audio driver for graphics card

i want HP Pavilion g6-1201tx Notebook PC video and audio driver for graphics card (Windows 7)

Hi:
Below is the link to the support and driver page for your notebook.
http://h10025.www1.hp.com/ewfrf/wc/product?cc=us&dlc=en&docname=c03061225&lc=en&product=5163244&quer...
Your model uses the AMD graphics driver only. Don't install the Intel one.

8.1 Disabled number keys and audio driver

I have a Lenovo G780 lap top that I just bought about a year in a half ago. I purchased it from Lenovo with Windows 8.0. When I updated to 8.1 recently, it wiped out the use of several of my numeric keys on both the number keys at the top across on my keyboard and also on my numeric keypad. The update also wiped out my Dolby Audio Driver. Does anyone know how to resolve this? I already had a Microsoft tech dial into my laptop remotely and he was unable to resolve it and referred me to Lenovo. Ugh. BTW - the only way I am able to type several the the different numbers is by connecting an external keyboard to my lap top. These are the numbers that work using the number keys going across the top of my laptop keyboard: 123456 These are the numbers that work using the laptop number key pad on the right of my laptop keyboard: 13456789 In both cases, the zero key is not working.

Punkinero,
For the “unable to start the Dolby audio driver”, you can use the following knowledgebase article to correct it:
http://support.lenovo.com/en/documents/ht100126
For the non functioning numeric keys, try doing this:
- Go to the Control Panel, Ease of Access Center, Set Up Mouse Keys. At the bottom under Other Settings: Use mouse keys when NUM LOCK is: Make sure OFF is selected.
I hope this helps!
Cheers, Erich_Lenovo

Zoom H4n and audio driver error -2

I have a newish Intel Macbook with GB 09, and a Zoom H4n recorder that I have been using as an USB input device into GB with no problems.
However, GB no longer recognizes the H4n. The drill is to have GB open and connect the H4n to a USB port. The computer detects the device and asks if I want to use it as an input device. I say yes, and then this message appears:
"error code -2 was returned by the audio driver"
Is this a problem in the Mac? Do I need to reinstall something?

Hi there,
Did you by any chance ever find a solution to your problem with the H4n?? I'm having exactly the same problem. I think it might have something to do with a preference file. I didn't disconnect the zoom properly before unplugging it, and since then I am having the same problems as you??? Very frustrating....
Thanks.

Software Modem and Audio driver errors!!

I currently have a Toshbia Satellite A215 S7413. Running on Windows Vista. Recently when downloading intunes, I incurred Errors in my Software Modem and Realtek Audio within my device manager. Unable to update drivers. i currently have no sound. I need a detailed description on how to repairs these. Message reads "Windows cannot read the device driver for this hardware. The driver may be missing or corrupted. (code 39). Any suggestions?

Satellite A215-S7413
You have tried reinstalling this driver?
Realtek Audio Driver for Windows Vista
-Jerry

DV7-4060si beats and audio driver issue

Whenever I try and change the EQ in the Beats application, or the bass/treble in the tone controls, nothings. I click save, then when i go back to it, its reverted to default.
Also, when I try update my audio driver, I reboot and suddenly theres no sound. This is fixed by reinstalling the original drivers.
Help?

Try and install driver from here and check ftp://ftp.hp.com/pub/softpaq/sp50501-51000/sp50642.exe.
Although I am an HP employee, I am speaking for myself and not for HP.
Make it easier for other people to find solutions, by marking my answer with 'Accept as Solution', if it solves your problem.
Click on the BLUE KUDOS button on the left to say "Thanks"

Nforce2 and IDE driver bluescreen

I have a K7n2g Nforce2-ISLR board and when I run the latest system driver update it blue screens on the IDE driver update. To confirm this I installed each driver one by one until I found the one causing the blue screen.
System config is a follows
1GB RAM
Radeon 800 pro 256MB
Onboard Audio w/realtek drivers
SATA Drives
TDK DVD writer
Floppy
Maxtor USB external 250GB Drive

i dont recommend the ide drivers.
they fail for alot of people including me so its better to stick to microsoft drivers.
get the unified driver package from http://www.nvidia.com instead.
dont flash bios in windows with live update.
seen alot of badflash when doing that.

G560 and audio driver with XP

Iv'e upgraded my G560 to XP. I get a blue screen sometimes, it mentions a driver problem, unfortunatly I did note not down the exact error mesage, but it was very generic, so I do not know what device's drive coudl cause this.
I see 2 oddities in Device manager:
Under "Monitor", "Thinkpad Display 1366x768" is listed twice.
Shouldn't there be only one monitor listed? Can I disable one?
Under "Sound, video and game controllers", I see 2 audio related drivers listed:
Conexant SmartAudio HD
And
Intel(R) Display Audio
Do I need both drivers?
Thanks for any help,
Lukas

Quote from: flobelix on 14-January-13, 02:45:17
If you want help it's bad idea to introduce yourself with bashing posts. Please stop that MSI bashing.
The Realtek driver works problem must be elsewhere. What means it doesn't work? No sound on front or rear panel connectors? Are sure to have used XP64 and not XP32 drivers? Does devbice manager of windows show the device unknown or with an exclamation mark?
I only use rear panel because of my 5.1 setup, and the speaker works perfectly in windows 8 x64 and ubuntu
My machine use triple boot OS'es >>> xp x64, win 8 x64, and ubuntu
And yes, there are several exclamation marks in device manager, and the realtek driver doesn't work at all, I installed all the other xp x64 driver from the product support section
I have erased the xp x64 partition, and I tried to install the realtek driver in xp x64 virtual machine, and it even shows the same symptoms, either failed install or successfull install with no sound at all, and sound section of the control panel, said "no audio device"
This is the first time I encountered so many problem with one mobo during years of my computer hobby
Yes, I want help, but I don't count much on it
MSI may ban me, MSI is very much welcome to take any further actions on me
Since this isnt the only forum, where I posted it
Talking about responsibility and morality, being obnoxius in computer industry

Install pc sound and Audio

hi i actually lost ma sound and Audio drive please help me
thanks

Hi,
Check Cheryl and Rakhmad XP general guide which You may find here.
In first part You will find answer on Your question.
** Say thanks by clicking the "Thumb up" icon which is on the left. **
** Make it easier for other people to find solutions, by marking my answer with "Accept as Solution" if it solves your issue. **

Sound and audio device

hey i just format my Compaq C707TU laptop and its sound and audio driver not working, please suggest me for proper driver to install in my laptop.

Hi,
For XP:
Before Conexant Universal Audio Architecture (UAA) here
Conexant High Definition Audio Drivers here
This will create a swsetup folder in c drive ("C:\swsetup\sp34200")
Installing Audio drivers may result in an error. But continue with the following steps to get the audio driver installed correctly.
Open the Device Manager:
1. Click on Start and select Run. Now type devmgmt.msc and press enter.
2. Right click on "Audio device on High Definition Audio Bus" and click Update driver.
3. Select "Install from a list or specific location"
4. Click Next. Then select "Don't search, I will choose the driver to install"
5. Click Next and then select "Sound, video and game controller" from the list.
6. Click Next and then click Have Disk.
7. Click Browse C:\swsetup\sp34200 folder and select the .inf (wis30b2a) file and click open and Continue with the onscreen instructions.
Similarly install Modem Drivers:
Conexant HDAUDIO Soft Data Fax Modem with SmartCP here
1.Right click on "Modem device on High Definition Audio Bus" and click Update driver.
2. Select "Install from a list or specific location"
3. Click Next. Then select "Don't search, I will choose the driver to install"
4. Click Next and then select "Modem" from the list.
5. Click Next and then click Have Disk.
6. Click Browse C:\swsetup\sp33890 folder and select the .inf (wis30b2b) file and click open and Continue with the onscreen instructions.
For Vista:
Conexant High-Definition Audio here
Conexant HDAUDIO Soft Data Fax Modem with SmartCP here
** Say thanks by clicking the "Thumb up" icon which is on the left. **
** Make it easier for other people to find solutions, by marking my answer with "Accept as Solution" if it solves your issue. **

Hard drive bays 3&4 painfully slow performance (3mb/sec) under Windows XP

I have the 2009 Mac Pro and experiencing ridiculously slow throughput of hard drives in bays 3&4. The drives are brand new Western Digital 1TB and Seagate 1.5TB, formatted NTFS. The drives work blazing fast when installed in Bay 2 (~90mb/sec!) but slow down to a crawl when installed in bays 3&4 (3mb/sec!). I used HDTach to run some low level benchmarks to make sure it's not an OS issue, and both the average read and burst speeds were 3.0 MB/sec. Under Leopard, the drives perform great. All of this leads me to believe this is some sort of Boot Camp driver issue that affects only the third and fourth drive bays/SATA ports on the new Mac Pros.
Any help is much appreciated!

Run WD Diagnostic on the drives and do a full zero and extended test on them.
I've had two WDs that had really bad I/O graph patterns showing jumps from 95MB/sec down to really slow and the long jaggie graph. I even put it all into a folder with charts and numbers.
XP has some real problems though with heavy small I/O patterns. Odd that it would change or show up different in different slots.
HD Tune: WDC WD7500AAKS-00RBA0 Benchmark
Transfer Rate *Minimum : 1.8 MB/sec*
Transfer Rate Maximum : 97.2 MB/sec
Transfer Rate Average : 51.3 MB/sec
Access Time : 13.7 ms
Burst Rate : 105.1 MB/sec

Hard drive bays 3&4 painfully slow performance (3mb/sec) under Bootcamp 3.0

+Since my original topic (http://discussions.apple.com/thread.jspa?threadID=1998707) has been archived and I cannot reply to it, I am reposting my new (sadly negative) findings in a new thread.+
I have the 2009 Mac Pro and experiencing ridiculously slow throughput of hard drives in bays 3&4. The drives are brand new Western Digital 1TB and Seagate 1.5TB, formatted NTFS. The drives work blazing fast when installed in Bay 2 (~90mb/sec!) but slow down to a crawl when installed in bays 3&4 (3mb/sec!). I used HDTach to run some low level benchmarks to make sure it's not an OS issue, and both the average read and burst speeds were 3.0 MB/sec. Under Leopard, the drives perform great. All of this leads me to believe this is some sort of Boot Camp driver issue that affects only the third and fourth drive bays/SATA ports on the new Mac Pros.
*Update 10/2009:*
I have upgraded my Mac Pro to Snow Leopard and installed the latest Boot Camp 3.0 drivers onto the Windows XP partition, hoping and praying that the above issue has been resolved. NO SUCH LUCK. Come on Apple, part of the reason I switched to Intel Macs was so I could have dual-OS support which is critical in my line work. Since 2006 when I bought my first iMac, then another iMac, then 2 MacBook Pros, I have never had such a horrible experience as now. Please Apple, do not shun your customer base who uses Windows!!

logicboard.
I have no trouble with bays 3&4 in Windows Vista/7 - never used XP so have no idea what problems it might pose.
How about trying Win7 next?

Setting up new MBP with SSD and optical drive and restoring from Time Capsule

Hi Everyone-
Sorry if this has been addressed before, but I couldn't find a specific answer by searching. My last macbook was stolen, but luckily I had everything backed up in my Time Capsule. I just ordered my new Macbook Pro (13"), 16GB Ram, and a 240GB SSD. I plan to install everything next week. My plan is to keep all of my apps and working files on my SSD and use my 2nd hard drive for data storage and possibly my itunes library. My question is- when setting all of this up, what would be the best way to go about doing this.
1.) Restoring my time machine backup to the original hard drive, move it to the optical drive bay, and then copy over the files that I want on the SSD (after installing the operating system) and delete them off of the origan HD.
2.) Restore my backup to the SSD (once it's installed) and then move files over to the formated original harddrive in the optical bay. My problem is that there may not be enough room on the 240GB SSD.
3.) Is there a way to do a slective restore through TM and move where I want to keep them? I think this would be the easiest.
4.) Other way that I haven't mentioned
Thanks for any help with this question.

I used setup assistant last time when I changed from a 2009 mini to a 2010 mini. It caused some file permission errors that still persist today with iPhoto. I have 2 accounts on my mini, 1 for my wife and 1 for myself, but I store all our photos and videos on the shared folder in order to avoid duplication. But when she imports pictures from her profile and I try to view them full screen, I'm unable to. I have to relaunch iPhoto and repair file permissions if I want to view them properly. I was hoping to avoid this happening again.

Hard-drive and audio interface set-up - Advice please

Hello,
Please offer me some advice if you can. I have the new 13" macbook pro 2.26Ghz with Logic Studio. I am going to get a hard-drive that has both usb and firewire 800 interfaces and need to decide whether to get a usb or firewire audio interface. The crux of my problem is in what configuration to use the devices, which will determine which audio interface I choose. E.g.
1. Firewire 800 hard-drive to record tracks onto and back-up + usb audio interface; or
2. Firewire 800 hard-drive as above + firewire 400 audio interface daisy-chained; or
3. Record onto the internal hard-drive and use a usb audio interface; or
4. Record onto the internal hard-drive and use a firewire 400 interface.
FYI, the audio interfaces I'm looking at are the E-Mu 0404 USB or Focusrite Saffire LE, both of which have had excellent reviews.
Questions to consider, please, are: Which configuration will offer the best performance and least latency? Is it worth recording onto external hard-drive (7,200) or will the internal drive (5,200) be faster/as fast? Will daisy-chaining cause a significant drop in performance? Do you have any alternative configuration suggestions? Plus any other comments you can think of.
Thank you in advance
Jamie

The good thing about #2, if the drive enclosure also has a USB 2.0 interface you have the option of using/trying that configuration as well. I know a few that get away with using USB drives for recording.
Make sure the audio drive is formatted Mac OS Extended, with Journaling OFF.
Don't trust the drive formatting as it's delivered.
pancenter-

Problem in audio driver and unable to install rescue and recovery ver 4.3 -

Dear community collegues,
I have installed original windows7 home premium in my lenovo N100 series 0768-54A model y'day. Though every thing went well, the AC97 audio driver could not be installed. Can any one provide me a solution to make the audio working in Windows7 Home Premium.
Similarly after new installation, I could not install rescue and recovery version 4.3 (windows7 compatible) in to the system, every attempt failed. Could any one provide a solution.
thanking You.
Sakthivelu V M Chennai

I am not sure which audio chipset your N100 has, so
Try this for sound:
Go to THIS web page.
Download Soundmax audio driver for Vista.
Extract the files by double clicking, and note where they
are being extracted to.
Uninstall any sound driver you have installed, reboot.
If windows says New Hardware Found, click cancel.
Go to folder where downloaded drivers were extracted,
and run Setup.
If Soudmax drivers do not work, uninstall and repeat
with the Realtek audio drivers.
I do not think Rescue/Recovery will work except for
the originally installed OS.

NForce2 and New Athlons and audio drive bay

Similar Messages

Maybe you are looking for