NI DMM Soft front panel did not detect any ni-dmm

Hello,
has anyone seen this failure? I can´t open soft front panel to setup the dmm. I tried to reinstall VISA and NI-DMM without success.
Thanks
Robert
Solved!
Go to Solution.
Attachments:
NIDMM FrontPanel_Failure.JPG ‏107 KB

Hello,
reinstalling the nidmm and visa will cause several reboots of the system. That was no solution
for me and my problem.
After starting the nidmm, the window with the information, that the 4072 won´t be found shows
a RESCAN button. By pressing the RESCAN button, the error code -1074118656 and the message,
that the device ist not recognized and this version or driver wont fit my 4072.
Should I install the only install the delivered driver or could I update to the actual version?
Delivered was Version 2.5 of NIDMM, installed on my system is the actual one from the NI homepage.
I think, I try to deinstall the NI-SW completely and install "only" the delivered SW. Hope, this will solve.
Robert
Attachments:
Error -1074118656.PNG ‏23 KB

Similar Messages

Wndows did not detect any biometric devices on this computer..

I have an HP ProBook 4540s running Windows 7 Professional w/IE11. I had to do a clean install of Windows 7 Pro and since then I cannot get my fingerprint reader to work at all. In my Control panel, under Biometric Devices, I recieve the message "Windows did not detect any biometrics devices on this computer". However, under Computer , Properties, Device Manager, Biometric Devices, the is Validity Sensors (WBF) (PID=003d).
I have tried to update, uninstall, re-install HP Simplepass, drivers, etc from the HP website, but nothing is working. Also I cannot find exactly what fingerpriint reader hardware is installed on the computer even though it is physically there as part of the original configuration.
I appreciate any assistance in resolving this issue.
Mark

Hello Mark531,
Welcome at the HP forums,
Are you searching for the following driver?
http://ftp.hp.com/pub/softpaq/sp64001-64500/sp64338.exe
Winos.
The doors of wisdom are never shut. Benjamin Franklin
We must use time wisely and forever realize that the time is always ripe to do right. Nelson Mandela

Windows did not detect any networking hardware, Windows 7, New Hard Drive

Message "Windows did not detect any networking hardware"
Satellite P505 S8980 Windows 7 Home Premium.
I replaced the Toshiba 500 GB HD with 500 GB Seagate.
Device Manager icon for any device with yellow exclamation mark,
Click on "Update Driver". Lan eNet details as follows:
Antheo - R8132 PCI-E Fast Ethernet Controller (NDIS 6.20)
Browse to the folder where the setup program has the driver...
Message: "The best driver software is already installed."
(But the yellow exclamation mark still harasses me.)
--- Go to "Setup new connection" ---
"Choose a connection option"
Click on "Connect to the Internet"
Response: "Windows did not detect networking hardware"
As near as I can tell, that translates from error 0x8E5E0247
I have this same error on other yellow exclamation marks respective of what kind of device it is.
=> To test my sanity, I put the old hard drive (same size) back in and except for the impact of slowness due to error retries, everything works okay.
Note:
Same issue (hardware not detected) for Video adapter and Audio.
I bought new USB Wireless adapter to test, and the driver installed but not activated because "not digitally signed", and that same issue fits all the above hardware. I down loaded them from Toshiba, and they are confirmed installed, but not accepted with digitally signed. I have uninstalled and reinstalled with same results.
Solved!
Go to Solution.

I'm discovering I am not as well as I thought... running on the AF hard drive which was built with a copy drive from old format drive which was the product of system recovery disc set.
Review for context: Advanced Function HDD
Scenario that exposes harm caused by cloning data from 4K blocks drive to 512 bytes blocked drive (AF)
Toshiba supplied Windows-7 System Restore Discs: to factory state
Then I built the Windows-7 Repair Disc... used later.
Hard drive was replaced when it caused SMART warning at every system boot.
Acronis was only utility that quickly detected problem (3 sectors had permanent read errors.) Active@Disk Image and Power Quest Drive Image (Ghost) did not detect the issue.
I tried Seagate 500 GB and Western digital 500 GB HDD drives as copy target.
That new drive would not boot: "Required source not found"
Booted My newly created Windows-7 repair disc, and used to to fix startup.
See images.
That worked and then the ST9500423AS disc booted.
Now... next day I discovered Window Update is not working.
I get message:
Windows Update cannot currently check for updates, because the service is not running. You need to restart your computer.
I ran Microsoft Fixit for updates. It says it fixed two items.
I still have the problem.
The service shows "started"
Control Panel/ ACTION Center/ Maintenance/ Check for Updates
"No action needed"
"Windows Update does not require any action"
I checked Update History...
... It is empty, else window is vacant... blank.
Soooo..... for a sanity check, I swap out hard drive; go back to the old format (which is the one I copied).
It works! 7 updates to install, including SP1... but I did NOT install them.
Switch back to the AF drive... Update doesn't work. I am broke again.
Is this another strange problem caused by the Advance Format issue?
What to do?
By the way... I did install an Intel storage Matrix driver update, but I do not have RAID chip, so that driver is not for me... unless I missed out on something.
Carl

Windows did not detect any networking hardware iMac 27' 2013 model

Installed windows 7 using bootcamp now when I go to connect to a network it says windows did not detect any networking hardware

Did you install the windows drivers as well?

I just tranfer all my photo from my Mac though itune to my iPhone so I can setup Mac back to factory setting after doing I try to put my photo vac to my Mac I photo did not detect any of the photo that I had tranfer from itune it only detectPLAESE HELP!

I just tranfer all my photo from my Mac from itune to my Iphone so I can setup Mac back to factory setting after I don't with that, I try to put my photo back to my Mac and Iphoto did not detect any of the photo that I had tranfer from itune it only detect the one rhat i took with the Iphone PLAESE HELP!!!!!!

Hello Partii,
It sounds like you may use a POP account for your email. With a POP account, email applications like Mail and Outlook can remove emails from the server, so when another device tries to check the server for new emails, it doesn't see any.
You may need to adjust settings in Outlook so that the emails are not removed from the server when downloaded. I found an article with more information:
When using a POP email account with multiple devices, email messages may only appear on the first device that receives them. This occurs when an email client is configured to automatically remove email from the server once an email client has received it. You can configure your email client (or clients) either to keep a copy of the email on the server, remove it after a certain number of days have passed, or keep it until you move it from your Inbox.
I recommend reviewing the full article for steps on adjusting these settings; you can find the full article here:
Using a POP account with multiple devices
http://support.apple.com/kb/HT3228
Thank you for using Apple Support Communities.
Best,
Sheila M.

M2N78-LA Motherboard BIOS did not detect any Hard Drive

Hi,
I have M2N78-LA Motherboard and the BIOS did not detect ANY hard drive
I tried
1- Replaced the HD with another one. did not work
2- Changed the jumper of HD. did not work
3- Changed the SATA data cable and power cable. did not work.
4- Reset the BIOS by removing the battery and also by positioning the cmos jumber. did not work.
I still all time get no hard drive detected, and some time jam on Detecting storage devices ....
then after hours get no booting device.
Any Idea will be good

M2N78-LA Motherboard BIOS did not detect any Hard Drive, does anyone have an answer to this problem.

Bluetooth did not detect any Bluetooth device even iPhone please help me

I have iPhone 4 my Bluetooth did not detect any Bluetooth
Device even iPhone so I can not transfer any data to other iPhone
Please help me

That is correct.
This has never been a feature of iphone.
Sorry.
Bluetooth is supported for stereo headsets/speakers, telephone headsets/handsfree devices, some keyboards, some peer-to-peer apps from the apps store, tethering where provided by the carrier.
Other than these, it will not connect to another phone/device/computer/etc.

Wich drivers to install after ´Windows did not detect any networking hardware´

Hi there, I just reinstalled my laptop. But something went wrong. My laptop says now:Windows did not detect any networking hardware´ I found already out that I need to install drivers. But there is so much choice. Wich one do I need to install.http://h20566.www2.hp.com/hpsc/swd/public/readIndex?sp4ts.oid=5405166&swLangOid=8&swEnvOid=4059 Hope you can help me!Freek

Hi @sweetandsouther ,
Welcome to the HP Forums!
It is a terrific place to find answers and suggestions!
For you to have the best experience in the HP forum I would like to direct your attention to the HP Forums Guide Learn How to Post and More
How Do I Find My Model Number or Product Number?
I understand that Windows it not detecting any network hardware.
If you check Device Manager is it recognized?
If the card is listed is there an error on it?
If not and you are out of warranty you could try reseating the network card.
Here is a link HP Notebook PCs - Testing for Hardware Failures (Windows 7, Vista) to that may also help.
Here is a link to HP PCs - Troubleshooting your wireless network and Internet connection (Windows 7) that may also help.
Have you ran the HP Support Assistant ?
Have you tried using MS Fix It?
You may choose to contact HP support for assistance with this difficulty.
Please call our technical support at 800 474 6836. If you live outside the US/Canada Region, please click the link below to get a support number for your region.
World Wide Phone Support
Good Luck!
Sparkles1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

NI Scope Sorf Front Panel will not detect NI PXI-5122

Hello,
I am trying to use NI Scope Soft Front Panel 2.7f0 to acquire simple waveforms;
however it will not detect my NI PXI-5122. I have confirmed that the digitizer
works under MAX 4.2.1 and can see waveforms under the test panel. I have
installed NI Scope 3.3.1 on my machine and have updated the driver on the PXI
to version 3.3.1. Any ideas on what is wrong?
~Buck

It is unclear from your post whether or not the 5122 is on the same physical device as you are running the soft front panel (SFP). The SFP only works on local devices. It does not have the capability to attach to RT or remote systems (MAX does). However, if you are running Windows on your PXI controller or are using MXI to control the chassis, there is another issue.
This account is no longer active. Contact ShadesOfGray for current posts and information.

Windows did not detect any networking hardware

We have an HP Pavilion desktop, model # a6610t, using Vista OS. We have been connected to the internet wirelessly for almost 1 year and now all of the sudden it cannot find any wireless networks. We are able to successfully connect wirelessly to the Internet on other laptops and I can connect to the internet on the desktop with a cable so I know it is not the modem or router. I have also unplugged both the modem and routers - still no success.
We ran a virus scan and no treats were identified. The only thing different that we see is that we got updated to Internet Explorer 8.
Any suggestions??
This question was solved.
View Solution.

Please try to reinstall the networking drivers from recovery manager and also please inform the status of the wireless button .Does it stay orange or does it turn blue.
*Remember to mark your questions solved and click the "Kudos" star to show your thanks!

SCXI Switches not showing up in NI-Switch Soft Front Panel

Hi,
I have an SCXI 1001 chassis containing about a dozen SCXI 1160 switch modules. The first switch module is connected to a PXI-4060 DMM card in a seperate PXI chassis. MAX 4.0 was able to auto-detect the switches, and they show up under the "Devices and Interfaces" folder. However, when I run the NI-Switch Soft Front Panel application, the SCXI switches do not show up as selectable switches. Are there additional properties that need to be configured in order for the Soft Front Panel to detect the SCXI switches? Is there an online manual/guide for doing this?
Thanks in advance for any help.
VRMan

If you have the option of using a DAQmx supported device as the controller for the SCXI chassis, I would recommend changing your SCXI configuration so that your SCXI devices show up in the Soft Front Panel.
If the PXI-4060 (which is not supported under DAQmx) is the only SCXI chassis controller you have, a workaround is to use the Traditional(Old) Soft Front Panel. The Old Soft Front Panel has not been updated with switch modules since NI-SWITCH 2.4 and is not currently supported. But given that you have SCXI-1160s in your chassis, it should work for your use case.
We install the Old Soft Front Panel at Program Files\IVI\Drivers\niSwitch\OldSoftFrontPanel

Ni 5112 soft front panel

Hi:
Can you tell me how to mesuare a voltage of 5.1V on soft front panel? Because I got 5.1 volts on soft front panel, but it stop there and
it did not go back to 0V in a horizontal line.
When I used the real osciloscope, I can get that and it will return to 0 volts after 1 to 2seconds pressing the beep button.
What is wrong with it?
Let me providle my setting on soft front panel.
1Mohm, 100Mhz bandwidth, Y-AXIS 2V/div, offset 0, AC couple, CH0, , X-AXIS 10 microsecond/div, 50% reference, Trigger: edge, rising, ch0, normal, trigger level 2.5V
I am in a urgent. I appreicate if you can reply to me promply

Hi,
Attached is another diagram, maybe it will help
Attachments:
good example.doc ‏88 KB

Switch Soft Front Panel, Active Device misassigned

I have a PXI chassis with, among other modules, two PXI-2350 switches. Using the Switch Soft Front Panel, it seems the names assigned in the Active Device list ( the two 2350's in this case ) are backwards to what I expect. Is there a way to reassociate these names to the physical 2350's ?
Thanks
Solved!
Go to Solution.

Confustus,
That is an interesting issue that I have never seen before, your devices in Soft Front Panel should be linked to the devices as labeled in MAX. I was wondering, when you say "Using MAX, we can select a route that connects the power source to the DMM using "Switch 1" ( for example ), and we can see the voltage reading show up on the 4071 Soft Front Panel as expected", what exactly do you mean? If you were to select your hardware device and click test panels, the NI Switch Soft Front Panel loads. Are you saying that when selecting test panels and loading Switch Soft Front Panel from max works as expected, however opening the application outside of MAX does not work?
Or are you talking about the Test Panels that you open up within NI Switch Executive? The test panels for NI Switch Executive refer to the NI Switch Executive virtual device name, not the DAQmx device name. If you had named the NI Switch Executive Virtual device name in a similar manner, this could be part of the confusing problems that you are seeing. See images below:
NI DAQmx Test Panel Selection Brings this up.
NI Switch Executive test panel brings this up. If these device names are similar, I can see how this could be confusing.
Frank,
National Instruments
Staff Software Project Engineer

NI 5112 Scope soft front panel setting problem

Hi,
I tried to meausre a 5.1 voltage using SCOPE soft front panel. I could get 5.1 AC voltage from SCOPE soft front panel,
but it did not go back to 0 volt after 1 to 2 second in a horizontal line. Nornamlly, my 5,1V will go back to 0 volts
in my oscilloscope after 1 to 2 seconds because I am measureing a shock beep pulse waveform.
Can you tell why?
I am going to give you my setting. I was trying Y-axis 2 volt/div, AC coupe, ch 0, X-axis is 10 microsecond/div. normal mode.
Trigger: edge, rising, ch 0, trigger lever 2.5.
I am in a urgent. Coould you pls send me quickly

I'm sorry if I don't completely understand what the behavior is but if I understand you correctly, you have a signal that goes from 1 volt, peaks at 5.1, and then slowly drops to 1 volt again. That entire signal takes 1 to 2 seconds.
I am not sure if the problem you are seeing is 1. You can never get the full signal in the SFP or 2. You get the signal ok but the SFP does not wait for you to hit a button to try and acquire again.
If the question is number 1
If this is the issue it sounds like you are able to capture the 5 Volt peak, however it never goes back down to 1 volt. You mentioned that you have the X-Axis set to 10 microseconds/ div. Therefore the SFP is only acquiring an total of 100 microseconds, and if the reference is set to 50%, then you are only getting 50 microseconds of signal after the trigger, so you will not be able to acquire the 1-2 seconds it takes for your signal to drop. I would suggest increasing the number of points and slowing down the Time/Division. You should be able to change those settings a few times to actually get 2 seconds worth of signal.
2. If you want to simply hit a button and the SFP will acquire again then you need to change the mode to SGL. Then you just need to hit the run or pause button and the SFP will acquire again.
Message Edited by Evan on 09-12-2005 10:03 AM

Front panel sound not working

Front panel sound not working* Hello everyone,
I've just bought a PCI Express X-Fi Titanium. So far everything works great with my 5. sound system, but I have problems with my front panel audio.
My case only supports AC97 front panel audio, but has all individual connectors (so 7 single connectors, not one with 0 pins).
I've already tried only connecting 5 pins (the two AC97 return pins unconnected) and connecting all 7 pins. In both ways the microphone works, but sadly not the headphone output. I also tried changing the two options in the driver but that changed nothing.
I did some Google searching and found many reports where the sound itself works with an AC97 front panel on an HD soundcard, just no jack detection.
Any ideas why that isn't working for me?

! Try here for pinouts of your jacks. I have a Cooler Master case that has AC97 and INTEL HD front panel jacks, but here is the kicker. The AC97 jacks come from the front panel first and then about fi've inches from this jack is an INTEL HD jack. A few wires are changed but perhaps these will help...
http://www.intel.com/support/motherboards/desktop/sb/CS-0585.htm
Cheers,
Jerry Macguire

NI DMM Soft front panel did not detect any ni-dmm

Similar Messages

Maybe you are looking for