NI-DNET software version 1.4.2 does not show up on Labview 8.2
I am using the NI Devicenet PCI card in my system. After installing the 1.4.2 software, I had no trouble communicating with my Devicenet controller with Labview 8.0. After downloading Labview 8.2, I no longer get the devicenet vi's on the Instrument I/O pulldown menu. I can find the VI's by choosing "Select a VI" and then browsing my directories until I find the VI I want, but this is very time consuming. Also under Find Examples, therre were a few Devicenet examples under Hardware Input and Output. Those examples are no longer there.
Thanks,
Roger
Hi Roger,
NI-DNET 1.4.2 supports only LabVIEW versions that were released when NI-DNET 1.4.2 got released (LabVIEW 7.0 ... 8.0). Please use NI-DNET 1.5.1 if you need NI-DNET support for LabVIEW 8.2.
You can find it on ftp://ftp.ni.com/outgoing/NI-DNET151.exe
It will be available through the regular download channel in the next few days.
Regards,
-B2k
Similar Messages
-
PCI 6281 board does not show up in Labview as having available physical channels
Hi, I have recently changed computers from a Windows XP machine to a Windows 7 machine. I am running Labview 8.6 (I realize LabView is not officially supported for Windows 7, but most features seem to work fine). I also have a PCI - 6281 M series DAQ board. Although the drivers seem to have installed properly for this card, Labview does not see any available physical channels. The board shows up in MAX under the PXI heading, and seems to have no conflicts with VISA addressing. I am not sure if the board should be there, as is there no PXI bus in this setup. I can't see the physical channels with any NI software including DAQ assistant in the main program, or Signals Express. Any advice would be appreciated.
DAQmx is version 8.7.2. Also, I installed the card prior to the drivers, I will try removing the card and replacing it. I seem to have isolated the problem - my old computer had the card showing up under the heading NI-DAQmx devices, where on the new computer it shows up under in the PXI heading in the measurement and automation explorer. I'm still not sure how to fix it though.
-
DAQmX does not show up in Labview 8.5
History: Got sick of Vista and downgraded to XP SP2. Reinstalled Labview, Measurement Studio then DAQmX 9.4 (downloaded the latest from NI site).
Measurement Studio seems to load DAQmX tasks correctly although I am afraid to compile in case it trashes hours of work. I have no reason to trust that it won't.
Labview just does not recognize DAQmX. It doesn't show up in toolbox. Meas & Automation runs and talks to my USB-6212 so I guess that DAQ drivers must be installed and load properly. But Labview.... N/G. Is this version (DAQmX 9.4.0f1) not compatible with LV 8.5? I don't get it.
I have uninstalled DAQmX & reinstalled it with the same results (none). Please help.
Labview 8.5
Meas Studio 2008
Solved!
Go to Solution.It looks like LV 8.5 tops out DAQmx version 9.3:
NI-DAQ and LabVIEW Version Compatibility (for Windows)
steve
Help the forum when you get help. Click the "Solution?" icon on the reply that answers your
question. Give "Kudos" to replies that help. -
HT4623 How do I instal the software updates? My iphone does not show the software update
How to do I instal the software updates to my iphone?
Same as always.
Tun on your computer.
Open itunes
Connect iphone.
That's it. It will prompt you to update if one is available -
SQL Developer 2.1 EA2 does not show any procedures
With this version, the Navigation Tree does not show any procedures.
The query issued internally is:
SELECT OBJECT_NAME, OBJECT_ID,
DECODE(STATUS, 'INVALID', 'TRUE', 'FALSE') INVALID,
'TRUE' runnable,
PLSQL_DEBUG
FROM SYS.DBA_OBJECTS o, dba_plsql_object_settings s
WHERE o.OWNER = :SCHEMA
AND s.OWNER = :SCHEMA
AND s.name = o.OBJECT_NAME
AND s.TYPE = :TYPE
AND OBJECT_TYPE = :TYPE
AND SUBOBJECT_NAME IS NULL
AND OBJECT_ID NOT IN ( SELECT PURGE_OBJECT FROM RECYCLEBIN )Issue that in a worksheet to see what is failing...
K. -
I am trying to update my iphone 3GS software but itunes just says that this is the current version of itunes, it does not see the phone update - anyone know how to get the phone updated?
Mike
I have done that and it is through pressing that update, which tells me that there is anew version of iphone software, that the prompt comes telling me that this is the current itunes? -
Tried upgrading to 10.8.2. It failed the upgrade. Currently the Software version shows " System Version:
OS X 10.8.1 (12B19)" . But App store does not show 10.8.2 as an updateYou can Contact MAS here.
-
My iphone4 does not show the "software update" choice under General so how do I update my iOS?
You can alternatively connect your iPhone to iTunes on your PC and upgrade your iOS from there.
-
HP ENVY 4500 e-All-in-One Version 3.2.1 does not work on iMac 20-inch, Mid 2007. Only recognizes scanner not USB printer.
I would like to print via the USB connection instead of wireless (the wireless does work, and the scanner works via USB).
I tried connecting the printer directly (via USB) to my MacBook Pro laptop and it worked just fine.
How can I make this printer work on my iMac?
I spent 4 hours on the phone with HP and we did every combination of installation of drivers ad nausum and their bottom line is that it is a Mac problem.
Any help would be appreciated. Will be sending this printer back to Amazon if I can't make it work on the USB.
I am open to questions or suggestions
Thanks,
ChetAfter 4 hours on the phone with HP and another hour with Apple (Mavericks support) no real solution other than check everything (removed everything from Login Items, removed all HP software anywhere in the system reboot, reinstall printer) then when nothing worked for the 4500, did an OS Reinstall (boot with CMD+R).
The Mavericks support group did open an incident (# 542875311) and I will update it when I figure out how to find it on the system.
My feel is that the base problem is that somewhere between the HP-Inkjet-SW-OSX-Mavericks_v12.34.49-2 package and the Apple HP Printer software in the Library (version 2.16.1) the app for printing via the USP Port just does not get installed for the mid 2007 20 inch iMac. The scanner is recognized on the USB Port and the Printer works fine on Wi-Fi. I have too many devices to burden my home network with anothe device. Also, every time I put any HP Printer on Wi-Fi, my router (Netgear N600 WNDR3400 running 12 to 20 devices depending on who is home) gets wonky (but that's anothe story...).
Additionally, when I attach the HP Envy 4500 to my MacBook Pro (2010) it works perfect - print and scan via the USB prot and both functions show in the System Preferences - Printers and Scanners just as expected and just as the 3050 does.
Chet -
i download the recent ios for iphone 4. i connected iphone 4 to my pc and it wont connect to itunes. What is the lastest version of itunes that DOES NOT support the lastest version of ios?
Yes, due to Incomplete Software Update on your iPhone your Device is now in Recovery Mode and you cannot take a Backup now. But if you have taken a backup earlier then you can Restore that backup on your iPhone after you Reset your iPhone to Factory Settings.
-
ITunes 9.1.1 does not show up in Software Update
I am aware that iTunes 9.1.1 is availible for download at Apple's website, however for some strange reason iTunes always alerts me to upgrade to 9.1.1 but when I open Software Update it says that "Software Update doesn’t have any new software for your computer at this time." I am currently running iTunes 8.2.1 if that helps any, and I would just like to know why the newest version does not show up in my Software Update and if there is anything that can be done to fix this.
download 9.1.1 from here: http://www.apple.com/itunes/download/.
JGG -
My settings "general". Does not show a"update software " choice from the menu?
My settings "general". Does not show a"update software " choice from the menu? I cannot find what iOS software I'm currently using or what iPad I have
The option to update without the computer (Over the air) was made available with iOS 5. If your iDevice is using a version of iOS lower than 5, you will need to use iTunes on your syncing computer to perform the upgrade. Use the Apple link below as a guide for the upgrade.
http://support.apple.com/kb/HT4972
Also read the instructions from the section entitled "Update your device using iTunes" at the link below.
http://support.apple.com/kb/HT4623
Information regarding transferring purchases from your iDevice to iTunes on your syncing computer can be found at the link below.
http://support.apple.com/kb/ht1848 -
My iPad 4 does not show up on my TV screen when in AirPlay mirroring mode using WiFi. The iPad displays AirPlay set to TV with the Mirroring On (green).
My iPad IOS software is 8.2 and my Apple TV software is at 7.1. The TV displays the Apple Menu. The “Settings” does however displays the General menu allowing me to see:
Apple software: 7.1 (7003)
Apple TV: Model No. A1464, Part No. MD199B/A
Signal Strength shows 5 circles.
It does not display the iPad screen but when I use the BT Sport App I can hear the sound but there is no video. I have searched the internet for a solution to no avail. The problem first arose when the IOS was at 8.1+ but it worked correctly briefly when I updated to IOS 8.2. Can you help please?Welcome to the Apple Community.
Try the following steps, check whether things are working after each step where appropriate, before trying the next.
Check AirPlay is turned on on the Apple TV (turn it off and on if it already is)
Check that both devices are on the same network (Settings > Wifi, on the mobile device and Settings > General > Network, on the Apple TV).
Restart the Apple TV (Settings > General > Restart).
Restart the Apple TV by removing ALL the cables for 30 seconds.
Restart your router. (Also try removing it’s power cord for at least 30 seconds)
Restart your mobile device.
If you are still having problems, the following article(s) may help you.
Troubleshooting AirPlay
Troubleshooting Wi-Fi networks and connections
Recommended Wi-Fi settings
Wifi Diagnostic Software (for Mac users)
You may also find some help on this page, where I’ve collected some of the more unusual solutions to network issues.
When making adjustments to your network for better optimisation, you may find some of the points mentioned on this page helpful. -
How do i update 10.5.8 if my macbook does not show any software updates?
Upgrading to Snow Leopard
You can purchase Snow Leopard through the Apple Store: Mac OS X 10.6 Snow Leopard - Apple Store (U.S.). The price is $19.99 plus tax. You will be sent physical media by mail after placing your order.
After you install Snow Leopard you will have to download and install the Mac OS X 10.6.8 Update Combo v1.1 to update Snow Leopard to 10.6.8 and give you access to the App Store. Access to the App Store enables you to download Mountain Lion if your computer meets the requirements.
Snow Leopard General Requirements
1. Mac computer with an Intel processor
2. 1GB of memory
3. 5GB of available disk space
4. DVD drive for installation
5. Some features require a compatible Internet service provider;
fees may apply.
6. Some features require Apple’s iCloud services; fees and
terms apply.
Upgrading from Snow Leopard to Lion or Mountain Lion to Mavericks
To upgrade to Mavericks you must have Snow Leopard 10.6.8, Lion, or Mountain Lion installed. Purchase and download Mavericks (Free) from the App Store. Sign in using your Apple ID. The file is quite large, over 5 GBs, so allow some time to download. It would be preferable to use Ethernet because it is nearly four times faster than wireless.
OS X Mavericks- System Requirements
Macs that can be upgraded to OS X Mavericks
1. iMac (Mid 2007 or newer) — Model Identifier 7,1 or later
2. MacBook (Late 2008 Aluminum, or Early 2009 or newer) —
Model Identifier 5,1 or later
3. MacBook Pro (Mid/Late 2007 or newer) — Model Identifier 3,1 or later
4. MacBook Air (Late 2008 or newer) — Model Identifier 2,1 or later
5. Mac mini (Early 2009 or newer) — Model Identifier 3,1 or later
6. Mac Pro (Early 2008 or newer) — Model Identifier 3,1 or later
7. Xserve (Early 2009) — Model Identifier 3,1 or later
To find the model identifier open System Profiler in the Utilities folder. It's displayed in the panel on the right.
Are my applications compatible?
See App Compatibility Table — RoaringApps.
Upgrading to Lion
If your computer does not meet the requirements to install Mavericks, it may still meet the requirements to install Lion.
You can purchase Lion by contacting Customer Service: Contacting Apple for support and service - this includes international calling numbers. The cost is $19.99 (as it was before) plus tax. It's a download. You will get an email containing a redemption code that you then use at the Mac App Store to download Lion. Save a copy of that installer to your Downloads folder because the installer deletes itself at the end of the installation.
Lion System Requirements
1. Mac computer with an Intel Core 2 Duo, Core i3, Core i5, Core i7,
or Xeon processor
2. 2GB of memory
3. OS X v10.6.6 or later (v10.6.8 recommended)
4. 7GB of available space
5. Some features require an Apple ID; terms apply. -
I updated to a newer version of iTunes and now my ipod touch does not show up as a device in iTunes. There is no 'Devices" category on the bar at the left
Refer to this article:
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538
Maybe you are looking for
-
Starting sample1 from the proc demo and entering an employee number shows up: ORA-00600: internal error code, arguments: [ktsircinfo_num1], [0], [1], [17585], [], [], [], [] which doesn't look like employee data Same result when trying a select to on
-
Helo I have recently aquired a static IP address from my ISP.. We have about 4 other macs and 1 PC on the network. My vision was to ultimately connect to a particular computer from home using remote access but my knowledge of this is quite limited. I
-
Carl's Report Row with Detail Example
Hi, Hoping someone can assist, I am looking at using Carl's "Report Row with Detail" example at: http://apex.oracle.com/pls/otn/f?p=11933:1 The only thing that I am unsure about is that , instead of using the words show comments/hide comments, I woul
-
Transferring data from 9300 to E90.
I currently have a 9300 and am looking to change to the E90. When I upgraded from the 9210i to the 9300 the process was easy enough to transfer my data. Before I buy the E90 is it possible to transfer all my data, via the backed up copy or with the a
-
CJQ0 process session is in idel stat
Session Idel Hi, Version 10204. All my database jobs are running using dbms_scheduler as you can see : select count(*) from dba_jobs; COUNT(*) 0 SELECT COUNT(*) FROM DBA_SCHEDULER_JOBS; COUNT(*) 20 show parameter job_q NAME