Ni-fbus communications cannot connect interface

I am using NI-FBUS Communications Manager 3.2 with a NI PCMCIA-FBUS Series 2 card in a Ricoh R/RL/... series PCMCIA adapter on a desktop computer. I enabled the PCMCIA card via the Interface Configuration Utility. When I start the Comm Manager, I get the following error message:
NI_FBUS Communications Manager cannot connect interface 0 on the fieldbus board 1. Click OK to.....
Windows sees the Ricoh adapter card and the Series 2 card as working properly. If I install the Series 2 card in a laptop, the Comm Manager starts properly. The same series 2 card and Ricoh adapter card has been used in another desktop computer also running XP SP2.
How do I get this combination up and running?

I tried the PCMCIA card and adapter card in another computer running XP and NI-FBUS Communications Manager 3.1.1. The combination worked properly; the card was seen and the Comm Manager opened. When Configurator was opened, the device attached to the link was seen.
Is there a compatibility difference between Comm Mgr 3.1.1 and 3.2?

Similar Messages

Can't connect to server "Cannot load Interface Builder File "NSAlertPanel"

all of a sudden, one of my Macs cannot connect to our server due to this error in the Console:
NetAuthAgent [ 128 ] Cannot load Interface Builder File 'NSAlertPanel'
This is on a MacPro running 10.6.4 - rebooting this computer didn't help.
My searches on Google regarding this message didn't pull results related to connecting to a server.
The error appears when in the Finder and you type Command + K or if you select Go in the menu and then select "Connect to Server". The "Connecting to Server" window does appear but it just sits there like it's trying to connect to our server. The login window should appear but it doesn't.
This happens both with AFP and SMB - it never connects and that error message i posted shows up in the Console whenever I attempt to connect.
Any ideas?
more info: i logged in as Root and the problem isn't there so it's isolated to the other profile. the problem is, i can't always use the Root profile.
Message was edited by: ifone_lover
Message was edited by: ifone_lover

I would recommend the usual basic troubleshooting:
1) Repair Permissions in Disk Utility, then reboot.
If that doesn't work,
2) Re-apply the latest Combo Update in safe mode (boot while holding shift).
http://support.apple.com/kb/DL1048

Cannot connect C3548XL to CNA community.

Hello,
I have a WS-C3548-XL-EN switch running ios v12.0(5)WC17 (fc1) that I can not get to connect into a community in CNA v6.1.
I have reset the switch to 'factory defaults', set the IP, SNM, and Default gateway. From other posts I saw that from the config prompt, I needed to enable HTTP (ip http server; ip http authentication enable; ip http path flash:html) and CDP (cdp run), but I still cannot connect.
There must be something I am missing, but being very new to the Cisco ios and this older switch, I don't know where to go.
Any guidance / help would be greatly appreciated.
Thanks in advance.
Bob

Yes - definitely not supported:
Legacy Devices
These devices are not supported by Network Assistant:
Catalyst 2900 XL switches
Catalyst 3500 XL switches
C1700 Series Modular Access Routers
Reference

Cannot initialize interface transport

I installed nifbus 3.0 and setup the interface card to connect through controlnet to an allenbradley linking device. I can see everything in RSLinx on the segment but when I try and rub the configurator softwater if returns a fatal error " NIFbus cannot initialize interface transport". Do you haev a solution around fixing this? I have uninstalled and re-installed everything and setup everything a couple of times but still cannot get it to run.
PLease call me if you can @312-330-5034 or email me an answer.
Thanks
HUgh Roddy

Hello,
Please be aware that NI-FBUS should work with the OEM version of RSLinx. NI-FBUS must call some DLL's from RSLinx OEM to visit the ControlNet resources. If RSLinx Lite is currently working on your computer, it prevents the 3rd party software (NI-FBUS) from calling these DLL's. Please contact Rockwell for the version information of RSLinx.
Hope it helps and please feel free to let us know if we could do more help for you!
Josiane Zhou
National Instruments China
Product Support Engineer for NI-FBUS

NI-FBUS Communications Manager 4.0.1 Error

I have dual LAN connection on my notebook as enclosed in the first picture.
The NI-FBUS Interface Configuration Utility recognises the connection to the HSE linking device without any errors, see second picture.
Ping to the address is OK, but the NI-FBUS Communications Manager 4.0.1 can not listen to the board 0, see third picture.
Using another notebook separated with only one LAN interface the connection is functioning.
Any ideas on the problem solution?
Attachments:
Dual_LAN_Problem.jpg ‏275 KB
NI_InterfaceConfigurator_OK.jpg ‏101 KB
NI_FBUS CommunicationsManager_Error.jpg ‏138 KB

Hi Chris,
I am not able to stop the Symantec Protection, see the pictures enclosed, perhaps I do not have the right for this application.
Even if I defined the fixed IP addresses as Exceptions not to be scanned, it does not work.
I will discus it at the company next week when I am working there.
Thanks for the hint.
Petr
Attachments:
SymantecExceptions.jpg ‏77 KB
SymantecProtection.jpg ‏22 KB

[WORKAROUND] Cannot connect to any WiFi network after resume

Hi, I'm having one weird problem that makes my laptop not as mobile as I'd like it to be..
Literally, I have to boot it up again after each move.
Here's the issue: if I suspend to ram, and then resume in a place with different WiFi network, it can't connect to Internet again.
I'm using NetworkManager via corresponding plasmoid in KDE (although, nmcli does not work either).
When I click a network name, I get the following:
"Configuring interface" .... -> Cannot connect to {NetworkName}
(the labels might be a bit different, as I get all notifications in my local language)
Have anyone experienced this before?
Or, AT LEAST, how can I get a bit more verbose output from NetworkManager? Is there a log file?
Here's the hardware:
05:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01)
Here's what I've tried already (and it didn't help):
# systemctl restart NetworkManager
# modprobe -r ath9k
# ncmcli nm sleep false
WORKAROUND FOUND: When I get "Configuring interface" .... -> Cannot connect to {NetworkName} (it happens not only after resumes, btw), I type the following in the console:
sudo dhcpcd -k
So much time passed, so many updates -- still have to do this manually... %)
Last edited by mityukov (2013-12-03 10:19:12)

hadrons123 wrote:Try these methods
https://bbs.archlinux.org/viewtopic.php?pid=1241694
Here's what I've tried:
# stop NetworkManager first, just in case if it would not start anything before time
sudo systemctl stop NetworkManager
# kill wpa_supplicant (one of suggestions in the topic)
sudo killall wpa_supplicant
# re-load kernel module with nohwcrypt=1 (another suggestion in the topic):
sudo modprobe -r ath9k
sudo modprobe ath9k nohwcrypt=1
# start NetworkManager again
sudo systemctl start NetworkManager
Then tried to connect the network again: the issue is till the same. Here's the latest dmesg:
$ sudo dmesg -c
[ 3079.006749] ath9k: ath9k: Driver unloaded
[ 3111.623220] cfg80211: Calling CRDA to update world regulatory domain
[ 3111.694588] ath: phy0: ASPM enabled: 0x43
[ 3111.694594] ath: EEPROM regdomain: 0x65
[ 3111.694596] ath: EEPROM indicates we should expect a direct regpair map
[ 3111.694599] ath: Country alpha2 being used: 00
[ 3111.694600] ath: Regpair used: 0x65
[ 3111.697195] ieee80211 phy0: Selected rate control algorithm 'ath9k_rate_control'
[ 3111.697465] ieee80211 phy0: Atheros AR9285 Rev:2 mem=0xffffc900140a0000, irq=16
[ 3111.717234] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 3136.958046] r8169 0000:03:00.0 eth0: link down
[ 3136.958159] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 3138.903691] wlan0: authenticate with 00:24:8c:65:bb:d5
[ 3138.911517] wlan0: capabilities/regulatory prevented using AP HT/VHT configuration, downgraded
[ 3138.911567] wlan0: send auth to 00:24:8c:65:bb:d5 (try 1/3)
[ 3138.917180] wlan0: authenticated
[ 3138.917697] ath9k 0000:05:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 3138.917711] ath9k 0000:05:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 3138.917718] ath9k 0000:05:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 3138.918897] wlan0: associate with 00:24:8c:65:bb:d5 (try 1/3)
[ 3138.932402] wlan0: RX AssocResp from 00:24:8c:65:bb:d5 (capab=0x411 status=0 aid=3)
[ 3138.932553] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 3138.932790] wlan0: associated
[ 3139.406632] wlan0: deauthenticating from 00:24:8c:65:bb:d5 by local choice (reason=3)
[ 3139.415815] cfg80211: Calling CRDA to update world regulatory domain
[ 3143.712977] wlan0: authenticate with 00:24:8c:65:bb:d5
[ 3143.720532] wlan0: capabilities/regulatory prevented using AP HT/VHT configuration, downgraded
[ 3143.720582] wlan0: send auth to 00:24:8c:65:bb:d5 (try 1/3)
[ 3143.731367] wlan0: authenticated
[ 3143.731865] ath9k 0000:05:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 3143.731882] ath9k 0000:05:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 3143.731888] ath9k 0000:05:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 3143.735093] wlan0: associate with 00:24:8c:65:bb:d5 (try 1/3)
[ 3143.748277] wlan0: RX AssocResp from 00:24:8c:65:bb:d5 (capab=0x411 status=0 aid=3)
[ 3143.748533] wlan0: associated
[ 3144.140732] wlan0: deauthenticating from 00:24:8c:65:bb:d5 by local choice (reason=3)
[ 3144.148708] cfg80211: Calling CRDA to update world regulatory domain
[ 3148.642615] wlan0: authenticate with 00:24:8c:65:bb:d5
[ 3148.650085] wlan0: capabilities/regulatory prevented using AP HT/VHT configuration, downgraded
[ 3148.650132] wlan0: send auth to 00:24:8c:65:bb:d5 (try 1/3)
[ 3148.665772] wlan0: authenticated
[ 3148.666264] ath9k 0000:05:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 3148.666278] ath9k 0000:05:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 3148.666284] ath9k 0000:05:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 3148.667980] wlan0: associate with 00:24:8c:65:bb:d5 (try 1/3)
[ 3148.681955] wlan0: RX AssocResp from 00:24:8c:65:bb:d5 (capab=0x411 status=0 aid=3)
[ 3148.682212] wlan0: associated
[ 3149.016733] wlan0: deauthenticating from 00:24:8c:65:bb:d5 by local choice (reason=3)
[ 3149.031462] cfg80211: Calling CRDA to update world regulatory domain
[ 3153.648602] wlan0: authenticate with 00:24:8c:65:bb:d5
[ 3153.656323] wlan0: capabilities/regulatory prevented using AP HT/VHT configuration, downgraded
[ 3153.656374] wlan0: send auth to 00:24:8c:65:bb:d5 (try 1/3)
[ 3153.659859] wlan0: authenticated
[ 3153.660389] ath9k 0000:05:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 3153.660403] ath9k 0000:05:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 3153.660410] ath9k 0000:05:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 3153.663889] wlan0: associate with 00:24:8c:65:bb:d5 (try 1/3)
[ 3153.672276] wlan0: RX AssocResp from 00:24:8c:65:bb:d5 (capab=0x411 status=0 aid=3)
[ 3153.672536] wlan0: associated
[ 3153.967817] wlan0: deauthenticating from 00:24:8c:65:bb:d5 by local choice (reason=3)
[ 3153.980619] cfg80211: Calling CRDA to update world regulatory domain

Cannot connect to Exchange 2007 server on OS 3.1

Hi
Since I've upgraded to OS 3.1 on my iPhone 3GS I cannot connect to my Exchange 2007 server. The phone simply tells me "The connection to the server failed.".
What could this be? I've read the problems that 3G people are experiencing, but I've got the 3GS.
Is there anyway to debug this? The Exchange server works fine in Outlook and I can even connect to the web interface through Safari on the iPhone.
Any suggestions?
Best regards,
Thomas René Sidor

Hi,
Seems you have found the solution here:
http://social.technet.microsoft.com/Forums/exchange/en-US/5b7d250e-c995-4322-b1e7-5ad14ace81c5/cannot-connect-to-exchange-2013-server-prompt-for-username-and-password-that-are-not-accepted?forum=exchangesvrgeneral#d266273b-e04c-45a9-8b0f-8b48bf647a86
I'm post the answers here so that it will benefit for other community members who have similar qustions:
Install the
November
2012 Update for Outlook 2007 SP3 to resolve the problem.
Thanks for our MCC steve siyavaya.
Cheers,
Steve Fan
TechNet Community Support

Exchange active sync cannot connect to server after migration mailbox user from exchange 2007 to exchange 2013 coexistence

Hello, everyone, my name is rafl
I have a problem with exchange 2013 active sync.
I have installed exchange 2013 coexistence with legacy exchange 2007, I have to migrate user mailboxes: [email protected] from exchange 2007 to exchange 2013.
but any problem with active sync connection on the mobile device after moving mailbox user. I reconfigure the exchange ActiveSync external connection domain (latest.domain.com) on mobile device replacing legacy exchange ActiveSync external connection domain
(legacy.domain.com)
the process of moving mailboxes successfully without error.
Access OWA for exchange 2007 and exchange 2013 is running normally
access mail from Outlook running normally
Certificate request has been installed and has no problem with it
The OWA virtual directory is configured for internal and external connections and different from the legacy exchange
The autodiscover virtual directory is configured for internal and external connections and different from the legacy exchange
ActiveSync virtual directory is configured for internal and external connections and different from the legacy exchange
user mailboxes are still on exchange 2007 is not problematic.
only problem with Exchange Active Sync on mobile devices, where I set up an email with android, iphone, windows phone. the error message: cannot connect to the server.
but, if I create a new user and create user mailboxes directly in exchange server 2013, ActiveSync can run without error on mobile device, access through OWA, MsOutlook, Outlook Anywhere also run normally.
only the results of user migration from exchange 2007 to exchange 2013 which is troubled with exchange ActiveSync connection.
any ideas for this problem, and what should I check on the exchange server ..?

i have run the activesync test connectivity and get some error :
Testing TCP port 443 on host domain.co.id to ensure it's listening and open.
The specified port is either blocked, not listening, or not producing the expected response.
A network error occurred while communicating with the remote host.
Elapsed Time: 3091 ms.
Testing TCP port 443 on host autodiscover.domain.co.id to ensure it's listening and open.
The specified port is either blocked, not listening, or not producing the expected response.
A network error occurred while communicating with the remote host.
Elapsed Time: 21072 ms.
Testing TCP port 80 on host autodiscover.domain.co.id to ensure it's listening and open.
The specified port is either blocked, not listening, or not producing the expected response.
A network error occurred while communicating with the remote host.
Elapsed Time: 21049 ms.
I have allowed access to port 443 (https) and 80 (http) on the firewall and re-run testconnectivity, but still with the same results. if I enable active sync for users who created directly in Exch 2013 there is no problem with the ActiveSync, just a problem
for users who moved from Exch 2007 to Exch 2013. @Android, iPhone, and Blackberry the error message "cannot connect to the server"

My macbook pro cannot connect to internet via wifi

I have a Macbook Pro 2010 OS X 10.8.3. I cannot connect to internet via wifi (Air por). My Macbook Pro does not recognize my network and when I select it from the list of network it asks for my network password. when I type in my password a dialog box gives me timeout error. Please could anyone help me. I am using ethernet for my connection at the moment. Do I need to reset my macbookpro? if yes, what will happen to my applications and operating system (mountain lion)?
Monireh

When you use the Airport utility what happens?
What is in the System Preferences control panel for Network settings?
http://www.apple.com/support/airport - there is a forum just for Airport Community
Airport Express FAQ
http://support.apple.com/kb/HT1515
Wi-Fi Setup Considerations
Things to consider before you begin
Start with a plan for the physical layout. Depending on whether you have an existing Wi-Fi network, or if you are using your AirPort Express as a standalone Wi-Fi device, there are several options available for you to choose from.
When using Ethernet, Cat6 cable is recommended.
The layout you choose should take into account environmental factors such as physical access, location, range, radio frequency interference, etc.
You will need to consider what AirPort Utility settings to adopt.
You will need to know whether you are using an AirPort Express (802.11b/g) or an AirPort Express (802.11a/b/g/n).
If you will be using more than one Wi-Fi base station, it may be helpful to read the article Extending the range of your wireless network by adding additional Wi-Fi base stations.
AirPort Discussions
Discuss your AirPort Base Station, Time Capsule and Wi-Fi questions with fellow community members.
More
Direct you to the proper forum for MacBook :
MacBook Series Forumshttps://discussions.apple.com/community/notebooks?view=discussions
Mac OS X Forums
https://discussions.apple.com/community/mac_os?view=discussions
http://www.apple.com/support/macbookpro

Cannot connect to ASDM on ASA 5505 over https

Problem: Cannot connect to ASDM on ASA 5505 when vlan1 network is changed from the factory default.
Hi all. I am just getting started on a new ASA 5505, working it in a test lab environment. I ran thru the initial setup wizard. During that time I specified a name for Vlan1 (changed from 'inside' to 'INTR-NET'), modified the Vlan1 IP address to use DHCP, and then populated the Device Config Access table with entries corresponding to the entire Class B network here on the local intranet. I don't recall if the factory-default network was already populated, but if it wasn't I added it as 192.168.1.0/255.255.255.0
I then saved the config, and verified that the ASA got a dhcp address using the RS-232 console. I then reconfigured the laptop I have plugged into port 0/1 with it's normal address on the intranet and discovered that I couldn't reconnect to ASDM. The ASDM client times out, and a web browser opened to https://(ASA5505's dhcp addr) fails as well.
I then used the console to add another http IP address matching the specific IP address (xxx.240.113.129/255.255.255.255) which the laptop is set for, to the list of permissible admin connections, but saw no difference.
This issue is much the same as was reported in this prior forum posting:
http://forums.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Security&topic=General&topicID=.ee6e1f8&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.2cc16cb8/4
EXCEPT that I was already aware the admin IP address(es) needed to be registered to enable access via SSH/Telnet/HTTPS.
And, I did that step, but it is not working. I have tried adding various combinations of network ranges in the device config access list, including the specific subnet that the lab's dhcp server assigned to the ASA 5505 (xxx.240.112.0/255.255.254.0), but there is no difference. I can traceroute to the laptop and ping the Vlan1 interface from the laptop, but the https ASDM (and ssh connections too) are not successful. This is very frustrating.
The device is brand new, I see that upon boot it loads asa724-k8.bin, and the software banner says Cisco Adaptive Security Appliance Software Version 7.2(4)
Note also that, from the RS-232 console, if I reset the IP address to the static, factory default (192.168.1.1) and manually config my laptop on the same subnet, then ASDM makes the connection. Just like out of the box. But when I put it back onto our intranet and verify the DHCP lease, then ASDM is a no go.
Can you think of what I've missed?

Good question. Let me add that info plus related Vlan config details:
ASA5505A# show ip
System IP Addresses:
Interface Name IP address Subnet mask Method
Vlan1 INTR-NET XXX.240.112.92 255.255.254.0 DHCP
Vlan2 VoIP 172.26.99.1 255.255.255.0 manual
Vlan3 dmz-unused 192.168.99.1 255.255.255.0 manual
Current IP Addresses:
Interface Name IP address Subnet mask Method
Vlan1 INTR-NET XXX.240.112.92 255.255.254.0 DHCP
Vlan2 VoIP 172.26.99.1 255.255.255.0 manual
Vlan3 dmz-unused 192.168.99.1 255.255.255.0 manual
ASA5505A# show switch vlan
VLAN Name Status Ports
1 INTR-NET up Et0/1, Et0/2, Et0/3, Et0/4
2 VoIP down Et0/5, Et0/6, Et0/7
3 dmz-unused down Et0/0
ASA5505A#
ASA5505A# config t
ASA5505A(config)# show running-config http
http server enable
http XXX.240.0.0 255.255.0.0 INTR-NET
http 192.168.1.0 255.255.255.0 INTR-NET
http XXX.240.113.129 255.255.255.255 INTR-NET
ASA5505A(config)#
ASA5505A(config)# show running-config ssh
ssh 192.168.1.0 255.255.255.0 INTR-NET
ssh XXX.240.0.0 255.255.0.0 INTR-NET
ssh timeout 5
SECURITY LEVEL IS 100 ON Vlan1 and Vlan2, 50 on Vlan3, and traffic is restricted from Vlan3 to Vlan1 because this is the basic license.

Data Model damaged, Cannot connect to Access 2013 from within Excel 2013

Hello,
Recently I am not able to use PowerPivot for Excel 2013 and I cannot connect to my Access 2013 database tables from within Excel 2013. Whenever I try to click on a slicer in my Excel worksheet, it gives me the following error: "Excel was unable to load
a necessary component. This component might have been damaged or deleted. Reinstall the client software or data source driver software for your database."
I am using Microsoft Office Pro Plus 2013 on Windows 7, 64-bit version. I have tried reinstalling Microsoft SQL Compact Edition 2005 and reinstalling Office 2013. I have run out of ideas and am a loss what to do next ?
Can anyone help point in the right direction for a possible solution to this problem ???
Would appreciate all help.
Thank you.
~Maneesh
The problem with being punctual is, there's nobody there to appreciate it !!!

Hi
This is the forum to discuss questions about apps for office develop. For your question is more about Excel, I will move this thread to the TechNet forum for
Excel
The reason why we recommend posting appropriately is you will get the most qualified pool of respondents, and other partners who read the forums regularly
can either share their knowledge or learn from your interaction with us.
Thank you for your understanding.
Best Regards
Lan
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

SharePoint 2007:Cannot connect to the configuration database.

The share point 2007 server under Windows Server 2008 R2 runs well formerly, but suddenly the user can't visit the site with error on page:
Cannot connect to the configuration database.
I also checked windows log with bellow main errors：
Log Name:      Application
Source:        Office Server Search
Date:          2015/2/28 22:30:47
Event ID:      10034
Task Category: Gatherer
Level:         Error
Keywords:      Classic
User:          N/A
Computer:      ***
Description:
Could not access the Search service configuration database.
Context: Application 'b9f7f366-4027-4923-b5ce-b93c132df7c3'
Details:
Unspecified error
(0x80004005)
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
    <Provider Name="Office Server Search" />
    <EventID Qualifiers="49152">10034</EventID>
    <Level>2</Level>
    <Task>3</Task>
    <Keywords>0x80000000000000</Keywords>
    <TimeCreated SystemTime="2015-02-28T14:30:47.000000000Z" />
    <EventRecordID>2323514</EventRecordID>
    <Channel>Application</Channel>
    <Computer>***</Computer>
    <Security />
</System>
<EventData>
    <Data>
Context: Application 'b9f7f366-4027-4923-b5ce-b93c132df7c3'
Details:
Unspecified error
(0x80004005)</Data>
</EventData>
</Event>
======================================
Log Name:      Application
Log Name:      Application
Source:        Windows SharePoint Services 3
Date:          2015/2/28 22:30:50
Event ID:      5586
Task Category: Database
Level:         Error
Keywords:      Classic
User:          N/A
Computer:      ***
Description:
Unknown SQL Exception 64 occured. Additional error information from SQL Server is included below.
A connection was successfully established with the server, but then an error occurred during the login process. (provider: TCP Provider, error: 0 - The specified network name is no longer available.)
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
    <Provider Name="Windows SharePoint Services 3" />
    <EventID Qualifiers="0">5586</EventID>
    <Level>2</Level>
    <Task>484</Task>
    <Keywords>0x80000000000000</Keywords>
    <TimeCreated SystemTime="2015-02-28T14:30:50.000000000Z" />
    <EventRecordID>2323517</EventRecordID>
    <Channel>Application</Channel>
    <Computer>***</Computer>
    <Security />
</System>
<EventData>
    <Data>64</Data>
    <Data>A connection was successfully established with the server, but then an error occurred during the login process. (provider: TCP Provider, error: 0 - The specified network name is no longer available.)</Data>
</EventData>
</Event>
==================================================
Source:        Windows SharePoint Services 3
Date:          2015/2/28 22:31:00
Event ID:      27745
Task Category: General
Level:         Error
Keywords:      Classic
User:          N/A
Computer:      ***
Description:
The description for Event ID 27745 from source Windows SharePoint Services 3 cannot be found. Either the component that raises this event is not installed on your local computer or the installation is corrupted. You can install or repair the component on
the local computer.
If the event originated on another computer, the display information had to be saved with the event.
The following information was included with the event:
#50071: Unable to connect to the database SP_Config on ***. Check the database connection information and make sure that the database server is running.
the message resource is present but the message is not found in the string/message table
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
    <Provider Name="Windows SharePoint Services 3" />
    <EventID Qualifiers="14130">27745</EventID>
    <Level>2</Level>
    <Task>1105</Task>
    <Keywords>0x80000000000000</Keywords>
    <TimeCreated SystemTime="2015-02-28T14:31:00.000000000Z" />
    <EventRecordID>2323520</EventRecordID>
    <Channel>Application</Channel>
    <Computer>***</Computer>
    <Security />
</System>
<EventData>
    <Data>#50071: Unable to connect to the database SP_Config on ***. Check the database connection information and make sure that the database server is running.</Data>
</EventData>
</Event>
Please kindly support to find the root cause and guide how to fix it ASAP.
Many appreciations for your hellp in advance!
Note:
1)As checked, SQL server service is running well;
2)Web server log under the path C:\Program Files\Common Files\Microsoft Shared\Web Server Extensions\12\LOGS with bellow errors:
03/02/2015 11:25:53.28 mssearch.exe (0x0F0C)                   0x08FC Search Server Common
GathererSql                   0 Monitorable CSqlCrawl::ExecuteCommand() Failed in GetSession, Error is 0x80004005 - File:d:\office\source\search\search\gather\server\gatherobj.cxx
Line:9654
03/02/2015 11:25:53.39 mssearch.exe (0x0F0C)                   0x08FC Search Server Common          Common
0 Monitorable Application b9f7f366-4027-4923-b5ce-b93c132df7c3, resource 1: pIDBInitialize->Initialize error. Failed to create a non fast load session. - File:d:\office\source\search\search\searchdll\resourcemanagerimpl.cpp Line:608
03/02/2015 11:25:53.39 mssearch.exe (0x0F0C)                   0x08FC Search Server Common          Common
0 Monitorable CResourceManager::CreateSession Error creating non fastload session 'Provider=SQLOLEDB;Extended Properties='Server=***;Database=SP_SharedServices_Search;Trusted_Connection=yes;App=Windows SharePoint Services;Timeout=15';'. - File:d:\office\source\search\search\searchdll\resourcemanagerimpl.cpp
Line:658
03/02/2015 11:25:53.39 mssearch.exe (0x0F0C)                   0x08FC Search Server Common          UtilCommon
0 Monitorable Dumping error record [0]:   Source: Microsoft OLE DB Provider for SQL Server   HRESULT: 0x80004005   Code: 11   Description: [DBNETLIB][ConnectionRead (recv()).]General network error. Check
your network documentation. - File:d:\office\source\search\common\pkmutild\atldbext.cxx Line:1250
03/02/2015 11:25:53.39 mssearch.exe (0x0F0C)                   0x08FC Search Server Common          GathererSql
0 Monitorable CSqlCrawl::ExecuteCommand() Failed in GetSession, Error is 0x80004005 - File:d:\office\source\search\search\gather\server\gatherobj.cxx Line:9654

Hi,
In this forum we mainly discuss questions and feedbacks about Office products, since your question is about SharePoint, I suggest you post the question in SharePoint forum to get further assistance:
https://social.technet.microsoft.com/Forums/office/en-US/home?category=sharepoint
The reason why we recommend posting appropriately is you will get the most qualified pool of respondents, and other partners who read the forums regularly can either share their knowledge or learn from your interaction with us. Thank you for your understanding.
Regards,
Melon Chen
TechNet Community Support
It's recommended to download and install
Configuration Analyzer Tool (OffCAT), which is developed by Microsoft Support teams. Once the tool is installed, you can run it at any time to scan for hundreds of known issues in Office
programs.

Cannot connect to the phone system. An unidentified error has occurred, Please try again.

Issue: Lync 2013 users with remote call control enabled cannot connect to the phone system. When the user logs into Lync, they see an exclamation in the bottom right corner
with this error.
Error: Cannot connect to the phone system. An unidentified error has occurred, Please try again. If the problem continues, please contact your support team.
Environment:
1 site: Site1
2 Pools:
1. Lync 2010
Trusted application is added here for the site.
2. Lync 2013
Avaya phone system: AES r6-1-2-32-0
I have not moved the trusted application to the Lync 2013 pool yet, but my understanding is that it should still work since it’s in the site. Is my understanding on this correct? (All of my other trusted applications do work for Lync 2013
users & none of them have been moved yet. Remote Call Control is the only one that does not work.)
This is from the uccapi log. This is just from the user logging in, not actually making a call. Below are the items that I think are important, however, I don’t know how to interpret it to determine if the problem is on the Lync side or
the Avaya side. Here’s a summary:
SIP/2.0 100 Trying
Authentication-Info: TLS-DSK qop="auth", opaque="5FD217E1", srand="E05700E2", snum="9", rspauth="f308eae87c0bbe64a1ab213574776cbdf9823ab6", targetname="lync03.domain.com",
realm="SIP Communications Service", version=4
From: <sip:[email protected]>;tag=bbb282ebbd;epid=a86d5b0a29
To: <sip:[email protected]>
Call-ID: 9eb0d23a3b8f4e0eafc6c6da622fbecf
CSeq: 1 INVITE
Via: SIP/2.0/TLS 10.155.48.96:61472;ms-received-port=61472;ms-received-cid=1FA400
Server: http%3A%2F%2Fwww.microsoft.com%2FLCS%2FUdcAgent
Content-Length: 0
SIP/2.0 200 OK
Authentication-Info: TLS-DSK qop="auth", opaque="5FD217E1", srand="15C0F9A2", snum="13", rspauth="4fd891e39a33e902fb1cec5d980e5bf0ccb172a0", targetname="lync03.domain.com",
realm="SIP Communications Service", version=4
From: <sip:[email protected]
>;tag=bbb282ebbd;epid=a86d5b0a29
To: <sip:[email protected]
>;tag=A7A45C856ECD79121A1827265ABBD7F6
Call-ID: 9eb0d23a3b8f4e0eafc6c6da622fbecf
CSeq: 1 CANCEL
Via: SIP/2.0/TLS 10.155.48.96:61472;ms-received-port=61472;ms-received-cid=1FA400
Server: http%3A%2F%2Fwww.microsoft.com%2FLCS%2FUdcAgent
Content-Length: 0
SIP/2.0 487 Request terminated
Authentication-Info: TLS-DSK qop="auth", opaque="5FD217E1", srand="F46EC133", snum="14", rspauth="1d92718caa4f61d967faa46a5c256aafa8b4e740", targetname="lync03.domain.com",
realm="SIP Communications Service", version=4
From: <sip:[email protected]
>;tag=bbb282ebbd;epid=a86d5b0a29
To: <sip:[email protected]
>;tag=A7A45C856ECD79121A1827265ABBD7F6
Call-ID: 9eb0d23a3b8f4e0eafc6c6da622fbecf
CSeq: 1 INVITE
Via: SIP/2.0/TLS 10.155.48.96:61472;ms-received-port=61472;ms-received-cid=1FA400
ms-diagnostics: 5002;reason="Request was cancelled";AppUri="http%3A%2F%2Fwww.microsoft.com%2FLCS%2FUdcAgent";source="lync03.
domain.com"
Server: http%3A%2F%2Fwww.microsoft.com%2FLCS%2FUdcAgent
Content-Length: 0

Hi Suelizy,
To better understand the issue, I would like to collect the following information for troubleshooting:
1. Do you mean the Lync 2010 user can connect to the Phone System?
2. What’s next hop pool of the application?
In a mixed environment, you must set the next hop pool to be the Lync Server 2013 pool.
Best regards,
Eric

Cannot connect to an Exchange account in Outlook 2013 using "Microsoft Exchange Server or Compatible Service"

Dear All,
I cannot connect to my Exchange account in Outlook 2013 using "Microsoft Exchange Server or Compatible Service".
First I would like to present my network environment, I have 4 physical servers;
The first one is holding the Domain Controller 1, IP@: 192.168.1.10
The second server is holding the additional Domain Controller which it is DC2, IP@: 192.168.1.11
The third server is holding the Exchange 2013 Mailbox, IP@: 192.168.1.15
And the last server is holding the Exchange 2013 CAS-HT, IP@: 192.168.1.16
I am doing the steps below:
1-Creating a new profile in outlook and start configuring the exchange account by entering the IP address of the Exchange-CAS Server, 192.168.1.16
2-entering the account name: [email protected]
3-Go to "More Settings" > "Connection" > "Connect to Microsoft Exchange using HTTP" > and entering the "Exchange Proxy Settings"
4-type the exchange CAS Server URL, https://192.168.1.16
5-Check the "Connect using SSL Only"
6-Authentication Settings: "NTLM Authentication", and pressing Apply
7-When I press the "Check Name" button, a message occurred> "The action cannot be completed. The connection to Microsoft Exchange is unavailable. Outlook must be online or connected to complete this action".
8-I go back to the "Exchange Proxy Settings" and I Uncheck the "Connect using SSL Only" and pressing Apply
9-i press the "Check Name" Button, a small window occurred to enter a Username and Password, so I enter the Administrator username and the administrator password and pressing "OK", but nothing is changed, I tried to enter my
username and password in the small window and I still got the same result.
I cannot verify the account name and I cannot complete the process.
I appreciate you kind assistance.

Hi,
To narrow down the cause, I’d like to recommend the following troubleshooting:
1. Try to login the test account through OWA.
2. Check the Autodiscover settings: get-clientaccessserver |fl autodiscoverserviceinternaluri
3. Check the result of directly accessing the following URL:
https://autodiscover.domain.com/autodiscover/autodiscover.xml
Thanks,
Angela
Angela Shi
TechNet Community Support

Cannot Connect to Google Calendar in Mail, Contacts & Calendars preferences

I recently obtained a new Mac and am playing with Mountain Lion for the first time. I'm trying to add my Google Apps (custom domain, not @gmail.com) account to the Mail, Contacts & Calendars control panel. I was able to add Mail, Messages, and Notes without any issues, but it's refusing to connect to Calendars & Reminders. When I attempting connecting, it gives me an error...
A secure connection couldn't be established.
Click “Continue” to continue creating the account. You can edit the account later in Calendar preferences if necessary.
So I click "Continue" to... well, continue. Eventually, I've given this error:
There was a problem setting up the account.
Calendar couldn't discover the account settings for the CalDAV server “google.com”.
Just out of curiousity, I went into the Calendar app to directly add my Google account. Doing so also gives me an error:
Server with Secure Communication Unavailable
Your calendar account isn't on a server that can receive your calendar securely.
If a server isn't secure, others may be able to view your calendar information. To continue searching for your account on servers that may not be secure, and then set up the account if it's found, click Continue.
So I go ahead and click Continue. After waiting some more, I finally get the error...
No CalDAV servers were found for "google.com".
This message appears on the Account Settings sheet where you can add a CalDAV account. If I manually type in the Server Address here (https://www.google.com/calendar/dav/[email protected]/user//www.google.com/calendar/dav/[email protected]/user), Calendar claims it still cannot connect to a secure connection. This time, clicking Continue does add the account. (I'm assuming through a non-secure conncetion.) If I try to edit the Account Settings, it takes me to the Mail, Contacts, and Calendars control panel where Calendars & Reminders for my Google account is now selected.
I can only assume this is a weird bug with Mountain Lion, but needless to say, this is far from the "it just works" mentality I've been use to.
This was not an issue with iCal on Snow Leopard, which is what I'm coming from.

I was having similar issues and thought I would put down what solved my problem.
In "Mail, Contacts & Calendars" I didn't choose "Gmail" I used "Add Oter Account…" as previously mentiond.
Then I chose "Add a CalDav account"
Under User Name: I entered my entire gmail address
Under Password: I entered a new "Application Password" key as generated by Googles two step verification process.
Under Server Address: I tried to use just "google.com" and "www.google.com" neither of these worked - only errors. So I used the address as listed on Google Calender when clicking on settings for my main calendar. There is a link that will give you your calendars private address. I shortened it to:
www.google.com/calendar/ical/your_gmail_address_goes_here
Then it worked immediately!

Ni-fbus communications cannot connect interface

Similar Messages

Maybe you are looking for