NI LabVIEW RIO Evaluation Kit

I bought the NI LabVIEW RIO Evaluation Kit and i need the datasheet as soon as possible, please help. Thanks

This is a user supported forum, what you are asking for would best be handled through the formal National Instruments channels. If you can, contact your local National Instruments office for help. What are you looking for exactly, can it not be downloaded from the NI site? Usually all of that type of info is available online.
Putnam
Certified LabVIEW Developer
Senior Test Engineer
Currently using LV 6.1-LabVIEW 2012, RT8.5
LabVIEW Champion

Similar Messages

What's the maximum digital I/O frequency for the NI LabVIEW RIO Evaluation Kit ?

Hi!
I'm trying to analyze some sort of sine signal at the frequency of about 3 MHz. Because the analysis should be very precise and fast (about 10 samples per period), I'm needing the maximum digital I/O frequency of the NI LabVIEW RIO Evaluation Kit.
Regards,
Erik

Dracyon,
Can you please clarify a couple of things: you say you are trying to acquire a sine wave that has a frequency of 3 MHz, but you are asking for the maximum DIO frequency. I believe what you need to know is the maximum analog sampling frequency. For the sbRIO-9636 (part of the evaluation kit), the maximum aggregate sampling frequency is 200 kS/s at 16 bits of resolution. At 10 samples per period, you could sample a ~20k analog signal. If you are actually looking for maximum DIO frequency, this is a bit more complicated. We have a good whitepaper explaining this.
Best,
Tannerite
National Instruments

Less voltag in J502/DIO sbRIO 9636 (NI LabVIEW RIO Evaluation Kit )

Hello,
I bought the NI LabVIEW RIO Evaluation Kit (with sbRIO9636). I have problem with the sbRIO9636. The voltag in J502,DIO Pin 49 and 50 is less than 5V (just 1.7V). so VCC of the LabVIEW RIO Evaluation board with a digital encoder, LCD screen, function generation, etc. can't get the enough voltag (5V) und can't work.
For example >VCC of LCD screen is just 1.7 V and not to work. So this is a Hardware problem? Can man solve the problem?
Thank you!!
Attachments:
IO_sbRIO9636.PNG ‏79 KB

Hi Duffy and KellyDog,
+5V should be available on the pins and connector that Duffy is referencing.
KellyDog,
Couple of questions. Is anything connected to the sbRIO-9636 in addition to the power cable? Does the unit boot and connect to your host PC over ethernet? If the +5V power supply was damaged and only supplying ~1.7V, I wouldn't expect the board to boot, as all the onboard power supplies are derived from that rail. Has anything happened to the board that would cause you to suspect power supply damage? There is a fuse on the +5V pins, so is it possible that the 5V supply pins were accidentally shorted to ground, potentially damaging the fuse? If so, this board would need to be returned for repair (RMA) as the fuses are not user servicable.
Regards,
Spex
National Instruments
To the pessimist, the glass is half empty; to the optimist, the glass is half full; to the engineer, the glass is twice as big as it needs to be...

NI LabVIEW RIO Evaluation Kit online gain tuning.

Hi,
I am interested in using the NI LabVIEW RIO Evaluation Kit for the implementation of a PID controller. I want to know if it is possible to tune the PID gains of the controller implemented on this kit without halting the realtime operation? So for instance if the controller is controlling the speed of a DC motor, can I tune the PID gains from LabView without having to stop the kit?
Umar.
Solved!
Go to Solution.

Hi Umar,
Are you asking about the Auto Tuning feature or just plain tuning the PID manually? Either way, you should be able to tune your PID without stopping the kit.

Need pinout for connector of RIO Evaluation KIT

Hi Everyone
Does anyone know the pinout of th connectors in this board the ones on the left upper corner and thank you very much

Hi Ghassen14,
The RIO Evaluation Kit uses a sbRIO 9636:
http://sine.ni.com/nips/cds/view/p/lang/en/nid/210421
The manual for the sbRIO 9636 includes information about the pinouts of the sbRIO. The manual can be found at the link above or directly at the link below:
http://www.ni.com/pdf/manuals/373378d.pdf
Catherine B.
Applications Engineer
National Instruments

FPGA - RIO Evaluation Board - Using the LCD Display

I have the NI LabVIEW RIO Evaluation Board and am trying to find information on using the LCD display. Does anyone know of any documentation/app notes? Thanks in advance.

Thanks for the suggestions ramses64.
I failed to mention that I didn't install the software that came with the evaluation kit. The reason being, I already have LabVIEW and all the modules installed. I was not about to overwrite my perfectly good installation even if the instructions on the box tell me it is perfectly safe to do so.
If there are examples with the kit, then they are buried in an installer/cab file and not directly accessible by simply looking at the CD/DVD contents. I should install the evaluation software onto a virtual machine and see what is revealed.
I'll take a look at the LCD Module this evening and see if it provides any clues.
Thanks!

Student version and Evaluation Kit

Hallo .. I have a student version of Labview 2013, because of my study .. - and I borrowed a Evaluation Kit hardware from my work..
Can I connect them together, or do I need to have the software installed for the evaluation kit also ?
BR Mathias Them / Denmark

You need to be more specific. Are you talking about the RIO evaluation kit? (there are several others!)
If so, you also need e.g. the RT and FPGA software. You can find the 2013 execrcises and additional information here.
LabVIEW Champion . Do more with less code and in less time .

I need to program a Hittite Fractional-N Synthesizer Evaluation Kit with a HMC702LP6CE an external YIG oscillator. Not sure how to use Labview to control the PLL.

I need to program a Hittite Fractional-N Synthesizer Evaluation Kit with a HMC702LP6CE an external YIG oscillator. Not sure how to use Labview to control the PLL.

Here is how to use the PLL. But I don't know of how to interact with that device
http://zone.ni.com/devzone/cda/tut/p/id/3781
And for thouse who don't know what a PLL is a free bonus link is here:
http://digital.ni.com/public.nsf/allkb/07BC8D77D4E9AE258625708B007CE74F?OpenDocument
and a second one on what that device is: http://www.hittite.com/products/view.html/view/HMC702LP6CE
Now we are all caught up to speed.
Sam S
Applications Engineer
National Instruments

Rio evaluation

Hello World..........
Hi i am just after getting my hands on an sb Rio and the labview evaluation kit.
the question i have it when i start on the tutorial it instructs you to open various vi's and it goes through some basic functions .
This is where the problems start for me, within the vi's are sub vi's, and i cant seem to find these on my hard drive any where.
Has any one else had this problem? any advice at all would be greatly appreciated.

Did you install all the required drivers?
LabVIEW Champion . Do more with less code and in less time .

Embedded Software Evaluation Kit LV8.6 remote web panel

Hi,
I have recently purchased the Embedded Software Evaluation Kit which comes with LV8.6 90 day evaluation of FPGA, RT... and although I have sucessfully worked through the tutorial that with the kit I came across a problem when trying to run a remote web panel such that it showing loading 0% but never proceeded past this point.
After trawling through many discussion forums I came across a post which gave one of the reasons for this to happen as being due to having a newer version of LabVIEW run time engine installed on the PC - only by removing LabVIEW 2011 could I get the web panel to run.
My question is how do I manage multiple version of LabVIEW if I wish (and I do wish) to install more than one version of LabVIEW and still be able to run a remote panel via LV8.6?
Cheers,
Helen
CLD, CTD
Solved!
Go to Solution.

Hi Helen,
With development versions of LabVIEW you can deactivate them (using the NI license manager), but since the run-time engines are not licensed you can not deactivate that.
You could try running one of your LabVIEW versions in a virtual machine, thus separating them from each other.
I apologise for the problem that you have encountered, I appreciate that it inconveniences you quite a bit, but I assure you that your R&D team are looking into the issue.
Kind regards,
James W
Controls Systems Engineer
STFC

Start LabVIEW in evaluation mode

Hello All,
I am building an NI Dev Suite unattended/silent install which includes LabVIEW 2013, TestStand 2013, Switch Exec, some reuse libraries etc.
The installer works fine. After an automatic restart, I need to apply a configuration (automatically) using VI Package Manager and this requires LabVIEW to be working without prompts for licences etc.
Anyone know of a way to start LabVIEW in evaluation mode by default. Any ini tokens / registry entries may be?
I also need the same thing to happen with TestStand as I need to install some configuration to TestStand too.
All of the software will then be licensed by the user afterwards. I would like to avoid building two installers if I can help it.
thanks in advance.
aCe
CLA, CTA
Beginner? Try LabVIEW Basics
Sharing bits of code? Try Snippets or LAVA Code Capture Tool
Have you tried Quick Drop?, Visit QD Community.

I have not noticed any speed differences between licensed and evaluation modes.
R

How can I write program in Labview for zbrain kit..??

Hello everybody
I need to write the program in Labview fro Zbrain kit. I need to write code for multiple analog input (through multiple channels) that results multiple digital output. I found one refrence code which has one analog input (one channel) and gives one digital output.
I also need to save data for channels. I have no idea how can I save data for channels.
I have attached here the base program. Please give me idea how can I understand this program so that I can complete following tasks:
1. Save data for one channel and later for multiple channels
2. Modify the number of channels from one channels to multiple channels.
Actually I have gone through the videos and text based content(basics in labview) but I am unable to write the code.
Attachments:
Analog_3_InBlock.vi ‏131 KB

Hi,
Attached is an example snipped with some more comments on how to acquire multiple channels on a ZBrain platform that is based on an Analog Devices Blackfin processor. Just drag and drop it into your LabVIEW diagram. More examples can be found here: http://wiki.schmid-engineering.ch/zsystem/doku.php?id=example_zmc_adc-dma_continous. The idea behind dynamic data acquisition on a microprocessor is simple: you define the channels (up to 6x) , sampling frequency (up to 250kHz) and block sizes (up to 65'000) and start the acquisition. The underlying driver model samples in the data in parallel and the LabVIEW program gets this data. While e.g. processing the data, the underlying driver model continues sampling new data.
I hope this helped.
Marco Schmid
Schmid Engineering
Attachments:
snippet_zmc_adc-dma_continuous.png ‏107 KB

VMWare Evaluation Kit on Red Hat Linux

I have downloaded RHEL3-DVD2-Linux-v1[1].4.zip (793,301KB). When I try to open that file with WinZip I get the message "Cannot open file: bIt does not appear to be a valid archive. If you downloaded this file, try downloading the file again."
I have tried this several times without success.
The Oracle Universal Installer is at "Copying files for 'Oracle on Linux Evaluation - Oracle Software 10.1.0.2.0'" and is waiting with a Disk Location messagebox message 'Please insert OracleOnLinuxEvaluation disk 2 into your disk drive or specify an alternate location.'
Why does everything related to Oracle has to be difficult - even a simple download? Can someone please help with installing evaluation kit on Windows (XP,2000,or 2003).

Please post this question in the Oracle/VMware forum:
Desktop Datacenter
Cheers, OTN

LabVIEW 2010 Evaluation Mode not runing Real Time

LabVIEW 2010 Evaluation Mode not runing Real Time
Attachments:
real time.jpg ‏133 KB

Have you tried re-installing the Real-Time module (both on the target and the PC)?
Have you verified it's activated?
Have you tried re-installing the evaluation license files? http://joule.ni.com/nidu/cds/view/p/id/2068/lang/en
In other words, what have you tried?

Is LabVIEW in evaluation mode more slowly?

Hello,
I tried my LabVIEW 8.2 program on a PC with LabVIEW in evaluation mode. I was surprised how slowly the program was. After activation from LabVIEW the program runs much quicker. I will often install LabVIEW by customers in evaluation mode during the implementation phase.
So it's important for me to know if LabVIEW is in evaluation mode noticeable more slowly than after activation.
Thanks for answers
Thomas Bartels

I have not noticed any speed differences between licensed and evaluation modes.
R

NI LabVIEW RIO Evaluation Kit

Similar Messages

Maybe you are looking for